Please ensure your correct model is selected
This product was last offered at the strikethrough price on
05-03-2026
This product was last offered at the strikethrough price on
05-03-2026
This product was last offered at the strikethrough price on
09-03-2026
This product was last offered at the strikethrough price on
09-03-2026
This product was last offered at the strikethrough price on
09-03-2026
This product was last offered at the strikethrough price on
09-03-2026
This product was last offered at the strikethrough price on
09-03-2026
This product was last offered at the strikethrough price on
09-03-2026
This product was last offered at the strikethrough price on
09-03-2026
This product was last offered at the strikethrough price on
09-03-2026
Vargas Turbo has you covered when you are installing a custom turbo setup. With all of the adapters you need and all the valves necessary, the only real limiting factor is your imagination!
The VTT PCV Flapper delete is used to get rid of the factory flapper, and add a -10 fitting on N54 powered vehicles. This will allow you to run a single or dual external catch can, or your own custom set up.
This fitting is made from 6061-T6 aircraft aluminum anodized black and comes with O-ring, and a stainless steel holding clip.
This part fits the following BMW engines:
2006-2012 N54
This product was last offered at the strikethrough price on
09-03-2026
This product was last offered at the strikethrough price on
09-03-2026
This product was last offered at the strikethrough price on
09-03-2026
This product was last offered at the strikethrough price on
09-03-2026
Vargas Turbo has you covered when you are installing a custom turbo setup. With all of the adapters you need and all the valves necessary, the only real limiting factor is your imagination!
This is a 1/2" (fits -8AN hos perfectly as well) CNC Billet check valve that can be used for a variety of uses including a vacuum/boost check valve when removing the stock PCV system, and still wanting to run the vacuum to the crankcase. Rated at over 100 psi, with a cracking psi of .25psi.
This part fits the following BMW engines:
2006-2012 N54
This product was last offered at the strikethrough price on
09-03-2026
This product was last offered at the strikethrough price on
09-03-2026
This product was last offered at the strikethrough price on
09-03-2026
This product was last offered at the strikethrough price on
09-03-2026
This product was last offered at the strikethrough price on
09-03-2026
This product was last offered at the strikethrough price on
09-03-2026
This product was last offered at the strikethrough price on
09-03-2026
This product was last offered at the strikethrough price on
09-03-2026
This product was last offered at the strikethrough price on
09-03-2026
This product was last offered at the strikethrough price on
09-03-2026
This product was last offered at the strikethrough price on
09-03-2026
This product was last offered at the strikethrough price on
09-03-2026
VTT is proud to offer the very best Cold Side charge pipe solution for the BMW E Series N54 platform. This system completely does away with the restrictive, and muli-connection stock charge pipe system, and replaces it with a single 6-ply, Heat Resistant, Wire reinforced silicone charge pipe rated at over 200 psi. They are molded for the perfect fit in your engine bay, while not sacrificing anything in the way of flow or size. They also completely isolate your charge air from any additional heat soak coming in from the engine or ambient heat. Another huge benefit is only TWO connections which are barbed and has many small ridges which dig into the silicone so it’s impossible for the pipe to blow off.
This N54 pipe has a flange installed to support a Turbosmart BOV.
This is the EASIEST N54 charge pipe on the market to install hands down. Install takes about half an hour even if you are inexperienced with working on your own car, can take as little as 15-20 minutes if you have had it apart a few times.
The kit includes:
VTT Cold Side Silicone Charge pipe
2 VTT Branded CNC adapters to mount the map sensor, and a methanol bung
1 VTT Branded CNC adapters for the TB inlet
2 VTT branded T-Bolt Clamps
1 1/8 NPT port is included in the charge pipe for methanol
This product was last offered at the strikethrough price on
09-03-2026
This product was last offered at the strikethrough price on
09-03-2026
Vargas Turbo has you covered when you are installing a custom turbo setup. With all of the adapters you need and all the valves necessary, the only real limiting factor is your imagination!
This is the adapter fitting that is required to convert your N54 to external PCV if you want to keep your crankcase under vacuum at idle, and anytime you have a vacuum condition in your intake manifold. They are made from 6061-T6 with black anodizing for a long-lasting finish. Includes complete adapter, with all o-rings, and retaining clip.
This must be used in conjunction with the Vargas billet check valve, and PCV delete fitting or requires plugging of the intake PCV ports. Installs inline on the throttle body, and adds a -8AN male to adapt to a catch cans, or any custom set up.
Made from 6061-T6 with black anodizing for a long-lasting finish. Includes complete adapter, with all o-rings, and retaining clip
This part fits the following BMW engines:
2006-2012 N54
This product was last offered at the strikethrough price on
09-03-2026
This product was last offered at the strikethrough price on
09-03-2026
This product was last offered at the strikethrough price on
09-03-2026
This product was last offered at the strikethrough price on
09-03-2026
This product was last offered at the strikethrough price on
09-03-2026
This product was last offered at the strikethrough price on
09-03-2026
This product was last offered at the strikethrough price on
09-03-2026
This product was last offered at the strikethrough price on
09-03-2026
This product was last offered at the strikethrough price on
09-03-2026
This product was last offered at the strikethrough price on
09-03-2026
