BMW Intake Parts for BMW 1 Series E82 (2008-2013)

BMS Replacement DCI Filters - Red

T#:38890884

Part#: BMS-N54-DCIR-R

Back Ordered

$ 79.00 USD

Add to Wish List

Qty

$ 79.00 USD

Add to Wish List

High-performance replacement filters for the N54 BMW Dual Cone Intake (DCI), featuring an integrated velocity stack for optimal airflow. Pre-oiled with red filter oil and includes new clamps for hassle-free installation.

Show More Show Less

Burger Motorsport 4 BAR TMAP Sensor & Adapter - BMW N55/N54/S55 (2007...

T#:34885402

Part#: 4BAR TMAP

Back Ordered

$ 139.99 USD

Add to Wish List

Qty

$ 139.99 USD

Add to Wish List

Use these plug and play adapters to quickly adapt a 4bar TMAP sensor to your N54/N55/S55 BMW, raising the boost maximum boost range from 20psi factory up to 43psi.

BMS Replacement DCI Filters - Blue

T#:38890886

Part#: BMS-N54-DCIR-B

In Stock

$ 89.00 USD

Add to Wish List

Qty

$ 89.00 USD

Add to Wish List

High-performance replacement filters for the N54 BMW Dual Cone Intake (DCI), featuring an integrated velocity stack for optimal airflow. Pre-oiled with red filter oil and includes new clamps for hassle-free installation.

Show More Show Less

Burger Motorsports Upgraded Intake Coupler - N55 BMW

Not for sale or use in the state of California.

T#:556785

Part#: BMS-E-N55-INT-C

In Stock

$ 24.00 USD

Add to Wish List

Qty

$ 24.00 USD

Add to Wish List

When upgrading your intake, such as with the Burger Motorsports Performance Intake, your coupler is only good for stock vehicles. At boost pressure higher than stock, the stock accordion coupler is likely to collapse, suffocating your engine from air flow and potentially causing it to stall. With this 5 layer silicon upgraded coupler from Burger Motorsports, you can run your car as hard as possible even with upgraded turbos or port injection and will never have to worry about the coupler collapsing.

Show More Show Less

Replacement N55 Performance Filter - Red

T#:38890883

Part#: BMSREPAFNFFR

In Stock

$ 70.00 USD

Add to Wish List

Qty

$ 70.00 USD

Add to Wish List

Enhance your BMW's performance with the Replacement N55 Performance Filter from Burger Motorsport. Specifically designed for N55 engines, this filter optimizes airflow, leading to increased horsepower and torque. Enjoy improved throttle response and fuel efficiency, all while protecting your engine from harmful contaminants. Key Features: Designed for N55 engines Optimizes airflow for increased power Improves throttle response and fuel efficiency Protects engine from contaminants

Show More Show Less

Intake Manifold Upgrade Kit

10X Entries Into Our F80 M3 Sweepstakes

T#:15710827

Part#: 11617559523-KT

In Stock

Sale - Save 25% $ 902.99

This product was last offered at the strikethrough price on
05-03-2026

$ 677.38 USD

Add to Wish List

Qty

Sale - Save 25%

$ 902.99

This product was last offered at the strikethrough price on
05-03-2026

$ 677.38 USD

Add to Wish List

The E90 330i had the highest horsepower out of the N52-powered vehicles. The reason for this was while the 128i, 325i, 328i, 525i, and 528i received a single-stage manifold, the 330i was gifted a 3-stage manifold. A 3-stage manifold consisted of 2 DISA valves that would divert air to the cylinders that needed it. With more air going to the appropriate cylinders and fuel adjustments by the ECU, this valve system helps extract the most power from the N52. Luckily this amazing manifold bolts on to any version of the N52 and, after a flash of the ECU, can give you up to 42hp! *Flash Software not currently available from ECS Tuning* Kit includes: 330i intake manifold Both DISA valves Gaskets Mounting hardware Crankcase vent hose

Show More Show Less

Turbosmart Raceport Gen-V Universal - Black (No Weld Flange) Female (...

T#:8076768

Part#: TS-0204-1142

In Stock

$ 324.99

This product was last offered at the strikethrough price on
08-10-2026

$ 289.99 USD

Limited Qty Sale

Add to Wish List

Qty

$ 324.99

This product was last offered at the strikethrough price on
08-10-2026

$ 289.99 USD

Limited Qty Sale

Add to Wish List

Turbosmart GenV Raceport BOV (Fits competitors 50mm / female style flange. No weld flange included) The Race Port is famous for being an amazingly small and light BOV for turbocharged competition level engines. Featuring our unique collar design and internal flow structures, it is 50% lighter and 25% smaller than the competition while flowing 330 CFM – making it the highest flowing BOV of its type on the market. Fits Chargepipes With Tial/Turbosmart Flange

Show More Show Less

TurboSmart GenV RacePort Blow-Off Valve - Blue

T#:27372078

Part#: TS-0204-1141

In Stock

$ 324.99 USD

Add to Wish List

Qty

$ 324.99 USD

Add to Wish List

Turbosmart GenV Raceport BOV (Fits competitors 50mm / female style flange. No weld flange included)

The Race Port is renowned for its exceptional compactness and lightweight design tailored for turbocharged competition-level engines. With its innovative collar design and internal flow structures, this BOV stands out as 50% lighter and 25% smaller than competing models, yet it boasts an impressive flow rate of 330 CFM, making it the market's top-performing BOV in its category.

Fits Chargepipes With Tial/Turbosmart Flange

Show More Show Less

TurboSmart GenV RacePort Blow-Off Valve - Red - Female Flange ...

T#:27372080

Part#: TS-0204-1144

In Stock

$ 324.99

This product was last offered at the strikethrough price on
08-11-2026

$ 289.99 USD

Limited Qty Sale

Add to Wish List

Qty

$ 324.99

This product was last offered at the strikethrough price on
08-11-2026

$ 289.99 USD

Limited Qty Sale

Add to Wish List

Turbosmart GenV Raceport BOV (Fits competitors 50mm / female style flange. No weld flange included)

The Race Port is renowned for its exceptional compactness and lightweight design tailored for turbocharged competition-level engines. With its innovative collar design and internal flow structures, this BOV stands out as 50% lighter and 25% smaller than competing models, yet it boasts an impressive flow rate of 330 CFM, making it the market's top-performing BOV in its category.

Fits Chargepipes With Tial/Turbosmart Flange

Show More Show Less

TurboSmart GenV RacePort Blow-Off Valve - Purple - Female Flange ...

T#:27372081

Part#: TS-0204-1143

In Stock at Vendor

$ 324.99 USD

Add to Wish List

Qty

$ 324.99 USD

Add to Wish List

Turbosmart GenV Raceport BOV (Fits competitors 50mm / female style flange. No weld flange included)

The Race Port is renowned for its exceptional compactness and lightweight design tailored for turbocharged competition-level engines. With its innovative collar design and internal flow structures, this BOV stands out as 50% lighter and 25% smaller than competing models, yet it boasts an impressive flow rate of 330 CFM, making it the market's top-performing BOV in its category.

Fits Chargepipes With Tial/Turbosmart Flange

Show More Show Less

BMS High Flow Silicone Inlets - 2" Opening For Hybrid Turbos - BMW N5...

T#:14684349

Part#: N54HFSILINLETS

Ships on Sep 21, 2026

$ 229.00 USD

Add to Wish List

Qty

$ 229.00 USD

Add to Wish List

These high-quality BMS N54 silicone inlets replace your flimsy and restrictive plastic N54 BMW inlets reducing restriction and dramatically improving airflow, top-end boost, and performance. Includes all required hardware and is compatible with both factory-style diverter valves and blow-off valve kits. Available in 1.75" inlets for factory turbos or 2" inlets for hybrid and aftermarket turbos. Compatible with BMS DCI and all other N54 intake systems. FEATURES AND BENEFITS Huge 30-50whp top-end power gains Replaces your restrictive factory intake system Retains OEM engine bay look Durable high-temperature reinforced silicone for long life Compatible with both RHD and LHD vehicles Includes required hardware

Show More Show Less

Burger Motorsports 2007-2012 TypeA 4BAR Adapter - E82/88 E9X E6X N54 ...

T#:599636

Part#: TYPEA4BARADAPTER

Ships in 2 Business Days

$ 35.00 USD

Add to Wish List

Qty

$ 35.00 USD

Add to Wish List

Use these plug and play adapters to quickly adapt a 4bar TMAP sensor to your N54/N55/S55 BMW, raising the boost maximum boost range from 20psi factory up to 43psi. For very high boost applications, this 4 BAR adapter can be used which requires Bosch 4 BAR sensor (Part # 281002576). SENSOR NOT INCLUDED, Please see T#587716

Show More Show Less

BMS Replacement DCI Filters - White

T#:38890885

Part#: BMS-N54-DCIR-W

Ships on Sep 21, 2026

$ 84.00 USD

Add to Wish List

Qty

$ 84.00 USD

Add to Wish List

High-performance replacement filters for the N54 BMW Dual Cone Intake (DCI), featuring an integrated velocity stack for optimal airflow. Pre-oiled with red filter oil and includes new clamps for hassle-free installation.

Show More Show Less

Replacement Intake Coupler - Priced Each

Not for sale or use in the state of California.

T#:583384

Part#: INTAKECOUPLER

In Stock

$ 15.00 USD

Add to Wish List

Qty

$ 15.00 USD

Add to Wish List

BMW N54 BOV Vaccuum Adapter

T#:589530

Part#: N54BOVVACADPT

Ships on Sep 21, 2026

$ 59.00 USD

Add to Wish List

Qty

$ 59.00 USD

Add to Wish List

BMS Replacement Intercooler For E Chassis BMW

07'-13' Model years

T#:38621402

Part#: BMS-INTCLR-N5455

Ships on Sep 21, 2026

$ 329.00 USD

Add to Wish List

Qty

$ 329.00 USD

Add to Wish List

The BMS N54/N55 Replacement E-Chassis Intercooler Upgrade for BMW improves cooling efficiency, boosts wheel horsepower, and maintains performance during extended driving sessions. With a larger core and expanded surface area compared to the stock intercooler, it reduces pressure drop and significantly enhances cooling capacity. Expect peak gains of around 10whp, with sustained increases of 20-30whp during long pulls or repeated runs versus the factory intercooler. This E-Chassis upgrade is ideal for setups up to 500whp, while the 7.5" RACE intercooler supports builds reaching 1000whp. Designed as a direct-fit replacement, the BMS intercooler is fully reversible and requires no additional hardware for installation. E-Chassis BMW FMIC Dimensions: 20" x 5.25" x 5.25".

Show More Show Less

BMS Billet Water/Methanol Injection Tank Cap With Safety Check Valve ...

T#:20815185

Part#: BMSWMITC

In Stock

$ 59.00 USD

Add to Wish List

Qty

$ 59.00 USD

Add to Wish List

The Burger Motorsports custom billet Water/Methanol Injection (WMI) cap includes an integrated heavy-duty check valve to let much-needed air in and prevent dangerous WMI vapor/fumes and liquid from getting out! Each cap is CNC machined in the USA from a solid block of billet aluminum, engraved with the BMS logo, and anodized blue for protection. Check valve piston must be lightly lubricated if tank shows signs of vacuum. One drop of penetrating oil or motor oil in the top will keep the check valve operational. Features and Benefits Integrated heavy-duty check valve lets air in but not out Specifically designed to prevent evaporation Keeps vapors inside the tank Made from a solid block of billet aluminum Blue anodizing for corrosion protection Exaggerated grips for easy removal Integrated heavy-duty o-ring Made in the USA

Show More Show Less

1 Gallon Methanol Tank - Clear/White

T#:558165

Part#: 1G-MT-CL

In Stock

$ 30.00 USD

Add to Wish List

Qty

$ 30.00 USD

Add to Wish List

The least expensive option available from BMS, this 1 gallon tank is compact and flexible allowing for a wide range of mounting on any flat vertical surface in the trunk. The tank is clear to allow visually checking the fluid level. Includes a 2-way vented black plastic cap and a compression pump feed fitting. Optional upgraded blue billet water/methanol injection (WMI) cap with 1-way check valve, ES4714530 Features & Benefits Available in clear for visually checking fluid levels 8 mounting holes on the side rails Includes 2-way vented black plastic cap Includes a compression pump feed fitting Made in USA Tank dimensions: L 11" x W 4.5 x H 9"

Show More Show Less

BMS DDP5800 Water/Methanol Injection Pump

T#:20815186

Part#: BMSDDP5800

Ships in 1 Business Day

Starting at $ 120.00 USD

Add to Wish List

Starting at $ 120.00 USD

Add to Wish List

The Burger Motorsports DDP 5800 water methanol alcohol Injection pump is a heavy-duty pump used in all of our BMS Water Injection kits. 200 psi bypass for smooth and high pressure and 1.3 GPM open flow. Made in the USA. Available with built-in quick connect fittings for 1/4" WMI line or with open 3/8" NPT threads if you plan to use braided lines.

Show More Show Less

2 Gallon Low Profile Universal Methanol Tank

T#:20946755

Part#: 2G-ULPMT

In Stock

Starting at $ 179.00 USD

Add to Wish List

Starting at $ 179.00 USD

Add to Wish List

Integrated pump mount for a super clean install. This tank allows the pump (sold separately) to mount to the bottom of the tank making for a clean and fast installation. It’s universal and will fit a wide variety of trunk applications. The larger capacity means more time between fill ups. Offered in black for a stealth appearance and in clear to allow visually checking the fluid level. Includes a 2-way vented black plastic cap and a compression pump feed fitting. Compatible with BMS DDP5800 pumps, ES4714512 or ES4714513 Optional upgraded blue billet water/methanol injection (WMI) cap with 1-way check valve, ES4714530 Pump mounts directly to the tank Compatible with all DDP 5800 pumps Super low profile design Available in clear for visually checking fluid levels Available in black for a stealth appearance Includes 2-way vented black plastic cap 4 mounting holes in the feet of the tank Includes a compression pump feed fitting, 2 90 degree push fittings, 9" of methanol line and pump mounting hardware. Made in the USA Tank dimensions: L 15.5" x W 8" x H 8.25"

Show More Show Less

1.25 Gallon Heavy-Duty Universal Methanol Tank

T#:20946761

Part#: 1.25G-UMT-CL

Ships on Sep 21, 2026

$ 69.00 USD

Add to Wish List

Qty

$ 69.00 USD

Add to Wish List

This tank is thicker and stronger than BMS' basic 1-gallon WMI tank. This tank features an easy fill filler nozzle, an anti-starvation reservoir with a pre-threaded bung for the included 90º compression pump feed fitting, a spill-catcher reservoir around the filler cap, a 2-way vented black plastic cap, and is translucent to allow visually checking the fluid level. Optional upgraded blue billet water/methanol injection (WMI) cap with 1-way check valve, ES4714530 Features & Benefits 1.25 Gallon Tank (4.73 Liters) Anti-Starvation Reservoir Easy Fill filler Nozzle Spill-Catcher Reservoir around the filler cap Available in clear for visually checking fluid levels 8 mounting holes on the side rails Includes 2-way vented black plastic cap Includes a 90º compression pump feed fitting Tank dimensions: L 11" x W 4.5 x H 9"

Show More Show Less

Burger Motorsport JB4-Compatible Water/Methanol Injection System - N2...

T#:558163

Part#: BMS-WMI

Ships on Sep 21, 2026

Starting at $ 226.99 USD

Add to Wish List

Starting at $ 226.99 USD

Add to Wish List

Looking to make loads of power on pump gas? Enter: water/methanol injection. Regardless if you're tuned for conventional pump gas, E85, or race fuel, use of a properly configured and integrated water/meth system will reduce temperatures, allowing you to make more power than on just conventional fuel alone. Select your engine-specific nozzles (which are standard 1/8" NPT and install in most aftermarket chargepipes), your tank to mount in the trunk, upgraded steel braided lines if you so choose, and some boost juice and you just need a management solution! Optionally, add a BMS FSB for JB4 integration!

Show More Show Less

Water/Methanol Injection Hose - 20'

T#:21176944

Part#: BMS-WMI-IL

In Stock

$ 31.99 USD

Add to Wish List

Qty

$ 31.99 USD

Add to Wish List

BMS Water/Methanol Injection (WMI) Solenoid W/ Filter

T#:21176934

Part#: BMS-WMI-SOL

Ships on Sep 21, 2026

$ 75.00 USD

Add to Wish List

Qty

$ 75.00 USD

Add to Wish List

This solenoid safely stops fluid from flowing into your intake system when WMI is not in use. The solenoid features two 1/8 NPT ports with included compression 1/4 in. hose fittings for a quick leak-free connection. The included filter keeps dirt and debris out of your engine.

Show More Show Less

WMI Inline Filter

T#:21176933

Part#: BMS-WMI-FIL

Ships on Sep 21, 2026

$ 15.00 USD

Add to Wish List

Qty

$ 15.00 USD

Add to Wish List

This heavy duty methanol/water injection filter is specifically designed for a methanol/water system can filter particles down to 40 microns in size. It safeguards the functional components of the water/methanol system as well as your engine from particulates present in the water/methanol mixture.

Show More Show Less

Super Atomizing Water/Methanol Injection Nozzles

T#:20815192

Part#: BMS.SA.WMI.NOZ

Ships on Oct 2, 2026

Starting at $ 40.00 USD

Add to Wish List

Starting at $ 40.00 USD

Add to Wish List

With CNC machined serviceable/cleanable nozzle inserts for precise fluid metering. Choose single or dual nozzles and match the flow rate to your power needs! Water/Methanol Injection (WMI) nozzles are determined by the intended power and how many bungs your charge pipe has. These nozzles are 1/8” NPT and screw in to bungs included on most aftermarket charge pipes. BMS "super atomizing" nozzles are designed and manufactured by BMS and are known for their great atomization and flow characteristics. The number on the methanol injection nozzle represents the approximate gallons per hour of fluid when at full flow. Generally speaking running two smaller nozzles is preferred to one larger nozzle for an equal flow to improve fluid atomization and distribution.

Show More Show Less

Project Cars

SELECT YOUR BMW

BMW Intake Parts for BMW 1 Series E82 (2008-2013)

Sub-Categories

BMS Replacement DCI Filters - Red

Burger Motorsport 4 BAR TMAP Sensor & Adapter - BMW N55/N54/S55 (2007...

BMS Replacement DCI Filters - Blue

Burger Motorsports Upgraded Intake Coupler - N55 BMW

Replacement N55 Performance Filter - Red

Intake Manifold Upgrade Kit

Turbosmart Raceport Gen-V Universal - Black (No Weld Flange) Female (...

TurboSmart GenV RacePort Blow-Off Valve - Blue

TurboSmart GenV RacePort Blow-Off Valve - Red - Female Flange ...

TurboSmart GenV RacePort Blow-Off Valve - Purple - Female Flange ...

BMS High Flow Silicone Inlets - 2" Opening For Hybrid Turbos - BMW N5...

Burger Motorsports 2007-2012 TypeA 4BAR Adapter - E82/88 E9X E6X N54 ...

BMS Replacement DCI Filters - White

Replacement Intake Coupler - Priced Each

BMW N54 BOV Vaccuum Adapter

BMS Replacement Intercooler For E Chassis BMW

BMS Billet Water/Methanol Injection Tank Cap With Safety Check Valve ...

1 Gallon Methanol Tank - Clear/White

BMS DDP5800 Water/Methanol Injection Pump

2 Gallon Low Profile Universal Methanol Tank

1.25 Gallon Heavy-Duty Universal Methanol Tank

Burger Motorsport JB4-Compatible Water/Methanol Injection System - N2...

Water/Methanol Injection Hose - 20'

BMS Water/Methanol Injection (WMI) Solenoid W/ Filter

WMI Inline Filter

Super Atomizing Water/Methanol Injection Nozzles

Select Vehicle

Purpose

Category

Brand

Price

Special Offers

Shipping

Narrow Results