Turbos for BMW 1 Series E82 (2008-2013)

Clear BMW chassis

If more boost and reliability are your goals choose from one of our BMW turbo upgrades. Our turbo upgrades range from stock turbos rebuilt with stronger internals to all-new, ground-up turbo upgrades. BMW turbos such as the N54 are capable of really impressive power numbers on stock engine internals but the factory turbos lack the precise tolerances and reliability that an upgraded unit will deliver. In other words, the stock turbos can only do so much and if big power (>400whp) is your goal a turbo upgrade must be in your plans. Our partners are leading experts in turbo technology and upgrades. Each Stage has been professionally developed and tested. Additional upgrades and tuning may be, or is, required. Contact us for more details on tuning options.

Sub-Categories

Sort By:

Pure Turbo Heavy Duty N55 Pneumatic Wastegate Actuator - BMW N55 3.0L...

T#:17771605

Part#: HDN55WG

In Stock

$ 160.99 USD

Add to Wish List

Qty

$ 160.99 USD

Add to Wish List

The early N55 turbocharger is notorious for pneumatic wastegate actuator failure, a common issue that triggers frustrating boost errors and persistent check engine lights. Because BMW does not provide this specific component as a standalone replacement, owners are often left with few official repair options. Pure Turbos solves this problem with an upgraded actuator engineered to fix the inherent weaknesses of the original equipment while simultaneously boosting the efficiency of the entire turbocharging system. One of the primary benefits of this enhanced actuator is its ability to deliver approximately 2 psi of additional boost compared to the factory unit while maintaining the same Wastegate Duty Cycle. By optimizing how exhaust gases are managed and bypassed, this component allows the engine to generate more power without requiring more effort from the electronics. This increased pressure translates directly into sharper throttle response and a noticeable jump in horsepower, making it an essential upgrade for drivers who want to restore their vehicle's reliability while enjoying a more aggressive and responsive driving experience.

Show More Show Less

Pure Turbos N55 PURE500 Turbo Upgrade - BMW N55 3.0L w/ PWG

PWG models only

T#:13957903

Part#: N55PURE500PWG

In Stock

$ 1,136.99

This product was last offered at the strikethrough price on
07-07-2026

$ 1,095.00 USD

Add to Wish List

Qty

$ 1,095.00 USD

Add to Wish List

These PURE500 turbos from Pure Turbos are sure to give your car the extra oomph you're looking for! With easy installation and a stealth stock appearance, there is no better stage 1 turbo option for your N55!

Show More Show Less

VTT N54 Billet Vacuum (Boost Control) Tank Kit - Anodized Blue - BMW ...

2X Entries Into Our F80 M3 Sweepstakes

T#:7530040

Part#: VACUUMCANBLUE

In Stock

$ 199.99 USD

Add to Wish List

Qty

$ 199.99 USD

Add to Wish List

VTT is proud to offer their billet replacement for the factory plastic vacuum tanks that store vacuum from the pump and use it to regulate boost via the solenoids. The stock plastic can and small plastic nipples on the stock cans have a tendency to crank over time, and if they leak you will get low boost, or no boost, and poor performance. These cans do away with the weak plastic cans while adding some pop, and color to your engine bay. These vacuum cans retain ALL of the factory provisions including mounting points but come with 90-degree fittings for easier routing of the lines VTT's cans are made of 6061-T6 aluminum, and anodized in 4 colors for beauty, and long life. They also knurl the cans for a very distinct look in the engine bay! VTT also designed these cans to complement their N54 Billet lineup – N5X Billet Oil caps, N5XBillet Oil filter housing caps, Billet coolant cap, Billet valve cover, billet oil cooler block off plate, and Billet Power Steering cap, and so on. All will have matching color These cans are offered in 4 colors – Red, Black, Blue, and Clear anodize The kit will include: 2 – Vacuum canisters (color of choice) 4 – billet 90-degree barbed fittings Requires the additional use of aftermarket vacuum line - Vacuum line not included. Replaces Genuine BMW Vacuum Canisters # 11652247620

Show More Show Less

TurboSmart OPR V2 Oil Pressure Regulator

T#:28504207

Part#: TS-0811-0012

In Stock

10% off MSRP $ 189.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 170.99 USD

Add to Wish List

Qty

10% off MSRP

$ 189.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 170.99 USD

Add to Wish List

Introducing Turbosmart’s OPR V2 Turbocharger Oil Pressure Regulator, a cutting-edge solution launched in 2022 that ensures steady oil pressure for your turbocharger. This innovative regulator features a return-less design with an integrated 44 Micron Stainless Steel Mesh Oil Filter, providing robust performance and protection.

The OPR V2 is the first of its kind, utilizing Turbosmart’s proprietary flow control method to maintain optimal oil pressure regardless of engine oil variables like pressure or temperature. It guarantees a smooth oil flow to your turbocharger, safeguarding critical components such as Exhaust Drive, Back & Charge Pressures from excessive oil pressure that could lead to oil consumption and smoke.

Gone are the days of guesswork with restrictors and complex plumbing for oil pressure regulation. The OPR V2 simplifies the process with its return-less, inline installation and the convenience of a built-in 44 Micron Oil Filter. This filter, made of serviceable and replaceable Stainless Steel Mesh, adds an extra layer of defense against engine oil debris that could harm your turbocharger.

Key Features:

Innovative Patent Pending Design Durable Aluminium (6262 T6) Anodised Body & Valve Regulated Oil Pressure Compatible with Most turbochargers Integrated Stainless Steel (304) Mesh Oil Filter -4AN Inlet and Outlet for easy installation 1/8 NPT Sensor/Gauge Port for monitoring Directional Inlet Feed Logic for optimized performance Laminar Flow Output for consistent oil delivery Compatible with all Engine Oils Designed and Manufactured in Australia

Show More Show Less

N54 Turbocharger Installation Kit - Front And Rear

10X Entries Into Our F80 M3 Sweepstakes

T#:15511873

Part#: 114275634530KT

Ships in 9 Business Days

Sale - Save 12% $ 299.95

This product was last offered at the strikethrough price on
05-03-2026

$ 264.60 USD

Add to Wish List

Qty

Sale - Save 12%

$ 299.95

This product was last offered at the strikethrough price on
05-03-2026

$ 264.60 USD

Add to Wish List

Ensure proper sealing when installing the turbos on your N54. Kit includes: 16 - ASA M7x39 studs 16 - Flange nuts All required gaskets and o-rings Water pump install hardware Replacement vacuum hose T-bolt clamps Helpful hints: For complete installation instructions, refer to Haynes Service Manual (ES2500921). Both downpipes must be removed to remove either front or rear turbo. Tie rod end may need to be separated from knuckle for clearance. Steering rack may also need to be rotated away from subframe for access. Valve cover heat shield will need to loosened and pushed upward to get clearance for turbo manifold removal. If studs back out of cylinder head and nuts are seized to studs, replace studs. Thread studs in to head by hand to prevent cross threading. When installing the new studs in the cylinder head, use a high temperature loctite in the cylinder head side, and copper anti-seize on the nut side. To make more room for access to the front turbo, remove the rubber line running in front of the subframe that attaches to the back of the map thermostat and remove the clip. Cut off the OEM clamp and replace it with a new hose clamp as well. Complete removal of the water pump is not required. Detach the water pump from the side of the block and push it out of the way to make more room for access to the front turbo. If water pump is unbolted from the block, the aluminum bolts must be replaced. Torque specs: Bracket to cylinder head: 9Nm Coolant supply line to crankcase: 9Nm Coolant return line to crankcase: 8Nm Coolant return line to turbo: 8Nm Coolant supply line to supply line: 8Nm Exhaust manifold heat shield: 8Nm Oil supply line to crankcase: 20Nm Oil pressure line to turbo: 8Nm Oil return line to crankcase: 8Nm Oil return line to turbo: 8Nm Turbo manifold to head: 20Nm

Show More Show Less

Turbo Coolant Line Kit - E60, E82, E88

10X Entries Into Our F80 M3 Sweepstakes

T#:42099865

Part#: 11537558900TKT

In Stock

Sale - Save 23% $ 253.99

This product was last offered at the strikethrough price on
05-03-2026

$ 194.66 USD

Add to Wish List

Qty

Sale - Save 23%

$ 253.99

This product was last offered at the strikethrough price on
05-03-2026

$ 194.66 USD

Add to Wish List

Prevent overheating issues and protect your turbo system with the Turbo Coolant Line Kit, the complete solution for keeping your N54 engine running at peak performance.

Wastegate Repair Kit - N54

10X Entries Into Our F80 M3 Sweepstakes

T#:41863724

Part#: 116575857456TKT

Ships on Sep 18, 2026

$ 164.99 USD

Add to Wish List

Qty

$ 164.99 USD

Add to Wish List

Get rid of that annoying N54 Wastegate Rattle for good!

BMW Turbocharger Gasket Set

2X Entries Into Our F80 M3 Sweepstakes

T#:15180813

Part#: 298.900

In Stock

$ 130.99

This product was last offered at the strikethrough price on
05-07-2026

$ 94.99 USD

Add to Wish List

Qty

$ 94.99 USD

Add to Wish List

It's always a good idea to replace any gaskets and seals when replacing and reinstalling a turbo in your car!

Boost Solenoid/Pressure Converter - Kit

10X Entries Into Our F80 M3 Sweepstakes

T#:15677490

Part#: 11721439973-KT

In Stock

Sale - Save 45% $ 408.99

This product was last offered at the strikethrough price on
07-14-2026

$ 226.02 USD

Add to Wish List

Qty

Sale - Save 45%

$ 408.99

This product was last offered at the strikethrough price on
07-14-2026

$ 226.02 USD

Add to Wish List

Kit includes both boost solenoids, vacuum hose and T fitting for a easy leak free install

Blue WG38 Gen V Ultra-Gate 38 - 14PSI

T#:22591972

Part#: TS-0551-1011

In Stock at Vendor

10% off MSRP $ 430.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 387.99 USD

Add to Wish List

Qty

10% off MSRP

$ 430.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 387.99 USD

Add to Wish List

The Gen V WG38 Ultra-Gate 38 external wastegate is your cost-effective, high-performance solution. This 38mm external wastegate is meticulously designed for hassle-free bolt-on applications that make use of the 2-bolt flange.

Show More Show Less

Pure Turbos N55 PURE750 Turbo Upgrade - BMW N55 3.0L w/ PWG

PWG models only

T#:13957911

Part#: N55PURE750PWG

Ships in 4 Business Days

$ 3,107.99

This product was last offered at the strikethrough price on
07-13-2026

$ 3,107.00 USD

Add to Wish List

Qty

$ 3,107.00 USD

Add to Wish List

These PURE750 turbos from Pure Turbos are sure to give your car the extra oomph you're looking for! With easy installation and a stealth stock appearance! The craziness pursues with the possibility of 608whp with E30 and meth running 25psi but those numbers could reach upwards of 650+ with other upgrades! crazy. we know, which leaves this as one of the best stage 2 options for your N55!

Show More Show Less

Turbos and Turbocharger Installation Kit - N54

10X Entries Into Our F80 M3 Sweepstakes

T#:55317702

Part#: 13712247398KT5

Ships in 2 Business Days

$ 1,869.81

This product was last offered at the strikethrough price on
08-25-2026

$ 1,869.66 USD

Add to Wish List

Qty

$ 1,869.66 USD

Add to Wish List

Are your factory N54 turbos plagued by the dreaded wastegate rattle, or worse, starting to blow smoke? Don't just replace them—upgrade your ultimate driving machine with the ultimate DIY refresh kit.

Show More Show Less

Wastegate Actuator Refresh Kit - N55

10X Entries Into Our F80 M3 Sweepstakes

T#:56363350

Part#: 11747626351KT2

Ships Today

$ 259.99 USD

Add to Wish List

Qty

$ 259.99 USD

Add to Wish List

Built around OEM quality components tested to withstand severe heat cycles, the Turner Motorsport Boost Control Maintenance Kit restores precise wastegate actuation.

Elring Turbocharger Mounting Kit - BMW E82/88 E9X F22/23 F3X F07/10 F...

2X Entries Into Our F80 M3 Sweepstakes

T#:44733225

Part#: 648.550

Special Order: No Guaranteed ETA

$ 127.99 USD

Add to Wish List

Qty

$ 127.99 USD

Add to Wish List

If you are replacing your N55's turbocharger, it is advisable to replace the mounting hardware and gaskets as well. This Elring kit includes the Exhaust Manifold Gaskets, Turbo Downpipe Gasket, Flange Nuts, Threaded Studs, and O-Ring Seals needed when replacing the N55 turbo

Show More Show Less

Elring Turbo Oil Drain Gasket - BMW N20 N55 S55 B46/B48 B57

2X Entries Into Our F80 M3 Sweepstakes

T#:44733246

Part#: 876.070

Special Order: No Guaranteed ETA

$ 6.99 USD

Add to Wish List

Qty

$ 6.99 USD

Add to Wish List

If your turbo oil drain line connection is leaking, this gasket is likely the culprit. Replace your old gasket with this brand new gasket from Elring to eliminate oil leaks, prevent oil loss, and keep both your engine and driveway clean.

Show More Show Less

Select Vehicle

Purpose

Category

Turbos

Brand

View All Brands

Price

Special Offers

Shipping