Please ensure your correct model is selected
This product was last offered at the strikethrough price on
06-13-2026
This product was last offered at the strikethrough price on
06-13-2026
The rear lower control arms on E82/E9X models are the weakest link in the rear suspension. The arm is made from folded sheetmetal and it bends and deforms easily. Not only will it deform from potholes and curbs, tow truck drivers love to hook onto them without realizing how weak they are. We have seen other race teams complete the box section to make them stronger. A bent arm will throw off the geometry in the suspension, potentially affecting handling and tire wear. These aluminum arms are both lighter and stronger than the factory sheetmetal arms and is the best solution for chronic bending of the stock arm. These are a direct replacement to your stock arms with no changes needed to your alignment. New high-grade hardware is included.
Note: the stock arm is designed from the factory to be intentionally weak. These arms will bend so that something else in the suspension does not break. Our race cars used the stock sheetmetal arm but we replaced them often. We found that it was better to finish a race with a bent arm than not finish due to a catastrophic failure. The ECS arms are still designed to be the weakest link but are far stronger than the factory arm and will not bend as easily.
This item fits the following BMWs:
2008-2013 E82 E88 BMW 128i 135i 1M Coupe
2006-2011 E90 BMW 325i 325xi 328i 328xi 330i 330xi 335i 335xi M3 - Sedan
2007-2011 E91 BMW 325i 325xi 328i 328xi - Touring Wagon
2007-2013 E92 BMW 328i 328xi 335i 335is 335xi M3 - Coupe
2007-2013 E93 BMW 328i 335i 335is M3 - Convertible
When an E9X is lowered beyond the limits of just lowering springs, the rear wheels toe-in excessively. This excessive rear toe leads to premature wear, that many people attribute to an increase in negative camber. It has become a common belief that an extremely low vehicle will wear the tires wrong as a matter of consequence. It has become standard practice to go as low as you can and proceed to replace your tires every five to ten thousand miles. Whats more is that when the vehicle reaches a certain ride height, the factory arms become maxed out and there is no way to compensate and dial in the proper toe. You're left with an improperly aligned vehicle that is in effect worse off than it was with the stock suspension installed.
This is not only uneconomical but improper and unsafe. ECS Tuning is proud to offer a solution for this problem in the form of Rogue Engineering E9X adjustable rear toe arms. These arms allow for greater toe adjustment on vehicles that have been lowered with a coilover suspension. With the toe set properly the tires can contact the road properly this maximizes grip and minimizes wear.
Features:
BMW E9X M3/E82 1M Inner Lower Tension Arm Bearing is engineered to elevate suspension performance with precision and durability. Developed by Fall-Line, known for their championship-level race cars and premium suspension components, this bearing is a significant upgrade over factory rubber bushings. Designed for motorsport applications, it incorporates FK spherical bearings for enhanced strength and longevity.
Updated design! Now shipping!
When an E9X is lowered beyond the limits of just lowering springs, the rear wheels toe-in excessively. This excessive rear toe leads to premature wear, that many people attribute to an increase in negative camber. It has become a common belief that an extremely low vehicle will wear the tires wrong as a matter of consequence. It has become standard practice to go as low as you can and proceed to replace your tires every five to ten thousand miles. Whats more is that when the vehicle reaches a certain ride height, the factory arms become maxed out and there is no way to compensate and dial in the proper toe. You're left with an improperly aligned vehicle that is in effect worse off than it was with the stock suspension installed.
This is not only uneconomical but improper and unsafe. ECS Tuning is proud to offer a solution for this problem in the form of Rogue Engineering E9X adjustable rear toe arms. These arms allow for greater toe adjustment on vehicles that have been lowered with a coilover suspension. With the toe set properly the tires can contact the road properly this maximizes grip and minimizes wear.
Features:
100% machined and anodized, 6061-T6 lightweight aluminum arms (and collars).
Stainless hardware and spacers are perfect for the tough Northeast climate!
New! Easy adjustment with 22mm open ended wrench and 5mm allen key! It only requires 15 ft. lbs. on the clamp to secure the clamp!
New! Included lock-out kit, replaces factory eccentric hardware.
Updated 3-piece rod ends features 4130 chromoly steel bodies, heat-treated, alloy steel races, and Teflon liners
Extremely easy installation and adjustment (your alignment shop will LOVE you!)
This product was last offered at the strikethrough price on
08-31-2026
Rogue Engineering E82/E9X Adjustable Rear Camber Link Set V2.0 is the ultimate upgrade for BMW enthusiasts seeking enhanced handling, improved tire wear, and precise suspension tuning. This high-performance solution is engineered to fit BMW E82 1-Series and E9X 3-Series models, offering superior adjustability and durability over OEM components. Ideal for street and track use, this camber link set is crafted from premium materials to ensure strength and long-lasting performance.
Key Features:
These replace the wishbone and guide arm links in the factory suspension which have rubber bushings and limited adjustment. Enhanced suspension adjustability for optimized alignment Improves handling and reduces uneven tire wear Compatible with BMW E82 1-Series and E9X 3-Series models Constructed from high-strength materials for durability and reliability Perfect for both street performance and track applications Turner Motorsport proudly offers the Rogue Engineering E82/E9X Adjustable Rear Camber Link Set V2.0, providing BMW drivers with unmatched performance and precision.
