BMW Drivetrain Parts for BMW 2 Series F22 (2014+)

The ZF 8-speed automatic transmission (8HP) has become the go-to choice for performance enthusiasts, delivering lightning-fast shifts, impressive torque handling, and ample tuning potential. However, the stock transmission pan falls short in critical areas. Its plastic construction, integrated non-replaceable filter, and limited fluid volume leave little margin for error in demanding conditions.

To address these limitations, we've engineered a premium solution: a cast aluminum transmission pan that boosts durability, cooling performance, and serviceability. Designed with enthusiasts in mind, this upgraded pan increases fluid capacity by 1 liter to reduce transmission temperatures and improve long-term reliability, even under aggressive driving or track conditions.

Built to outlast and outperform the OEM plastic pan, the aluminum construction resists damage from road debris and eliminates the risk of cracking. Our pan is hard-coat anodized in black for superior corrosion protection and a long-lasting finish that looks as good as it performs.

Our aluminum pan upgrade is engineered to work seamlessly with the OEM G8X 8HP transmission filter (24007855263), allowing for easy and cost-effective fluid service. Integrated magnets help to trap metal particulate, extending the life of your transmission by keeping contaminants out of the fluid.

Key Features:

Cast aluminum construction offers superior strength and resilience over the OE plastic pan

Increased fluid capacity (+1L) enhances thermal management and reduces the risk of overheating

Serviceable design uses the OEM G8X transmission filter for easy, affordable maintenance

Hard coat anodized finish provides exceptional corrosion resistance and longevity

Integrated magnets collect metallic debris, protecting transmission internals

Installation:

Vehicle plastic belly pans may vary. Because the Turner 8HP transmission pan is taller to allow for increased fluid capacity, some vehicles may require trimming of the plastic belly pan, or the belly pan may need to be installed over the transmission pan where it may make contact.

At Turner we are very familiar with the N55 and B58. These are the new generation engines that you you can pull quite a bit of power from quite easily, if you want to put the power to the pavement the factory bushings and reinforcement just wont cut it. With soo many performance parts available for the turbocharged engines, it is very easy to make power but keeping the car under control can be another story. Reduce wheel hop, extend the life of your bearings, and add stability to your chassis!

Our in-house engineers created a solution to help transfer the power to the ground, the result is a simple yet astounding improvement to the performance of your vehicle. The rear diff brace helps put power down by reducing wheel hop and preventing losses during power transfer. With the added rigidity the rear end feels tighter for high speed applications and will extend the life of your choice of OE or aftermarket bushings.

Soft factory rubber differential bushings absorb vibrations between the chassis and differential, providing comfort and softness for normal driving conditions. As these bushings wear you will experience lackluster performance/response and they will need to be replaced. You can extend the life of these bushings while providing increased chassis stability with our differential brace for your F chassis. Add new poly differential bushings for an even better experience (T#:656153)

Note: Drilling is required for installation

Benefits:

Reduce unwanted drivetrain deflection, offering a more enhanced driving experience
Reduced wheel hop
Extend the life of your bushings
Reduced wear on the differential bearing
Increased transfer of power to the pavement
Increased high speed stability
Engineered by Turner to withstand extreme driveline forces of over 1000 Ft/lbs of torque
Provides necessary installation tooling to properly secure brace
PART DESIGN:

Designed and engineered in-house using state of the art 3D laser scanning and CAD technology for precision fitment
Constructed using aircraft grade 6061-T6 Aluminum, finished in Turner Blue anodization
FEA simulations run to maximize stiffness to weight at base engine power and torque levels with plenty of room for growth
Corrosion resistant Yellow Zinc-Chromate coated grade 10.9 Fasteners
KIT CONTENTS

Turner Blue Anodized Rear Diff Brace
Drill guides for precision installation
Hardware for installation
INSTALLATION:

- Click HERE for Installation Instructions -
Requires 10mm + 15mm carbide tip steel drill bits (T#16907167)
PRODUCT DEVELOPMENT

Turner F Chassis Differential brace was designed, engineered, tested and quality inspected by our Research and Development team at Turner. Nothing but the highest level of precision and quality through leading-edge product development technology including FARO laser scanning for reverse engineering and quality inspection, SolidWorks 3D CAD modeling, rapid prototyping utilizing our in-house 3D printer and rigorous long term product testing.

Increase drivetrain rigidity and put that power to the ground! This industry-leading encapsulated design reduces NVH and prevents heat transfer.

From the factory, all BMW models are equipped with soft rubber or fluid-filled engine mounts. While these mounts perform well at isolating drivetrain vibrations, they are prone to degradation and allow for significant drivetrain movement. This often results in a loose-feeling driveline, missed shifts, and a generally disconnected driving feel.

To address these issues, We have developed a performance alternative. Constructed from 6061 Billet Aluminum, these mounts are built to last. While most performance drivetrain mounts feature solid or polyurethane-bonded aluminum construction, the engineers at Turner designed a unique four-piece design that disburses NVH (noise, vibration, and harshness). This multi-piece design offers the added benefit of serviceability. Additionally, encapsulating the polyurethane and adding a TecaPeek isolator prevents heat transfer to the insert, increasing the lifespan and durability of the mount.

Features & Benefits:

High-strength 6061 billet aluminum construction
80A Polyurethane provides a considerable increase over stock rubber durometer, eliminating excess deflection and ensuring drivetrain stiffness.
Instead of the typical polyurethane-bonded aluminum construction, this mount is encapsulated to reduce NVH (noise, vibration, and harshness).
Finished in black hard-coat anodized for a clean, durable, and corrosion-resistant finish.
TecaPeek isolator reduces heat transfer from the engine to the mount insert, increasing the lifespan of the mount.
A simple bolt-on design makes for an easy install
Replace your worn-out factory engine mounts and experience increased drivetrain rigidity, reduced deflection, and more precise shifting. Our Turner Performance Polyurethane Engine Mount Set is designed for maximum durability and strength while maintaining the perfect balance between stiffness and comfort—the perfect choice for your high-horsepower BMW!

Upgrade the shifting precision and feel of your BMW with Turner Motorsport Powerflex Shifter Carrier Street Bushings - Oval. Made of 90A urethane, these bushings replace the stock rubber ones to prevent sloppy shifting. The stiff urethane reduces play without adding vibration. Easy to install when the carrier is out of the car, these bushings ensure improved performance. Here are the key benefits:

• Enhances shifting precision and feel
• Prevents sloppy shifting caused by failed rubber bushings
• Made of 90A urethane for durability and stiffness
• Easy installation when carrier is removed

Eliminate the factory clutch delay valve and enjoy faster, more precise clutch engagement with the ECS Clutch Delay Valve (CDV) Removal Tool Kit. Designed for F and G-Chassis manual BMWs, this kit makes removing the hydraulic restrictor safe, simple, and reliable, no slave cylinder removal required.

Most modern BMWs come from the factory with a plastic slave cylinder featuring a CDV, intended to smooth engagement and reduce driveline shock for less experienced drivers. In practice, this restrictor can dull pedal feedback, slow shifts, and increase clutch wear. Removing it restores the sharp, direct clutch feel that BMW enthusiasts expect.

Key Benefits:

Faster, more predictable clutch engagement
Sharper pedal response and connected driving feel
No need to remove the slave cylinder
Tool Design:

Machined from durable 304 stainless steel
Includes precision removal and insertion tools
Knurled grip for easy handling
Built-in depth and angle control protects internal surfaces and ensures proper grommet alignment
Removal and Installation:

Disconnect the Clutch Line
Remove the clutch line from the slave cylinder to access the factory clutch delay valve.
Remove the Restrictor Plate
Thread the removal tool into the center of the small grommet. Once engaged, carefully pull the tool to remove the grommet and restrictor plate. The small rubber sealing O-ring will come out along with the plate.
Reinstall the O-Ring
Place the rubber O-ring onto the installation tool. Insert the tool into the slave cylinder to properly seat the O-ring in its original position.
Reconnect and Bleed the Clutch
Reattach the clutch line, add fluid, and bleed the system according to your manufacturer’s instructions.
Enjoy Enhanced Clutch Feel
With the delay valve removed, your clutch now engages faster and more predictably, giving your manual transmission the sharp, connected feel it was designed for.

BMW E36 E46 Powerflex Clutch Fork Pivot Pin - Street offers enhanced performance and reliability for BMW enthusiasts. Engineered by Powerflex, this clutch fork pivot pin is designed to improve the feel and response of the clutch system, providing a more direct and consistent engagement.

• Improved Performance: Upgrades the factory clutch fork pivot pin to deliver a more precise and responsive clutch operation.
• Enhanced Reliability: Built to withstand the demands of both daily driving and spirited driving, offering greater durability over OEM components.
• Quality Construction: Made from high-quality materials to ensure long-lasting performance and resistance to wear and tear.
• Direct Fit: Designed specifically for BMW E36 and E46 models, ensuring a perfect fit with no modifications required.
• Enhanced Driving Experience: Reduces clutch play and enhances engagement feel, contributing to a more engaging driving experience.

Installation Note: Designed for street use and compatible with standard clutch systems.

A sloppy shifter is one of the common complaints of older BMWs. In addition to the shifter linkage the transmission mounts contribute to rough and clunky shifting. BMW transmission mounts are rubber and get softer over time. This allows the transmission to dance around which changes the geometry of the shift linkage and could make it harder to shift. These urethane transmission bushings are stiffer than the stock rubber mounts and won't let the transmission shift around as much. The round design also has more surface area than the stock mounts which helps spread the load. Because the urethane is stiffer, expect more vibration to make its way into the shift lever area. Engine motor mounts should also be considered as a cause for driveline vibration, transmission movement, and poor shifting. Consider replacing your motor mounts at the same time as your tranny mounts.

Price is for the pair of transmission mounts with hardware.

This item fits the following BMWs: 
1989-1995  E34 BMW  525i 530i 535i 540i M5 
1992-1998  E36 BMW  318i 318is 318ti 318ic 323is 323ic 325i 325is 325ic 328i 328is 328ic M3 
1997-2003  E39 BMW  525i 528i 530i 540i M5 
1999-2005  E46 BMW  323i 323ci 325i 325ci 328i 328ci 330i 330ci M3 
2008-2012  E82 BMW  128i 135i 1M Coupe 
2006-2011  E90 BMW  325i 328i 330i 335d 335i - Sedan 
2006-2012  E91 BMW  328i - Wagon 
2007-2013  E92 BMW  328i 335i 335is - Coupe 
2007-2013  E93 BMW  328i 335i - Convertible 
1997-2002  Z3 BMW  Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i M Roadster M Coupe