BMW Engine Parts for BMW Z Series E85/6 (2003-2008)

Rally Road Productions, Inc. is a team supported by a group of people with great abilities in their area of expertise. From the "web guy" and driving instructor friends, to owners of various machine shops, they have surrounded ourselves with people that can be trusted to create and manufacture quality products. This is the key to ensuring everything that they sell will perform as it was intended. The goal is to increase customer satisfaction and make the customization or performance enhancement of your vehicle a more enjoyable venture.

This oil cooler system is race tested and proven to outflow the euro M3 oil filter housing. Additionally, this particular system uses a sealing mechanism to direct the oil flow through the cooler lines and then through the oil filter.  Other cooler caps do not provide this seal and therefore the external oil coolers and lines act as a "balloon".  The lines and cooler are pressurized, but oil does not flow through them.  Flowing oil means it is being cooled and not just acting as an external reservoir.

Flow testing reveals that the oil cooler cap will outflow the Euro M3 Oil Filter Housing by more than 80% at the same, pressure, RPM, and oil temperature. In the upper RPM range, there is nearly a 100% improvement in flow from the RallyRoad oil cooler cap when compared to the Euro M3 oil filter housing.  This is a massive improvement over OE and is a worthwhile upgrade, especially in engines that see severe duty.

Features:

• -8AN o-ring ports to provide a leak free fitting without the use of Teflon tape or sealant used by other oil cooler caps.
• Viton o-rings are used throughout to maintain function and sealing in a high-temperature oil environment.
• Use of the stock filter cap bolt to reduce cost and simplify installation.
• An internal sealing mechanism to direct oil flow through the oil cooler and through the filter.
• 1/8" NPT side port for external oil pressure gauge.

Kit Includes:

• Oil filter cap with fittings
• Oil filter sealing ring
• BMW MANN Oil Filter and gasket

This part fits the following BMWs
1992-1999 E36 323i 325i 325is 328i 328is

If you're not sure if your Vanos seals are bad then the only question you need to answer is if you've replaced them. Every unit from the factory came with the same failure prone o-rings and seals, even the re-manufactured units you can still get today. The only real fix is by replacing the seals and o-rings with material that is built to last in the oiled, extreme temperature environment found in these kits. 

A premium product replacement with easy to follow instructions makes rebuilding your Vanos unit a must. Even thought the power loss is barely felt it's the opposite result once you replace the seals, every car that gets rebuilt ends up wowing the customer and all of them saying they didn't realize what they lost. 

There are a number of symptoms that will plague your car as a result of these failing seals such as erratic idle, engine hesitation, stalling, and increased fuel consumption to name a few. If you've been chasing down any of these symptoms with no fix then this could be your issue.

While you 're replacing the seals in your Vanos unit it a good time to install anti-rattle spacers to tighten up the gaps in your stock assembly and get rid of that noisy Vanos clatter.

Rebuild instructions : http://bd8ba3c866c8cbc330ab-7b26c6f3e01bf511d4da3315c66902d6.r6.cf1.rackcdn.com/PDF_12017_BMW_M5X_Dual_Vanos_Rebuild_Kits.pdf

This item fits the following BMWs: 

1999-2005 E46 BMW 323i 323ci 325i 325ci 325xi 328i 328ci 330i 330ci 330xi 
1999-2003 E39 BMW 525i 528i 530i 
2004-2010 E60 BMW 525i 530i 
2004-2006 E83 BMW X3 2.5i X3 3.0i 
2000-2006 E53 BMW X5 3.0i 
1999-2002 Z3 BMW Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i 
2003-2005 Z4 BMW Z4 2.5i Z4 3.0i 

Still looking for more power after bolt-ons? High performance camshafts from Schrick are the way to go. These cams are a direct replacement for the stock cams and give a solid 15+ horsepower boost at the top end and great midrange torque increases too! More gains can be expected with intake and header upgrades and custom software tuning. A slightly lumpy idle is expected at cold start but will be smooth once at operating temperature. This set is just a great all-around cam upgrade for the S54!

These Schrick cams were initially developed for the M3 CSL but they also work great on the US and other non-CSL S54 engines as well. With more duration they are a great match to high flow headers, no cats, or CSL intake manifold upgrades. These are the new "cast" cams from Schrick which require new rocker arms (Schrick recommended or BMW part #11337833259). Professional installation is a must due to the intricacies with the double VAN0S.

Schrick Technical Information / Specs

This item fits the following BMWs:

• 2001-2006 E46 BMW M3
• 2001-2002 Z3 BMW M Roadster M Coupe
• 2006-2008 E85 BMW Z4 M Roadster M Coupe