BMW Intake Parts for BMW 1 Series E82 (2008-2013)

Replacement N55 Performance Filter from Burger Motorsport

Enhance your BMW's performance with the Replacement N55 Performance Filter from Burger Motorsport. Specifically designed for N55 engines, this filter optimizes airflow, leading to increased horsepower and torque. Enjoy improved throttle response and fuel efficiency, all while protecting your engine from harmful contaminants.

Key Features:

• Designed for N55 engines
• Optimizes airflow for increased power
• Improves throttle response and fuel efficiency
• Protects engine from contaminants

In BMW's with the N55, the intake system is partially limited. The bottom portion is lightweight and great for feeding cold air to the intake, but the top portion is excessively restrictive. Working with some of the original equipment, this intake continues to utilize the bottom portion of OE ducting and heat shielding, but replaces the top with new high flow ducting and a performance filter. Extensive testing showed up to a 10+ HP gain to the wheels and allows for quicker turbo spool speed. Plus, this design gives you a great sound improvement, letting you hear both the intake and turbo spooling!

Installation and removal is extremely quick and easy, taking only 5 minutes in the driveway!

Features:

• Adds up to 10+ Horsepower
• Dramatic sound improvement
• Super fast install and removal
• Improves throttle response 
• Retains OEM airbox base as a heat shield
• Retains OEM cold air ducting
• Looks great under the hood
• Cleanable and reusable filter
• Made in the USA

Vargas Turbo has you covered when you are installing a custom turbo setup. With all of the adapters you need and all the valves necessary, the only real limiting factor is your imagination!

The VTT PCV Flapper delete is used to get rid of the factory flapper, and add a -10 fitting on N54 powered vehicles. This will allow you to run a single or dual external catch can, or your own custom set up.

This fitting is made from 6061-T6 aircraft aluminum anodized black and comes with O-ring, and a stainless steel holding clip.

This part fits the following BMW engines:
2006-2012 N54

Vargas Turbo has you covered when you are installing a custom turbo setup. With all of the adapters you need and all the valves necessary, the only real limiting factor is your imagination!

This is a 1/2" (fits -8AN hos perfectly as well) CNC Billet check valve that can be used for a variety of uses including a vacuum/boost check valve when removing the stock PCV system, and still wanting to run the vacuum to the crankcase. Rated at over 100 psi, with a cracking psi of .25psi.

This part fits the following BMW engines:
2006-2012 N54

• Seamless plug-and-play installation
• Minimizes leakage for enhanced turbocharger performance
• Retains OE control for optimal operation
• Superior thermal performance to maximize boost without stressing the turbocharger

If you are looking to replace your stock chargepipe for better reliability and higher performance, the Burger Motorsports designed and Phoenix Racing built Performance Aluminum Chargepipe is an excellent choice! This aluminum chargepipe is significantly stronger than the stock plastic pipe and the powder coated aluminum looks great and will resist any corrosion. Plus, this chargepipe features a 3 inch design for optimal flow at all RPMs, prevent restriction that would normally be seen with the stock pipe. This is perfect for someone looking to upgrade a stock or tuned N54!

Specs and Features:

• Aluminum Construction
• Black Powder Coating
• 3" Diameter
• CNC Machined Throttle Body Flange
• Dual 1/8" NPT Bungs
• High Pressure T-Bolt Clamps
• All Required Installation Hardware

O-rings and retaining clip must be reused from the original pipe or purchased new for proper installation.

Vargas Turbo has you covered when you are installing a custom turbo setup. With all of the adapters you need and all the valves necessary, the only real limiting factor is your imagination!

This is the adapter fitting that is required to convert your N54 to external PCV if you want to keep your crankcase under vacuum at idle, and anytime you have a vacuum condition in your intake manifold. They are made from 6061-T6 with black anodizing for a long-lasting finish. Includes complete adapter, with all o-rings, and retaining clip.

This must be used in conjunction with  the Vargas billet check valve, and PCV delete fitting or requires plugging of the intake PCV ports. Installs inline on the throttle body, and adds a -8AN male to adapt to a catch cans, or any custom set up.

Made from 6061-T6 with black anodizing for a long-lasting finish. Includes complete adapter, with all o-rings, and retaining clip

This part fits the following BMW engines: 
2006-2012 N54