BMW Suspension Parts for BMW 1 Series E82 (2008-2013)

KMAC Stage 1 Street Front Adjustable Camber/Caster Plates - E36, E39 ...

T#:389645

Part#: 192416-1J

In Stock

$ 380.00 USD

Add to Wish List

Qty

$ 380.00 USD

Add to Wish List

Location: Front
Type: Street, Stage 1
Bearing: captive-ball fully encased in polyurethane

These front adjustable camber/caster plates will replace your stock front upper strut bearing. The KMAC plates are a 'floating' design so camber and caster are adjusted together. This design allows maximum range of adjustment since no other hardware interferes with the adjustments. Since these replace your stock strut bearings they are designed to work with a stock-type spring only. And when installed correctly will not significantly alter ride height. Adjustment is easily done by loosening the three nuts on top of the tower and sliding the camber plate into the position you want, then re-tighten the nuts. These mounts can be installed two ways - for camber correction or swapped side-side for increasing negative camber. Detailed instructions included.

Note: suspensions vary from manufacturer to manufacturer. Turner Motorsport cannot be responsible for fitment issues caused by non-stock or specialized coil-over suspensions. As with any race-derived component, additonal fabrication may be required.

This item fits the following BMWs:
2008-2012 E82 BMW 128i 135i
6/1992-1999 E36 BMW 318i 318is 318ti 318ic 323is 323ic 325i 325is 325ic 328i 328is 328ic M3
1999-2005 E46 BMW 323i 323ci 325i 325ci 325xi 328i 328ci 330i 330ci 330xi
2006-2011 E90 BMW 325i 328i 330i 335d 335i - Sedan
2006-2012 E91 BMW 328i - Wagon
2007-2013 E92 BMW 328i 335i 335is - Coupe
2007-2013 E93 BMW 328i 335i - Convertible
1997-2003 E39 BMW 525i 528i 530i 540i (not for cars with EDC)
2004-2010 E60 BMW 525i 530i 528i 535i 545i 550i
2004-2011 E63 E64 BMW 645ci 650i
1997-2002 Z3 BMW Z3 1.9 Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i M Roadster M Coupe
2003-2008 E85 BMW Z4 2.5i Z4 3.0i Z4 3.0si
2009+ Z4 BMW Z4 sDrive28i Z4 sDrive30i Z4 sDrive35i Z4 sDrive35is
2000-2003 E52 BMW Z8 Roadster (without EDC)

Show More Show Less

IRP Rear Lower Shock Mount Set - E8X E9X Non-M

T#:587022

Part#: IRPRSM-90B

Ships on Sep 23, 2026

$ 195.00 USD

Add to Wish List

Qty

$ 195.00 USD

Add to Wish List

The stock rubber lower shock mounts tend to fail prematurely, especially when subjected to rough track conditions. These IRP lower shock mounts utilize a monoball design that is significantly stronger and helps to eliminate deflection that is caused by soft rubber. Key Benefits: Monoball rear lower shock mount eliminates unwanted deflection, maximizing shock efficiency and performance. Allows full shock body articulation for low friction movement and reduced side loading and improved shock wear. Designed to work with stock non-M taper seat stud style shocks (not M eyelet mount type). Maintains OE shock position

Show More Show Less

Set of Rear Lower Shock Mounts

T#:7164814

Part#: IRPRSM-90PU

Ships in 1 Business Day

$ 141.99 USD

Add to Wish List

Qty

$ 141.99 USD

Add to Wish List

Rear Lower Shock Mounts - Set With Polyurethane Inserts BMW E8X, E9X (not M Models)

KMAC Adjustable Rear Camber And Toe Bushings Set - E82, E89, E9X non-...

T#:389667

Part#: 193926K

Ships on Oct 1, 2026

$ 480.00 USD

Add to Wish List

Qty

$ 480.00 USD

Add to Wish List

Rear adjustable camber and toe bushings for the E82/E9X non-M 3-series. These bushings allow you to adjust camber and toe beyond factory specs to either restore camber or add more. If you lowered your car and have too much camber these bushings can get you back to stock specs. On the flip side if you need more camber for the track or autocross, you can fine tune it with these too. These bushings press in and replace the existing rubber bushings. They are made from peformance urethane which will give more feedback and response to the driver. Sold as a set with a bushing extraction tool included.

Fits the following BMWs:
E82/88 BMW 2 Series
E89 BMW Z4
E9X BMW Non-M

Show More Show Less

Rear Subframe Bushings/Mounts - Set - Group N Race Rubber - E82, E9X ...

T#:12076

Part#: E9X-GPN-SUBFRAME

In Stock

$ 800.00 USD

Add to Wish List

Qty

$ 800.00 USD

Add to Wish List

The E82 and E90/E92 subframes have an inherent weakness in the rear subframe - the mounts are too soft for the power and torque these cars are capable of. The subframe is the heart of a BMW's rear suspension. As torque is transmitted through the differential and axles and as the tires grip the road, the subframe mounts are working to keeping everything in line. That's a tough task to hold when torque is increased with bigger boost (335i) or even mild tweaks (M3). While the M3 subframe mounts are a great upgrade for the non-M chassis these factory BMW Motorsport subframe mounts go one step further.

These Motorsport/Group N rear subframe bushings are a direct replacement upgrade over the stock mounts. They are rubber to conform to the rules of the Group N racing class - so they are still acceptable for street use as long as extra ride harshness can be tolerated. The rear subframe has to come down from the car for these mounts to be pressed in. So now is the perfect time to do other work as well - check out our other Motorsport Race bushings or M3 upgrades.

Price is for the set of 4 mounts.

This item fits the following BMWs:
2008-2012 E82 BMW 128i 135i 1M Coupe
2006-2011 E90 BMW 325i 325xi 328i 328xi 328i xDrive 330i 330xi 335d 335i 335xi 335i xDrive M3 - Sedan
2006-2012 E91 BMW 325xi 328i 328xi 328i xDrive - Wagon
2007-2013 E92 BMW 328i 328xi 328i xDrive 335i 335is 335xi 335i xDrive M3 - Coupe
2007-2013 E93 BMW 328i 335i M3 - Convertible

Show More Show Less

Front Upper Control Arm Bushing Set (FCAB) - Group N Race Rubber - E8...

T#:2309

Part#: E9X-GPN-UCAB

Ships in 8 Business Days

$ 413.38 USD

Add to Wish List

Qty

$ 413.38 USD

Add to Wish List

These are the factory BMW Motorsport Group N high performance front upper control arm bushings. These heavy duty rubber bushings are stiffer than the stock bushings to improve steering feel and improve handling. They are great for track use - and Grand Am Cup legal! - yet can also be used on a street driven car - please note these will not be as compliant as the stock rubber bushings. These are for the control arm with the ball joint pointing down, sometimes referred to as the thrust arm or tension strut.

Price is for the pair of bushings.

This item fits the following BMWs:
2008-2012 E82 BMW 128i 135i 1M
2006-2011 E90 BMW 325i 328i 330i 335d 335i M3 - Sedan
2006-2011 E91 BMW 328i - Wagon
2007-2012 E92 BMW 328i 335i 335is M3 - Coupe
2007-2012 E93 BMW 328i 335i M3 - Convertible

Show More Show Less

KMAC Stage 2 Street/Track Front Adjustable Camber/Caster Plates - E36...

T#:389647

Part#: 192416-2L

Ships in 9 Business Days

$ 545.00 USD

Add to Wish List

Qty

$ 545.00 USD

Add to Wish List

Location: Front
Type: Street/Track, Stage 2
Bearings: main PTFE-lined pillow-ball bearing suspended in polyurethane; self-lubricating radial axial bearing/bushing in upper spring plate
Springs: includes OEM size upper spring perch, 60mm upper spring perch, and 2.5" upper spring perch

The Stage 2 KMAC plates are a mixed track and street camber/caster plate meant to be used in a variety of suspensions and setups. Since there is less bushing than on the Stage 1, more noise and vibration will reach the driver. The adjustment design is similar to the Stage 1 with a floating mount that sets camber and caster simultaneously. This design allows maximum range of adjustment since no other hardware interferes with the adjustments. These plates can work on both coil over and stock-stype suspensions and upper spring perches are included for OEM springs, 60mm, and 2.5" coil over springs. The upper perch assembly incorporate a self-sliding radial bushing that allows the spring to spin during its travel instead of bind. This reduces tension on the spring and helps reduce noise and spring 'popping' noises. Bearing inserts, spacers for correct articulating angles, and 3 sizes of upper nut adapters included. The urethane bushings and bearings are replaceable if they wear out. These are designed mainly for adding negative camber for improved handling and not for camber correction back to stock settings (see Stage 1 kit). Basic instructions included but professional installation is required.

Note: suspensions vary from manufacturer to manufacturer. The proper stacked height and clearances are required. K-Mac includes bearing adapters, spacers, and various top nuts but it is still the responsibility of the installer to ensure a correct and safe fitment. As with any race-derived component, additonal fabrication may be required.

This item fits the following BMWs:
2008-2012 E82 BMW 128i 135i
6/1992-1999 E36 BMW 318i 318is 318ti 318ic 323is 323ic 325i 325is 325ic 328i 328is 328ic M3
1999-2005 E46 BMW 323i 323ci 325i 325ci 325xi 328i 328ci 330i 330ci 330xi
2006-2011 E90 BMW 325i 328i 330i 335d 335i - Sedan
2006-2012 E91 BMW 328i - Wagon
2007-2013 E92 BMW 328i 335i 335is - Coupe
2007-2013 E93 BMW 328i 335i - Convertible
1997-2003 E39 BMW 525i 528i 530i 540i (not for cars with EDC)
2004-2010 E60 BMW 525i 530i 528i 535i 545i 550i
2004-2011 E63 E64 BMW 645ci 650i
1997-2002 Z3 BMW Z3 1.9 Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i M Roadster M Coupe
2003-2008 E85 BMW Z4 2.5i Z4 3.0i Z4 3.0si
2009+ Z4 BMW Z4 sDrive28i Z4 sDrive30i Z4 sDrive35i Z4 sDrive35is
2000-2003 E52 BMW Z8 Roadster (without EDC)

Show More Show Less

KMAC Stage 3 Street/Track Front Adjustable Camber/Caster Plates - E36...

T#:389646

Part#: 192416-3L

Special Order: No Guaranteed ETA

$ 545.00 USD

Add to Wish List

Qty

$ 545.00 USD

Add to Wish List

Location: Front
Type: Street/Track, Stage 2
Bearings: main PTFE-lined pillow-ball bearing suspended in polyurethane; self-lubricating radial axial bearing/bushing in upper spring plate
Springs: includes OEM size upper spring perch, 60mm upper spring perch, and 2.5" upper spring perch

The Stage 3 KMAC plates are a mixed track and street camber/caster plate meant to be used in a variety of suspensions and setups. Since there is less bushing than on the Stage 1, more noise and vibration will reach the driver. The adjustment design is similar to the Stage 1 with a floating mount that sets camber and caster simultaneously. This design allows maximum range of adjustment since no other hardware interferes with the adjustments. These plates can work on both coil over and stock-stype suspensions and upper spring perches are included for OEM springs, 60mm, and 2.5" coil over springs. The upper perch assembly incorporate a self-sliding radial bushing that allows the spring to spin during its travel instead of bind. This reduces tension on the spring and helps reduce noise and spring 'popping' noises. Bearing inserts, spacers for correct articulating angles, and 3 sizes of upper nut adapters included. The urethane bushings and bearings are replaceable if they wear out. These are designed mainly for adding negative camber for improved handling and not for camber correction back to stock settings (see Stage 1 kit). Basic instructions included but professional installation is required.

Note: suspensions vary from manufacturer to manufacturer. The proper stacked height and clearances are required. K-Mac includes bearing adapters, spacers, and various top nuts but it is still the responsibility of the installer to ensure a correct and safe fitment. As with any race-derived component, additonal fabrication may be required.

This item fits the following BMWs:
2008-2012 E82 BMW 128i 135i
6/1992-1999 E36 BMW 318i 318is 318ti 318ic 323is 323ic 325i 325is 325ic 328i 328is 328ic M3
1999-2005 E46 BMW 323i 323ci 325i 325ci 325xi 328i 328ci 330i 330ci 330xi
2006-2011 E90 BMW 325i 328i 330i 335d 335i - Sedan
2006-2012 E91 BMW 328i - Wagon
2007-2013 E92 BMW 328i 335i 335is - Coupe
2007-2013 E93 BMW 328i 335i - Convertible
1997-2003 E39 BMW 525i 528i 530i 540i (not for cars with EDC)
2004-2010 E60 BMW 525i 530i 528i 535i 545i 550i
2004-2011 E63 E64 BMW 645ci 650i
1997-2002 Z3 BMW Z3 1.9 Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i M Roadster M Coupe
2003-2008 E85 BMW Z4 2.5i Z4 3.0i Z4 3.0si
2009+ Z4 BMW Z4 sDrive28i Z4 sDrive30i Z4 sDrive35i Z4 sDrive35is
2000-2003 E52 BMW Z8 Roadster (without EDC)

Show More Show Less

IRP Performance Rear Lower Control Arm Bushing - Inner - 8x, E9x, F87...

The lowest arm housing the coil spring

T#:2408498

Part#: IRPRSB-9XMB2

Special Order: No Guaranteed ETA

$ 176.99 USD

Add to Wish List

Qty

$ 176.99 USD

Add to Wish List

Enhance road feel and keep your vehicle more planted with these upgraded aluminum bushings. Less play allows for more precise suspension articulation, making for a better performance driving experience.

Show More Show Less

Rear Toe Arm Bushing - Inner + Outer - Group N Race Rubber - E82, E9X...

T#:12075

Part#: E9X-GPN-TOE

Ships on Oct 7, 2026

$ 279.99 USD

Add to Wish List

Qty

$ 279.99 USD

Add to Wish List

These BMW Motorsport Group N Bushings replace all of the bushings on the factory toe control arm (also known as the track strut). These inner and outer bushings feature a heavy duty rubber that is stiffer than stock. The stiffer bushing reduces deflection and twist in the arm, leading to more stable handling and faster response in the suspension. These bushings are great for track use and legal for some racing classes yet can also be used on a street driven car where extra ride harshness can be tolerated.

Sold as a set of 4 - two bushings for each toe arm.

This item fits the following BMWs:
2008-2012 E82 BMW 128i 135i
2006-2011 E90 BMW 325i 325xi 328i 328xi 328i xDrive 330i 330xi 335d 335i 335xi 335i xDrive - Sedan
2006-2012 E91 BMW 325xi 328i 328xi 328i xDrive - Wagon
2007-2013 E92 BMW 328i 328xi 328i xDrive 335i 335is 335xi 335i xDrive - Coupe
2007-2013 E93 BMW 328i 335i - Convertible

Show More Show Less

Rear Guide Rod, Upper Link Bushing - Outer - Group N Race Rubber - E8...

T#:3093

Part#: E9X-GPN-FOLB

Ships on Oct 7, 2026

$ 519.80 USD

Add to Wish List

Qty

$ 519.80 USD

Add to Wish List

These are BMW Motorsport Group N Rear Outer bushings for the Guide Rod and Upper Link (Wishbone). This is a heavy-duty rubber that is stiffer than stock to resist deflection and twist in the arm. You'll have more stable handling and faster response in the suspension. These bushings are great for track use and legal for some racing classes yet can also be used on a street driven car where extra ride harshness can be tolerated.

Sold as a set of 4 -
2 Upper Link Outer Bushings,
2 Guide Rod Outer Bushings

This item fits the following BMWs:
2008-2012 E82 BMW 128i 135i
2006-2011 E90 BMW 325i 325xi 328i 328xi 328i xDrive 330i 330xi 335d 335i 335xi 335i xDrive - Sedan
2006-2012 E91 BMW 325xi 328i 328xi 328i xDrive - Wagon
2007-2013 E92 BMW 328i 328xi 328i xDrive 335i 335is 335xi 335i xDrive - Coupe
2007-2013 E93 BMW 328i 335i - Convertible

Show More Show Less

IRP Rear Adjustable Upper Control Arms

T#:2423565

Part#: IRPRSW-9XMMSR

Ships on Nov 10, 2026

Starting at $ 626.99 USD

Add to Wish List

Starting at $ 626.99 USD

Add to Wish List

Featuring Fluro Bearings

Project Cars

SELECT YOUR BMW

BMW Suspension Parts for BMW 1 Series E82 (2008-2013)

Sub-Categories

KMAC Stage 1 Street Front Adjustable Camber/Caster Plates - E36, E39 ...

IRP Rear Lower Shock Mount Set - E8X E9X Non-M

Set of Rear Lower Shock Mounts

KMAC Adjustable Rear Camber And Toe Bushings Set - E82, E89, E9X non-...

Rear Subframe Bushings/Mounts - Set - Group N Race Rubber - E82, E9X ...

Front Upper Control Arm Bushing Set (FCAB) - Group N Race Rubber - E8...

KMAC Stage 2 Street/Track Front Adjustable Camber/Caster Plates - E36...

KMAC Stage 3 Street/Track Front Adjustable Camber/Caster Plates - E36...

IRP Performance Rear Lower Control Arm Bushing - Inner - 8x, E9x, F87...

Rear Toe Arm Bushing - Inner + Outer - Group N Race Rubber - E82, E9X...

Rear Guide Rod, Upper Link Bushing - Outer - Group N Race Rubber - E8...

IRP Rear Adjustable Upper Control Arms

Select Vehicle

Category

Brand

Price

Shipping

Narrow Results