Fuel Injectors for BMW 1 Series E82 (2008-2013)

VTT N54 Vacuum Pump Block Off Plate

2X Entries Into Our F80 M3 Sweepstakes

T#:11497328

Part#: VTT-N54-VACUUM-B

Ships in 10 Business Days

$ 127.99 USD

Add to Wish List

Qty

$ 127.99 USD

Add to Wish List

Looking to remove the HPFP or DI system on your N54? this plate will block the vacuum pump and prevent oil leaks. You will need to remove any fuel lines, etc. Kit includes Block Plate Note – Plates may come in a clear or anodize black finish depending on stock on hand

Show More Show Less

VTT BMW N54 “DI Injector” Delete Kit

2X Entries Into Our F80 M3 Sweepstakes

T#:11497326

Part#: VTT-N54-DI-DELET

Ships in 1 Business Day

$ 339.99 USD

Add to Wish List

Qty

$ 339.99 USD

Add to Wish List

Looking to get rid of the troublesome and expensive DI injectors on your BMW N54 and move to PI only and a standalone? If so VTT has you covered with its new N54 PI delete kit. This kit allows you to SAFELY remove the DI injectors, install our delete fittings, and run PI only. We machined these deletes from 310 Stainless for extreme heat, and corrosion resistance, and include 3 hold downs. These DI deletes COMPLETELY get rid of all factory provisions, including the seal. If the seal is left intact with no fuel to cool the injector or delete it will quickly overheat and melt the delicate seal causing combustion gasses to escape the engine creating misfires, and worse possibly damaging your injector bore on the cylinder head. Our deletes are machined to be a press fit into the cylinder, and can be either cooled with liquid nitrogen, and dropped in, or tapped in with a hammer, and then held down with the included hold downs. We also include M6 tapped holes on the top of each one in case they need to be removed you can attach a slide hammer, and remove the delete. These are sold as a kit and come with the following 6 – 310 Stainless DI Delete fittings 3 – Hold down brackets Completetion of this kit will require the purchase of HPFP delete plate - ES# 4623950 PLEASE NOTE: THIS KIT REQUIRES EXTENSIVE MODIFICATIONS TO CONVERT YOUR ENGINE TO PI ONLY. THIS INCLUDES BUT IS NOT LIMITED TO A FULL PORT INJECTION SOLUTION, AND STAND-ALONE TO RUN THE PI SYSTEM. WE RECOMMEND THIS PNP SYSTEM USING THE MAXX ECU IT PROVIDES ALL YOU NEED TO GET UP AND RUNNING WITH PI ONLY ON THE TUNING SIDE OF THINGS – https://www.pnpecu.com/pnpecu-maxxecu-n54-pnp-kit-437-p.asp

Show More Show Less

Precision Raceworks In-Line Micro Regulator - 5 Bar

T#:38094305

Part#: 601-0260

Back Ordered

$ 64.99 USD

Add to Wish List

Qty

$ 64.99 USD

Add to Wish List

For enthusiasts seeking to regulate fuel pressure at the engine without the complexities of manual adjustments or the need for a 1:1 boost reference, a preset fuel pressure regulator offers an ideal solution. These compact regulators are designed for straightforward installation and consistent performance.

Show More Show Less

Fuel Injector Replacement Kit - N52

10X Entries Into Our F80 M3 Sweepstakes

T#:53044116

Part#: 13537531634RKT2

Ships on Oct 15, 2026

Sale - Save 22% $ 318.99

This product was last offered at the strikethrough price on
05-03-2026

$ 247.50 USD

Add to Wish List

Qty

Sale - Save 22%

$ 318.99

This product was last offered at the strikethrough price on
05-03-2026

$ 247.50 USD

Add to Wish List

Restore engine performance and drivability by replacing those old, high mileage fuel injectors. Includes injector clips.

Black Market Parts Multi-Port Injection Kit - 950cc - BMW N54/N55 3.0...

T#:38262759

Part#: 601-0188

In Stock

$ 959.99 USD

Add to Wish List

Qty

$ 959.99 USD

Add to Wish List

If you plan on upgrading your turbos or increasing power in some other way, you will also want to consider upgrading your fueling capability as well! Using stock BMW injectors, you will likely top out at around 550rwhp on 93 Octane with water/methanol injection (or less if running an ethanol blend). At the end of the day, the stock injectors just are not enough. Introducing Black Market Parts (by Precision Raceworks) Multi-Port Injection Kit with flex-fuel compatibility! This kit allows you to safely and sufficiently support greater power levels with supplemental fueling without straining your stock fuel system. This kit integrates seamlessly into your car as if it were installed at the factory; you can’t even see the kit once the car is assembled! This kit includes everything needed to add multi-port injection and is 100% e85 compliant. Precision Raceworks includes new Genuine Bosch injectors which are flow matched both static and dynamic by an outside lab to industry-leading requirements. A Detailed certificate of conformance and genuine Bosch product certificate is included with each kit, giving you all flow data needed for optimal tuning. Don’t be tricked into thinking all port injection kits are equal, the BMP kit is the industry leader. This kit features 950cc* injectors standard (this flow rate is based on industry-standard injector flow test pressure of 43.5psi). This means Precision's BMP Port Injection Kit is capable of supporting builds from 500whp up to 1,000+whp and anywhere in between! Simply pick up this kit and pair it with your favorite injector controller and you are ready to go!

Show More Show Less

Precision Raceworks In-Line Micro Regulator - 6 Bar

T#:38094308

Part#: 601-0261

Ships in 9 Business Days

$ 64.99 USD

Add to Wish List

Qty

$ 64.99 USD

Add to Wish List

For enthusiasts seeking to regulate fuel pressure at the engine without the complexities of manual adjustments or the need for a 1:1 boost reference, a preset fuel pressure regulator offers an ideal solution. These compact regulators are designed for straightforward installation and consistent performance.

Show More Show Less

Black Market Parts Multi-Port Injection Kit - 750cc - BMW N54/N55 3.0...

T#:1316810

Part#: 601-0015

In Stock

$ 699.99 USD

Add to Wish List

Qty

$ 699.99 USD

Add to Wish List

If you plan on upgrading your turbos or increasing power in some other way, you will also want to consider upgrading your fueling capability as well! Using stock BMW injectors, you will likely top out at around 550rwhp on 93 Octane with water/methanol injection (or less if running an ethanol blend). At the end of the day, the stock injectors just are not enough. Introducing Black Market Parts (by Precision Raceworks) Multi-Port Injection Kit with flex-fuel compatibility! This kit allows you to safely and sufficiently support greater power levels with supplemental fueling without straining your stock fuel system. This kit integrates seamlessly into your car as if it were installed at the factory; you can’t even see the kit once the car is assembled! This kit includes everything needed to add multi-port injection and is 100% e85 compliant. Precision Raceworks includes new Genuine Bosch injectors which are flow matched both static and dynamic by an outside lab to industry-leading requirements. A Detailed certificate of conformance and genuine Bosch product certificate is included with each kit, giving you all flow data needed for optimal tuning. Don’t be tricked into thinking all port injection kits are equal, the BMP kit is the industry leader. This kit features 750cc* injectors standard (this flow rate is based on industry-standard injector flow test pressure of 43.5psi), and at 72psi these injectors flow over 1000cc. This means Precision's BMP Port Injection Kit is capable of supporting builds from 400whp up to 1,000whp and anywhere in between! Simply pick up this kit and pair it with your favorite injector controller and you are ready to go!

Show More Show Less

Black Market Parts Multi-Port Injection Kit - No Injectors - BMW N54/...

T#:38262760

Part#: 601-0227

Ships in 9 Business Days

$ 429.99 USD

Add to Wish List

Qty

$ 429.99 USD

Add to Wish List

If you plan on upgrading your turbos or increasing power in some other way, you will also want to consider upgrading your fueling capability as well! Using stock BMW injectors, you will likely top out at around 550rwhp on 93 Octane with water/methanol injection (or less if running an ethanol blend). At the end of the day, the stock injectors just are not enough. Introducing Black Market Parts (by Precision Raceworks) Multi-Port Injection Kit with flex-fuel compatibility! This kit allows you to safely and sufficiently support greater power levels with supplemental fueling without straining your stock fuel system. This kit integrates seamlessly into your car as if it were installed at the factory; you can’t even see the kit once the car is assembled! This kit includes everything needed to add multi-port injection and is 100% e85 compliant. Precision Raceworks includes new Genuine Bosch injectors which are flow matched both static and dynamic by an outside lab to industry-leading requirements. A Detailed certificate of conformance and genuine Bosch product certificate is included with each kit, giving you all flow data needed for optimal tuning. Don’t be tricked into thinking all port injection kits are equal, the BMP kit is the industry leader. This kit features 750cc* injectors standard (this flow rate is based on industry-standard injector flow test pressure of 43.5psi), and at 72psi these injectors flow over 1000cc. This means Precision's BMP Port Injection Kit is capable of supporting builds from 400whp up to 1,000whp and anywhere in between! Simply pick up this kit and pair it with your favorite injector controller and you are ready to go!

Show More Show Less

Precision Raceworks In-Line Micro Regulator - 4 Bar

T#:38195450

Part#: 601-0259

Ships in 9 Business Days

$ 64.99 USD

Add to Wish List

Qty

$ 64.99 USD

Add to Wish List

For enthusiasts seeking to regulate fuel pressure at the engine without the complexities of manual adjustments or the need for a 1:1 boost reference, a preset fuel pressure regulator offers an ideal solution. These compact regulators are designed for straightforward installation and consistent performance.

Show More Show Less

Precision Raceworks Port Injection Plugs - Replaces EV14 Style Inject...

T#:18003817

Part#: PRINJPLGS

Ships in 9 Business Days

Starting at $ 9.99 USD

Add to Wish List

Starting at $ 9.99 USD

Add to Wish List

Use these in replacement of any standard short body EV14 style injector. These include appropriate o-rings for any of Precision Raceworks' port injection kits, including their aftermarket manifolds. Unlike other injector plugs, these feature shoulders to prevent the plug from sliding too far in either direction

Show More Show Less

Project Cars

SELECT YOUR BMW

Fuel Injectors for BMW 1 Series E82 (2008-2013)

VTT N54 Vacuum Pump Block Off Plate

VTT BMW N54 “DI Injector” Delete Kit

Precision Raceworks In-Line Micro Regulator - 5 Bar

Fuel Injector Replacement Kit - N52

Black Market Parts Multi-Port Injection Kit - 950cc - BMW N54/N55 3.0...

Precision Raceworks In-Line Micro Regulator - 6 Bar

Black Market Parts Multi-Port Injection Kit - 750cc - BMW N54/N55 3.0...

Black Market Parts Multi-Port Injection Kit - No Injectors - BMW N54/...

Precision Raceworks In-Line Micro Regulator - 4 Bar

Precision Raceworks Port Injection Plugs - Replaces EV14 Style Inject...

Select Vehicle

Purpose

Category

Brand

Price

Special Offers

Shipping

Narrow Results