BMW Engine Parts for BMW 3 Series E90 (2006-2011)

Upgrade your stock oil cooler thermostat for improved performance. Swap your factory 110-degree Celsius thermostat for a new 70-degree Celsius version for faster oil flow and extended temperature control. With oil temperatures reaching 230 degrees Fahrenheit by the time your factory thermostat opens, initiating oil flow at lower temperatures proves more effective than attempting to cool down already elevated temperatures.

Utilizing a factory-style thermostat, this upgrade can be used in all weather conditions and allows your engine to warm up properly, unlike thermostat bypass kits.

Kit contents:​

Lower temperature thermostat - 70c (158F) vs Factory 110c (230F)
Low temp thermostat spring

Ensure proper sealing when installing the turbos on your N54.

Kit includes:

• 16 - ASA M7x39 studs
• 16 - Flange nuts
• All required gaskets and o-rings
• Water pump install hardware
• Replacement vacuum hose
• T-bolt clamps

Helpful hints:

For complete installation instructions, refer to Haynes Service Manual (T#193950).

Both downpipes must be removed to remove either front or rear turbo. Tie rod end may need to be separated from knuckle for clearance. Steering rack may also need to be rotated away from subframe for access. Valve cover heat shield will need to loosened and pushed upward to get clearance for turbo manifold removal.

If studs back out of cylinder head and nuts are seized to studs, replace studs. Thread studs in to head by hand to prevent cross threading. When installing the new studs in the cylinder head, use a high temperature loctite in the cylinder head side, and copper anti-seize on the nut side.

To make more room for access to the front turbo, remove the rubber line running in front of the subframe that attaches to the back of the map thermostat and remove the clip. Cut off the OEM clamp and replace it with a new hose clamp as well.

Complete removal of the water pump is not required. Detach the water pump from the side of the block and push it out of the way to make more room for access to the front turbo. If water pump is unbolted from the block, the aluminum bolts must be replaced.

Torque specs:
Bracket to cylinder head: 9Nm
Coolant supply line to crankcase: 9Nm
Coolant return line to crankcase: 8Nm
Coolant return line to turbo: 8Nm
Coolant supply line to supply line: 8Nm
Exhaust manifold heat shield: 8Nm
Oil supply line to crankcase: 20Nm
Oil pressure line to turbo: 8Nm
Oil return line to crankcase: 8Nm
Oil return line to turbo: 8Nm
Turbo manifold to head: 20Nm

BMW M57 Diesel Crank Pulley Turning Tool is essential for precise handling and adjustment of the crankshaft pulley in BMW diesel engines, including the N47, N57, and M57 models. This high-quality tool ensures accurate turning of the crankshaft pulley, facilitating easier maintenance and repairs.

• Precision Engineering: Designed specifically for BMW M57 diesel engines for accurate pulley adjustment.
• Compatibility: Fits various BMW diesel engines including N47, N57, and M57 models.
• Durable Construction: Built to withstand the demands of automotive maintenance and repair.
• Enhanced Efficiency: Simplifies crankshaft pulley turning, making engine service tasks more straightforward.

For a comprehensive tool kit, search for T#23913947.

BMW M57 Diesel Injection Pump Puller is an essential tool designed specifically for removing injectors from BMW M47 and M57 diesel engines. Engineered for precision and durability, this puller facilitates the efficient extraction of diesel injectors without causing damage to the engine components. It is a must-have for any professional mechanic or DIY enthusiast working on BMW diesel engines.

• Efficient Extraction: Removes diesel injectors with ease, reducing labor time.
• Precision Engineering: Designed specifically for BMW M47 and M57 diesel engines.
• Durable Construction: Built to withstand the rigors of frequent use.
• Protects Engine Components: Minimizes the risk of damage during injector removal.

This kit includes every thing needed to replace your rod bearings.

Kit includes

Upper and lower WPC-treated rod bearings Hardware Oil filter BMW TwinPower Turbo Oil Oil pan gasket RedLine assembly lube

Looking to update your old torque wrenches? The Schwaben 3/8" Drive Digital Torque Wrench is your answer. 

This digital torque wrench uses an easy-to-read display to show torque amounts and settings, features a push button release, reversible 3/8" drive, 45 tooth ratchet head, and a comfortable no-slip grip and adjustment wheel.

Specifications:

• Setting Range: 45-220 ft lbs (60-300 Nm)
• Display Units: ft-lbs, N-m, Inch-lbs, cm-kg2, and m-kg
• Size: 22" (550mm) length for easy leverage
• Accuracy: +- 3%
• Include blow molded holding case
• Requires one 3V CR2030 battery (included)

Discover the ultimate solution for your MINI Cooper's N12, N14, N16, and N18 engines in the R56 chassis – our MINI Cooper Front Crankshaft Seal Installer. This tool simplifies the installation process effortlessly. Just follow these easy steps: Tighten the three inner bolts to attach the inner piece onto the front crankshaft. Then, insert the seal into the outer portion of the tool. Place the outer portion over the now-attached stud and utilize the included pushing nut to apply uniform pressure, securely seating the seal onto the front crankshaft.

Crafted from robust materials, this tool is indispensable for both mechanics and DIY enthusiasts. Say farewell to laborious manual installations and welcome a quick, precise solution into your automotive toolkit. Upgrade your equipment today and make perfect seal installations a breeze.

This tool will also work on select BMW engines, please check fitment by entering your vehicle information!