BMW Engine Parts for BMW 7 Series F02 (2009+)

Clear BMW chassis

Please ensure your correct model is selected

Turner Motorsport has everything you need to upgrade your BMW through our stages of performance or to keep your car in peak condition with our range of the latest in proven OEM cooling parts. Upgrade your cooling system and engine performance with the selections below to give your BMW a performance and reliability advantage.

Sub-Categories

Sort By:

Bosch - Corporate Logo
T#:588121
Part#: 12138616153
In Stock
$ 34.99 USD
Free Shipping on orders $49 and up
Sluggish acceleration, misfires, and rusty terminals are symptoms of a worn coil. Located on the top of your engine, these coils should be inspected and replaced as needed or every 100,000 miles. Keep your ignition system in perfect order. Rubber integrated boot and snap-top cap. OEM Bosch Part Number: 0221504800
Show More Show Less
Elring Valve Cover Gasket Set - N55 3.0L, S55
2X Entries Into Our F80 M3 Sweepstakes
Elring - Corporate Logo
T#:399889
Part#: 11127587804
In Stock
$ 31.79 USD
Free Shipping on orders $49 and up
If there is a large amount of oil on the sides of the engine or if you can smell burning oil, chances are it's a bad valve cover gasket. The gasket fails and allows oil to seep down onto the side of the engine and other parts causing a mess and reducing the amount of oil in your engine. This replacement gasket from Elring is perfect to prevent any further oil leaks.
Show More Show Less
OEM Elring Oil Pan Gasket - BMW N52 N55 3.0L
2X Entries Into Our F80 M3 Sweepstakes
Elring - Corporate Logo
T#:2602231
Part#: 11137600482
In Stock
$ 31.79 USD
Free Shipping on orders $49 and up
Metal/rubber gasket used to stop oil leaks, seals the oil pan to the engine block

VTT S55 Crank Bolt Capture - F8X S55 F3x N55
2X Entries Into Our F80 M3 Sweepstakes
Vargas Turbo Technologies - Corporate Logo
T#:557934
Part#: VTT-S55-CBC
In Stock
$ 129.99 USD
Free Shipping
$ 129.99 USD
Free Shipping
The S55 suffers from a weak point in its crankshaft. It has been reported that when increasing the power to the engine, the crank hub can move or spin slightly under an extreme load.

Bosch - Corporate Logo
T#:340644
Part#: 12137594937
In Stock
$ 30.99 USD
Free Shipping on orders $49 and up
$ 30.99 USD
Free Shipping on orders $49 and up

 

This is the OEM Bosch ignition coil that is the current replacement for most BMW 6 and 8-cylinder engines built since 2003. It's listed as a replacement coil for M54, M56, S54, N52, N54, N62, N63, N73, S63, S63TU and other engines. BMW has made numerous changes to ignition coil part numbers in recent years but has approved this part number to work in the vehicles listed in our fitments tab. This part number replaces previous BMW part numbers 12130390064, 12130148594, 12131712219, and 12137551260.

Ignition coils are key to the efficiency and performance of your BMW. With a faulty coil the spark plug is not burning the air/fuel mixture properly and that can lead to problems anywhere in the engine and exhaust (including catalytic converters and O2 sensors). Problems with one or more coils will cause a fault code but not always a check engine light. A misfire code may be related to an ignition coil but could be from other things as well. Sometimes a visual inspection of a coil and coil boot will give an indication of a failure. You can also move coils around to different cylinder banks to see if the misfire code follows a suspect coil. We suggest always having one or two coils on hand to keep as spares.

This Bosch part also satisfies BMW's service bulletin for 2001-2003 E46 M3 ignition coils (SIB 12 24 05). That SIB calls for Bremi or ERA brand coils but BMW has replaced them with this Bosch design.

Bosch is one of the largest OEM producers of Genuine BMW and aftermarket parts in the world, providing parts for almost every major automotive manufacturer. Bosch has likely supplied many of the original electrical (and mechanical) parts for your BMW. Thanks to their quality, high durability, and reliability, you should expect a long service life from Bosch products.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

Sold per coil. Includes connecting boot.

Show More Show Less
OEM Bosch High Pressure Fuel Injector - EU5 - N63 S63 4.4L
For vehicles with a production date up to 07/2013
Bosch - Corporate Logo
T#:594993
Part#: 13647599876
In Stock
$ 94.99 USD
Free Shipping
$ 94.99 USD
Free Shipping

Enhance engine performance and driveability in your BMW 4.4L N63/S63 with the Bosch Fuel Injector. Replace those old, dirty, high mileage fuel injectors with this specifically designed component from Bosch. Priced individually, this fuel injector ensures optimal fuel delivery, restoring efficiency to your BMW's engine.

  • Restores engine performance
  • Enhances driveability
  • Specifically designed for BMW 4.4L N63/S63 engines
  • Replaces old, dirty, high mileage fuel injectors
  • Ensures optimal fuel delivery
  • Priced individually for cost-effective replacement
  • High-quality Bosch brand reliability
Show More Show Less

Bosch - Corporate Logo
T#:596687
Part#: 13538627842
In Stock
$ 139.99

This product was last offered at the strikethrough price on
08-14-2026

$ 102.99 USD
Free Shipping
$ 102.99 USD
Free Shipping
Replace your clogged or leaking injector to restore smooth engine operation!
Vargas Turbo Technologies - Corporate Logo
T#:558084
Part#: VTT-CRANK-BREATH
In Stock
$ 129.99 USD
Free Shipping
$ 129.99 USD
Free Shipping

VTT is happy to introduce the first and only available plug and play crankcase breather kits for ALL BMW applications that use the two-prong oil tab style oil fill caps. With this breather simply remove your oil cap, install the breather, and instantly free up horsepower, improve turbo draining, remove crankcase pressure, all while adding a cool look to your engine bay.

Can be used by itself with the stock PCV system to eliminate crankcase pressure, or with any number of PCV setups for the ultimate in crankcase pressure relieve 

Made from 6061-T6 Aircraft aluminum anodized black for a long-lasting finish, 4 stainless steel baffles for complete oil control, a PTFE one way check ball, a high-quality filter, and clamp all work together to keep crankcase pressure where it belongs, out of your crankcase.

This breather will fit:
 ALL BMW's with the two-prong style oil fill cap including but not limited to N54, N55, S55, S54

NOTE: NOT ALL THE MODELS LISTED HAVE THE SAME HOOD CLEARANCE, WE CANNOT SAY WHICH MODELS WILL HAVE CLEARANCE ISSUES, AND WHICH WILL NOT AS WE HAVE NOT TEST IT ON ALL MODELS. IF YOU ARE ORDERING THE BREATHER FOR ANYTHING OTHER THAN AN N54 TEST CLOSE YOUR HOOD CAREFULLY TO ENSURE CLEARANCE IF IT DOES NOT FIT LET US KNOW, AND WE WILL GET YOU A REFUND ONCE THE BREATHER IS RETURNED.

MODEL LIST OF REPORTED CLEARANCE ISSUES: N55 E/F 3 SERIES

Show More Show Less

Bosch - Corporate Logo
T#:19449
Part#: 16137193479
In Stock
$ 68.99 USD
Free Shipping
$ 68.99 USD
Free Shipping
Replace the defective leak diagnosis pump -often referred to as the "DTML pump" - on your BMW with this OEM unit from Bosch. This part detects vapor leaks in the fuel evaporative system.

This item fits the following BMWs:
2008+ E82 BMW 128i 135i 135is 1M Coupe
2002-2005 E46 BMW 325i 325ci 325xi 330i 330ci 330xi M3
2006-2011 E90 BMW 325i 325xi 328i 328xi 328i xDrive 330i 330xi 335i 335xi 335i xDrive M3 - Sedan
2006-2012 E91 BMW 325xi 328i 328xi 328i xDrive - Wagon
2007-2013 E92 BMW 328i 328xi 328i xDrive 335i 335is 335xi 335i xDrive M3 - Coupe
2007-2013 E93 BMW 328i 335i M3 - Convertible
2002-2003 E39 BMW 525i 528i 530i 540i M5
2004-2010 E60 BMW 525i 525xi 530i 530xi 528i 528xi 528i xDrive 535i 535xi 535i xDrive 545i 550i M5
2010-3/2012 F07 BMW 535i GT, 535i xDrive GT, 550i GT, 550i xDrive GT
3/2012+ F07 BMW 550i GT, 550i xDrive GT
2011-3/2012 F10 BMW 528i (N52) 528i xDrive 535i 535i xDrive 550i 550i xDrive
3/2012+ F10 BMW 550i 550i xDrive
2004-2010 E63 BMW 645ci 650i M6
2012-3/2012 F12 BMW 640i 650i 650i xDrive
3/2012+ F12 BMW 650i 650i xDrive
2002-2006 E65 BMW 745i 745li 750i 750li 760i 760li
2009+ F01 BMW 740i 740li 750i 750li 750i xDrive 750li xDrive
2013+ E84 BMW X1 sDrive28i X1 xDrive28i X1 xDrive35i
2004-2010 E83 BMW X3 2.5i X3 3.0i X3 3.0si
2011 F25 BMW X3 xDrive28i
2011+ F25 BMW X3 xDrive35i
2002-2006 E53 BMW X5 3.0i X5 4.4i X5 4.6is X5 4.8is
2007-2013 E70 BMW X5 3.0si X5 4.8i X5 xDrive30i X5 xDrive35i X5 xDrive48i X5 xDrive50i X5M
2008+ E71 BMW X6 xDrive35i X6 xDrive50i X6M
2002-2002 Z3 BMW Z3 2.5i Z3 3.0i M Roadster M Coupe
2003-2008 E85 BMW Z4 2.5i Z4 3.0i Z4 3.0si Z4 M Roadster M Coupe
2009+ Z4 BMW Z4 sDrive28i Z4 sDrive30i Z4 sDrive35i Z4 sDrive35is
2002-2003 E52 BMW Z8 Roadster
Show More Show Less

Bosch - Corporate Logo
T#:399809
Part#: 13537622231
In Stock
$ 79.00 USD
Free Shipping on orders $49 and up
This sensor monitors the pressure of the fuel coming from the high pressure fuel pump, looking for low pressure, to determine if your HPFP is functioning correctly.
OEM Bosch Fuel Injector - EU6 Designation - N20/26 N55
For vehicles with production date from 07/2013
Bosch - Corporate Logo
T#:585581
Part#: 13648625397
In Stock
$ 133.99

This product was last offered at the strikethrough price on
06-22-2026

$ 109.99 USD
Free Shipping
$ 109.99 USD
Free Shipping
Replace your clogged or malfunctioning fuel injector with this Genuine BMW injector to restore proper engine idling and running conditions. Ensure that you need injector with EU6 designation before purchase. This fuel injector will not work with earlier EU5 version fuel rails and injector; non-exchangeable Replaces Genuine BMW part # 13648625397 and requires BMW part # 13537577649 for installation.
Show More Show Less
Elring Valve Cover Gasket - N54 3.0L
2X Entries Into Our F80 M3 Sweepstakes
Elring - Corporate Logo
T#:362693
Part#: 11127565286
In Stock
$ 36.99 USD
Free Shipping on orders $49 and up

If there is a large amount of oil on the sides of the engine or if you can smell burning oil, chances are it's a bad valve cover gasket. The gasket fails and allows oil to seep down onto the side of the engine and other parts causing a mess and reducing the amount of oil in your engine. This replacement gasket from Elring is perfect to prevent any further oil leaks.

Elring is one of the biggest OEM names in the manufacturing of high quality gaskets that are available for very affordable prices. Elring has supplied many automotive names for years with the gaskets that seal your car's components from day 1 so you can rest assured that these components will last for a long time to come!

Fits the following BMW engines:
N54 3.0L

Show More Show Less


N54 & E8x/E9x N55 Mosselman Billet Oil Thermostat
For Gasket/Install kit see T#4799665
Mosselman Turbosystems - Corporate Logo
T#:4621131
Part#: OTN54.T85
In Stock
$ 379.99 USD
Free Shipping
$ 379.99 USD
Free Shipping
The N54 engine is no stranger to oil cooling problems, that’s why we recommend installing the MSL Oil Thermostat. The standard oil thermostat will reach around 120 degrees Celsius with a normal driving style. The MSL Oil Thermostat will open at a lower temperature than the standard oil thermostat (at 85 degrees Celsius) and will keep the temperature stable between 95 and 105 degrees Celsius. Installing the MSL thermostat ensures a cooler oil temperature which will result in more stable performance, but above all this improves the reliability of the engine. It is recommended to install the thermostat, especially for cars that are tuned.
Show More Show Less
Elring Oil Pan Gasket - N52 N54 3.0L
2X Entries Into Our F80 M3 Sweepstakes
Elring - Corporate Logo
T#:376168
Part#: 11137548031
In Stock
$ 37.99

This product was last offered at the strikethrough price on
10-26-2026

$ 37.59 USD
Free Shipping on orders $49 and up
$ 37.59 USD
Free Shipping on orders $49 and up

If oil is leaking from the seal at the oil pan and block, you will need a new oil pan gasket. It is also wise to change this any time you have to pull the oil pan gasket.

Elring is one of the biggest OEM names in the manufacturing of high quality gaskets that are available for very affordable prices. Elring has supplied many automotive names for years with the gaskets that seal your car's components from day 1 so you can rest assured that these components will last for a long time to come!

Fits the following BMW engines:
N52 3.0L
N54 3.0L

Show More Show Less
N55 Valve Cover OEM Elring
2X Entries Into Our F80 M3 Sweepstakes
Elring - Corporate Logo
T#:2438603
Part#: 11127570292
In Stock
$ 436.99

This product was last offered at the strikethrough price on
05-12-2026

$ 289.99 USD
Free Shipping
$ 289.99 USD
Free Shipping
Complete assembly with gaskets & hardware

VTT N54 Crank Bolt Capture - N54
2X Entries Into Our F80 M3 Sweepstakes
Vargas Turbo Technologies - Corporate Logo
T#:557938
Part#: VTT-N54-CBC
In Stock
$ 129.99 USD
Free Shipping
$ 129.99 USD
Free Shipping

The N54 suffers from a weak point in its crankshaft. It has been reported that when increasing the power to the engine, the crank hub can move or spin slightly under an extreme load. This is most apparent under high-rev downshifts or in the case of increased boost pressure which creates more stress on the engines rotating assembly. In order to keep this from happening, the crank bolt must be secured to the hub to keep it from backing off, but this can be a tricky solution since a simple dab of Loctite will not suffice. 

Here is an easy, and cost-effective way to secure the situation; The VTT N54 crank bolt capture. This lightweight and durable ring slips over the head of the crank bolt fully encapsulating it, and locks it to the crank hub and eliminating its ability to spin. The VTT-CBC is 100% Billet Aircraft Grade Aluminum, Anodized black to protect it from the elements, and give it a stealth look. What's more is that it weighs only 1.3 Oz's meaning you aren't adding excess mass to the crankshaft which will avoid any imbalance or vibration issues.

While this is not a full fix for all crank hub spinning issues, the engineers at Vargas have found most issues have stemmed from the bolt itself backing out, and this is a great way to keep that from happening. Extremely lightweight at only 1.3 Oz's it adds virtually no weight to the crank which is important for balance and vibration.

Kit Includes:

  • 1x Aluminum Crank Bolt Capture
  • 8x Fasteners Gr. 12.9

This part fits the following BMWs:
2006-2013 N54 

Show More Show Less

Elring Rear Crankshaft Seal
For vehicles with production date up to 01/2009
2X Entries Into Our F80 M3 Sweepstakes
Elring - Corporate Logo
T#:591493
Part#: 11117584398
In Stock
$ 23.99

This product was last offered at the strikethrough price on
10-26-2026

$ 23.15 USD
Free Shipping on orders $49 and up
$ 23.15 USD
Free Shipping on orders $49 and up
90x110x12mm - usually replaced when servicing the timing chains
Vargas N54/55 Billet Crank Seal Guard - BMW N54 N55 3.0L
2X Entries Into Our F80 M3 Sweepstakes
Vargas Turbo Technologies - Corporate Logo
T#:638889
Part#: VTT-CRANKGUARD
In Stock
Starting at $ 89.99 USD
Free Shipping
Starting at $ 89.99 USD
Free Shipping
It is a well-known issue on the BMW N54/55 platforms that your serpentine belt can fail for various reasons. When this happens, there is a high chance of the belt getting sucked behind the front damper pulley and then being pushed past the crank seal into your oil pan. From there it can get sucked into the oil pick up causing total engine failure. Even if you do not lose the engine, it is a COSTLY repair to remove the sub-frame and drop the oil pan to remove the belt. The best way to combat this is to watch for oil leaks and keep up on your maintenance. BUT, even with those preventative measures, pre-mature belt failure can occur. This crank seal guard installs over your front crank seal and will keep the belt from being sucked in if a belt failure does occur. This is a cheap way to ensure you do not end up having to replace your motor from oil starvation due to an ingested belt. Vargas' seal is different from those already on market in two major ways. Firstly, it is not offensively priced. Secondly, it is 100% billet with no welds on the tabs to break, no cheap bent thin steel pieces. 100% Billet 6061-T6 aluminum, anodized black for long-term corrosion resistance. Crank Seal Guard includes: One VTT Billet N54/55 Crank Seal Guard Two extended 12.9 Grade bolts, and two stainless washers We highly recommend you install WITH a crank bolt capture at the same time, as you have to remove the damper anyway. Then you will get the benefit of helping eliminate the dreaded spun crank hub and the crank seal issue
Show More Show Less

Bosch - Corporate Logo
T#:591891
Part#: 13537620946
In Stock
$ 98.99

This product was last offered at the strikethrough price on
07-06-2026

$ 57.99 USD
Free Shipping on orders $49 and up
$ 57.99 USD
Free Shipping on orders $49 and up
A vital component for high pressure fuel system function
Vargas Turbo Technologies - Corporate Logo
T#:558795
Part#: VTT-CRANKHUB-1
In Stock
$ 889.99 USD
Free Shipping
$ 889.99 USD
Free Shipping
Under certain conditions, the N55 crank hub likes to spin, without warning and even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines which press into the crank, and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and ECS are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution.
Show More Show Less

Bosch - Corporate Logo
T#:394329
Part#: SR0492N
In Stock
$ 249.17

This product was last offered at the strikethrough price on
08-14-2026

$ 237.99 USD
Free Shipping
$ 237.99 USD
Free Shipping

If your car won't turn over, there is a good chance your starter is shot. Bosch's OEM starter is a high quality replacement that will give you peace of mind thanks to its long life-span. OEM replacement for the original BMW part # 12411312104 and 12411312130. This is a NEW, not used, component with no included core charge!

Bosch is one of the largest OEM producers of Genuine BMW and aftermarket parts in the world, providing parts for almost every major automotive manufacturer. Bosch has likely supplied many of the original electrical (and mechanical) parts for your BMW. Thanks to their quality, high durability, and reliability, you should expect a long service life from Bosch products.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

We recommend replacing hardware when doing your starter, since the bolts are aluminum and threads become stretched: Genuine BMW aluminum starter hardware set 12410392577 

 

Used on a wide variety of models with the BMW N52, N54, and N55 engines, including: E9X, F01/02, F07/10, E8X, E70, E60/61, F25, F30, and Z4.

Show More Show Less

Bosch - Corporate Logo
T#:583739
Part#: 13518604232
In Stock
$ 286.99

This product was last offered at the strikethrough price on
07-19-2026

$ 217.99 USD
Free Shipping on orders $49 and up
$ 217.99 USD
Free Shipping on orders $49 and up

The most common reason fuel pumps fail is a plugged or restricted fuel filter, which makes the pump work harder. When a fuel pump starts to go bad, you may experience lack of power, no start, bucking, sputtering, or the engine may stop running. If this is occurring be sure to replace it before you are left without a working a vehicle.

Bosch is one of the largest OEM producers of Genuine BMW and aftermarket parts in the world, providing parts for almost every major automotive manufacturer. Bosch has likely supplied many of the original electrical (and mechanical) parts for your BMW. Thanks to their quality, high durability, and reliability, you should expect a long service life from Bosch products.

As a leading source of high-performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts. All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

Show More Show Less
Elring - Corporate Logo
T#:596428
Part#: 11137566644
In Stock
$ 33.43

This product was last offered at the strikethrough price on
09-28-2026

$ 23.79 USD
Free Shipping on orders $49 and up
$ 23.79 USD
Free Shipping on orders $49 and up
Bosch - Corporate Logo
T#:1722
Part#: 12120034087
In Stock
$ 95.94 USD
Free Shipping
$ 95.94 USD
Free Shipping
Set of six replacement spark plugs for your N54 powered BMW


OEM Bosch High-Pressure Fuel Pump & Fuel Filter - N55 3.0L
For vehicles with a production date from 03/2014 - Also fits models up to 03/2014 with ...
Bosch - Corporate Logo
T#:568683
Part#: 13518604231
In Stock
$ 311.99 USD
Free Shipping
$ 311.99 USD
Free Shipping
This is Bosch's updated high pressure fuel pump "HPFP" for BMW's with the N55 turbo engine. This fuel pump is the OEM equivalent to BMW part number 13518604231 and supersedes BMW part number 13517610761. Bosch is one of the largest OEM producers of Genuine BMW and aftermarket parts in the world, providing parts for almost every major automotive manufacturer. Bosch has likely supplied many of the original electrical (and mechanical) parts for your BMW. Thanks to their quality, high durability, and reliability, you should expect a long service life from Bosch products. As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts. All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!
Show More Show Less
Elring - Corporate Logo
T#:340679
Part#: 11117587168
In Stock
$ 34.99 USD
Free Shipping on orders $49 and up
$ 34.99 USD
Free Shipping on orders $49 and up

Rubber seals are often hardened and damaged by excessive heat and constant temperature changes causing them to become brittle and crack or split. If your seal has split, replace it with a new Elring seal for long reliability and to prevent further problems.

Elring is one of the biggest OEM names in the manufacturing of high quality gaskets that are available for very affordable prices. Elring has supplied many automotive names for years with the gaskets that seal your car's components from day 1 so you can rest assured that these components will last for a long time to come!

Fits the following BMW engines:
N20
N52
N54
N55
S55

Show More Show Less
Elring Crankshaft Seal - Front
For vehicles with a production date up to 02/2011
2X Entries Into Our F80 M3 Sweepstakes
Elring - Corporate Logo
T#:362853
Part#: 11117547842
In Stock
$ 22.99

This product was last offered at the strikethrough price on
10-26-2026

$ 22.29 USD
Free Shipping on orders $49 and up
$ 22.29 USD
Free Shipping on orders $49 and up
65x79x10 - Usually replaced when servicing the timing chains

Vargas Turbo Technologies - Corporate Logo
T#:18733532
Part#: VTT-CRANKHUB-6
In Stock
$ 986.99

This product was last offered at the strikethrough price on
06-28-2026

$ 939.99 USD
Free Shipping
$ 939.99 USD
Free Shipping
Under certain conditions, the N55 crank hub likes to spin, without warning and even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines which press into the crank, and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and ECS are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution.
Show More Show Less

Elring - Corporate Logo
T#:2691316
Part#: 11127614700
In Stock
$ 48.99

This product was last offered at the strikethrough price on
09-03-2026

$ 36.49 USD
Free Shipping on orders $49 and up
$ 36.49 USD
Free Shipping on orders $49 and up
Everywhere there is a seam on your engine, there is the potential for an oil leak. This is prevented through the use of gaskets and seals. One such gasket that prevents oil leaks is the valve cover gasket. This gasket is used to seal the gap between the valve cover and the cylinder head, however, since this gasket is made of rubber it has a tendency to become brittle, crack, and start to leak due to its constant exposure to heat and engine oil.
Show More Show Less
Elring - Corporate Logo
T#:2691317
Part#: 11127614701
In Stock
$ 47.99

This product was last offered at the strikethrough price on
08-11-2026

$ 34.91 USD
Free Shipping on orders $49 and up
$ 34.91 USD
Free Shipping on orders $49 and up
Everywhere there is a seam on your engine, there is the potential for an oil leak. This is prevented through the use of gaskets and seals. One such gasket that prevents oil leaks is the valve cover gasket. This gasket is used to seal the gap between the valve cover and the cylinder head, however, since this gasket is made of rubber it has a tendency to become brittle, crack, and start to leak due to its constant exposure to heat and engine oil.
Show More Show Less

Vargas Turbo Technologies - Corporate Logo
T#:51813315
Part#: VTT-TI-DRAIN
In Stock
$ 31.99 USD
Free Shipping
$ 31.99 USD
Free Shipping
The VTT Burnt Titanium Magnetic Oil Drain Plug is a critical upgrade for any performance enthusiast looking to maximize engine longevity.
Elring Timing Cover Output Shaft Seal
2X Entries Into Our F80 M3 Sweepstakes
Elring - Corporate Logo
T#:591588
Part#: 11147647380
In Stock
$ 23.99 USD
Free Shipping on orders $49 and up
Seals the timing case on the front of the engine.

Bosch - Corporate Logo
T#:590661
Part#: 12230035934
In Stock
$ 29.99 USD
Free Shipping on orders $49 and up
$ 29.99 USD
Free Shipping on orders $49 and up
Replace your worn out glow plug with this high-quality Bosch plug to eliminate hard starts during cold weather. This OEM part replaces BMW part # 12230035934. Before purchasing this plug, please confirm which plug is the proper replacement for your vehicle. Your BMW will have plugs from either Bosch or Beru. If your plugs are Bosch, please confirm your BMW has GLP5 plugs and not GLP6 plugs. Most vehicles with a production date up to 04/2019 came from the factory with GLP5 plugs. Bosch is one of the largest OEM producers of Genuine BMW and aftermarket parts in the world, providing parts for almost every major automotive manufacturer. Bosch has likely supplied many of the original electrical (and mechanical) parts for your BMW. Thanks to their quality, high durability, and reliability, you should expect a long service life from Bosch products. As a leading source of high-performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts. All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!
Show More Show Less

Vargas Ignition Coil Kit (Red) - N5x
2X Entries Into Our F80 M3 Sweepstakes
Vargas Turbo Technologies - Corporate Logo
T#:5309610
Part#: VTT-COIL-N5X-RED
In Stock
$ 169.99 USD
Free Shipping
$ 169.99 USD
Free Shipping
Vargas has contacted multiple coil manufacturing companies, paying for individual coils to be made then putting them through rigorous testing in the USA to ensure they matched or exceeded factory output. Once satisfied with the testing, the best performing coils were made to various colors and specs. Vargas is proud to offer a new line of ignition coil replacements for N5x Engines. VTT N5X coils are tested against Delphi 10571 coils which are an upgrade over stock N5X factory coils. The VTT performance matches or exceeds a Delphi 10571 Coil. The coils are offered in a choice of black, red, and blue.
Show More Show Less
Elring - Corporate Logo
T#:2602228
Part#: 11148483798
In Stock
$ 58.99 USD
Free Shipping on orders $49 and up
The rear main oil seal or crankshaft seals is one of the most difficult to replace. However, they often fail, and when they do, your car will be marking it's territory with little oil drops wherever you park. Apart from making a mess, it can also cause oil to come in contact with the clutch surface. Replace yours and keep your oil in your engine.
Show More Show Less
Bosch Flow Matched EV14 Injectors - US CAR Connector (EV6) - 750cc - ...
NOT A DIRECT REPLACEMENT FOR FACTORY INJECTORS - For use with aftermarket port injectio...
Bosch - Corporate Logo
T#:36947243
Part#: 501-0028
In Stock
$ 415.99 USD
Free Shipping on orders $49 and up
$ 415.99 USD
Free Shipping on orders $49 and up
The Black Market Parts Genuine Bosch Motorsports EV14 fuel injectors featuring USCAR (EV6) connector matched and packaged in a pack of 6 units. Direct plug-in for Motiv Reflex, AIC, and Nexsys Motorsports
Show More Show Less


Vargas Ignition Coil Kit (Blue) - N5x
2X Entries Into Our F80 M3 Sweepstakes
Vargas Turbo Technologies - Corporate Logo
T#:5309605
Part#: VTT-COIL-N5X-BLU
In Stock
$ 169.99 USD
Free Shipping
$ 169.99 USD
Free Shipping
Vargas has contacted multiple coil manufacturing companies, paying for individual coils to be made then putting them through rigorous testing in the USA to ensure they matched or exceeded factory output. Once satisfied with the testing, the best performing coils were made to various colors and specs. Vargas is proud to offer a new line of ignition coil replacements for N5x Engines. VTT N5X coils are tested against Delphi 10571 coils which are an upgrade over stock N5X factory coils. The VTT performance matches or exceeds a Delphi 10571 Coil. The coils are offered in a choice of black, red, and blue.
Show More Show Less
VTT BMW N54 “DI Injector” Delete Kit
2X Entries Into Our F80 M3 Sweepstakes
Vargas Turbo Technologies - Corporate Logo
T#:11497326
Part#: VTT-N54-DI-DELET
In Stock
$ 339.99 USD
Free Shipping
$ 339.99 USD
Free Shipping
Looking to get rid of the troublesome and expensive DI injectors on your BMW N54 and move to PI only and a standalone? If so VTT has you covered with its new N54 PI delete kit. This kit allows you to SAFELY remove the DI injectors, install our delete fittings, and run PI only. We machined these deletes from 310 Stainless for extreme heat, and corrosion resistance, and include 3 hold downs. These DI deletes COMPLETELY get rid of all factory provisions, including the seal. If the seal is left intact with no fuel to cool the injector or delete it will quickly overheat and melt the delicate seal causing combustion gasses to escape the engine creating misfires, and worse possibly damaging your injector bore on the cylinder head. Our deletes are machined to be a press fit into the cylinder, and can be either cooled with liquid nitrogen, and dropped in, or tapped in with a hammer, and then held down with the included hold downs. We also include M6 tapped holes on the top of each one in case they need to be removed you can attach a slide hammer, and remove the delete. These are sold as a kit and come with the following 6 – 310 Stainless DI Delete fittings 3 – Hold down brackets​ Completetion of this kit will require the purchase of HPFP delete plate - ES# 4623950 PLEASE NOTE: THIS KIT REQUIRES EXTENSIVE MODIFICATIONS TO CONVERT YOUR ENGINE TO PI ONLY. THIS INCLUDES BUT IS NOT LIMITED TO A FULL PORT INJECTION SOLUTION, AND STAND-ALONE TO RUN THE PI SYSTEM. WE RECOMMEND THIS PNP SYSTEM USING THE MAXX ECU IT PROVIDES ALL YOU NEED TO GET UP AND RUNNING WITH PI ONLY ON THE TUNING SIDE OF THINGS – https://www.pnpecu.com/pnpecu-maxxecu-n54-pnp-kit-437-p.asp
Show More Show Less
Elring Cylinder Head Gasket - N54 3.0L
1.215mm thickness - for use with an unmachined head
2X Entries Into Our F80 M3 Sweepstakes
Elring - Corporate Logo
T#:379331
Part#: 11127557265
Ships in 2 Business Days
$ 144.78

This product was last offered at the strikethrough price on
05-08-2026

$ 139.78 USD
Free Shipping
$ 139.78 USD
Free Shipping

The head gasket is exposed to high pressure and heat for extremely long periods of time. Over a long period of time, these may develop a slight oil leak and must be replaced ASAP to prevent damage to the engine. It should also be replaced any time that the engine head is removed to ensure the best seal possible.

Elring is one of the biggest OEM names in the manufacturing of high quality gaskets that are available for very affordable prices. Elring has supplied many automotive names for years with the gaskets that seal your car's components from day 1 so you can rest assured that these components will last for a long time to come!

Fits the following BMW engines:
N54 3.0L

Show More Show Less

VTT N54 Vacuum Pump Block Off Plate
2X Entries Into Our F80 M3 Sweepstakes
Vargas Turbo Technologies - Corporate Logo
T#:11497328
Part#: VTT-N54-VACUUM-B
In Stock
$ 127.99 USD
Free Shipping
$ 127.99 USD
Free Shipping
Looking to remove the HPFP or DI system on your N54? this plate will block the vacuum pump and prevent oil leaks. You will need to remove any fuel lines, etc. Kit includes Block Plate Note – Plates may come in a clear or anodize black finish depending on stock on hand
Show More Show Less

Elring - Corporate Logo
T#:2513314
Part#: 11127566288-9
In Stock
$ 111.99

This product was last offered at the strikethrough price on
06-16-2026

$ 83.47 USD
Free Shipping on orders $49 and up
$ 83.47 USD
Free Shipping on orders $49 and up
If there is a large amount of oil on the sides of the engine or if you can smell burning oil, chances are it's a bad valve cover gasket. The gasket fails and allows oil to seep down onto the side of the engine and other parts causing a mess and reducing the amount of oil in your engine. This replacement gasket from Elring is perfect to prevent any further oil leaks. Includes the following: Valve Cover Gaskets - Left & Right Valvetronic Seals Elring is one of the biggest OEM names in the manufacturing of high-quality gaskets that are available for very affordable prices. Elring has supplied many automotive names for years with the gaskets that seal your car's components from day 1 so you can rest assured that these components will last for a long time to come!
Show More Show Less
N54 Spline Lock Crank Hub Solution With Complete Package
2X Entries Into Our F80 M3 Sweepstakes
Vargas Turbo Technologies - Corporate Logo
T#:18733525
Part#: VTT-CRANKHUB-3
In Stock
$ 939.99 USD
Free Shipping
$ 939.99 USD
Free Shipping
Anyone with a modified N54 knows the risks involved. Upping the performance of any engine can come with some inherent risk; if we add more boost but not fuel, detonation will occur (or worse). Furthermore, improper installation, maintenance, or operation can turn a perfectly healthy engine into a paperweight. The worst failures, however, are the ones we don't plan for. When the engine simply can't handle the stresses its put under, or the design is such that it simply does not support extreme conditions. Enter the N54 crank hub. Under certain conditions, it likes to spin without warning, even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines that press into the crank and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Vargas spent many months testing, and retesting this design, utilizing well over 10 different samples to come to the final production version. During testing, the final hub managed to break the testing rig before slipping. These have been bench-tested, and real-world tested on the VTT N54 race car spinning 8K RPM, and making well over 900WHP. Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and Turner Motorsport are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution.
Show More Show Less

Elring - Top-end Gasket Set for Cylinder Head - N54 3.0L
2X Entries Into Our F80 M3 Sweepstakes
Elring - Corporate Logo
T#:383859
Part#: 11127572758
In Stock
$ 223.99

This product was last offered at the strikethrough price on
10-27-2026

$ 153.99 USD
Free Shipping
$ 153.99 USD
Free Shipping

If there is a large amount of oil on the sides of the engine or if you can smell burning oil, chances are it's a bad valve cover gasket. The gasket fails and allows oil to seep down onto the side of the engine and other parts causing a mess and reducing the amount of oil in your engine. This replacement gasket from Elring is perfect to prevent any further oil leaks.

Includes most of the seals you will need other than the head gasket.

Elring is one of the biggest OEM names in the manufacturing of high quality gaskets that are available for very affordable prices. Elring has supplied many automotive names for years with the gaskets that seal your car's components from day 1 so you can rest assured that these components will last for a long time to come!

Fits the following engines:
N54 3.0L

Show More Show Less
OEM Bosch Spark Plugs - Pack Of 8 - BMW E70/71 F01/02 F07/10/12/13 N6...
For vehicles with the early N63 engine - Not for the later N63TU (N63N) Engine
Bosch - Corporate Logo
T#:379356
Part#: 12120037580KT2KT
In Stock
$ 79.99 USD
Free Shipping
$ 79.99 USD
Free Shipping
Poor idle, low fuel efficiency, and engine misfire codes are all symptoms of worn spark plugs. Replace yours with OE Bosch parts to get your engine running as well as possible.

Elring Valve Seal Repair Kit
2X Entries Into Our F80 M3 Sweepstakes
Elring - Corporate Logo
T#:591665
Part#: 11340054492
Ships in 1-2 days
$ 53.99

This product was last offered at the strikethrough price on
08-14-2026

$ 45.99 USD
Free Shipping on orders $49 and up
$ 45.99 USD
Free Shipping on orders $49 and up

Billet Check Valve - 10 Barb
2X Entries Into Our F80 M3 Sweepstakes
Vargas Turbo Technologies - Corporate Logo
T#:597641
Part#: VTT-CHECK-2
Ships in 3 Business Days
$ 36.99 USD
Free Shipping
$ 36.99 USD
Free Shipping
Vargas Turbo has you covered when you are installing a custom turbo setup. With all of the adapters you need and all the valves necessary, the only real limiting factor is your imagination!
Vargas Turbo Technologies - Corporate Logo
T#:18733531
Part#: VTT-CRANKHUB-5
Ships on Nov 17, 2026
$ 880.99 USD
Free Shipping
$ 880.99 USD
Free Shipping
Under certain conditions, the N55 crank hub likes to spin, without warning and even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines which press into the crank, and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and ECS are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution.
Show More Show Less
Vargas Turbo Technologies - Corporate Logo
T#:5122266
Part#: VTTFILTERCAPCLR
In Stock
$ 89.99 USD
Free Shipping
$ 89.99 USD
Free Shipping
VTT is proud to offer a billet replacement for the factory plastic Oil filter housing cap. This cap does away with the weak plastic cap and the need for a special tool for removal, while adding some pop and color to your engine bay. These oil filter housing caps retain ALL of the factory provisions for the filter basket, including the lower pins which are important for the proper function of pressure bypass, etc. They also have cooling fins to help with oil temps. Vargas Turbo designed these caps to complement their N5X Billet Oil caps and N5X Billet Power Steering caps so that all 3 will have the same design. The caps are offered in 4 colors – Red, Black, Blue, and Clear anodized
Show More Show Less


Bosch - Corporate Logo
T#:568424
Part#: 13517595339
In Stock
$ 332.99 USD
Free Shipping
$ 332.99 USD
Free Shipping
*Brand new HPFP - No Core Charge!* The High Pressure Fuel Pump (HPFP) is a point of weakness in many BMW engines and fuel systems. If this goes it will prevent your car from running or starting due to fuel starvation. Restore your fuel system's operation with high quality OE BMW fuel pump. As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts. All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform! When doing any sort of repair or maintenance there is no replacement for genuine factory parts. Turner Motorsport carries the Genuine BMW brand with pride and has the parts you need to complete your next project with confidence. Bosch High-Pressure Pump This item fits the following BMW Chassis: E70 X5M,E71 X6M,E70 X5,E71 X6,F01,F02,F10,F12,F13 Fits BMW Engines including: N63,N63N,S63
Show More Show Less
BMW N54 3.0L Billet Vaccum Relief Valve
2X Entries Into Our F80 M3 Sweepstakes
Vargas Turbo Technologies - Corporate Logo
T#:597525
Part#: VTT-VAC-RELIEF
In Stock
$ 104.99 USD
Free Shipping
$ 104.99 USD
Free Shipping

BMW N54 3.0L Billet Vacuum Relief Valve from Vargas Turbo Technologies offers precise control over crankcase vacuum levels. This high-quality billet valve allows users to adjust the vacuum pressure with ease, eliminating guesswork and ensuring optimal engine performance. By simply adding or removing shims, users can tailor the vacuum level to their needs.

  • Customizable Vacuum Levels: Adjust the vacuum pressure using supplied shims to achieve desired performance.
  • Direct Fit: Designed with -10ORB threads for easy installation into VTT modular PCV solutions and VTT Modular CNC valve covers.
  • Versatile Settings: Includes 5 vacuum settings ranging from 10' to 18' of vacuum based on shim configuration.
  • Enhanced Engine Protection: Helps prevent excessive vacuum that could affect engine seals or cause whistling.
Show More Show Less