Looking for coilovers that will provide reliability on street driven vehicles but are also capable of feeding your weekend track demon's desire for performance? BC Racing's BR Series coilover kit may be just the thing for you.

BR Series coilovers are the most popular and versatile option offered by BC racing, offering features such as 30-level dampening adjustment (simultaneous compression and rebound control), linear springs where possible, and a minimum of 2 inches ride height drop. To ensure performance, comfort, and quality, all BR Series kits are Dyno tested during the design stage to determine the best valving and spring rates, then installed and tested for a minimum of 6 months. This kit features mounts and brackets that are fully compatible with all stock mounting points and components.

The upper shock/strut mounts are all constructed of 6061-T6 Aluminum for strength and weight savings. BC Racing design 1 of 3 types of upper mounts for each vehicle: Caster/Camber Plates (+/- 3* camber), Camber Plates (+/- 3* camber), and Rubber Mount Plates (NVH reduction). The included mount option for this kit is shown in the kit specs and features below.

Lower shock mounts are powder coated for corrosion protection and constructed of either 6061-T6 aluminum that has been milled from a single piece (fork or bolt eye mount) or of STKM13C steel with all brackets welded robotically.

The included springs come in one of 3 styles: linear, S-barrel, and V-barrel. Linear springs are used in most applications unless limited by the OE design that does not allow the use of linear springs. All spring options are made from SAE9254 steel and have a zinc coating applied under the powder coating for increased spring corrosion protection and long term reliability.

All shock bodies used in the BR Series coilovers use a 53mm shock body (unless noted otherwise) for added strength, performance, and increased fluid capacity. All shocks are then powder coated black chrome for clean styling and corrosion protection.

Specs and Features:

• 8k Front & 12k Rear Spring Rate
• S-Barrel front & Linear rear springs
• Valved specifically to spring style and rate
• Camber Plates Front Mounts
• Aluminum and Rubber Rear Mounts
• Black Powder Coated Components
• All OE style brackets and mounting for perfect fit
• 30 Levels of Simultaneous Compression and Rebound Dampening
• 2 inch minimum and 3+ Inches of total potential drop
• Great for Track, Street, and any other conditions

The ECS Coilover Line was designed with the "daily drivers" in mind! Focused on improving the performance and aesthetics of your vehicle without forgetting comfort. With 32 levels of available damping and height adjustments tailored to each car, ECS coilovers are right in that sweet spot of firm and compliant while giving you an aggressive look and vastly improved handling.

The ECS Tuning Performance Coilover System provides a sport-tuned, height, damping, and body adjustable suspension with substantial performance benefits using high-quality materials and coatings to replace your worn suspension, all while giving your vehicle that perfect ride height!

PERFORMANCE FEATURES

32 levels of rebound damping adjustment
Integrated camber plates for +/-1.5 degrees of adjustment to dial in your fitment and alignment
Ride height adjustment: 1" - 3.5" drop
Heat treated, progressive rate coil springs.
Adjustable damping, monotube shocks/struts paired with optimized progressive rate coil springs gives your vehicle road-sticking grip with reduced body roll for exceptional confidence in your vehicle's handling. With your vehicle's new, lower ride height the center of gravity is now moved lower, further improving handling performance
Adjustable front bodies allow you to set the ride height while maintaining correct spring pre-load
Adjustable front and rear bodies allow the shock to operate in the correct valving range, regardless of ride height

PRODUCT DESIGN

Strut and shock bodies finished with a durable gloss black powder coat for good looks and great longevity
Threaded portions are are zinc-coated for optimum corrosion protection against rain and salt (finish will vary between clear or black zinc coatings depending on availability)
Coil springs are powder-coated Reflex Silver Metallic finish for durability
Red anodized, billet aluminum spring seats with locking collars allow for quick, on the car, adjustability with the included spanner wrenches
Self-locking, zinc-coated flanged nuts used for shock & strut shaft pins
Zinc coated strut mount securing nuts included
Rear shock adjuster housings are black E-coated for durability
Zinc-coated lower spring perches
Integrated bump stops and dust boots

PRODUCT DEVELOPMENT

ECS Tuning Adjustable Damping Coilover Systems are developed in-house, tested and inspected by the Research & Development team in our Wadsworth, Ohio facility. The highest level of precision and quality through leading-edge product development technology and methods, ensuring the necessary long term product testing was performed on multiple test vehicles in the harshest conditions available.

Looking for coilovers that will provide reliability on street driven vehicles but are also capable of feeding your weekend track demon's desire for performance? BC Racing's BR Series coilover kit may be just the thing for you.

BR Series coilovers are the most popular and versatile option offered by BC racing, offering features such as 30-level dampening adjustment (simultaneous compression and rebound control), linear springs where possible, and a minimum of 2 inches ride height drop. To ensure performance, comfort, and quality, all BR Series kits are Dyno tested during the design stage to determine the best valving and spring rates, then installed and tested for a minimum of 6 months. This kit features mounts and brackets that are fully compatible with all stock mounting points and components.

The upper shock/strut mounts are all constructed of 6061-T6 Aluminum for strength and weight savings. BC Racing design 1 of 3 types of upper mounts for each vehicle: Caster/Camber Plates (+/- 3* camber), Camber Plates (+/- 3* camber), and Rubber Mount Plates (NVH reduction). The included mount option for this kit is shown in the kit specs and features below.

Lower shock mounts are powder coated for corrosion protection and constructed of either 6061-T6 aluminum that has been milled from a single piece (fork or bolt eye mount) or of STKM13C steel with all brackets welded robotically.

The included springs come in one of 3 styles: linear, S-barrel, and V-barrel. Linear springs are used in most applications unless limited by the OE design that does not allow the use of linear springs. All spring options are made from SAE9254 steel and have a zinc coating applied under the powder coating for increased spring corrosion protection and long term reliability.

All shock bodies used in the BR Series coilovers use a 53mm shock body (unless noted otherwise) for added strength, performance, and increased fluid capacity. All shocks are then powder coated black chrome for clean styling and corrosion protection.

Specs and Features:

• 7k Front & 12k Rear Spring Rate
• S-Barrel front & Linear rear springs
• Valved specifically to spring style and rate
• Camber Plate Front Mounts
• Aluminum and Rubber Rear Mounts
• Black Powder Coated Components
• All OE style brackets and mounting for perfect fit
• 30 Levels of Simultaneous Compression and Rebound Dampening
• 2 inch minimum and 3+ Inches of total potential drop
• Great for Track, Street, and any other conditions

The rear lower control arms on E82/E9X models are the weakest link in the rear suspension. The arm is made from folded sheetmetal and it bends and deforms easily. Not only will it deform from potholes and curbs, tow truck drivers love to hook onto them without realizing how weak they are. We have seen other race teams complete the box section to make them stronger. A bent arm will throw off the geometry in the suspension, potentially affecting handling and tire wear. These aluminum arms are both lighter and stronger than the factory sheetmetal arms and is the best solution for chronic bending of the stock arm. These are a direct replacement to your stock arms with no changes needed to your alignment. New high-grade hardware is included.

Note: the stock arm is designed from the factory to be intentionally weak. These arms will bend so that something else in the suspension does not break. Our race cars used the stock sheetmetal arm but we replaced them often. We found that it was better to finish a race with a bent arm than not finish due to a catastrophic failure. The ECS arms are still designed to be the weakest link but are far stronger than the factory arm and will not bend as easily.

This item fits the following BMWs:

2008-2013 E82 E88 BMW 128i 135i 1M Coupe
2006-2011 E90 BMW 325i 325xi 328i 328xi 330i 330xi 335i 335xi M3 - Sedan
2007-2011 E91 BMW 325i 325xi 328i 328xi - Touring Wagon
2007-2013 E92 BMW 328i 328xi 335i 335is 335xi M3 - Coupe
2007-2013 E93 BMW 328i 335i 335is M3 - Convertible

Fine-tuning your coilover damping shouldn’t mean stripping out your rear seats or interior panels. On many applications, rear shock adjusters are hidden behind carpet, trim, or seatbacks, making quick adjustments a hassle.

The ECS Rear Damping Extension Kit solves that problem with a clean and functional solution. These flexible extensions relocate the adjustment knobs to an easily accessible point above the rear shock towers, letting you dial in your suspension from inside the cabin, no disassembly required.

Installation is straightforward: simply drill a small access hole in your interior trim and route the extension cables through. The adjustment knobs can be removed to allow the line to pass through smaller openings, minimizing cutting. For proper installation, be sure to fully loosen the set screw, insert the cable, then securely tighten it using the provided Allen key.

Kit Includes:

(2) Rear damping adjuster extension cables

Installation hardware and Allen key

A smart upgrade for track cars, daily drivers, or anyone who values easy access to suspension tuning, without compromising interior fit and finish.

Upgrade your BMW's suspension with ECS Tuning Adjustable Sway Bar End Links, designed to provide up to 60mm (2.36") of adjustability. These end links allow you to eliminate sway bar preload or fine-tune it for specific racing needs and corner balancing. When installed, they improve drivetrain clearance and enhance sway bar responsiveness by reducing deflection, ensuring superior handling. Perfect for lowered vehicles using springs, coilovers, or air-ride suspension systems, these adjustable sway bar end links allow you to remove unwanted preload caused by changes in the center-to-center distance between sway bar mounting points. By adjusting the end links to a neutral position, you eliminate sway bar preload, enhancing suspension performance in various driving conditions.

The main body of the ECS Sway Bar End Links is crafted from strong, lightweight 6061-T6 billet aluminum and anodized red for superior corrosion resistance. Featuring left and right-hand threaded center sections and machined hex wrench fittings, these end links allow for quick and easy on-the-car adjustments. Zinc-plated hardware ensures secure and lasting adjustments, while the heavy-duty ball joint ends come with weather-resistant rubber boots and stainless steel wire retainers, providing superior protection against salt, rain, and ozone for extended durability. Each kit also includes zinc-plated Nyloc nuts and hardened steel washers for secure installation and improved contact surface on the sway bar.

These end links are designed, engineered, and rigorously tested by ECS Tuning to ensure the highest quality. Whether you have a lowered or stock suspension, these adjustable sway bar end links are the perfect upgrade, offering a high-quality, heavy-duty replacement that fits your specific needs.

Features:

Range of Adjustment: 255mm (10") to 315mm (12.4") 6061-T6 Billet Aluminum Construction: Red anodized for superior corrosion resistance Zinc-Plated Hardware: Provides durability and superior corrosion protection Right and Left-Hand Threaded Center Sections: Quick and simple on-the-car adjustments Heavy-Duty Ball Joints (M10x1.5): Weather-resistant rubber boots and stainless steel wire retainers for long-lasting durability NOTE: If you've modified your vehicle's suspension with aftermarket struts or coilovers, the mounting location for the sway bar end link may have moved. To confirm fitment with our adjustable end links, please measure the distance between the sway bar and the mounting location on the strut body with the vehicle at ride height and confirm that it is within the 255 mm - 315mm range of adjustment.

To reduce the understeering affects of a staggered wheel setup you want a balanced set of sway bars. ECS has configured this anti-roll bar set for E82 1-series and E9X 3-series with a 28mm front bar and a 15mm rear bar. This kit is designed to help reduce the amount of body roll when cornering and enhance response when turning. These anti-roll bars include urethane bushings with a reinforced inner liner that eliminates squeaks and doesn't require lubrication. The bars are powder coated for durability and good looks.

These bars fit in the stock locations using the existing brackets and links. Adjustable links are not required but recommended if the car is lowered or if you have coil overs.

This item fits the following BMWs: 
2008-2013 E82 E88 BMW 128i 135i 1M Coupe
2006-2011 E90 BMW 325i 328i 330i 335d 335i M3 - Sedan
2007-2011 E91 BMW 325i 328i - Touring Wagon
2007-2013 E92 BMW 328i 335i 335is M3 - Coupe
2007-2013 E93 BMW 328i 335i 335is M3 - Convertible

Since established in 2004, GSP North America has positioned itself as a leading supplier of New Axles in North America.GSP’s new axle program consistently offers the best application coverage, most SKU count, and more new numbers than any other competitors. GSP’s hub assembly program was introduced to North America market in 2010 and has grown into one the most trustable programs in US market.

This item fits the following BMWs: 

E82/88 BMW 128i 135i

E90/92 BMW 325i 328i 328i xDrive 330i 335i

Revamp Your Suspension with the BMW & MINI Coilover Wrench Set

• Compatible with BMW and MINI models for versatile use
• Durable construction ensures long-lasting performance
• Ergonomic design provides comfortable handling during installation
• Allows for precise adjustment of coilovers for optimal ride quality

Upgrade your BMW or MINI's suspension system with the BMW & MINI Coilover Wrench Set. This set is compatible with various BMW and MINI models, offering versatile compatibility for a wide range of vehicles. Constructed from durable materials, these wrenches are built to withstand the rigors of frequent use and provide long-lasting performance. The ergonomic design ensures comfortable handling during installation, reducing fatigue and allowing for more efficient work. With the BMW & MINI Coilover Wrench Set, you can easily adjust your coilovers to achieve the optimal ride quality for your vehicle.