BMW 1 Series E82 (2008-2013)

Clear BMW chassis

Please ensure your correct model is selected

Sub-Categories

Sort By:

Rogue Engineering - Corporate Logo
T#:641617
Part#: TM
In Stock
$ 69.00 USD
Free Shipping
$ 69.00 USD
Free Shipping
Unlike other aftermarket mounts, the mounting plate and studs of our mounts have been Zinc-plated to prevent corrosion. Rogue Engineering Transmission Mounts are sold as a pair, and come with Grade 8 Zinc plated hardware. Rogue Engineering transmission mounts are designed with street comfort in mind while still reducing left and right movement of the transmission. By using a cylindrical shape instead of the factory hourglass like design and utilizing Neoprene rubber deflection can be significantly reduced, minimizing unwanted transmission movement while maintaining vibration dampening characteristics.
Show More Show Less
AeroCatch - Corporate Logo
T#:340098
Part#: AEROCATCH
In Stock
$ 566.99

This product was last offered at the strikethrough price on
05-13-2026

Starting at $ 82.99 USD
Free Shipping
Starting at $ 82.99 USD
Free Shipping
As used by Turner Motorsport on our championship winning BMW race cars, the new aerodynamically efficient and aesthetically styled AeroCatch is setting new standards in hood fixing for the 21st century. Say goodbye to your standard hood pins -- these are better all around.
Show More Show Less
Rogue Engineering - Corporate Logo
T#:27105150
Part#: RE.061
In Stock
$ 119.00 USD
Free Shipping
$ 119.00 USD
Free Shipping
You are looking at the BEST license plate bracket for your BMW, price no object! We never understood why BMW would put a cheap, plastic bracket on the back of a BMW to hold a license plate. The screws holding the bracket on would rust, the steel inserts hold the plate on would also rust, causing the hardware holding the plate on to seize or just no longer function. Our bracket fits any BMW that mounts license plates in the rear that use factory part number 51-18-8-238-061. Fits most BMWs produced AFTER 1999. If your vehicle does not use the plastic plate, it will not fit. Does not fit E46 touring (wagon). PROBLEMS with the factory bracket and hardware The screws that secure the plastic bracket are plated steel and will corrode over time. These two screw would normally not be seen since it is under the license plate, but it is holding the bracket onto the trunk. The four (4) nutserts that are pressed into the plastic frame (to hold the license plate) are also steel and will eventually seize with the bolt and just spin in the plastic frame becoming useless. The plastic frame itself is flimsy, doing a near minimal task of holding on the license plate. The hardware securing the plate to the bracket will rust, seizing to the nutsert or even spinning in place becoming completely useless. SOLUTION Create a more robust bracket that would not only be stiffer but also more corrosion resistant; CNC’d aluminum with an anodized finish. We machine a near identical plate, matching factory dimensions, from 1/2" plate of aluminum. Instead of nutserts pressed into plastic, map the correct position and machine the threads for the hardware directly into the plate. The hardware used to secure the new bracket to the trunk would be made from stainless steel (or optional corrosion-proof titanium) The hardware used to secure the license plate to the newly engineered bracket would also be stainless steel (or optional made from titanium) Kit Includes: One (1) Rogue Engineering designed and manufactured CNC'd aluminum license plate bracket Two (2) Stainless screws to secure bracket to trunk. Four (4) stainless screws to secure license plate to bracket.
Show More Show Less

KMAC - Corporate Logo
T#:389645
Part#: 192416-1J
In Stock
$ 380.00 USD
Free Shipping
$ 380.00 USD
Free Shipping
Location: Front
Type: Street, Stage 1
Bearing: captive-ball fully encased in polyurethane

These front adjustable camber/caster plates will replace your stock front upper strut bearing. The KMAC plates are a 'floating' design so camber and caster are adjusted together. This design allows maximum range of adjustment since no other hardware interferes with the adjustments. Since these replace your stock strut bearings they are designed to work with a stock-type spring only. And when installed correctly will not significantly alter ride height. Adjustment is easily done by loosening the three nuts on top of the tower and sliding the camber plate into the position you want, then re-tighten the nuts. These mounts can be installed two ways - for camber correction or swapped side-side for increasing negative camber. Detailed instructions included.

Note: suspensions vary from manufacturer to manufacturer. Turner Motorsport cannot be responsible for fitment issues caused by non-stock or specialized coil-over suspensions. As with any race-derived component, additonal fabrication may be required.

This item fits the following BMWs:
2008-2012  E82 BMW  128i 135i
6/1992-1999  E36 BMW  318i 318is 318ti 318ic 323is 323ic 325i 325is 325ic 328i 328is 328ic M3
1999-2005  E46 BMW  323i 323ci 325i 325ci 325xi 328i 328ci 330i 330ci 330xi
2006-2011  E90 BMW  325i 328i 330i 335d 335i - Sedan
2006-2012  E91 BMW  328i - Wagon
2007-2013  E92 BMW  328i 335i 335is - Coupe
2007-2013  E93 BMW  328i 335i - Convertible
1997-2003  E39 BMW  525i 528i 530i 540i (not for cars with EDC)
2004-2010  E60 BMW  525i 530i 528i 535i 545i 550i
2004-2011  E63 E64 BMW  645ci 650i
1997-2002  Z3 BMW  Z3 1.9 Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i M Roadster M Coupe
2003-2008  E85 BMW  Z4 2.5i Z4 3.0i Z4 3.0si
2009+  Z4 BMW  Z4 sDrive28i Z4 sDrive30i Z4 sDrive35i Z4 sDrive35is
2000-2003  E52 BMW  Z8 Roadster (without EDC)
Show More Show Less

KMAC - Corporate Logo
T#:389667
Part#: 193926K
Ships on Oct 2, 2026
$ 480.00 USD
Free Shipping
$ 480.00 USD
Free Shipping
Rear adjustable camber and toe bushings for the E82/E9X non-M 3-series. These bushings allow you to adjust camber and toe beyond factory specs to either restore camber or add more. If you lowered your car and have too much camber these bushings can get you back to stock specs. On the flip side if you need more camber for the track or autocross, you can fine tune it with these too. These bushings press in and replace the existing rubber bushings. They are made from peformance urethane which will give more feedback and response to the driver. Sold as a set with a bushing extraction tool included.

Fits the following BMWs:
E82/88 BMW 2 Series
E89 BMW Z4
E9X BMW Non-M
Show More Show Less

Rogue Engineering - Corporate Logo
T#:553830
Part#: RE.E9X.TA.M3
Ships in 8 Business Days
$ 289.00 USD
Free Shipping
$ 289.00 USD
Free Shipping

When an E9X is lowered beyond the limits of just lowering springs, the rear wheels toe-in excessively. This excessive rear toe leads to premature wear, that many people attribute to an increase in negative camber. It has become a common belief that an extremely low vehicle will wear the tires wrong as a matter of consequence. It has become standard practice to go as low as you can and proceed to replace your tires every five to ten thousand miles. Whats more is that when the vehicle reaches a certain ride height, the factory arms become maxed out and there is no way to compensate and dial in the proper toe. You're left with an improperly aligned vehicle that is in effect worse off than it was with the stock suspension installed.

This is not only uneconomical but improper and unsafe. ECS Tuning is proud to offer a solution for this problem in the form of Rogue Engineering E9X adjustable rear toe arms. These arms allow for greater toe adjustment on vehicles that have been lowered with a coilover suspension. With the toe set properly the tires can contact the road properly this maximizes grip and minimizes wear. 

Features:

  • 100% machined and anodized, 6061-T6 lightweight aluminum arms
  • High-strength, 3-piece, rod end (with carbon fiber reinforced, PTFE race) offers longer life for street compared to standard rod ends
  • SEALS-IT Rod end seals keep dirt, water, and other contaminants out
  • Rod ends feature grease fittings, to allow for rod end serviceability.
  • Lighter than stock!  (Stock is 875g, RE arms are 640g)
  • Extremely easy installation and adjustment (your alignment shop will LOVE you!)
Show More Show Less
Akrapovic - Corporate Logo
T#:340330
Part#: TMS4781
Ships in 5 Business Days
Starting at $ 5,403.80 USD
Free Shipping
Starting at $ 5,403.80 USD
Free Shipping
According to BMW the 1 Series M Coupe is a "predator on the prowl", why not give it some GROWL with the Akrapovic slip-on exhaust system.

This slip-on muffler is an "axle back" system that is mounted on the MotoGP 1M Coupe Safety Car and now is available for street going 1M Coupes. The Akrapovic Slip-On Titanium exhaust system for the BMW 1M Coupe is designed for drivers who demand more power and less weight. In addition to a weight reduction and a power gain, one of the tasks of the Akrapovic team was also to make the sound of the 1M Coupe become music to ones ears. An optional wireless "dualmode" exhaust flap control allows the vehicle to have a more civilized, but deeper than stock sound at low speed. However, when the exhaust flap is opened the muffler is bypassed, creating a deep and sporty sound much more in keeping with the personality of the car.

Not for sale outside the US or Canada.

This item fits the following BMWs:
2011+ E82 BMW 1M Coupe
Show More Show Less

KMAC - Corporate Logo
T#:389646
Part#: 192416-3L
Special Order: No Guaranteed ETA
$ 545.00 USD
Free Shipping
$ 545.00 USD
Free Shipping
Location: Front
Type: Street/Track, Stage 2
Bearings: main PTFE-lined pillow-ball bearing suspended in polyurethane; self-lubricating radial axial bearing/bushing in upper spring plate
Springs: includes OEM size upper spring perch, 60mm upper spring perch, and 2.5" upper spring perch

The Stage 3 KMAC plates are a mixed track and street camber/caster plate meant to be used in a variety of suspensions and setups. Since there is less bushing than on the Stage 1, more noise and vibration will reach the driver. The adjustment design is similar to the Stage 1 with a floating mount that sets camber and caster simultaneously. This design allows maximum range of adjustment since no other hardware interferes with the adjustments. These plates can work on both coil over and stock-stype suspensions and upper spring perches are included for OEM springs, 60mm, and 2.5" coil over springs. The upper perch assembly incorporate a self-sliding radial bushing that allows the spring to spin during its travel instead of bind. This reduces tension on the spring and helps reduce noise and spring 'popping' noises. Bearing inserts, spacers for correct articulating angles, and 3 sizes of upper nut adapters included. The urethane bushings and bearings are replaceable if they wear out. These are designed mainly for adding negative camber for improved handling and not for camber correction back to stock settings (see Stage 1 kit). Basic instructions included but professional installation is required.

Note: suspensions vary from manufacturer to manufacturer. The proper stacked height and clearances are required. K-Mac includes bearing adapters, spacers, and various top nuts but it is still the responsibility of the installer to ensure a correct and safe fitment. As with any race-derived component, additonal fabrication may be required.

This item fits the following BMWs:
2008-2012  E82 BMW  128i 135i
6/1992-1999  E36 BMW  318i 318is 318ti 318ic 323is 323ic 325i 325is 325ic 328i 328is 328ic M3
1999-2005  E46 BMW  323i 323ci 325i 325ci 325xi 328i 328ci 330i 330ci 330xi
2006-2011  E90 BMW  325i 328i 330i 335d 335i - Sedan
2006-2012  E91 BMW  328i - Wagon
2007-2013  E92 BMW  328i 335i 335is - Coupe
2007-2013  E93 BMW  328i 335i - Convertible
1997-2003  E39 BMW  525i 528i 530i 540i (not for cars with EDC)
2004-2010  E60 BMW  525i 530i 528i 535i 545i 550i
2004-2011  E63 E64 BMW  645ci 650i
1997-2002  Z3 BMW  Z3 1.9 Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i M Roadster M Coupe
2003-2008  E85 BMW  Z4 2.5i Z4 3.0i Z4 3.0si
2009+  Z4 BMW  Z4 sDrive28i Z4 sDrive30i Z4 sDrive35i Z4 sDrive35is
2000-2003  E52 BMW  Z8 Roadster (without EDC)
Show More Show Less

KMAC - Corporate Logo
T#:389647
Part#: 192416-2L
Ships in 8 Business Days
$ 545.00 USD
Free Shipping
$ 545.00 USD
Free Shipping
Location: Front
Type: Street/Track, Stage 2
Bearings: main PTFE-lined pillow-ball bearing suspended in polyurethane; self-lubricating radial axial bearing/bushing in upper spring plate
Springs: includes OEM size upper spring perch, 60mm upper spring perch, and 2.5" upper spring perch

The Stage 2 KMAC plates are a mixed track and street camber/caster plate meant to be used in a variety of suspensions and setups. Since there is less bushing than on the Stage 1, more noise and vibration will reach the driver. The adjustment design is similar to the Stage 1 with a floating mount that sets camber and caster simultaneously. This design allows maximum range of adjustment since no other hardware interferes with the adjustments. These plates can work on both coil over and stock-stype suspensions and upper spring perches are included for OEM springs, 60mm, and 2.5" coil over springs. The upper perch assembly incorporate a self-sliding radial bushing that allows the spring to spin during its travel instead of bind. This reduces tension on the spring and helps reduce noise and spring 'popping' noises. Bearing inserts, spacers for correct articulating angles, and 3 sizes of upper nut adapters included. The urethane bushings and bearings are replaceable if they wear out. These are designed mainly for adding negative camber for improved handling and not for camber correction back to stock settings (see Stage 1 kit). Basic instructions included but professional installation is required.

Note: suspensions vary from manufacturer to manufacturer. The proper stacked height and clearances are required. K-Mac includes bearing adapters, spacers, and various top nuts but it is still the responsibility of the installer to ensure a correct and safe fitment. As with any race-derived component, additonal fabrication may be required.

This item fits the following BMWs:
2008-2012  E82 BMW  128i 135i
6/1992-1999  E36 BMW  318i 318is 318ti 318ic 323is 323ic 325i 325is 325ic 328i 328is 328ic M3
1999-2005  E46 BMW  323i 323ci 325i 325ci 325xi 328i 328ci 330i 330ci 330xi
2006-2011  E90 BMW  325i 328i 330i 335d 335i - Sedan
2006-2012  E91 BMW  328i - Wagon
2007-2013  E92 BMW  328i 335i 335is - Coupe
2007-2013  E93 BMW  328i 335i - Convertible
1997-2003  E39 BMW  525i 528i 530i 540i (not for cars with EDC)
2004-2010  E60 BMW  525i 530i 528i 535i 545i 550i
2004-2011  E63 E64 BMW  645ci 650i
1997-2002  Z3 BMW  Z3 1.9 Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i M Roadster M Coupe
2003-2008  E85 BMW  Z4 2.5i Z4 3.0i Z4 3.0si
2009+  Z4 BMW  Z4 sDrive28i Z4 sDrive30i Z4 sDrive35i Z4 sDrive35is
2000-2003  E52 BMW  Z8 Roadster (without EDC)
Show More Show Less
Rogue Engineering - Corporate Logo
T#:553834
Part#: RE.E9X.TA
Back Ordered
$ 339.00 USD
Free Shipping
$ 339.00 USD
Free Shipping

Updated design!  Now shipping!

When an E9X is lowered beyond the limits of just lowering springs, the rear wheels toe-in excessively. This excessive rear toe leads to premature wear, that many people attribute to an increase in negative camber. It has become a common belief that an extremely low vehicle will wear the tires wrong as a matter of consequence. It has become standard practice to go as low as you can and proceed to replace your tires every five to ten thousand miles. Whats more is that when the vehicle reaches a certain ride height, the factory arms become maxed out and there is no way to compensate and dial in the proper toe. You're left with an improperly aligned vehicle that is in effect worse off than it was with the stock suspension installed.

This is not only uneconomical but improper and unsafe. ECS Tuning is proud to offer a solution for this problem in the form of Rogue Engineering E9X adjustable rear toe arms. These arms allow for greater toe adjustment on vehicles that have been lowered with a coilover suspension. With the toe set properly the tires can contact the road properly this maximizes grip and minimizes wear. 

Features:

100% machined and anodized, 6061-T6 lightweight aluminum arms (and collars).

Stainless hardware and spacers are perfect for the tough Northeast climate!

New!  Easy adjustment with 22mm open ended wrench and 5mm allen key!  It only requires 15 ft. lbs. on the clamp to secure the clamp!

New!  Included lock-out kit, replaces factory eccentric hardware.

Updated 3-piece rod ends features 4130 chromoly steel bodies, heat-treated, alloy steel races, and Teflon liners

Extremely easy installation and adjustment (your alignment shop will LOVE you!)

Show More Show Less
Rogue Engineering - Corporate Logo
T#:35829340
Part#: RE_E9X_CAMNO
Ships in 8 Business Days
$ 595.00 USD
Free Shipping on orders $49 and up

Rogue Engineering E82/E9X Adjustable Rear Camber Link Set V2.0 is the ultimate upgrade for BMW enthusiasts seeking enhanced handling, improved tire wear, and precise suspension tuning. This high-performance solution is engineered to fit BMW E82 1-Series and E9X 3-Series models, offering superior adjustability and durability over OEM components. Ideal for street and track use, this camber link set is crafted from premium materials to ensure strength and long-lasting performance.

Key Features:

These replace the wishbone and guide arm links in the factory suspension which have rubber bushings and limited adjustment. Enhanced suspension adjustability for optimized alignment Improves handling and reduces uneven tire wear Compatible with BMW E82 1-Series and E9X 3-Series models Constructed from high-strength materials for durability and reliability Perfect for both street performance and track applications Turner Motorsport proudly offers the Rogue Engineering E82/E9X Adjustable Rear Camber Link Set V2.0, providing BMW drivers with unmatched performance and precision.

Show More Show Less