BMW Engine Parts for BMW 6 Series F06 (2013+)

Ignition coils are key to the efficiency and performance of your BMW. With a faulty coil the spark plug is not burning the air/fuel mixture properly and that can lead to problems anywhere in the engine and exhaust (including catalytic converters and O2 sensors). Problems with one or more coils will cause a fault code but not always a check engine light. A misfire code may be related to an ignition coil but could be from other things as well. Sometimes a visual inspection of a coil and coil boot will give an indication of a failure. You can also move coils around to different cylinder banks to see if the misfire code follows a suspect coil. We suggest always having one or two coils on hand to keep as spares.

This is the current replacement for some BMW 6 and 8-cylinder engines built in the late 2000s and after. BMW has made numerous changes to ignition coil part numbers in recent years but has approved this part number to work in the vehicles listed below. It's listed as a replacement coil for N20, N55, and S55 engines. In March 2015 BMW approved it for N51/N52 engines. This part number replaces the previous BMW part number 12137594937 for the cars listed below.

Sold per coil. Includes boot and connector.

Common point of failure is the N52/N54 Oil Filter Housing Gasket. When leaks occur here, oil can get on your belts, among other important components, causing engine failure. Replace yours today to avoid future troubles!

Genuine Bmw Gasket - 11428637821

Featuring a T60 Torx head, the belt tensioner found on the N54/N55 engine has exceptionally tight quarters. Use of this tool will allow access to the lock pin hole without excessive component removal, making belt removal and installation a much easier task.

This tool fits all N54/N55 powered BMW, including: 
2008+ E82 BMW 135i 1M Coupe 
2014+ F22 BMW M235i 
2006+ E90 BMW 335i 335xi 335i xDrive - Sedan 
2007+ E92 BMW 335i 335is 335xi 335i xDrive - Coupe 
2007+ E93 BMW 335i - Convertible 
2012+ F30 BMW 335i 335i xDrive - Sedan 
2013+ F32 BMW 435i 435i xDrive - Coupe 
2014+ F34 BMW 335i xDrive GT - Gran Tourismo 
2015+ F80 BMW M3 - Sedan 
2015+ F82 BMW M4 - Coupe 
2015+ F83 BMW M4 - Convertible 
2006-2010 E60 BMW 535i 535xi 535i xDrive 
2010+ F07 BMW 535i GT, 535i xDrive GT 
2011+ F10 BMW 535i 535i xDrive 
2012+ F13 BMW 640i 
2009+ F01 BMW 740i 740li 
2011+ F25 BMW X3 xDrive35i 
2007-2013 E70 BMW X5 xDrive35i 
2007-2014 E71 BMW X6 xDrive35i 
2009+ Z4 BMW Z4 sDrive35i Z4 sDrive35is 

At almost half of the normal cost of Genuine BMW Installation Tool - No. 130190, this Schwaben BMW Fuel Injector O-Ring Tool Set is a perfect alternative to save money and ensure your have the proper tool for the job when it come time to service your fuel system. Make sure the job is done correctly the first time with this specialty item, relieving frustration and saving time all while preventing you from damaging critical seals or the injector itself that could otherwise be damaged if using the wrong tools for the job. 

This tool set includes all of the same components you would get with the BMW tool, the seal cutting pliers and seal installation components, made to exact specifications for perfect operation.

The Schwaben Piston Ring Filer is a vital tool for obtaining the precise end gap necessary for optimal piston ring performance.

This filer allows you to swiftly and accurately file piston rings to exact measurements, enhancing your engine’s efficiency and lifespan. By simply positioning the piston ring and turning the handle, you can easily rotate the abrasive wheel for a smooth and effective filing process.

**Note:** For the Schwaben Universal Piston Ring Compressor, check out T25805755!

Key Features:

• Optimize Performance: Achieve the perfect end gap crucial for top engine efficiency.
• Quick and Precise: File rings to exact specifications with ease.
• Easy Operation: Position the piston ring and turn the handle to effortlessly rotate the abrasive wheel.
• Enhanced Engine Longevity: Accurate end gaps contribute to longer engine life and better performance.

Instructions:

1. Position the Ring: Place the piston ring on the outer edge against the stop and align the ends squarely against the grinding wheel. Apply light, even pressure against the wheel to prevent grinding too large a gap.
2. Operate the Tool: Turn the handle so the grinding wheel turns towards the inside edge of the ring (counter-clockwise when viewed from the handle side of the tool).
3. Exercise Caution: This is a diamond grinding wheel. It cuts fast!

Checking Piston Ring Gap:

1. Deburr the Ring Ends: Carefully remove any burrs on the ring ends before placing the ring in the bore. A light touch with a fine abrasive stone works well.
2. Clean the Rings: Thoroughly clean the rings with lacquer thinner or acetone, as the paint coating from the factory may occasionally scratch the cylinder bore. Always wear gloves during this process.
3. Position the Ring in the Cylinder: Place the ring squarely in the cylinder bore, about 1" down from the deck surface. An upside-down flat-top piston will help you properly square the ring.
4. Measure the End Gap: Use a feeler gauge to measure the ring's end gap. Apply light grinding pressure and check frequently to avoid making the end gap too large.

WARNING: This product contains chemicals known to the state of California to cause cancer, birth defects, and/or reproductive harm. See above warning label as well as http://www.p65warnings.ca.gov for further information on Proposition 65 warnings.