BMW Fuel System Parts for BMW 1 Series E82 (2008-2013)

ARC Upgraded Fuel Pump Control Module - Dual Ball Bearing Fan - EKPM3...

T#:28304525

Part#: EKP-HW05-E-SF

In Stock

$ 199.99 USD

Add to Wish List

Qty

$ 199.99 USD

Add to Wish List

Arc Terminator now offers upgraded EKMP3 Fuel Pump Control Modules featuring a 22 Amp INCREASE in maximum current capacity over an OEM EKPM3. This allows for more current to be supplied to your low-pressure fuel pump (LPFP) without risking thermal overload, which often leads to your car shutting down. This means that you won't have to worry about being stranded on the side of the road while waiting for your EKP module to cool down, especially when you've installed a large low-pressure fuel pump such as a Walbro 525lph. How does the integrated automatic cooling work? The integrated automatic cooling works by us installing a thermal activation switch directly onto the new half bridge IC. When the half bridge IC reaches 50°C, the 40mm fan will turn on and keep running until the IC is below 50°C or until the EKMP3 stops receiving power. I have an EKPM2, can I upgrade to this? Yes. You can upgrade to this. We recommend using the HW05 and below module. You will need to code it in order for it to function properly. Can I run more than 1 low-pressure fuel pump off of this module? No. We do not recommend that you use more than one low-pressure fuel pump with any EKP module due to the factory wiring supplying power to the EKP Module is only 12 gauge, which is not rated for the type of power demands that two low-pressure fuel pumps would require.

Show More Show Less

BMW B46 B48 B58 Motiv ReFlex 0-10 Bar Pressure Sensor

T#:28537533

Part#: 101-0216

In Stock

$ 105.00 USD

Add to Wish List

Qty

$ 105.00 USD

Add to Wish List

BMW B46 B48 B58 Motiv ReFlex 0-10 Bar Pressure Sensor is designed for accurate measurement of fluid and air pressure in high-performance applications. Ideal for monitoring a variety of pressures including fuel, boost, coolant, and oil, this sensor provides crucial data for optimizing vehicle performance.

Featuring a 2-Pin DTM connector, this sensor offers a direct plug-and-play connection to the ReFlex+ harness, ensuring a seamless integration with flash platforms via CANbus. Each ReFlex+ unit can support up to two of these sensors, allowing for comprehensive monitoring.

Versatile Measurement: Capable of measuring fuel pressure, boost, coolant, oil, and other fluids.
Easy Integration: 2-Pin DTM connector provides a direct plug-and-play connection.
Comprehensive Monitoring: Supports integration of up to two sensors per ReFlex+ unit.
High-Performance Design: Designed to handle high pressures and deliver accurate readings.

For optimal installation, consider using the 3/8 Female to 3/8 Male SAE Quick Disconnect Adapter with a 1/8" NPT port on an ethanol sensor or the 5/16 Female to 5/16 Male SAE Quick Disconnect Adapter with a 1/8" NPT port on a factory fuel line. Please note that the ethanol sensor is not included.

Show More Show Less

BMW B46 B48 Motiv ReFlex Plug-n-Play Ethanol Sensor Harness

For Vehicles With Motiv ReFlex Unit Currently Installed Only

T#:22723690

Part#: 101-0212

In Stock

$ 49.00 USD

Add to Wish List

Qty

$ 49.00 USD

Add to Wish List

BMW B46 B48 Motiv ReFlex Plug-n-Play Ethanol Sensor Harness simplifies the integration of an ethanol content sensor into your BMW's Re|Flex system. This harness is designed to enhance your vehicle's performance by scaling the sequential port injection based on real-time ethanol content, eliminating the need for manual adjustments. Key benefits include:

Effortless Installation: Plug-n-play design makes it easy to connect an ethanol content sensor without extensive modifications.
Real-Time Adjustments: Allows for automatic scaling of port injection based on real-time ethanol content, optimizing engine performance.
Seamless Integration: For CANbus integrated vehicles, it facilitates integration with the factory DME/ECU (pending feature release by tuning platforms).
No Manual Flashes Required: Removes the need for ground disconnection or map switching on your port injection controller.

Please note that the ethanol sensor is not included with this harness.

Show More Show Less

BMW B58 3.0L ReFlex+ Main Injector Harness - Inline-6

T#:29201081

Part#: 900.1008

In Stock

$ 200.00 USD

Add to Wish List

Qty

$ 200.00 USD

Add to Wish List

BMW B58 3.0L ReFlex+ Main Injector Harness - Inline-6 offers a seamless integration solution for your turbocharged BMW inline-6 engine. Designed to work with the Motive ReFlex Control Unit, this plug-n-play harness ensures a hassle-free installation process for your 6 EV6/USCAR injectors.

Direct Plug-N-Play Installation: Connects directly to the ReFlex+ Control Unit and your EV6/USCAR injectors.
Versatile Connector Options: Includes DTM 3-Pin and 2-Pin connectors for integration with ethanol content sensors and external sensors.
Multiple Sensor Connectors: Features connections for a 0-10 Bar Pressure Sensor and a 0-5v sensor.
Auxiliary Output Wires: Provides 3x unterminated wires for additional low-side triggers from the ReFlex+ Control Unit.
Easy Connection: DTM 8-Pin connector allows for straightforward setup with ReFlex+ Install Harnesses.

Turner Motorsport's harness ensures efficient and reliable performance, streamlining the process of integrating your ReFlex+ Control Unit with your BMW B58 engine.

Show More Show Less

BLACKLINE Performance Fuel Cap Cover

For Model Years 2010 or Newer

T#:797049

Part#: FXXFCC

Ships in 4 Business Days

$ 47.00 USD

Add to Wish List

Qty

$ 47.00 USD

Add to Wish List

Give your gas cap a much-needed upgrade with the all new BMW M Car Series Billet Aluminum Fuel Cap Cover from Goldenwrench Supply Co. This performance Fuel Cap Cover Kit comes with a Billet Aluminum Fuel Cap Cover, and Installation Instructions. Please note this a cover that affixes on top of your factory fuel cap installing easily in minutes.

Show More Show Less

BLACKLINE Performance Fuel Cap Cover - Motorsport Blue

Fits 2010+ Model Year BMWs only!

T#:6635763

Part#: FXXFCC-B

In Stock

$ 47.00 USD

Add to Wish List

Qty

$ 47.00 USD

Add to Wish List

Give your gas cap a much-needed upgrade with the all new BMW M Car Series Billet Aluminum Fuel Cap Cover from Goldenwrench Supply Co. This performance Fuel Cap Cover Kit comes with a Billet Aluminum Fuel Cap Cover, and Installation Instructions. Please note this a cover that affixes on top of your factory fuel cap installing easily in minutes.

Show More Show Less

3/8" Quick Disconnect Adapter With 1/8" NPT Port

T#:29500156

Part#: 200.1105

In Stock

$ 24.00 USD

Add to Wish List

Qty

$ 24.00 USD

Add to Wish List

Quick disconnect adapters (QDA) are commonly used to adapt different components into vehicle fuel systems without requiring permanent modification. These adaptersÂ are machined from high-grade aluminum and anodized for corrosion resistance. QDAs incorporate VitonÂ© o-rings which are compatible with most types of fuel, solvents and oils. QDAs maintain a reliable leak-proof seal under normal fuel injection system operating pressures. This particular QDA is sized perfectly to adapt right between the fuel line you were going to connect to your ethanol sensor. 3/8" (9.5mm) female quick disconnect 3/8" (9.5mm) male quick disconnect 1/8" Female pipe thread port * Viton© o-rings Crecent-lock system E-85 compatible Black anodized aluminum

Show More Show Less

ReFlex+ Install Harness - Flying Lead

T#:29201083

Part#: 900.1016

In Stock

$ 95.00 USD

Add to Wish List

Qty

$ 95.00 USD

Add to Wish List

A flying lead harness is a wiring harness that is unterminated at one end and has an excess length of wire so that installation can be customized by the end user. That makes this section of the ReFlex+ Install Harness truly universal. On one end, this harness has an 8-pin connector to plug into any one of our ReFlex+ Main Injector Harnesses. The other end of each wire is unterminated and will be connected to the appropriate sensor, ground, or power supply based on installation instructions. Each harness has a wire for: Switched +12v Input w/ inline fuse +5v Input Ground Can HI Can Lo Cam Sensor Signal Crank Sensor Signal Map Sensor Signal

Show More Show Less

VTT N54 Vacuum Pump Block Off Plate

2X Entries Into Our F80 M3 Sweepstakes

T#:11497328

Part#: VTT-N54-VACUUM-B

Ships in 10 Business Days

Sale - Save 15% $ 127.99

This product was last offered at the strikethrough price on
09-03-2026

$ 108.37 USD

Add to Wish List

Qty

Sale - Save 15%

$ 127.99

This product was last offered at the strikethrough price on
09-03-2026

$ 108.37 USD

Add to Wish List

Looking to remove the HPFP or DI system on your N54? this plate will block the vacuum pump and prevent oil leaks. You will need to remove any fuel lines, etc. Kit includes Block Plate Note – Plates may come in a clear or anodize black finish depending on stock on hand

Show More Show Less

VTT BMW N54 “DI Injector” Delete Kit

2X Entries Into Our F80 M3 Sweepstakes

T#:11497326

Part#: VTT-N54-DI-DELET

Ships in 1 Business Day

Sale - Save 15% $ 339.99

This product was last offered at the strikethrough price on
09-03-2026

$ 288.99 USD

Add to Wish List

Qty

Sale - Save 15%

$ 339.99

This product was last offered at the strikethrough price on
09-03-2026

$ 288.99 USD

Add to Wish List

Looking to get rid of the troublesome and expensive DI injectors on your BMW N54 and move to PI only and a standalone? If so VTT has you covered with its new N54 PI delete kit. This kit allows you to SAFELY remove the DI injectors, install our delete fittings, and run PI only. We machined these deletes from 310 Stainless for extreme heat, and corrosion resistance, and include 3 hold downs. These DI deletes COMPLETELY get rid of all factory provisions, including the seal. If the seal is left intact with no fuel to cool the injector or delete it will quickly overheat and melt the delicate seal causing combustion gasses to escape the engine creating misfires, and worse possibly damaging your injector bore on the cylinder head. Our deletes are machined to be a press fit into the cylinder, and can be either cooled with liquid nitrogen, and dropped in, or tapped in with a hammer, and then held down with the included hold downs. We also include M6 tapped holes on the top of each one in case they need to be removed you can attach a slide hammer, and remove the delete. These are sold as a kit and come with the following 6 – 310 Stainless DI Delete fittings 3 – Hold down brackets Completetion of this kit will require the purchase of HPFP delete plate - ES# 4623950 PLEASE NOTE: THIS KIT REQUIRES EXTENSIVE MODIFICATIONS TO CONVERT YOUR ENGINE TO PI ONLY. THIS INCLUDES BUT IS NOT LIMITED TO A FULL PORT INJECTION SOLUTION, AND STAND-ALONE TO RUN THE PI SYSTEM. WE RECOMMEND THIS PNP SYSTEM USING THE MAXX ECU IT PROVIDES ALL YOU NEED TO GET UP AND RUNNING WITH PI ONLY ON THE TUNING SIDE OF THINGS – https://www.pnpecu.com/pnpecu-maxxecu-n54-pnp-kit-437-p.asp

Show More Show Less

Upgraded EKPM3 Fuel Pump Control Module - Noctua Fan

T#:28304530

Part#: EKP-HW05-E-NF

In Stock

$ 229.99 USD

Add to Wish List

Qty

$ 229.99 USD

Add to Wish List

Arc Terminator now offers upgraded EKMP3 Fuel Pump Control Modules featuring a 22 Amp INCREASE in maximum current capacity over an OEM EKPM3. This allows for more current to be supplied to your low-pressure fuel pump (LPFP) without risking thermal overload, which often leads to your car shutting down. This means that you won't have to worry about being stranded on the side of the road while waiting for your EKP module to cool down, especially when you've installed a large low-pressure fuel pump such as a Walbro 525lph. Includes 40mm Noctua Silent Fan! How does the integrated automatic cooling work? The integrated automatic cooling works by us installing a thermal activation switch directly onto the new half bridge IC. When the half bridge IC reaches 50°C, the 40mm fan will turn on and keep running until the IC is below 50°C or until the EKMP3 stops receiving power. I have an EKPM2, can I upgrade to this? Yes. You can upgrade to this. We recommend using the HW05 and below module. You will need to code it in order for it to function properly. Can I run more than 1 low-pressure fuel pump off of this module? No. We do not recommend that you use more than one low-pressure fuel pump with any EKP module due to the factory wiring supplying power to the EKP Module is only 12 gauge, which is not rated for the type of power demands that two low-pressure fuel pumps would require.

Show More Show Less

E82 Silent Fan EKP PNP Cooler Kit - 40mm Noctua Fan

A Must For Cars With Upgraded LPFPs

T#:26471523

Part#: SILENT-E82-EKP

Ships in 1 Business Day

Starting at $ 59.99 USD

Add to Wish List

Starting at $ 59.99 USD

Add to Wish List

The full plug-and-play EKPM3 / EKPM2 cooler kit is designed specifically for E82 BMWs using an EKPM3 or EKPM2 fuel pump control module. This is recommended for anyone using a low-pressure fuel pump that is larger than the OEM fuel pump. Please note that if you have an HW06 + (Slim EKPM3), you must choose the HW06 option, as the pre-HW06 housings will not fit. Installation Tips: https://arcterminator.com/pages/e90-e92-e93-ekp-cooler-install-instructions We recommend using Fuse #8 (2007+ E82), which is the cigarette lighter fuse to power this. It is a 20 amp fuse, which you will just need to pull out and put into the empty slot of the fuse holder that comes with the kit. Then you'll need to put that fuse holder into the now empty #8 fuse slot. This ensures that the fan will only turn on when the ignition in the car is turned on. You'll also need trim removal tools, as well as a 10mm socket to remove and re-install the EKP module. We recommend using the stock grounding point that's above the EKP module or the EKP module's mounting points as the ground. The ring terminal with the kit will fit either location. The whole installation should take you between 30 - 45 minutes. The cooler housing is designed to fit over the EKP module just like the OEM housing and fits with plenty of room in the stock EKP location. The full kit is printed and assembled in the U.S.A. by Arc Terminator LLC. Full Kit Contents: 1x PNP EKPM3 / EKPM2 Cooler Housing With a Genuine 60mm Noctua Fan 1x 14x14x6mm Heatsink With Thermal Tape 1x 14x9x5mm Heatsink With Thermal Tape 1x 9x9x5mm Heatsink With Thermal Tape (EKPM3 Kit) 2x 9x9x5mm Heatsink With Thermal Tape (EKPM2 Kit) 8x 4" Zip Ties 1x Alcohol Wipe 1x 2 Amp Mini Blade Fuse Why this kit exists: The EKPM3 and EKPM2 have been shown to overheat and cause vehicle shutdown issues when larger fuel pumps that draw more current than OEM are used. This shutdown comes from critical components on the EKPM3 and EKPM2 overheating when larger current draws are coming from the fuel pump. The PNP kit comes with heatsinks for the most heat-sensitive and heat-producing components in the EKPM3 / EKPM2 to further increase cooling effectiveness. When paired with a silent Noctua fan that directs a large amount of airflow through the cooler housing, the EKPM3 / EKPM2 stays significantly cooler, which prolongs the life of the module. We also recommend anyone using a larger fuel pump than OEM to properly code their EKP module with Pro-Tool's built-in "Voltage Fix" feature.

Show More Show Less

E82 / E88 EKPM2 EKPM3 PNP Cooler Kit - (1 Series)

A Must For Cars With Upgraded LPFPs

T#:26404802

Part#: E82-EKP-PNPC

Ships in 1 Business Day

Starting at $ 44.99 USD

Add to Wish List

Starting at $ 44.99 USD

Add to Wish List

The full plug-and-play EKPM3 / EKPM2 cooler kit is designed specifically for E82 BMWs using an EKPM3 or EKPM2 fuel pump control module. This is recommended for anyone using a low-pressure fuel pump that is larger than the OEM fuel pump. Please note that if you have an HW06 + (Slim EKPM3), you must choose the HW06 option, as the pre-HW06 housings will not fit. 10% of all proceeds from pink housings sold will be donated towards Breast Cancer research. Installation Tips: https://arcterminator.com/pages/e90-e92-e93-ekp-cooler-install-instructions We recommend using Fuse #8 (2007+ E82), which is the cigarette lighter fuse to power this. It is a 20 amp fuse, which you will just need to pull out and put into the empty slot of the fuse holder that comes with the kit. Then you'll need to put that fuse holder into the now empty #8 fuse slot. This ensures that the fan will only turn on when the ignition in the car is turned on. You'll also need trim removal tools, as well as a 10mm socket to remove and re-install the EKP module. We recommend using the stock grounding point that's above the EKP module or the EKP module's mounting points as the ground. The ring terminal with the kit will fit either location. The whole installation should take you between 30 - 45 minutes. We also offer a DIY kit that includes everything you'll need to create your own active cooling solution here: https://arcterminator.com/products/ekp-active-cooling-diy-kit The cooler housing is designed to fit over the EKP module just like the OEM housing and fits with plenty of room in the stock EKP location. The housing is 3D printed using durable ASA, ABS or PETG, depending on the color choice. The full kit is printed and assembled in the U.S.A. by Arc Terminator LLC. Full Kit Contents: 1x PNP EKPM3 / EKPM2 Cooler Housing With 5015 Fan 1x 14x14x6mm Heatsink With Thermal Tape 1x 14x9x5mm Heatsink With Thermal Tape 1x 9x9x5mm Heatsink With Thermal Tape (EKPM3 Kit) 2x 9x9x5mm Heatsink With Thermal Tape (EKPM2 Kit) 8x 4" Zip Ties 1x Alcohol Wipe 1x 2 Amp Mini Blade Fuse Why this kit exists: The EKPM3 and EKPM2 have been shown to overheat and cause vehicle shutdown issues when larger fuel pumps that draw more current than OEM are used. This shutdown comes from critical components on the EKPM3 and EKPM2 overheating when larger current draws are coming from the fuel pump. The PNP kit comes with heatsinks for the most heat-sensitive and heat-producing components in the EKPM3 / EKPM2 to further increase cooling effectiveness. When paired with a potent 5015 blower fan that directs a large amount of airflow through the cooler housing, the EKPM3 / EKPM2 stays significantly cooler, which prolongs the life of the module. We also recommend anyone using a larger fuel pump than OEM to properly code their EKP module with Pro-Tool's built-in "Voltage Fix" feature.

Show More Show Less

BMW Fuel Line Upgrade - Short Line Kit

T#:29267521

Part#: 900.1025

In Stock

$ 150.00 USD

Add to Wish List

Qty

$ 150.00 USD

Add to Wish List

Factory fuel lines are often not designed or safe for use with ethanol based fuels. Our PTFE fuel lines are the perfect solution for installing into your vehicle without having to permanently modify your vehicle's fuel lines. Simply uninstall the factory line and install our pre-measured lines that come setup with the correct fittings for a plug-n-play install in your vehicle. Please Note: This does NOT include an ethanol Content Sensor.

Show More Show Less

E9X/E8X Bucketed Fuel Pump Upgrade - Single Shot

T#:590135

Part#: E90BUCKETSTKSS

Ships in 10 Business Days

$ 551.99 USD

Add to Wish List

Qty

$ 551.99 USD

Add to Wish List

Multi-Pump Fuel Surge Tank (MPFST)

T#:31059457

Part#: 20-1440

In Stock

$ 549.99 USD

Add to Wish List

Qty

$ 549.99 USD

Add to Wish List

N54 Dual Bucketless Fuel Pump Upgrade - "External Series"

T#:590122

Part#: PFS-E9X-BCKTLSSE

Back Ordered

$ 609.99 USD

Add to Wish List

Qty

$ 609.99 USD

Add to Wish List

Looking to make 700WHP+ on your N54 powered vehicle, need the fuel to do to so, and don’t want to spend a ton of money? Look no further than the PFS bucketless fuel “External Series” pump upgrade! The external series takes our already best on the market bucketless design and adds a 3/8 Quick Disconnect bulkhead fitting to the top hat which allows you to run the secondary pump independent of the factory lines. This allows FULL FLOW from the second pump unhindered by the factory jet pump, siphon, fuel filter, or Fuel pressure regulator. All PFS “External Series” Bucketless pumps include the following: A complete plug and play solution by simply getting rid of your factory bucket Two New E85 compatible Walbro 450 F9000274 pumps Two new Walbro filters (Hydra-Mat available in options) Wiring Harness for the secondary pump with Fused power Hobbs Switch Fuel pump relay 3/8 QD fitting on the Passenger side top hat -6 Fuel line from Passenger side tank to the front of the vehicle -6 Fuel line from Driver side tank to the front of the vehicle PFS 10 micron filter with choice of outlet fittings Flow testing on the PFS test bench prior to shipping

Show More Show Less

Radium - Split-Flow Flex Fuel Sensor Adapter

T#:53290958

Part#: 20-0589

In Stock at Vendor

$ 99.99 USD

Add to Wish List

Qty

$ 99.99 USD

Add to Wish List

Vargas Shotgun Single Barrel - MT - BMW E9X, E8X N54

For vehicles with Manual Transmission only

2X Entries Into Our F80 M3 Sweepstakes

T#:52305464

Part#: STGN-SB-1-N54-MT

Ships in 10 Business Days

Sale - Save 15% $ 939.99

This product was last offered at the strikethrough price on
09-03-2026

$ 798.99 USD

Add to Wish List

Qty

Sale - Save 15%

$ 939.99

This product was last offered at the strikethrough price on
09-03-2026

$ 798.99 USD

Add to Wish List

The VTT Single Barrel for Manual Transmissions is the "Stage 1" of the Shotgun family, providing a massive headroom increase over the stock setup.

Vargas Planetary OverDrive HPFP Upgrade - BMW N54

T#:51778140

Part#: PFS-POD-HPFP-UPG

Ships in 10 Business Days

$ 1,154.99 USD

Add to Wish List

Qty

$ 1,154.99 USD

Add to Wish List

This Planetary OverDrive system allows you to stick with your factory BMW high-pressure fuel pump while unlocking the flow needed for big-turbo builds.

E9X/E8X Bucketed Fuel Pump Upgrade - Double Shot

T#:590134

Part#: E90BUCKETSTKDS

Back Ordered

$ 699.00 USD

Add to Wish List

Qty

$ 699.00 USD

Add to Wish List

Project Cars

SELECT YOUR BMW

BMW Fuel System Parts for BMW 1 Series E82 (2008-2013)

Sub-Categories

ARC Upgraded Fuel Pump Control Module - Dual Ball Bearing Fan - EKPM3...

BMW B46 B48 B58 Motiv ReFlex 0-10 Bar Pressure Sensor

BMW B46 B48 Motiv ReFlex Plug-n-Play Ethanol Sensor Harness

BMW B58 3.0L ReFlex+ Main Injector Harness - Inline-6

BLACKLINE Performance Fuel Cap Cover

BLACKLINE Performance Fuel Cap Cover - Motorsport Blue

3/8" Quick Disconnect Adapter With 1/8" NPT Port

ReFlex+ Install Harness - Flying Lead

VTT N54 Vacuum Pump Block Off Plate

VTT BMW N54 “DI Injector” Delete Kit

Upgraded EKPM3 Fuel Pump Control Module - Noctua Fan

E82 Silent Fan EKP PNP Cooler Kit - 40mm Noctua Fan

E82 / E88 EKPM2 EKPM3 PNP Cooler Kit - (1 Series)

BMW Fuel Line Upgrade - Short Line Kit

E9X/E8X Bucketed Fuel Pump Upgrade - Single Shot

Multi-Pump Fuel Surge Tank (MPFST)

N54 Dual Bucketless Fuel Pump Upgrade - "External Series"

Radium - Split-Flow Flex Fuel Sensor Adapter

Vargas Shotgun Single Barrel - MT - BMW E9X, E8X N54

Vargas Planetary OverDrive HPFP Upgrade - BMW N54

E9X/E8X Bucketed Fuel Pump Upgrade - Double Shot

Select Vehicle

Purpose

Category

Brand

Price

Special Offers

Shipping

Narrow Results