BMW Tools & Specialty Equipment for BMW 6 Series F06 (2013+)

This tool comes in handy especially when working with an engine harness. Certain areas are always prone to corrosion and this tool makes having to re-pin a connector a breeze.

Unlike small screwdrivers, picks, and paper clips, these tools are the correct size and shape to remove and install tiny electrical pins and terminals at plastic block connectors with ease, and will not damage the connectors in the process.

Packaged in a blow molded case to keep everything secure and organized.

PRESSURE BRAKE BLEEDER:

We know bleeding brake alone is not only no fun, but much more complicated than it needs to be. Having a pressure bleeder give you the ability to keep the pressure on the brake system while you go under and crack open the bleeder screws to relieve the air pockets.

Features:

• Holds a full 3-Liters (3.17 qts) of brake fluid
• Easy to read 0-30 lbs pressure gauge built into the tank top
• Pressure relief valve for safe release of pressure
• 40" hose with detachable swivel fitting

FLUID CATCH BOTTLE:

keep your fluid's off the floor and into our catch bottle.  The bottle has fluid level markings from 0.2L to 0.7 liter. This feature allows you to measure how much fluid you have sent thru the system.  Our bleeder bottle features an expandable/collapsible top portion for easier storage. Gasket in cap prevents leakage. Tubing is extra long at 24" from cap to nipple. Flexible hose can be pushed down into bottle for storage when done. Bottle now features a handy hanger bracket to hang bottle from bottom of car.

Note:

• Do not exceed 20 PSI
• LIFETIME REPLACEMENT

WARNING: This product contains chemicals known to the state of California to cause cancer, birth defects, and/or reproductive harm. See above warning label as well as http://www.p65warnings.ca.gov for further information on Proposition 65 warnings.

Here's what makes this floor jack the best on the market:

• Dual pump pistons to reach maximum height in 5 pumps
• Low profile design keeping lowered cars in mind
• Easy maneuverability 
• Two piece quick release padded handle for storage or transport.

Details:

• Jack Capacity 2 Ton
• Max Lift Height 20"
• Low Height 3.25"
• Chassis Length 26.5"
• Overall Width 13"
• Saddle Diameter 4.5"
• Handle Length 50"
• Shipping Weight 50 lbs

When doing work where the mounts and support need to be removed from the engine or transmission having a engine support bar is wise. By using this engine support the stress is coming off of whatever components are still attached reducing future unnecessary repairs. The safety side of it is having the heavy engine and transmission firmly supported as it should be instead of questionable jack techniques.  

Features:

•  2" longer than most
• Deluxe transverse support for even more stability
•  Two angle chain hooks for safer and more stable chain support 
•  61" long and fully adjustable to any width
•  Weight rating is a full 1000 lbs.
•  Includes four rubber padded feet to prevent slipping and damage to cars finish 
• This tool features a dual hook design for holding engine or transmission in place
•  Powder coated for long life and durability

Note: It is important that chains are hooked to both sides of hook, like in photo to insure load is supported evenly. 

This professional-grade deluxe fender roller allows you to gently and gradually flatten your inner fender lips in order to increase your fender to tire clearance.

This new deluxe fender roller has been designed to fit most applications.

This is the perfect tool for:

If you want to lower your vehicle
If you want wider-than-stock wheels
If you are going to use wheel spacers or decreased offset
Will work with bolt patterns of 4x100 and 5x100 up to 4x114.3 and 5x130 with 12mm or 14mm lug bolts.

By rolling the fender lip flat, you can lower your car further, and give your car a wider stance, without your tires rubbing on the inside of the fender.

Fully adjustable for use on vehicles of different ride heights, offsets, and wheel bolt patterns.

Use of a heat gun is recommended to soften the fender surface during the rolling process and prevent paint cracking.

 This comprehensive kit is basically a one-stop-shop to pick up all the special torx, triple square, & hex bits you need to keep your car where it should be... on the road!

This Universal European Tool Kit features the following:

• Torx Screwdriver Kit - 6 Pieces (Sizes included: T10, T15, T20, T25, T27, & T30. Perfect for removing door and dashboard panels, interior trim, and smaller underhood components. )
• Swivel Head Triple Square Driver Kit - 4 Pieces (Set of four 3/8 drivers in M6, M8, M10, and M12 sizes. Perfect for working around corners in those hard to reach spots.)
• Specialty Bit Kit - 100 Pieces (100 piece torx & hex bit kit to fit a wide assortment of automotive fasteners. Made of hardened Chrome Vanadium steel, packaged in a handy blow molded case.)
• Go-Through Screwdriver Kit - 6 Pieces (Kit includes durable slotted & phillips head nickel-chromoly screwdrivers with hardened shafts that extend the entire length of the driver.)

3/8" DRIVE LONG FLEX HEAD RATCHET:

A professional quality flex ratchet features a fine satin finish designed for durability and easy clean up.

Features:

• Special designed 72T gear mechanism
• 5 degree of handle movement between gears 
• Flex head has 7 detent positions in a 180 degree swing
• Push button release holds socket tight until you are ready to release
• Ratchet is a full 290mm ( 11") long for extra leverage.

3/8" DRIVE 6 POINT SOCKET SET:

A satin chrome finish with a knurled ring around socket body, the knurling allows for a better grip when hands and sockets are covered in oil or grease. All sockets feature a radius in the corners for superior torque to the sides of the fastener, not the corner. Complete size coverage.

Includes:

• 8mm
• 9mm
• 10mm
• 11mm
• 12mm
• 13mm
• 14mm
• 15mm
• 16mm
• 17mm
• 18mm
• 19mm

LIFETIME REPLACEMENT on all items in this kit!

3/8-INCH DRIVE LONG FLEX HEAD RATCHET:

This professional quality flex ratchet features a fine satin finish designed for durability and easy clean up. Special designed 72T gear mechanism uses only 5 degree of handle movement between gears. This is  especially useful in tight areas. Flex head has 7 detent positions in a 180 degree swing. Push button release holds socket tight until you are ready to release.  No more dropped sockets. Ratchet is a full 290mm ( 11") long for extra leverage.

Part of our LIFETIME REPLACEMENT PROGRAM

1/2-INCH DRIVE LONG FLEX HEAD RATCHET:

This 1/2" drive flex head ratchet features a fine satin finish designed for durability and easy clean up. Special designed 72T gear mechanism uses only 5 degree of handle movement between gears. This is  especially useful in tight areas. Flex head has 9 detent positions in a 180 degree swing. Push button release holds socket tight until you are ready to release.  No more dropped sockets. 

Part of our LIFETIME REPLACEMENT program

Harmonic Balancer Puller and Installer Set

The Harmonic Balancer Puller and Installer Set is an essential tool kit designed for the effective removal and installation of harmonic balancers. This master set includes all the necessary bolts and adapters required for a wide range of applications, making it a versatile addition to any workshop or toolbox.

Benefits:

• Comprehensive Set: Includes all required bolts and adapters for most applications, ensuring compatibility with various vehicle models.
• Bilingual Instructions: Comes with bilingual instructions for easy use and understanding, catering to a broader range of users.
• Replacement Part Availability: Replacement parts are readily available, ensuring the tool kit remains functional and useful over time.
• Efficient Performance: Streamlines the process of removing and installing harmonic balancers, saving time and effort.
• Durable Construction: Built from high-quality materials for long-lasting durability and reliable performance.