BMW Z Series E85/6 (2003-2008)

Rear Shock Mounts (RSM) HP Aluminum/Rubber - E30, E36, E46, Z3, Z4 (P...

T#:3666

Part#: JTD909

Back Ordered

$ 99.99 USD

Add to Wish List

Qty

$ 99.99 USD

Add to Wish List

These are the best rear shock mounts that we have found for the E30, E36, E46, Z3 & E85 Z4! Featuring CNC-machined billet aluminum mounting base with a replaceable urethane bushing (replacement bushings are just $15 and are changed in minutes!). These mounts are excellent for either street or track because of their low NVH (noise, vibration, and harshness). Plus, the superior design will far outlast the life of stock mounts - maybe even the car itself. You'll never think twice about your shock mounts again! These shock mounts are a direct replacement of the stock mounts so they fit all shocks with the BMW-standard 10mm shock shaft, including all factory and OEM shocks (Boge, Sachs, etc), H&R coil overs, Bilstein shocks and PSS, PSS9, PSS10 coil overs (except the B16 Ride Control Kit). This is sold as a package with new shock mount gaskets, washers, and Nyloc nuts.

Must re-use factory cupped washers!

This item fits the following BMWs:
1984-1991 E30 BMW 318i 318is 318ic 325e 325es 325i 325ic 325is 325ix M3
1992-1998 E36 BMW 318i 318is 318ti 318ic 323is 323ic 325i 325is 325ic 328i 328is 328ic M3
1999-2005 E46 BMW 323i 323ci 325i 325ci 325xi 328i 328ci 330i 330ci 330xi M3
1997-2002 Z3 BMW Z3 1.9 Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i M Roadster M Coupe
2003-2008 Z4 BMW Z4 2.5i Z4 3.0i Z4 3.0si Z4 M Roadster M Coupe

Show More Show Less

KMAC Stage 1 Street Front Adjustable Camber/Caster Plates - E36, E39 ...

T#:389645

Part#: 192416-1J

In Stock

$ 380.00 USD

Add to Wish List

Qty

$ 380.00 USD

Add to Wish List

Location: Front
Type: Street, Stage 1
Bearing: captive-ball fully encased in polyurethane

These front adjustable camber/caster plates will replace your stock front upper strut bearing. The KMAC plates are a 'floating' design so camber and caster are adjusted together. This design allows maximum range of adjustment since no other hardware interferes with the adjustments. Since these replace your stock strut bearings they are designed to work with a stock-type spring only. And when installed correctly will not significantly alter ride height. Adjustment is easily done by loosening the three nuts on top of the tower and sliding the camber plate into the position you want, then re-tighten the nuts. These mounts can be installed two ways - for camber correction or swapped side-side for increasing negative camber. Detailed instructions included.

Note: suspensions vary from manufacturer to manufacturer. Turner Motorsport cannot be responsible for fitment issues caused by non-stock or specialized coil-over suspensions. As with any race-derived component, additonal fabrication may be required.

This item fits the following BMWs:
2008-2012 E82 BMW 128i 135i
6/1992-1999 E36 BMW 318i 318is 318ti 318ic 323is 323ic 325i 325is 325ic 328i 328is 328ic M3
1999-2005 E46 BMW 323i 323ci 325i 325ci 325xi 328i 328ci 330i 330ci 330xi
2006-2011 E90 BMW 325i 328i 330i 335d 335i - Sedan
2006-2012 E91 BMW 328i - Wagon
2007-2013 E92 BMW 328i 335i 335is - Coupe
2007-2013 E93 BMW 328i 335i - Convertible
1997-2003 E39 BMW 525i 528i 530i 540i (not for cars with EDC)
2004-2010 E60 BMW 525i 530i 528i 535i 545i 550i
2004-2011 E63 E64 BMW 645ci 650i
1997-2002 Z3 BMW Z3 1.9 Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i M Roadster M Coupe
2003-2008 E85 BMW Z4 2.5i Z4 3.0i Z4 3.0si
2009+ Z4 BMW Z4 sDrive28i Z4 sDrive30i Z4 sDrive35i Z4 sDrive35is
2000-2003 E52 BMW Z8 Roadster (without EDC)

Show More Show Less

Seat Floor Adapters - E36, E46, E85 - Macht Schnell

T#:300563

Part#: 79.10.101B

Ships on Aug 28, 2026

$ 235.00 USD

Add to Wish List

Qty

$ 235.00 USD

Add to Wish List

In order to mount aftermarket seats in your car, you need a floor mount adapter. These high-quality aluminum adapters are made by Macht Schnell. These bolt to your existing seat mounting studs in the floor and offer the lowest profile of any floor mount (22mm height). This helps to keep your seat at the lowest position possible. Your seat adapters or sliders bolt to this adapter plate. These floor mounts are a matrix style with rows of threaded holes that allow you to find an ideal seat location. There are other options - including homemade - but these seat brackets for your BMW are the highest quality to match your expensive seats.

Sold per seat. Can be used on left or right sides of vehicle.

These adapters were originally designed for the E46 chassis. They can fit the E36 by modifying the mounting holes to match the bolt and stud locations on the E36 floor.

This item fits the following BMWs:
1995-1999 E36 BMW 318i 318is 318ti 318i 323is 323i 325i 325is 325i 328i 328is 328i M3 (except convertibles) ( see note above )
1999-2005 E46 BMW 323i 323ci 325i 325ci 325xi 328i 328ci 330i 330ci 330xi M3 (except convertibles)
2003-2008 E85 E86 BMW Z4 2.5i Z4 3.0i Z4 3.0si Z4 M Roadster M Coupe

Show More Show Less

GSP Rear Axle Assembly - Right - E46, Z4

T#:389701

Part#: NCV27516

Ships in 2 Business Days

$ 183.99 USD

Add to Wish List

Qty

$ 183.99 USD

Add to Wish List

Since established in 2004, GSP North America has positioned itself as a leading supplier of New Axles in North America.GSP’s new axle program consistently offers the best application coverage, most SKU count, and more new numbers than any other competitors. GSP’s hub assembly program was introduced to North America market in 2010 and has grown into one the most trustable programs in US market.

This item fits the following BMWs:

E46 BMW M3

E85 BMW Z4M

Show More Show Less

GSP Rear Axle Assembly - Left - E46, Z4

T#:389714

Part#: NCV27500

Ships in 2 Business Days

$ 178.99 USD

Add to Wish List

Qty

$ 178.99 USD

Add to Wish List

Since established in 2004, GSP North America has positioned itself as a leading supplier of New Axles in North America.GSP’s new axle program consistently offers the best application coverage, most SKU count, and more new numbers than any other competitors. GSP’s hub assembly program was introduced to North America market in 2010 and has grown into one the most trustable programs in US market.

This item fits the following BMWs:

E46 BMW M3

E85 BMW Z4M

Show More Show Less

7 pc. 3/8" Dr. Spark Plug Socket Set

T#:641915

Part#: 8845D

Ships in 6 Business Days

$ 141.99 USD

Add to Wish List

Qty

$ 141.99 USD

Add to Wish List

Complete set of spark plug sockets.

Seatbelt 4-point Race Harness Receptacles - Macht Schnell

T#:338505

Part#: 79.12.15X

Ships on Aug 20, 2026

Starting at $ 125.00 USD

Add to Wish List

Starting at $ 125.00 USD

Add to Wish List

If you're going to use a 4 point racing harness with your racing or sport seat and don't want to drill through your floor and carpet, these harness adapter plates are perfect*. These sandwich in between your slider and seat bracket for a strong and secure mounting point. They are made from high-strength steel and powedercoated in stealthy black. Choose from a bolt-in or clip-in style harness end. These will only work with the Macht Schnell floor mounts.

* - note that most racing harness manufacturers will advise that drilling through the floor is the best method for mounting harnesses. This allows you to locate the mount in the ideal location and angle to fit your driving position. The proper installation is paramount to ensure the harness works correctly in an impact.

Sold per seat.

This item fits the following BMWs:
2008-2012 E82 BMW 128i 135i 1M Coupe
1992-1998 E36 BMW 318i 318is 318ti 323is 325i 325is 328i 328is M3
1999-2005 E46 BMW 323i 323ci 325i 325ci 325xi 328i 328ci 330i 330ci 330xi M3 (not convertibles)
2006-2011 E90 BMW 325i 325xi 328i 328xi 328i xDrive 330i 330xi 335d 335i 335xi 335i xDrive M3 - Sedan
2006-2012 E91 BMW 325xi 328i 328xi 328i xDrive - Wagon
2007-2013 E92 BMW 328i 328xi 328i xDrive 335i 335is 335xi 335i xDrive M3 - Coupe
2003-2008 E85 BMW Z4 2.5i Z4 3.0i Z4 3.0si Z4 M Roadster M Coupe

Show More Show Less

14 Pc. Full Polish SAE Angle Head Wrench Set

T#:642035

Part#: 9914A

Ships on Aug 17, 2026

$ 113.91 USD

Add to Wish List

Qty

$ 113.91 USD

Add to Wish List

Radius V-Groove design creates an anti-slip while also preventing round-off.

KMAC Stage 2 Street/Track Front Adjustable Camber/Caster Plates - E36...

T#:389647

Part#: 192416-2L

Special Order: No Guaranteed ETA

$ 545.00 USD

Add to Wish List

Qty

$ 545.00 USD

Add to Wish List

Location: Front
Type: Street/Track, Stage 2
Bearings: main PTFE-lined pillow-ball bearing suspended in polyurethane; self-lubricating radial axial bearing/bushing in upper spring plate
Springs: includes OEM size upper spring perch, 60mm upper spring perch, and 2.5" upper spring perch

The Stage 2 KMAC plates are a mixed track and street camber/caster plate meant to be used in a variety of suspensions and setups. Since there is less bushing than on the Stage 1, more noise and vibration will reach the driver. The adjustment design is similar to the Stage 1 with a floating mount that sets camber and caster simultaneously. This design allows maximum range of adjustment since no other hardware interferes with the adjustments. These plates can work on both coil over and stock-stype suspensions and upper spring perches are included for OEM springs, 60mm, and 2.5" coil over springs. The upper perch assembly incorporate a self-sliding radial bushing that allows the spring to spin during its travel instead of bind. This reduces tension on the spring and helps reduce noise and spring 'popping' noises. Bearing inserts, spacers for correct articulating angles, and 3 sizes of upper nut adapters included. The urethane bushings and bearings are replaceable if they wear out. These are designed mainly for adding negative camber for improved handling and not for camber correction back to stock settings (see Stage 1 kit). Basic instructions included but professional installation is required.

Note: suspensions vary from manufacturer to manufacturer. The proper stacked height and clearances are required. K-Mac includes bearing adapters, spacers, and various top nuts but it is still the responsibility of the installer to ensure a correct and safe fitment. As with any race-derived component, additonal fabrication may be required.

This item fits the following BMWs:
2008-2012 E82 BMW 128i 135i
6/1992-1999 E36 BMW 318i 318is 318ti 318ic 323is 323ic 325i 325is 325ic 328i 328is 328ic M3
1999-2005 E46 BMW 323i 323ci 325i 325ci 325xi 328i 328ci 330i 330ci 330xi
2006-2011 E90 BMW 325i 328i 330i 335d 335i - Sedan
2006-2012 E91 BMW 328i - Wagon
2007-2013 E92 BMW 328i 335i 335is - Coupe
2007-2013 E93 BMW 328i 335i - Convertible
1997-2003 E39 BMW 525i 528i 530i 540i (not for cars with EDC)
2004-2010 E60 BMW 525i 530i 528i 535i 545i 550i
2004-2011 E63 E64 BMW 645ci 650i
1997-2002 Z3 BMW Z3 1.9 Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i M Roadster M Coupe
2003-2008 E85 BMW Z4 2.5i Z4 3.0i Z4 3.0si
2009+ Z4 BMW Z4 sDrive28i Z4 sDrive30i Z4 sDrive35i Z4 sDrive35is
2000-2003 E52 BMW Z8 Roadster (without EDC)

Show More Show Less

KMAC Stage 3 Street/Track Front Adjustable Camber/Caster Plates - E36...

T#:389646

Part#: 192416-3L

Special Order: No Guaranteed ETA

$ 545.00 USD

Add to Wish List

Qty

$ 545.00 USD

Add to Wish List

Location: Front
Type: Street/Track, Stage 2
Bearings: main PTFE-lined pillow-ball bearing suspended in polyurethane; self-lubricating radial axial bearing/bushing in upper spring plate
Springs: includes OEM size upper spring perch, 60mm upper spring perch, and 2.5" upper spring perch

The Stage 3 KMAC plates are a mixed track and street camber/caster plate meant to be used in a variety of suspensions and setups. Since there is less bushing than on the Stage 1, more noise and vibration will reach the driver. The adjustment design is similar to the Stage 1 with a floating mount that sets camber and caster simultaneously. This design allows maximum range of adjustment since no other hardware interferes with the adjustments. These plates can work on both coil over and stock-stype suspensions and upper spring perches are included for OEM springs, 60mm, and 2.5" coil over springs. The upper perch assembly incorporate a self-sliding radial bushing that allows the spring to spin during its travel instead of bind. This reduces tension on the spring and helps reduce noise and spring 'popping' noises. Bearing inserts, spacers for correct articulating angles, and 3 sizes of upper nut adapters included. The urethane bushings and bearings are replaceable if they wear out. These are designed mainly for adding negative camber for improved handling and not for camber correction back to stock settings (see Stage 1 kit). Basic instructions included but professional installation is required.

Note: suspensions vary from manufacturer to manufacturer. The proper stacked height and clearances are required. K-Mac includes bearing adapters, spacers, and various top nuts but it is still the responsibility of the installer to ensure a correct and safe fitment. As with any race-derived component, additonal fabrication may be required.

This item fits the following BMWs:
2008-2012 E82 BMW 128i 135i
6/1992-1999 E36 BMW 318i 318is 318ti 318ic 323is 323ic 325i 325is 325ic 328i 328is 328ic M3
1999-2005 E46 BMW 323i 323ci 325i 325ci 325xi 328i 328ci 330i 330ci 330xi
2006-2011 E90 BMW 325i 328i 330i 335d 335i - Sedan
2006-2012 E91 BMW 328i - Wagon
2007-2013 E92 BMW 328i 335i 335is - Coupe
2007-2013 E93 BMW 328i 335i - Convertible
1997-2003 E39 BMW 525i 528i 530i 540i (not for cars with EDC)
2004-2010 E60 BMW 525i 530i 528i 535i 545i 550i
2004-2011 E63 E64 BMW 645ci 650i
1997-2002 Z3 BMW Z3 1.9 Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i M Roadster M Coupe
2003-2008 E85 BMW Z4 2.5i Z4 3.0i Z4 3.0si
2009+ Z4 BMW Z4 sDrive28i Z4 sDrive30i Z4 sDrive35i Z4 sDrive35is
2000-2003 E52 BMW Z8 Roadster (without EDC)

Show More Show Less

GSP Front Wheel bearing & hub assembly - E82, E88, E90, E91, E92, E93...

T#:389674

Part#: 274254

Ships in 2 Business Days

$ 184.99 USD

Add to Wish List

Qty

$ 184.99 USD

Add to Wish List

Since established in 2004, GSP North America has positioned itself as a leading supplier of New Axles in North America.GSP’s new axle program consistently offers the best application coverage, most SKU count, and more new numbers than any other competitors. GSP’s hub assembly program was introduced to North America market in 2010 and has grown into one the most trustable programs in US market.

This item fits the following BMWs:

2008+ E82 BMW 128i 135i 135is
2006-2011 E90 BMW 325i 328i 330i 335d 335i - Sedan
2006-2012 E91 BMW 328i - Wagon
2007-2013 E92 BMW 328i 335i 335is - Coupe
2007-2013 E93 BMW 328i 335i M3 - Convertible
2013+ E84 BMW X1 sDrive28i
2009+ Z4 BMW Z4 sDrive28i Z4 sDrive30i Z4 sDrive35i Z4 sDrive35is

Show More Show Less

Seatbelt 6-point Race Harness Receptacles - Macht Schnell

T#:338507

Part#: 79.20.150K

Ships on Aug 20, 2026

Starting at $ 174.00 USD

Add to Wish List

Starting at $ 174.00 USD

Add to Wish List

Many racing series and event organizers are requiring 5 or 6-point harnesses in their events now. Attaching the anchor points to the seat base is a desired alternative to drilling holes in your floor and carpet*. This set includes the 6-point anchor to attach to the Macht Schnell floor mount as well as side attachments for either a bolt-in or snap-in harness.

* - note that most racing harness manufacturers will advise that drilling through the floor is the best method for mounting harnesses. This allows you to locate the mount in the ideal location and angle to fit your driving position. The proper installation is paramount to ensure the harness works correctly in an impact.

Sold per seat.

This item fits the following BMWs:
2008-2012 E82 BMW 128i 135i 1M Coupe
1992-1998 E36 BMW 318i 318is 318ti 323is 325i 325is 328i 328is M3
1999-2005 E46 BMW 323i 323ci 325i 325ci 325xi 328i 328ci 330i 330ci 330xi M3 (not convertibles)
2006-2011 E90 BMW 325i 325xi 328i 328xi 328i xDrive 330i 330xi 335d 335i 335xi 335i xDrive M3 - Sedan
2006-2012 E91 BMW 325xi 328i 328xi 328i xDrive - Wagon
2007-2013 E92 BMW 328i 328xi 328i xDrive 335i 335is 335xi 335i xDrive M3 - Coupe
2003-2008 E85 BMW Z4 2.5i Z4 3.0i Z4 3.0si Z4 M Roadster M Coupe

Show More Show Less