Transmission and Differential Tools for BMW 1 Series E82 (2008-2013)

Schwaben offers the right tools to make your next project a success. Everything from complex engine scanners to brake bleeders and spring compressors, Schwaben tools has you covered.

Some of the recommended use include but are not limited to:

• Remove and install rear ball joints on E38, E39, E60/61, E63/64, E65/66, and E70's
• Removal and installation of ball joints and bushings on rear control arms on E36, E46, E39, E60/61, E63/64,  E65/66, E70, E83 and E85/86 Z4's
• Removal and installation of rear sub frame mounted differential bushings on E36, E46, E83 and E85/86 Z4's
• Removal and installation of rear differential mounted bushings on E36, E46, E9X, E60/61, E63/64, E65/66, and E85/86 Z4's

This hand held Schwaben tool makes changing fluids an easy, quick task.The Schwaben fluid suction/fill pump suitable for oils, water and any non corrosive liquid.

Features 

• Comes with a flexible and a rigid tube. 
• Flow rate is adjustable for different functions.
• 350 ML capacity
• Cylinder is marked in 20 mL increments and fraction of quarts for accurate filling. 

Not for use with gasoline.

Commonly used when replacing axle shaft boots.

Features:

• Crimp and flatten design
• Produces a clean factory style crimp
• Limited Lifetime Warranty

Elevate your lifting experience with the Schwaben Long Low Profile - High Lift Floor Jack. Certified for excellence and designed with a keen understanding of European car enthusiasts' needs, this jack is a testament to precision, durability, and performance. Don't compromise on quality—choose the Schwaben advantage for all your lifting endeavors.

Designed with precision, crafted for performance, and backed by our lifetime replacement program, the Schwaben Long Low Profile - High Lift Floor Jack is a must-have tool for every European car aficionado. This jack is engineered to cater to the unique needs of low ground clearance vehicles, ensuring that your prized possessions are lifted with care and precision.

Key Features:

• One Pump Reach: With its innovative one-pump feature, this floor jack effortlessly reaches contact on most cars, streamlining your lifting process.
• Low Profile Advantage: Boasting a mere 2-3/4" low height and a deep-reach lift arm, this jack is tailored for those sports cars and luxury vehicles that ride close to the ground.
• Hydraulic System Protection: The dual pump pistons are expertly shielded to thwart contaminants from compromising the hydraulic system's integrity.
• Built for Durability: Crafted with heavy gauge construction and fortified with rolled edges, this floor jack guarantees unwavering strength and longevity.
• Precise Control: The U-Joint release mechanism offers meticulous control over load descent at any handle position, ensuring the safety of both you and your vehicle.
• Maneuverability Redefined: Upgraded casters allow seamless maneuverability and effortless positioning of the jack, empowering you to find that perfect lifting spot.
• Safety First: The internal by-pass valve prevents over-pumping, shielding the hydraulic system from stress-induced issues.
• Vehicle Protection: A full cover rubber saddle pad and a protective foam cover on the handle are in place to prevent any unintended damage during the lifting process.
• Impressive Capacity: With a remarkable 4000 lb. capacity, this jack is ready to tackle a range of European vehicles.
• LIFETIME REPLACEMENT: Like almost all Schwaben products, this jack is backed by our lifetime replacement program in case anything goes wrong!

Specifications:

• Min Height: 2-3/4"
• Max Height: 24"
• Handle Length: 49-1/4"
• Jack Body Length: 35"
• Length from Pivot Point to Center of Jack Pad: 22"
• Front Casters: 2-1/2" diameter x 2" width
• Saddle Diameter: 4" with full saddle pad
• Weight Capacity: 4000 lbs.
• ANSI / ASME PALD 2009 Certified

Also included are the Schwaben Aluminum 3-Ton Jack Stands. These ultra-light Schwaben jack stands only weigh 4.7 lbs each. Fit and finish on these stands show how much pride in workmanship goes into our stands. These stands feature all-aluminum construction with heavy-duty flanged bases to safely stabilize loads. Features 6 locking positions for a secure load in multiple heights. The load pin is extra heavy duty at .584 in. diameter and features a posi lock ball to ensure the pin stays in place.  

• Min. Height is 10.6".
• Max Height is 15.4".
• Large 7" diameter base.
• Outer support tube is 2-1/8" in diameter.

For replacement parts, please call us and ask for:

• ES#4430428 - Replacement Screw Set
• ES#4430429 - Replacement Front Wheel
• ES#4430430 - Replacement Caster Wheel

WARNING: This product contains chemicals known to the state of California to cause cancer, birth defects, and/or reproductive harm. See above warning label as well as http://www.p65warnings.ca.gov for further information on Proposition 65 warnings.

Perfect for any job when it comes to keeping your hands clean and protected.

Features:

• High dexterity
• Elastic hook and loop strap
• Textured latex finger tips for grip
• Breathable material

 A complete set offered to ensure that the proper lifting techniques are at use. It's never wise to work under a vehicle supported by only a floor jack, with this complete kit you get a complete matching set to get the job done safe and fast.

• Special low profile thick frame side plates and reinforced lift arm for added strength and use.
• Wide track front wheels help provide chassis torsion control and durability.
• Angular positioned pump pistons provide maximum effective pump stroke even when jack is completely under the vehicle.
• Ball bearing mounted rear swivel caster wheels for easy maneuverability.
• Side mounted handles for carrying and easy positioning.
• Overload and bypass safety valve prevents jack overload and over extension.
• Two piece quick release padded handle for storage or transport.
• Dual piston's for 5 pump full extension

Details:

• Jack Capacity 2 Ton
• Max Lift Height 20"
• Low Height 3.25"
• Chassis Length 26.5"
• Overall Width 13"
• Saddle Diameter 4.5"
• Handle Lenght 50"
• Shipping Weight 50 lbs

Schwaben 12" wheel Stands:

These stands are made from special EPS foam with an anti-skid coating.

Won't scratch or mark your floors!

Lightweight at only 5 lbs each, makes these stands easy to carry and maneuver.

Works on virtually any surface, including sand!

Will not scoot, slip or slide, no matter the surface.

Specs:

12" tall,15.75" long,12" wide.

Works on wheel diameters from 25 to 30 inches.