BMW Z Series E85/6 (2003-2008)

AeroCatch Racing Hood and Body Panel Fasteners (Pair) - Better than h...

T#:340098

Part#: AEROCATCH

In Stock

$ 566.99

This product was last offered at the strikethrough price on
05-13-2026

Starting at $ 82.99 USD

Add to Wish List

Starting at $ 82.99 USD

Add to Wish List

As used by Turner Motorsport on our championship winning BMW race cars, the new aerodynamically efficient and aesthetically styled AeroCatch is setting new standards in hood fixing for the 21st century. Say goodbye to your standard hood pins -- these are better all around.

Show More Show Less

KMAC Stage 1 Street Front Adjustable Camber/Caster Plates - E36, E39 ...

T#:389645

Part#: 192416-1J

In Stock

$ 380.00 USD

Add to Wish List

Qty

$ 380.00 USD

Add to Wish List

Location: Front
Type: Street, Stage 1
Bearing: captive-ball fully encased in polyurethane

These front adjustable camber/caster plates will replace your stock front upper strut bearing. The KMAC plates are a 'floating' design so camber and caster are adjusted together. This design allows maximum range of adjustment since no other hardware interferes with the adjustments. Since these replace your stock strut bearings they are designed to work with a stock-type spring only. And when installed correctly will not significantly alter ride height. Adjustment is easily done by loosening the three nuts on top of the tower and sliding the camber plate into the position you want, then re-tighten the nuts. These mounts can be installed two ways - for camber correction or swapped side-side for increasing negative camber. Detailed instructions included.

Note: suspensions vary from manufacturer to manufacturer. Turner Motorsport cannot be responsible for fitment issues caused by non-stock or specialized coil-over suspensions. As with any race-derived component, additonal fabrication may be required.

This item fits the following BMWs:
2008-2012 E82 BMW 128i 135i
6/1992-1999 E36 BMW 318i 318is 318ti 318ic 323is 323ic 325i 325is 325ic 328i 328is 328ic M3
1999-2005 E46 BMW 323i 323ci 325i 325ci 325xi 328i 328ci 330i 330ci 330xi
2006-2011 E90 BMW 325i 328i 330i 335d 335i - Sedan
2006-2012 E91 BMW 328i - Wagon
2007-2013 E92 BMW 328i 335i 335is - Coupe
2007-2013 E93 BMW 328i 335i - Convertible
1997-2003 E39 BMW 525i 528i 530i 540i (not for cars with EDC)
2004-2010 E60 BMW 525i 530i 528i 535i 545i 550i
2004-2011 E63 E64 BMW 645ci 650i
1997-2002 Z3 BMW Z3 1.9 Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i M Roadster M Coupe
2003-2008 E85 BMW Z4 2.5i Z4 3.0i Z4 3.0si
2009+ Z4 BMW Z4 sDrive28i Z4 sDrive30i Z4 sDrive35i Z4 sDrive35is
2000-2003 E52 BMW Z8 Roadster (without EDC)

Show More Show Less

Seat Floor Adapters - E36, E46, E85 - Macht Schnell

T#:300563

Part#: 79.10.101B

Ships on Aug 28, 2026

$ 235.00 USD

Add to Wish List

Qty

$ 235.00 USD

Add to Wish List

In order to mount aftermarket seats in your car, you need a floor mount adapter. These high-quality aluminum adapters are made by Macht Schnell. These bolt to your existing seat mounting studs in the floor and offer the lowest profile of any floor mount (22mm height). This helps to keep your seat at the lowest position possible. Your seat adapters or sliders bolt to this adapter plate. These floor mounts are a matrix style with rows of threaded holes that allow you to find an ideal seat location. There are other options - including homemade - but these seat brackets for your BMW are the highest quality to match your expensive seats.

Sold per seat. Can be used on left or right sides of vehicle.

These adapters were originally designed for the E46 chassis. They can fit the E36 by modifying the mounting holes to match the bolt and stud locations on the E36 floor.

This item fits the following BMWs:
1995-1999 E36 BMW 318i 318is 318ti 318i 323is 323i 325i 325is 325i 328i 328is 328i M3 (except convertibles) ( see note above )
1999-2005 E46 BMW 323i 323ci 325i 325ci 325xi 328i 328ci 330i 330ci 330xi M3 (except convertibles)
2003-2008 E85 E86 BMW Z4 2.5i Z4 3.0i Z4 3.0si Z4 M Roadster M Coupe

Show More Show Less

Active Autowerke Rotrex Traction Fluid - One Liter

T#:397307

Part#: 12-032

Ships in 1 Business Day

$ 240.00 USD

Add to Wish List

Qty

$ 240.00 USD

Add to Wish List

Rotrex superchargers utilize a unique traction drive system that sets it apart from other centrifugal-style superchargers. For best performance, Rotrex recommends replacing this fluid every 50,000 miles. This bottle of traction fluid is plenty enough for one supercharger service (typically 750ml).

Show More Show Less

Autel Universal Rubber TPMS Sensor - Set Of Four

T#:3529121

Part#: AUL1SENSORKT

In Stock

$ 243.99 USD

Add to Wish List

Qty

$ 243.99 USD

Add to Wish List

Black Forest Industries Billet Heavy Weight Shift Knob - Alcantara Or...

T#:391722

Part#: GS2B

In Stock

Starting at $ 184.99 USD

Add to Wish List

Starting at $ 184.99 USD

Add to Wish List

This weighted shift knob makes shifts faster and the extra-large globe shape encourages over-palm shifting. The Black Forest Industries Billet Knob weighs in at 8.8oz (250g), about twice as much as a stock knob and a little heaver than the BMW ZHP knob. The heavier knob amplifies the pendulum motion of the shift lever resulting in smoother and faster shift times. BFI has designed this knob for BMW and VW fitments to fit snug on the shift lever and be secured with Allen set screws. They were careful to reduce tolerances compared to universal knobs. The overall height of the BFI knob is the same as stock anatomic knobs (some BMW M/Performance models have a stock knob that is shorter than this one).

Included with the BFI Billet knob is a matching BFI crest shift emblem. A 5 or 6-speed pattern emblem is available separately.

Choose from soft alcantara or perforated air leather with either a silver or black anodized base.

Show More Show Less

GSP Rear Axle Assembly - Right - E46, Z4

T#:389701

Part#: NCV27516

Ships in 2 Business Days

$ 183.99 USD

Add to Wish List

Qty

$ 183.99 USD

Add to Wish List

Since established in 2004, GSP North America has positioned itself as a leading supplier of New Axles in North America.GSP’s new axle program consistently offers the best application coverage, most SKU count, and more new numbers than any other competitors. GSP’s hub assembly program was introduced to North America market in 2010 and has grown into one the most trustable programs in US market.

This item fits the following BMWs:

E46 BMW M3

E85 BMW Z4M

Show More Show Less

BFI GS2 Automatic Shift Knob - Black w/ Black Alcantara - E82/88 E9X ...

T#:4813288

Part#: GS2-BMA-2SU

Ships on Aug 17, 2026

$ 229.99 USD

Add to Wish List

Qty

$ 229.99 USD

Add to Wish List

Introducing the world's first Black Forest Industries shift knob specifically for Automatic transmission BMW applications. Built with the same quality materials as our other GS2 shift knobs, this application adds a control lever and internal springs to operate the automatic mechanism of a BMW shift lever.

Show More Show Less

BFI GS2 Automatic Shift Knob - Black w/ Rosso Centaurus (Red) Perfora...

T#:4813291

Part#: GS2-BMA-2SRC

Ships on Aug 17, 2026

$ 224.99 USD

Add to Wish List

Qty

$ 224.99 USD

Add to Wish List

Introducing the world's first Black Forest Industries shift knob specifically for Automatic transmission BMW applications. Built with the same quality materials as our other GS2 shift knobs, this application adds a control lever and internal springs to operate the automatic mechanism of a BMW shift lever.

Show More Show Less

BFI GS2 Automatic Shift Knob - Silver w/ Rosso Centaurus (Red) Perfor...

T#:4813293

Part#: GS2-BMA-2RC

Ships on Aug 17, 2026

$ 219.99 USD

Add to Wish List

Qty

$ 219.99 USD

Add to Wish List

Introducing the world's first Black Forest Industries shift knob specifically for Automatic transmission BMW applications. Built with the same quality materials as our other GS2 shift knobs, this application adds a control lever and internal springs to operate the automatic mechanism of a BMW shift lever.

Show More Show Less

BFI GS2 Automatic Shift Knob - Black w/ Red Alcantara - E82/88 E9X E8...

T#:4813290

Part#: GS2-BMA-2SRU

Ships on Aug 17, 2026

$ 229.99 USD

Add to Wish List

Qty

$ 229.99 USD

Add to Wish List

Introducing the world's first Black Forest Industries shift knob specifically for Automatic transmission BMW applications. Built with the same quality materials as our other GS2 shift knobs, this application adds a control lever and internal springs to operate the automatic mechanism of a BMW shift lever.

Show More Show Less

GSP Rear Axle Assembly - Left - E46, Z4

T#:389714

Part#: NCV27500

Ships in 2 Business Days

$ 178.99 USD

Add to Wish List

Qty

$ 178.99 USD

Add to Wish List

Since established in 2004, GSP North America has positioned itself as a leading supplier of New Axles in North America.GSP’s new axle program consistently offers the best application coverage, most SKU count, and more new numbers than any other competitors. GSP’s hub assembly program was introduced to North America market in 2010 and has grown into one the most trustable programs in US market.

This item fits the following BMWs:

E46 BMW M3

E85 BMW Z4M

Show More Show Less

Active Autowerke Signature Trunk Emblem

T#:590914

Part#: AASIGNATUREPLAQU

Ships in 3 Business Days

4% off MSRP $ 45.00

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 43.00 USD

Add to Wish List

Qty

4% off MSRP

$ 45.00

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 43.00 USD

Add to Wish List

Stand out from the crowd, and give them a hint of what you've got going on under the hood, with the official Active Autowerke Signature Emblem! The emblem can be placed anywhere on the exterior, or interior of your BMW. Hefty stainless steel construction and durable double-sided tape will help ensure that it is never lost, even at speeds over 170+ MPH...Don't ask us how we know! Represent your favorite BMW tuner for all to see today!

Show More Show Less

7 pc. 3/8" Dr. Spark Plug Socket Set

T#:641915

Part#: 8845D

Ships in 6 Business Days

$ 141.99 USD

Add to Wish List

Qty

$ 141.99 USD

Add to Wish List

Complete set of spark plug sockets.

BFI GS2 Automatic Shift Knob - Silver w/ Black Perforated Air Leather...

T#:4813284

Part#: GS2-BMA-2

Ships on Aug 17, 2026

$ 219.99 USD

Add to Wish List

Qty

$ 219.99 USD

Add to Wish List

Introducing the world's first Black Forest Industries shift knob specifically for Automatic transmission BMW applications. Built with the same quality materials as our other GS2 shift knobs, this application adds a control lever and internal springs to operate the automatic mechanism of a BMW shift lever.

Show More Show Less

BFI GS2 Automatic Shift Knob - Silver w/ Black Alcantara - E82/88 E9X...

T#:4813285

Part#: GS2-BMA-2U

Ships on Aug 17, 2026

$ 224.99 USD

Add to Wish List

Qty

$ 224.99 USD

Add to Wish List

Introducing the world's first Black Forest Industries shift knob specifically for Automatic transmission BMW applications. Built with the same quality materials as our other GS2 shift knobs, this application adds a control lever and internal springs to operate the automatic mechanism of a BMW shift lever.

Show More Show Less

BFI GS2 Automatic Shift Knob - Black w/ Gray Alcantara - E82/88 E9X E...

T#:4813289

Part#: GS2-BMA-2SUF

Ships on Aug 17, 2026

$ 229.99 USD

Add to Wish List

Qty

$ 229.99 USD

Add to Wish List

Introducing the world's first Black Forest Industries shift knob specifically for Automatic transmission BMW applications. Built with the same quality materials as our other GS2 shift knobs, this application adds a control lever and internal springs to operate the automatic mechanism of a BMW shift lever.

Show More Show Less

ACM Blower Motor Resistor - E70, E71, E82, E88, E90, E91, E92, E93, Z...

T#:377148

Part#: 64119265892

Ships in 1-2 days

$ 121.99

This product was last offered at the strikethrough price on
05-07-2026

$ 118.99 USD

Add to Wish List

Qty

$ 118.99 USD

Add to Wish List

Used to control the speed of the blower motor, commonly referred to as the FSU

Seatbelt 4-point Race Harness Receptacles - Macht Schnell

T#:338505

Part#: 79.12.15X

Ships on Aug 20, 2026

Starting at $ 125.00 USD

Add to Wish List

Starting at $ 125.00 USD

Add to Wish List

If you're going to use a 4 point racing harness with your racing or sport seat and don't want to drill through your floor and carpet, these harness adapter plates are perfect*. These sandwich in between your slider and seat bracket for a strong and secure mounting point. They are made from high-strength steel and powedercoated in stealthy black. Choose from a bolt-in or clip-in style harness end. These will only work with the Macht Schnell floor mounts.

* - note that most racing harness manufacturers will advise that drilling through the floor is the best method for mounting harnesses. This allows you to locate the mount in the ideal location and angle to fit your driving position. The proper installation is paramount to ensure the harness works correctly in an impact.

Sold per seat.

This item fits the following BMWs:
2008-2012 E82 BMW 128i 135i 1M Coupe
1992-1998 E36 BMW 318i 318is 318ti 323is 325i 325is 328i 328is M3
1999-2005 E46 BMW 323i 323ci 325i 325ci 325xi 328i 328ci 330i 330ci 330xi M3 (not convertibles)
2006-2011 E90 BMW 325i 325xi 328i 328xi 328i xDrive 330i 330xi 335d 335i 335xi 335i xDrive M3 - Sedan
2006-2012 E91 BMW 325xi 328i 328xi 328i xDrive - Wagon
2007-2013 E92 BMW 328i 328xi 328i xDrive 335i 335is 335xi 335i xDrive M3 - Coupe
2003-2008 E85 BMW Z4 2.5i Z4 3.0i Z4 3.0si Z4 M Roadster M Coupe

Show More Show Less

14 Pc. Full Polish SAE Angle Head Wrench Set

T#:642035

Part#: 9914A

Ships on Aug 17, 2026

$ 113.91 USD

Add to Wish List

Qty

$ 113.91 USD

Add to Wish List

Radius V-Groove design creates an anti-slip while also preventing round-off.

KMAC Stage 2 Street/Track Front Adjustable Camber/Caster Plates - E36...

T#:389647

Part#: 192416-2L

Special Order: No Guaranteed ETA

$ 545.00 USD

Add to Wish List

Qty

$ 545.00 USD

Add to Wish List

Location: Front
Type: Street/Track, Stage 2
Bearings: main PTFE-lined pillow-ball bearing suspended in polyurethane; self-lubricating radial axial bearing/bushing in upper spring plate
Springs: includes OEM size upper spring perch, 60mm upper spring perch, and 2.5" upper spring perch

The Stage 2 KMAC plates are a mixed track and street camber/caster plate meant to be used in a variety of suspensions and setups. Since there is less bushing than on the Stage 1, more noise and vibration will reach the driver. The adjustment design is similar to the Stage 1 with a floating mount that sets camber and caster simultaneously. This design allows maximum range of adjustment since no other hardware interferes with the adjustments. These plates can work on both coil over and stock-stype suspensions and upper spring perches are included for OEM springs, 60mm, and 2.5" coil over springs. The upper perch assembly incorporate a self-sliding radial bushing that allows the spring to spin during its travel instead of bind. This reduces tension on the spring and helps reduce noise and spring 'popping' noises. Bearing inserts, spacers for correct articulating angles, and 3 sizes of upper nut adapters included. The urethane bushings and bearings are replaceable if they wear out. These are designed mainly for adding negative camber for improved handling and not for camber correction back to stock settings (see Stage 1 kit). Basic instructions included but professional installation is required.

Note: suspensions vary from manufacturer to manufacturer. The proper stacked height and clearances are required. K-Mac includes bearing adapters, spacers, and various top nuts but it is still the responsibility of the installer to ensure a correct and safe fitment. As with any race-derived component, additonal fabrication may be required.

This item fits the following BMWs:
2008-2012 E82 BMW 128i 135i
6/1992-1999 E36 BMW 318i 318is 318ti 318ic 323is 323ic 325i 325is 325ic 328i 328is 328ic M3
1999-2005 E46 BMW 323i 323ci 325i 325ci 325xi 328i 328ci 330i 330ci 330xi
2006-2011 E90 BMW 325i 328i 330i 335d 335i - Sedan
2006-2012 E91 BMW 328i - Wagon
2007-2013 E92 BMW 328i 335i 335is - Coupe
2007-2013 E93 BMW 328i 335i - Convertible
1997-2003 E39 BMW 525i 528i 530i 540i (not for cars with EDC)
2004-2010 E60 BMW 525i 530i 528i 535i 545i 550i
2004-2011 E63 E64 BMW 645ci 650i
1997-2002 Z3 BMW Z3 1.9 Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i M Roadster M Coupe
2003-2008 E85 BMW Z4 2.5i Z4 3.0i Z4 3.0si
2009+ Z4 BMW Z4 sDrive28i Z4 sDrive30i Z4 sDrive35i Z4 sDrive35is
2000-2003 E52 BMW Z8 Roadster (without EDC)

Show More Show Less

KMAC Stage 3 Street/Track Front Adjustable Camber/Caster Plates - E36...

T#:389646

Part#: 192416-3L

Special Order: No Guaranteed ETA

$ 545.00 USD

Add to Wish List

Qty

$ 545.00 USD

Add to Wish List

Location: Front
Type: Street/Track, Stage 2
Bearings: main PTFE-lined pillow-ball bearing suspended in polyurethane; self-lubricating radial axial bearing/bushing in upper spring plate
Springs: includes OEM size upper spring perch, 60mm upper spring perch, and 2.5" upper spring perch

The Stage 3 KMAC plates are a mixed track and street camber/caster plate meant to be used in a variety of suspensions and setups. Since there is less bushing than on the Stage 1, more noise and vibration will reach the driver. The adjustment design is similar to the Stage 1 with a floating mount that sets camber and caster simultaneously. This design allows maximum range of adjustment since no other hardware interferes with the adjustments. These plates can work on both coil over and stock-stype suspensions and upper spring perches are included for OEM springs, 60mm, and 2.5" coil over springs. The upper perch assembly incorporate a self-sliding radial bushing that allows the spring to spin during its travel instead of bind. This reduces tension on the spring and helps reduce noise and spring 'popping' noises. Bearing inserts, spacers for correct articulating angles, and 3 sizes of upper nut adapters included. The urethane bushings and bearings are replaceable if they wear out. These are designed mainly for adding negative camber for improved handling and not for camber correction back to stock settings (see Stage 1 kit). Basic instructions included but professional installation is required.

Note: suspensions vary from manufacturer to manufacturer. The proper stacked height and clearances are required. K-Mac includes bearing adapters, spacers, and various top nuts but it is still the responsibility of the installer to ensure a correct and safe fitment. As with any race-derived component, additonal fabrication may be required.

This item fits the following BMWs:
2008-2012 E82 BMW 128i 135i
6/1992-1999 E36 BMW 318i 318is 318ti 318ic 323is 323ic 325i 325is 325ic 328i 328is 328ic M3
1999-2005 E46 BMW 323i 323ci 325i 325ci 325xi 328i 328ci 330i 330ci 330xi
2006-2011 E90 BMW 325i 328i 330i 335d 335i - Sedan
2006-2012 E91 BMW 328i - Wagon
2007-2013 E92 BMW 328i 335i 335is - Coupe
2007-2013 E93 BMW 328i 335i - Convertible
1997-2003 E39 BMW 525i 528i 530i 540i (not for cars with EDC)
2004-2010 E60 BMW 525i 530i 528i 535i 545i 550i
2004-2011 E63 E64 BMW 645ci 650i
1997-2002 Z3 BMW Z3 1.9 Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i M Roadster M Coupe
2003-2008 E85 BMW Z4 2.5i Z4 3.0i Z4 3.0si
2009+ Z4 BMW Z4 sDrive28i Z4 sDrive30i Z4 sDrive35i Z4 sDrive35is
2000-2003 E52 BMW Z8 Roadster (without EDC)

Show More Show Less

BFI GS2 Automatic Shift Knob - Black w/ Black Perforated Air Leather ...

T#:4813287

Part#: GS2-BMA-2S

Back Ordered

$ 224.99 USD

Add to Wish List

Qty

$ 224.99 USD

Add to Wish List

Introducing the world's first Black Forest Industries shift knob specifically for Automatic transmission BMW applications. Built with the same quality materials as our other GS2 shift knobs, this application adds a control lever and internal springs to operate the automatic mechanism of a BMW shift lever.

Show More Show Less

GSP Front Wheel bearing & hub assembly - E82, E88, E90, E91, E92, E93...

T#:389674

Part#: 274254

Ships in 2 Business Days

$ 184.99 USD

Add to Wish List

Qty

$ 184.99 USD

Add to Wish List

Since established in 2004, GSP North America has positioned itself as a leading supplier of New Axles in North America.GSP’s new axle program consistently offers the best application coverage, most SKU count, and more new numbers than any other competitors. GSP’s hub assembly program was introduced to North America market in 2010 and has grown into one the most trustable programs in US market.

This item fits the following BMWs:

2008+ E82 BMW 128i 135i 135is
2006-2011 E90 BMW 325i 328i 330i 335d 335i - Sedan
2006-2012 E91 BMW 328i - Wagon
2007-2013 E92 BMW 328i 335i 335is - Coupe
2007-2013 E93 BMW 328i 335i M3 - Convertible
2013+ E84 BMW X1 sDrive28i
2009+ Z4 BMW Z4 sDrive28i Z4 sDrive30i Z4 sDrive35i Z4 sDrive35is

Show More Show Less

Maxi TPMS Kit With Sensors

T#:5663676

Part#: AULTS508K1

Ships in 6 Business Days

$ 739.99 USD

Add to Wish List

Qty

$ 739.99 USD

Add to Wish List

Pinpoint and replace bad TPMS Sensors

BFI GS2 Automatic Shift Knob - Silver w/ Red Alcantara - E82/88 E9X E...

T#:4813292

Part#: GS2-BMA-2RU

Ships on Aug 17, 2026

$ 224.99 USD

Add to Wish List

Qty

$ 224.99 USD

Add to Wish List

Introducing the world's first Black Forest Industries shift knob specifically for Automatic transmission BMW applications. Built with the same quality materials as our other GS2 shift knobs, this application adds a control lever and internal springs to operate the automatic mechanism of a BMW shift lever.

Show More Show Less

BFI GS2 Automatic Shift Knob - Silver w/ Gray Alcantara - E82/88 E9X ...

T#:4813286

Part#: GS2-BMA-2UF

Ships on Aug 17, 2026

$ 224.99 USD

Add to Wish List

Qty

$ 224.99 USD

Add to Wish List

Introducing the world's first Black Forest Industries shift knob specifically for Automatic transmission BMW applications. Built with the same quality materials as our other GS2 shift knobs, this application adds a control lever and internal springs to operate the automatic mechanism of a BMW shift lever.

Show More Show Less

MaxiBAS BT506

T#:2914145

Part#: BT506

Ships in 6 Business Days

$ 402.99 USD

Add to Wish List

Qty

$ 402.99 USD

Add to Wish List

The BT506 is a battery and electrical system analysis tool that use as Adaptive Conductance an advanced battery analysis method, to produce a more accurate examination of the battery’s cold cranking ability and reserve capacity, vital to determining a b

Show More Show Less

Receiver/Drier Canister

T#:594027

Part#: 64538375757

Ships in 1-2 days

$ 81.99 USD

Add to Wish List

Qty

$ 81.99 USD

Add to Wish List

Seatbelt 6-point Race Harness Receptacles - Macht Schnell

T#:338507

Part#: 79.20.150K

Ships on Aug 20, 2026

Starting at $ 174.00 USD

Add to Wish List

Starting at $ 174.00 USD

Add to Wish List

Many racing series and event organizers are requiring 5 or 6-point harnesses in their events now. Attaching the anchor points to the seat base is a desired alternative to drilling holes in your floor and carpet*. This set includes the 6-point anchor to attach to the Macht Schnell floor mount as well as side attachments for either a bolt-in or snap-in harness.

* - note that most racing harness manufacturers will advise that drilling through the floor is the best method for mounting harnesses. This allows you to locate the mount in the ideal location and angle to fit your driving position. The proper installation is paramount to ensure the harness works correctly in an impact.

Sold per seat.

This item fits the following BMWs:
2008-2012 E82 BMW 128i 135i 1M Coupe
1992-1998 E36 BMW 318i 318is 318ti 323is 325i 325is 328i 328is M3
1999-2005 E46 BMW 323i 323ci 325i 325ci 325xi 328i 328ci 330i 330ci 330xi M3 (not convertibles)
2006-2011 E90 BMW 325i 325xi 328i 328xi 328i xDrive 330i 330xi 335d 335i 335xi 335i xDrive M3 - Sedan
2006-2012 E91 BMW 325xi 328i 328xi 328i xDrive - Wagon
2007-2013 E92 BMW 328i 328xi 328i xDrive 335i 335is 335xi 335i xDrive M3 - Coupe
2003-2008 E85 BMW Z4 2.5i Z4 3.0i Z4 3.0si Z4 M Roadster M Coupe

Show More Show Less