Sensors for BMW Z Series E85/6 (2003-2008)

All vehicles will lose some degree of performance due to heat soak under the right operating conditions.  Engine management systems constantly monitor operating conditions and modifying parameters based on sensor inputs. BMW integrated the intake air temp sensor in the MAF housing on models such as the E39 M5, and, being sandwiched behind a hot radiator and in some applications next to an even hotter valve cover, this is less than ideal for performance applications. Absorbing excess heat from its surroundings, the MAF can’t shed it fast enough, and the ECU reads an inaccurately high intake air temperature. Compensating for this false hot air measurement, the ECU pulls timing and runs a richer fuel mixture, resulting in a significant loss of torque.

What can you do?  Locate an intake air temp sensor in a location where it can properly measure incoming air temps and where it's less prone to heat soak. Mounting the sensor further away from the heat source and isolating it from the MAF housing, it can both resist the effects of heat soak longer and respond to temperature changes more quickly.  The result is you’ll experience reduced torque loss and more consistent power output when you’re pushing your engine hard. 

The Turner engineering team was initially skeptical of the claimed performance benefits of this modification. They first set out validate the functionality and performance benefit of a temp sensor relocation. Replicating stop-and-go traffic heat soak in a 2001 540i was a simple task in a controlled environment - their dynometer. First the car was heat soaked to simulate being stuck in traffic or moving at low speeds by running the car four times on the dyno with the dyno's cooling fans disabled. The fans were then turned on for three more runs to observe the recovery rate once air flow was reintroduced. The test: following this procedure once with a stock IAT, and once with their relocation kit in place. 

The result? Turner recovered 11lb-ft torque at 2500rpm through use of their relocation kit, with even greater recovery to be found for M5 owners. Here are the heat soak-related torque losses Turner experienced:

Stock IAT location:
18rwtq at 2500rpm
10rwtq at 3000rpm
9rwtq at 3700rpm

Turner IAT Relocation:
7rwtq at 2500rpm
5rwtq at 3000rpm
5rwtq at 3700rpm

**Click here for installation instructions**

The Turner engineering team designed a complete plug and play kit (unlike all other options on the market) that makes for quick, easy, and reversible installation. Weather-sealed connectors keep out the elements, while sheathed wiring offers a clean appearance underhood. With a harness nearly 3 feet long - the Turner IAT relocation kit offers flexibility in positioning, but not too long that you're left with unsightly excess wiring. Turner recommends positioning the sensor in a location away from engine heat, but still within the intake ducting to achieve accurate intake temp readings - such as the far side of the base of the airbox. Vehicles with cold air intakes with cone-style filters can even position the sensor in the end of the filter. Simply drill a hole in your (cool) location of choice and plug in the harness. More information including installation instructions and some good examples of sensor mounting locations can be found in our DIY PDF. 

We include everything you need to relocate your IAT, just select your desired sensor brand below - Genuine BMW or original equipment Beru.

Also the perfect plug-n-play option for anyone looking to upgrade their intake to utilize an Alpha-N tune!

Note for vehicles with M62 engine: applicable to 1999 and up

The eccentric shaft sensor plays a vital role in controlling valvetronic timing and is often a common issue in BMW vehicles. If you've noticed difficult starts, reduced fuel economy, and overall engine power and performance issues, this component could be the culprit.

Key Features:

Guaranteed Fitment: Designed to fit perfectly, ensuring compatibility with your vehicle. Accurate Positioning: Provides precise shaft position control, even at high RPMs. Direct OE Replacement: Easy to install with its direct-fit design, saving time and effort. Low Electrical Resistance: Alloy connector conductors minimize resistance, ensuring accurate signal transmission. Upgrade to this quality replacement eccentric shaft sensor to restore optimal engine performance and address the symptoms associated with a faulty sensor.

URO Camshaft Position Sensor is a premium replacement component specifically designed for BMW vehicles, ensuring optimal engine performance and reliability. Manufactured by Turner Motorsport, this camshaft position sensor plays a crucial role in maintaining accurate timing and enhancing overall engine efficiency. By upgrading to the URO Camshaft Position Sensor, BMW owners can expect improved engine responsiveness and a significant reduction in potential diagnostic trouble codes.

• Enhanced Engine Performance: Ensures precise timing and efficient engine operation, contributing to superior overall performance.
• Durable Construction: Crafted from high-quality materials that withstand extreme conditions for long-lasting durability.
• Easy Installation: Designed for a direct fit, facilitating straightforward installation for both professionals and DIY enthusiasts.
• Reliable OEM Replacement: Matches OEM specifications, providing peace of mind and preserving the integrity of the vehicle.