BMW Engine Parts for BMW F87 M2 N55 3.0L

Valvetronic Actuator Replacement Kit - BMW N55 S55 3.0L

10X Entries Into Our F80 M3 Sweepstakes

T#:599759

Part#: 11377603979KT2

In Stock

Sale - Save 10% $ 268.99

This product was last offered at the strikethrough price on
05-03-2026

$ 241.95 USD

Add to Wish List

Qty

Sale - Save 10%

$ 268.99

This product was last offered at the strikethrough price on
05-03-2026

$ 241.95 USD

Add to Wish List

Includes actuator, actuator gasket and valve cover gaskets

N-Series Ultimate Performance Ignition Coil - Red - Set Of Six ...

10X Entries Into Our F80 M3 Sweepstakes

T#:23714967

Part#: NSERIESIGNCOILKT

In Stock

$ 205.99 USD

Add to Wish List

Qty

$ 205.99 USD

Add to Wish List

Upgrade your BMW's engine performance with the Dinan Performance Ignition Coil Service Kit. These high-quality ignition coils are crafted to enhance ignition power, ensuring optimal engine performance and efficiency. Engineered for durability and reliability, these coils provide improved throttle response, smoother idle, and enhanced fuel efficiency. Benefit from the Dinan Performance Ignition Coil Service Kit, designed to unleash the true potential of your BMW's engine.

Show More Show Less

VTT S55 Crank Bolt Capture - F8X S55 F3x N55

2X Entries Into Our F80 M3 Sweepstakes

T#:557934

Part#: VTT-S55-CBC

In Stock

$ 129.99 USD

Add to Wish List

Qty

$ 129.99 USD

Add to Wish List

The S55 suffers from a weak point in its crankshaft. It has been reported that when increasing the power to the engine, the crank hub can move or spin slightly under an extreme load.

MAC Single Turbo Boost Solenoid - N54 N55

T#:587715

Part#: MACSTS

In Stock

$ 51.99 USD

Add to Wish List

Qty

$ 51.99 USD

Add to Wish List

Use this plug and play low frequency MAC solenoid if retrofitting a single turbo kit to your N54 or N55. Includes plug and play harness connector for no splicing!

Billet Oil Filter Cap

T#:21045489

Part#: BMS-OFC

In Stock

Starting at $ 89.00 USD

Add to Wish List

Starting at $ 89.00 USD

Add to Wish List

The Burger Motorsports V2 billet aluminum oil filter cover is a metal upgrade that directly replaces your weak OE plastic cap for greater protection, better cooling, ease of removal/install, and looks great under the hood. The built-in 21mm hex and a 3/8" drive socket wrench fitting that does not require a special removal/install tool like the factory cap. Uses the OE oil filter, filter housing o-ring, and filter cage. Anodized for protection. This quality part is a must for any serious BMW owner. Replaces OEM part number 11427525334 - BMW Oil filter cover. Features and Benefits Solid aluminum design is much stronger than brittle plastic 21mm hex head + 3/8" drive socket wrench fitting Integrated heat sinks for better oil cooling Special tools are not required for removal/install like the factory cap Strong design won't fail under pressure Reuses OE filter cage and o-ring Anodized for protection Looks great under the hood Made in the USA

Show More Show Less

N54/N55 Low Temp Oil Thermostat Kit - 70c

10X Entries Into Our F80 M3 Sweepstakes

T#:52621839

Part#: 008731KT1

In Stock

Sale - Save 23% $ 74.98

This product was last offered at the strikethrough price on
05-03-2026

$ 57.74 USD

Add to Wish List

Qty

Sale - Save 23%

$ 74.98

This product was last offered at the strikethrough price on
05-03-2026

$ 57.74 USD

Add to Wish List

Upgrade your stock oil cooler thermostat for improved performance. Swap your factory 110-degree Celsius thermostat for a new 70-degree Celsius version for faster oil flow and extended temperature control. With oil temperatures reaching 230 degrees Fahrenheit by the time your factory thermostat opens, initiating oil flow at lower temperatures proves more effective than attempting to cool down already elevated temperatures.

Utilizing a factory-style thermostat, this upgrade can be used in all weather conditions and allows your engine to warm up properly, unlike thermostat bypass kits.

Kit contents:

Lower temperature thermostat - 70c (158F) vs Factory 110c (230F)
Low temp thermostat spring

Show More Show Less

BMW Oil Cap Crankcase Breather - All BMW w/2 prong oil fill cap ...

2X Entries Into Our F80 M3 Sweepstakes

T#:558084

Part#: VTT-CRANK-BREATH

In Stock

$ 129.99 USD

Add to Wish List

Qty

$ 129.99 USD

Add to Wish List

VTT is happy to introduce the first and only available plug and play crankcase breather kits for ALL BMW applications that use the two-prong oil tab style oil fill caps. With this breather simply remove your oil cap, install the breather, and instantly free up horsepower, improve turbo draining, remove crankcase pressure, all while adding a cool look to your engine bay.

Can be used by itself with the stock PCV system to eliminate crankcase pressure, or with any number of PCV setups for the ultimate in crankcase pressure relieve

Made from 6061-T6 Aircraft aluminum anodized black for a long-lasting finish, 4 stainless steel baffles for complete oil control, a PTFE one way check ball, a high-quality filter, and clamp all work together to keep crankcase pressure where it belongs, out of your crankcase.

This breather will fit:
ALL BMW's with the two-prong style oil fill cap including but not limited to N54, N55, S55, S54

NOTE: NOT ALL THE MODELS LISTED HAVE THE SAME HOOD CLEARANCE, WE CANNOT SAY WHICH MODELS WILL HAVE CLEARANCE ISSUES, AND WHICH WILL NOT AS WE HAVE NOT TEST IT ON ALL MODELS. IF YOU ARE ORDERING THE BREATHER FOR ANYTHING OTHER THAN AN N54 TEST CLOSE YOUR HOOD CAREFULLY TO ENSURE CLEARANCE IF IT DOES NOT FIT LET US KNOW, AND WE WILL GET YOU A REFUND ONCE THE BREATHER IS RETURNED.

MODEL LIST OF REPORTED CLEARANCE ISSUES: N55 E/F 3 SERIES

Show More Show Less

Aluminum Valve Cover kit - F22/23 F3X F87 N55 3.0L

10X Entries Into Our F80 M3 Sweepstakes

T#:23913951

Part#: F3XN55MVCKT

In Stock

Sale - Save 19% $ 406.99

This product was last offered at the strikethrough price on
05-03-2026

$ 328.81 USD

Add to Wish List

Qty

Sale - Save 19%

$ 406.99

This product was last offered at the strikethrough price on
05-03-2026

$ 328.81 USD

Add to Wish List

If your valve cover has become cracked or warped, replace it with this quality Aluminum Valve Cover from Bremmen Parts to prevent leaks and further valvetrain damage. The upgraded aluminum valve cover included in this kit is the perfect solution to replace standard plastic valve covers that crack and split over time, leading to oil leaks! This kit includes everything needed to install a new valve cover, including a new CCV hose, gaskets, and hardware.

Show More Show Less

OEM Accessory Belt Service Kit - F3X F22/23 N55 3.0L

10X Entries Into Our F80 M3 Sweepstakes

T#:587391

Part#: 11287628661ABKT

In Stock

$ 171.99

This product was last offered at the strikethrough price on
06-09-2026

$ 153.99 USD

Add to Wish List

Qty

$ 153.99 USD

Add to Wish List

This kit includes the basic components recommended to replace when it comes time to swap out your accessory belt.

Blackline Performance Coolant Expansion Tank Cap Cover - BMW M - Red ...

T#:641289

Part#: FXXCET-R

In Stock

$ 65.00 USD

Add to Wish List

Qty

$ 65.00 USD

Add to Wish List

Give the plain plastic factory coolant caps an upgrade with the brand new BLACKLINE Performance Coolant Expansion Tank Cap Cover from Goldenwrench. Each cap is CNC formed from T6 Aluminum and anodized in a limited release race inspired red color. All logos and decorations are finalized through a precision 3D milling process, machined into each cap for the ultimate premium finish. The BLACKLINE Performance Billet Coolant Expansion Tank Cap Cover will fit most BMW vehicles equipped with the N55, S55, S63, and S65 engine with the large coolant tank found in the following vehicles E90/E91/E92 M3 LCI, F22 M235i, F87 M2/M2 Competition, F80 M3, F82 M4, F10/F90 M5, and more (check your coolant cap ensuring that it is the same shape as seen in the product photos). Each kit comes with a Billet Coolant Expansion Tank Cap Cover, and an Installation Instruction Card. This is a not a full cap replacement. The Billet Cap Cover affixes to the top of your factory coolant cap installing easily in minutes.

Show More Show Less

Blackline Performance Oil Cap Cover - Red - BMW M

T#:641286

Part#: FXXOCC-R

In Stock

$ 60.00 USD

Add to Wish List

Qty

$ 60.00 USD

Add to Wish List

Give the plain plastic factory oil cap unit an upgrade with the brand new BLACKLINE Performance Billet Oil Cap Cover. Each cap is CNC formed from T6 Aluminum and anodized in a limited release race inspired red color. Featuring an all new Drip G logo, with the BLACKLINE insignia engraved in the cap handle with a reminder to fill the engine with Synthetic Oil Only. All logos and decorations are finalized through a precision 3D milling process, machined into each cap for the ultimate premium finish. The BLACKLINE Performance Billet Oil Cap Cover will fit most BMW vehicles equipped with the N55, S55, S63, and S65 with the round shaped oil cap found in the following vehicles E90/E91/E92 M3 LCI, F22 M235i, F87 M2/M2 Competition, F80 M3, F82 M4, F10/F90 M5, and more (check your oil cap ensuring that it is the round shape as seen in the product photos). Each kit comes with a Billet Oil Cap Cover, and an Installation Instruction Card. This is a not a full cap replacement. The Billet Oil Cap Cover affixes to the top of your factory oil cap installing easily in minutes.

Show More Show Less

Port Injector Plugs

T#:27171925

Part#: UNI-BMS-PIPLUGS

In Stock

$ 60.00 USD

Add to Wish List

Qty

$ 60.00 USD

Add to Wish List

These dummy injectors fit in place of port injection fuel injectors to block the holes. Allows use to aluminum manifolds with port injection bungs without having to purchase fuel injectors. Plugs are EV14 injectors and measure 38mm or 1.5" from o-ring to o-ring.

Show More Show Less

BMS High Flow Silicone Turbo Inlet - BMW N55 F2X F3X F87

T#:43109033

Part#: BMS-HFSTI-FN55

Back Ordered

$ 199.00 USD

Add to Wish List

Qty

$ 199.00 USD

Add to Wish List

Burger's replacement heavy-duty silicone turbo inlet replaces the narrow and crack-prone factory plastic unit with a higher flowing silicone inlet with billet aluminum fittings. Unlike other inlets, this inlet retains a larger flow straight from intake to turbo for improved boost response and increased turbo efficiency. While beneficial with the factory turbo, this inlet is a must-have with any larger than factory turbo and the perfect complement to the BMS N55 intake systems.

Show More Show Less

Vargas N54/55 Billet Crank Seal Guard - BMW N54 N55 3.0L

2X Entries Into Our F80 M3 Sweepstakes

T#:638889

Part#: VTT-CRANKGUARD

In Stock

Starting at $ 89.99 USD

Add to Wish List

Starting at $ 89.99 USD

Add to Wish List

It is a well-known issue on the BMW N54/55 platforms that your serpentine belt can fail for various reasons. When this happens, there is a high chance of the belt getting sucked behind the front damper pulley and then being pushed past the crank seal into your oil pan. From there it can get sucked into the oil pick up causing total engine failure. Even if you do not lose the engine, it is a COSTLY repair to remove the sub-frame and drop the oil pan to remove the belt. The best way to combat this is to watch for oil leaks and keep up on your maintenance. BUT, even with those preventative measures, pre-mature belt failure can occur. This crank seal guard installs over your front crank seal and will keep the belt from being sucked in if a belt failure does occur. This is a cheap way to ensure you do not end up having to replace your motor from oil starvation due to an ingested belt. Vargas' seal is different from those already on market in two major ways. Firstly, it is not offensively priced. Secondly, it is 100% billet with no welds on the tabs to break, no cheap bent thin steel pieces. 100% Billet 6061-T6 aluminum, anodized black for long-term corrosion resistance. Crank Seal Guard includes: One VTT Billet N54/55 Crank Seal Guard Two extended 12.9 Grade bolts, and two stainless washers We highly recommend you install WITH a crank bolt capture at the same time, as you have to remove the damper anyway. Then you will get the benefit of helping eliminate the dreaded spun crank hub and the crank seal issue

Show More Show Less

Spark Plug Gapper Tool BMS Billet

T#:26404907

Part#: 12MMSPG

In Stock

$ 35.00 USD

Add to Wish List

Qty

$ 35.00 USD

Add to Wish List

Spark Plug Gapper Tool BMS Billet is essential for accurately adjusting the gap of spark plugs. This precision tool ensures that each plug is set to the exact specifications required for optimal engine performance. Made in the USA, it features a 12mm plug thread size, making it suitable for a wide range of applications.

Precision Adjustment: Allows for accurate gap adjustments to ensure optimal spark performance and engine efficiency.
Speed and Efficiency: Streamlines the process of gapping plugs while maintaining high precision, saving time and effort.
High-Quality Construction: Crafted from billet materials for durability and reliability, ensuring long-term use.
Lifetime Replacement Program: Comes with a lifetime replacement guarantee, reflecting confidence in the tool's quality and performance.

Upgrade your spark plug maintenance with the Spark Plug Gapper Tool BMS Billet for a reliable and precise solution.

Show More Show Less

Vargas "Spline Lock" Crank Hub Solution - Includes Crank Bolt Capture...

2X Entries Into Our F80 M3 Sweepstakes

T#:558795

Part#: VTT-CRANKHUB-1

In Stock

$ 889.99 USD

Add to Wish List

Qty

$ 889.99 USD

Add to Wish List

Under certain conditions, the N55 crank hub likes to spin, without warning and even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines which press into the crank, and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and ECS are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution.

Show More Show Less

Blackline Performance Oil Cap Cover - Blue - BMW M

T#:5691134

Part#: FXXOCC-B

In Stock

$ 60.00 USD

Add to Wish List

Qty

$ 60.00 USD

Add to Wish List

Give the plain plastic factory oil cap unit an upgrade with the brand new BLACKLINE Performance Billet Oil Cap Cover. Each cap is CNC formed from T6 Aluminum and anodized in a limited release race inspired blue color. Featuring an all new Drip G logo, with the BLACKLINE insignia engraved in the cap handle with a reminder to fill the engine with Synthetic Oil Only. All logos and decorations are finalized through a precision 3D milling process, machined into each cap for the ultimate premium finish. The BLACKLINE Performance Billet Oil Cap Cover will fit most BMW vehicles equipped with the N55, S55, S63, and S65 with the round shaped oil cap found in a variety of vehicles(check your oil cap ensuring that it is the round shape as seen in the product photos). Each kit comes with a Billet Oil Cap Cover, and an Installation Instruction Card. This is a not a full cap replacement. The Billet Oil Cap Cover affixes to the top of your factory oil cap installing easily in minutes.

Show More Show Less

BLACKLINE Performance Edition RED Fuel Cap Cover

T#:39160626

Part#: F5XFCCR

In Stock

$ 47.00 USD

Add to Wish List

Qty

$ 47.00 USD

Add to Wish List

Blackline Performance Coolant Expansion Tank Cap Cover - BMW M - Blue...

T#:5691129

Part#: FXXCET-B

In Stock

$ 65.00 USD

Add to Wish List

Qty

$ 65.00 USD

Add to Wish List

Give the plain plastic factory coolant caps an upgrade with the brand new BLACKLINE Performance Coolant Expansion Tank Cap Cover from Goldenwrench. Each cap is CNC formed from T6 Aluminum and anodized in a limited release race inspired blue color. All logos and decorations are finalized through a precision 3D milling process, machined into each cap for the ultimate premium finish. The BLACKLINE Performance Billet Coolant Expansion Tank Cap Cover will fit most BMW vehicles equipped with the N55, S55, S63, and S65 engine with the large coolant tank found in a variety of M vehicles(check your coolant cap ensuring that it is the same shape as seen in the product photos). Each kit comes with a Billet Coolant Expansion Tank Cap Cover, and an Installation Instruction Card. This is a not a full cap replacement. The Billet Cap Cover affixes to the top of your factory coolant cap installing easily in minutes.

Show More Show Less

BLACKLINE Performance F Series Washer Fluid Cap - Red

T#:3586293

Part#: FXXWFCR

In Stock

$ 47.00 USD

Add to Wish List

Qty

$ 47.00 USD

Add to Wish List

Full replacement Billet Washer Fluid Cap for BMW F Series vehicles!

GoldenWrench BLACKLINE Performance Oil Filter Housing Cap

T#:7244442

Part#: FXXOFH-R

Ships in 4 Business Days

$ 147.00 USD

Add to Wish List

Qty

$ 147.00 USD

Add to Wish List

OEM factory oil filter housing caps are made of plastic which can be prone to failure over time. Bring form, function and design to your engine with GoldenWrench's highly anticipated 2022 product release. Introducing the BLACKLINE Performance RED Billet Oil Filter Housing Cap which is designed to increase the functioning longevity and improve aesthetics over the factory plastic part while offering superior built in maintenance features.

Show More Show Less

Blackline Performance Oil Cap Cover - Gray - BMW M

T#:641268

Part#: FXXOCC

Ships in 4 Business Days

$ 60.00 USD

Add to Wish List

Qty

$ 60.00 USD

Add to Wish List

Give the plain plastic factory oil cap unit an upgrade with the brand new BLACKLINE Performance Billet Oil Cap Cover. Each cap is CNC formed from T6 Aluminum and anodized with an Anthracite Gray color to compliment the factory engine cover. Featuring an all new Drip G logo, with the BLACKLINE insignia engraved in the cap handle with a reminder to fill the engine with Synthetic Oil Only. All logos and decorations are finalized through a precision 3D milling process, machined into each cap for the ultimate premium finish. The BLACKLINE Performance Billet Oil Cap Cover will fit most BMW vehicles equipped with the N55, S55, S63, and S65 with the round shaped oil cap found in the following vehicles E90/E91/E92 M3 LCI, F22 M235i, F87 M2/M2 Competition, F80 M3, F82 M4, F10/F90 M5, and more (check your oil cap ensuring that it is the round shape as seen in the product photos). Each kit comes with a Billet Oil Cap Cover, and an Installation Instruction Card. This is a not a full cap replacement. The Billet Oil Cap Cover affixes to the top of your factory oil cap installing easily in minutes.

Show More Show Less

BMW F30 Blackline Washer Fluid Cap Performance - Motorsport Blue ...

T#:7355611

Part#: FXXWFC-B

In Stock

$ 47.00 USD

Add to Wish List

Qty

$ 47.00 USD

Add to Wish List

BMW F30 Blackline Washer Fluid Cap Performance - Motorsport Blue

The BMW F30 Blackline Washer Fluid Cap Performance - Motorsport Blue offers a premium upgrade for BMW F Series vehicles. This high-quality billet washer fluid cap features a no-spill seal technology, addressing common issues with washer fluid leakage from the factory reservoir. Designed and manufactured with precision, this cap replaces the factory unit with a stylish and functional enhancement.

Benefits:

No-Spill Seal Technology: Prevents leakage from the factory washer fluid reservoir.
Premium Construction: CNC machined from T6 Aluminum for durability and strength.
Eye-Catching Design: Anodized in Motorsport Blue for a striking appearance.
Precision Finish: Logos and details are 3D milled for a refined look.
Easy Installation: Direct replacement for the factory cap, installs in minutes.
Wide Compatibility: Fits most BMW F Series models (check the application guide).

Show More Show Less

BLACKLINE Performance Fuel Cap Cover

T#:797049

Part#: FXXFCC

Ships in 4 Business Days

$ 47.00 USD

Add to Wish List

Qty

$ 47.00 USD

Add to Wish List

Give your gas cap a much-needed upgrade with the all new BMW M Car Series Billet Aluminum Fuel Cap Cover from Goldenwrench Supply Co. This performance Fuel Cap Cover Kit comes with a Billet Aluminum Fuel Cap Cover, and Installation Instructions. Please note this a cover that affixes on top of your factory fuel cap installing easily in minutes.

Show More Show Less

BLACKLINE Performance Fuel Cap Cover - Motorsport Blue

T#:6635763

Part#: FXXFCC-B

In Stock

$ 47.00 USD

Add to Wish List

Qty

$ 47.00 USD

Add to Wish List

Give your gas cap a much-needed upgrade with the all new BMW M Car Series Billet Aluminum Fuel Cap Cover from Goldenwrench Supply Co. This performance Fuel Cap Cover Kit comes with a Billet Aluminum Fuel Cap Cover, and Installation Instructions. Please note this a cover that affixes on top of your factory fuel cap installing easily in minutes.

Show More Show Less

BMW N54 Port Injection Intake Manifold With 750cc Injectors And Fuel ...

T#:21933055

Part#: N54PIIMINJECT

In Stock

$ 988.00 USD

Add to Wish List

Qty

$ 988.00 USD

Add to Wish List

BMW N54 Port Injection Intake Manifold With 750cc Injectors And Fuel Line Kit - Phoenix Racing is a high-performance upgrade engineered to replace the stock plastic intake manifold on BMW N54 engines. Constructed from durable, lightweight aluminum, this manifold increases airflow and strength, delivering reliable performance for both street and track applications. Integrated with top-mount port injection bungs, this manifold ensures optimal fuel delivery and spray patterns for maximum efficiency. The Phoenix Racing kit includes calibrated 750cc injectors and a plug-and-play fuel line, making it ideal for drivers aiming for high horsepower and seamless installation. Available through Turner Motorsport.

Replaces the factory plastic manifold with high-strength aluminum for increased durability and performance
Supports increased airflow to enhance engine power and efficiency
Integrated top-mount port injection bungs optimize fuel injector spray and delivery
Includes calibrated 750cc injectors and plug-and-play fuel line for a complete port injection solution
Multiple expansion vacuum ports support blow-off valves, boost gauges, Hobb’s switches, and more
High-quality, high-temperature o-rings provide lasting durability and reliability
Exclusively available through Turner Motorsport, ensuring trusted quality and service

Show More Show Less

Valve Cover kit - F22/23 F3X F87 N55 3.0L

10X Entries Into Our F80 M3 Sweepstakes

T#:23913948

Part#: F3XN55VCKT

In Stock

Sale - Save 24% $ 292.99

This product was last offered at the strikethrough price on
05-03-2026

$ 223.72 USD

Add to Wish List

Qty

Sale - Save 24%

$ 292.99

This product was last offered at the strikethrough price on
05-03-2026

$ 223.72 USD

Add to Wish List

If your valve cover has become cracked or warped, replace it with this quality Bavarian Autosport cover to prevent leaks and further valvetrain damage. This kit includes everything needed to install a new valve cover, including a new CCV hose, gaskets, and hardware!

Show More Show Less

Spline Lock Crank Hub Solution W/ Complete Package - N55 S55 ...

2X Entries Into Our F80 M3 Sweepstakes

T#:18733532

Part#: VTT-CRANKHUB-6

Ships in 1 Business Day

$ 986.99

This product was last offered at the strikethrough price on
06-28-2026

$ 939.99 USD

Add to Wish List

Qty

$ 939.99 USD

Add to Wish List

Under certain conditions, the N55 crank hub likes to spin, without warning and even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines which press into the crank, and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and ECS are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution.

Show More Show Less

70c Low Temp Oil Thermostat Kit - N54/N55

10X Entries Into Our F80 M3 Sweepstakes

T#:30031507

Part#: N54N55LTKT1

Back Ordered

Sale - Save 18% $ 152.97

This product was last offered at the strikethrough price on
05-03-2026

$ 125.58 USD

Add to Wish List

Qty

Sale - Save 18%

$ 152.97

This product was last offered at the strikethrough price on
05-03-2026

$ 125.58 USD

Add to Wish List

Upgrade your stock oil cooler thermostat for improved performance. Swap out your existing cover with ease, replacing it with a durable billet cover. Upgrade from your 110-degree Celsius thermostat to a new 70-degree Celsius version for faster oil flow and extended temperature control. With oil temperatures reaching 230 degrees Fahrenheit by the time your factory thermostat opens, initiating oil flow at lower temperatures proves more effective than attempting to cool down already elevated temperatures.

Utilizing a factory-style thermostat, this upgrade can be used in all weather conditions and allows your engine to warm up properly unlike thermostat bypass kits.

Kit contents:

Billet thermostat housing cover
Replacement gasket
Hardware
Lower temperature thermostat - 70c (158F) vs Factory 110c (230F)
Low temp thermostat spring

Show More Show Less

Vargas Ignition Coil Kit (Blue) - N5x

2X Entries Into Our F80 M3 Sweepstakes

T#:5309605

Part#: VTT-COIL-N5X-BLU

In Stock

$ 169.99 USD

Add to Wish List

Qty

$ 169.99 USD

Add to Wish List

Vargas has contacted multiple coil manufacturing companies, paying for individual coils to be made then putting them through rigorous testing in the USA to ensure they matched or exceeded factory output. Once satisfied with the testing, the best performing coils were made to various colors and specs. Vargas is proud to offer a new line of ignition coil replacements for N5x Engines. VTT N5X coils are tested against Delphi 10571 coils which are an upgrade over stock N5X factory coils. The VTT performance matches or exceeds a Delphi 10571 Coil. The coils are offered in a choice of black, red, and blue.

Show More Show Less

Turbocharger Installation Kit - N55 3.0L

10X Entries Into Our F80 M3 Sweepstakes

T#:590423

Part#: TMSTIKN55KT

In Stock

Sale - Save 3% $ 248.08

This product was last offered at the strikethrough price on
06-15-2026

$ 240.64 USD

Add to Wish List

Qty

Sale - Save 3%

$ 248.08

This product was last offered at the strikethrough price on
06-15-2026

$ 240.64 USD

Add to Wish List

Reusing old hardware and gaskets can often lead to oil and exhaust leaks. To prevent this, we have assembled this kit which includes all of the basic components needed to install a turbo upgrade or a re-built turbo on your N55 3.0L.

Show More Show Less

Innovate LC-2 Wideband O2 Controller Kit

T#:28836410

Part#: 38770

In Stock at Vendor

$ 212.99 USD

Add to Wish List

Qty

$ 212.99 USD

Add to Wish List

Features & Benefits:

Two configurable linear 0-5V analog outputs Ability to calibrate O2 sensors for maximum accuracy Includes LC-2 controller and Bosch wideband O2 sensor Comes with a program cable, manual, and a 10 ft. sensor cable Includes a 1-inch mild steel exhaust bung Innovate MTS serial in/out capability Integrated dual-color status LED (green/red) Patented DirectDigital™ wideband sensor control Positive lock connectors for all connections Real-time display data on screen or with the powerful LogWorks software Range:

AFR (Air-Fuel Ratio) range from 7.4:1 to 22.4:1 (0.5 to 1.5 lambda)

Show More Show Less

Iwis Oil Pump Chain

T#:375888

Part#: 11417584079

In Stock

$ 64.99 USD

Add to Wish List

Qty

$ 64.99 USD

Add to Wish List

Should be replaced any time the oil pump is removed or chain noise is detected

Vargas Ignition Coil Kit (Red) - N5x

2X Entries Into Our F80 M3 Sweepstakes

T#:5309610

Part#: VTT-COIL-N5X-RED

In Stock

$ 169.99 USD

Add to Wish List

Qty

$ 169.99 USD

Add to Wish List

Vargas has contacted multiple coil manufacturing companies, paying for individual coils to be made then putting them through rigorous testing in the USA to ensure they matched or exceeded factory output. Once satisfied with the testing, the best performing coils were made to various colors and specs. Vargas is proud to offer a new line of ignition coil replacements for N5x Engines. VTT N5X coils are tested against Delphi 10571 coils which are an upgrade over stock N5X factory coils. The VTT performance matches or exceeds a Delphi 10571 Coil. The coils are offered in a choice of black, red, and blue.

Show More Show Less

Blackline Performance Coolant Expansion Tank Cap Cover - Gray - BMW M...

T#:641288

Part#: FXXCET

In Stock

$ 65.00 USD

Add to Wish List

Qty

$ 65.00 USD

Add to Wish List

Give the plain plastic factory coolant caps an upgrade with the brand new BLACKLINE Performance Coolant Expansion Tank Cap Cover from Goldenwrench. Each cap is CNC formed from T6 Aluminum and anodized with an Anthracite Gray color to compliment the factory engine cover. All logos and decorations are finalized through a precision 3D milling process, machined into each cap for the ultimate premium finish. The BLACKLINE Performance Billet Coolant Expansion Tank Cap Cover will fit most BMW vehicles equipped with the N55, S55, S63, and S65 engine with the large coolant tank found in the following vehicles E90/E91/E92 M3 LCI, F22 M235i, F87 M2/M2 Competition, F80 M3, F82 M4, F10/F90 M5, and more (check your coolant cap ensuring that it is the same shape as seen in the product photos). Each kit comes with a Billet Coolant Expansion Tank Cap Cover, and an Installation Instruction Card. This is a not a full cap replacement. The Billet Cap Cover affixes to the top of your factory coolant cap installing easily in minutes.

Show More Show Less

Delphi - Factory Spec Ignition Service Kit - N55

10X Entries Into Our F80 M3 Sweepstakes

T#:5498500

Part#: 12137594937IGKT

Ships in 3 Business Days

Sale - Save 5% $ 336.99

This product was last offered at the strikethrough price on
07-27-2026

$ 318.59 USD

Add to Wish List

Qty

Sale - Save 5%

$ 336.99

This product was last offered at the strikethrough price on
07-27-2026

$ 318.59 USD

Add to Wish List

If your BMW's mileage is getting up there, be sure to keep your ignition system in check. Whether you currently have a misfire or you're just doing preventative maintenance, this kit is perfect. The kit includes: 6 Delphi Coils with locks 6 Bosch spark plugs BMW spark plug service label for your records 1 packet of American Grease Stick dielectric grease The kit includes: 6 Bremi Coils with locks 6 Bosch spark plugs BMW spark plug service label for your records 1 packet of American Grease Stick dielectric grease

Show More Show Less

VTT Ignition Coil Conversion Kit - S55/N55 To B58 - Multiple Color Op...

2X Entries Into Our F80 M3 Sweepstakes

T#:22196341

Part#: VTTS55CLCNV

Ships in 6 Business Days

Starting at $ 335.99 USD

Add to Wish List

Starting at $ 335.99 USD

Add to Wish List

VTT is proud to offer its very own Game Changer S55/N55 to B58 Coil conversion kit for the BMW S55/N55 platforms. The 55 series of engines has notoriously had ignition problems with the factory coils, while aftermarket upgrades do exist, they can be bulky. The solution is the BMW B58 ignition coils which are extremely robust and can support well over 1000WHP with no issues. This means a plug-and-play affordable solution that fits like stock, and looks AMAZING doing so! We designed our own 6061-T6 Billet bracket in a plethora of colors including matching shades for every S55/N55 Valve Cover. This means you can mix and match the color of the bracket with coil color, with VC color to truly tailor your engine bay to look exactly how you want it to! The kit comes with the following: 3 – Billet Aluminum Coil Brackets in the color of choice 6 – Plug and play VTT wiring harnesses 6 – Custom VTT stalks to convert the B58 coils to the S55/N55 head (We ensure proper spring length inside the boot for optimal spring-to-plug contact) *NOTE: Flash setting changes may be required when installing the conversion kit to ensure the proper function of the B58 coils with S55/N55 DME. This can be found in almost all flashing software settings such as MHD, Bm3, etc.* **NOTE: THESE BRACKETS FIT STOCK S55 VC, VTT S55 BILLET VC, and MOST N55 made after 2011. If you have an older N55 made before 01/2011. These may not fit. Purchase carefully as items that have been installed or attempted to cannot be returned.**

Show More Show Less

OEM Ignition Service Kit - F80/2/3/7 N55 S55

10X Entries Into Our F80 M3 Sweepstakes

T#:556701

Part#: F8XX55TISKT

In Stock

$ 399.99 USD

Add to Wish List

Qty

$ 399.99 USD

Add to Wish List

Often an oversight in maintenance, ignition components are also susceptible to wear and tear. Spark Plugs can accumulate carbon, reducing the spark intensity and it's ability to properly ignite the air/fuel mixture, leading to misfires and generally declining performance.

Show More Show Less

IWIS N55 Engine Oil Pump Chain Kit - BMW E82/88 E9X F3X F25 F26 E70/7...

T#:36981080

Part#: 90001301

In Stock

$ 314.36

This product was last offered at the strikethrough price on
05-04-2026

$ 304.83 USD

Add to Wish List

Qty

$ 304.83 USD

Add to Wish List

Prevent costly failure with this IWIS Engine Oil Pump Chain Kit! This kit contains all of the basic items needed to service your oil pump drive system and prevent failure long before it occurs. Chains can stretch and chain guides and tensioners can wear out, leading to the chain skipping teeth. This prevents the oil pump from being driven at the proper speeds. If not addressed, the chain could begin to "slip" over the gears, failing to drive the oil pump. When this occurs, oil pressure will drop suddenly, failing to properly lubricate sensitive internal engine components such as main bearings, rod bearings, and camshaft ledges and lobes, resulting in severe scoring and eventual engine failure.

Show More Show Less

BLACKLINE Performance F Series Washer Fluid Cap - Gray

T#:4565848

Part#: FXXWFCG

Ships in 4 Business Days

$ 47.00 USD

Add to Wish List

Qty

$ 47.00 USD

Add to Wish List

Full replacement Billet Washer Fluid Cap for BMW F Series vehicles!

IWIS Chain Tensioner - With Gasket Ring - BMW N52 N54 N55 3.0L ...

T#:43378595

Part#: 11317584723

Ships in 2 Business Days

$ 100.99

This product was last offered at the strikethrough price on
05-07-2026

$ 97.99 USD

Add to Wish List

Qty

$ 97.99 USD

Add to Wish List

Over time, your engine timing components begin to wear out. Tensioners weaken, chains can stretch, and timing chain guides can wear down. All of these lead to the possibility of the timing chain jumping teeth on the sprockets, causing your timing to shift. This could result in rough idle and reduced engine power, or even complete engine failure. Prevent damage to your engine with new timing components, such as this IWIS timing chain tensioner. Note, we recommend replacing timing components every 100K miles, or sooner, depending on the condition of the timing components.

Show More Show Less

Top-Tier BMW N54/N55 Ignition Service Kit

10X Entries Into Our F80 M3 Sweepstakes

T#:21670137

Part#: TMSN5SPCOILKT

In Stock

Sale - Save 13% $ 285.99

This product was last offered at the strikethrough price on
05-03-2026

$ 248.31 USD

Add to Wish List

Qty

Sale - Save 13%

$ 285.99

This product was last offered at the strikethrough price on
05-03-2026

$ 248.31 USD

Add to Wish List

Upgrade your BMW N54 and N55 engine with Packaged by Turner kits for optimized performance and fuel efficiency. Our BMW ignition coils feature specialized modifications to boost firepower, delivering increased torque at lower RPMs and more horsepower at higher RPMs. The extent of improvement depends on your engine's current condition, but you'll undoubtedly experience a noticeable difference in performance. Ensure your BMW's engine runs smoothly and efficiently with our comprehensive ignition service kit from ECS Tuning. This kit includes six Bav Auto ignition coils with plug boots, NGK spark plugs, American Grease Stick dielectric grease, and a BMW spark plug service indicator label. Rest assured with a 2-year warranty on all Bavarian Autosport brand parts. Upgrade your BMW N54 and N55 engine's ignition system today for a remarkable driving experience.

Show More Show Less

Spline N55 S55 Lock Crank Hub Solution W/ Hardware Package

2X Entries Into Our F80 M3 Sweepstakes

T#:18733531

Part#: VTT-CRANKHUB-5

Ships in 10 Business Days

$ 880.99 USD

Add to Wish List

Qty

$ 880.99 USD

Add to Wish List

Under certain conditions, the N55 crank hub likes to spin, without warning and even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines which press into the crank, and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and ECS are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution.

Show More Show Less

Improved Racing BMW Oil Cooler Thermostat (180F)

T#:27171935

Part#: IRTHERM

Back Ordered

Starting at $ 318.99 USD

Add to Wish List

Starting at $ 318.99 USD

Add to Wish List

Precise Oil Temperature Control for Your BMW Upgrade your BMW N20, N26, N51, N52, N53, N54, N55, and S55 engine's oil temperature control with Improved Racing's high-performance oil cooler adapter. Designed to address flaws in the factory's restrictive oil cooler adapter and faulty internal flow control valve, this upgrade ensures precise oil temperature control. Improved Racing's thermostat provides quick engine warmup, prevents overcooling, and delivers full oil cooling capacity on demand. Trusted by professional race teams around the globe, Improved Racing's thermostats have proven highly reliable, are backed by a lifetime warranty, and are made in the USA. Option to Use the Factory Oil Cooler and Lines The optional factory oil line adapter allows you to use the factory oil cooler lines for a simple, plug-and-play installation. For maximum performance, the factory oil cooler and lines may be replaced with an aftermarket cooler and AN lines using the AN adapter fittings (-10AN line size is recommended). Please note that some applications, such as most BMW SUV's, use a water-to-oil heat exchangers. These applications require plugging the coolant supply and return ports, as well as adding an external air-to-oil cooler and lines (factory or aftermarket). Please note the Oil cooler adapter cannot be used without an oil cooler.

Show More Show Less

Bosch - Factory Spec Ignition Service Kit - N55

10X Entries Into Our F80 M3 Sweepstakes

T#:556734

Part#: N55TISKT

In Stock

$ 276.99 USD

Add to Wish List

Qty

$ 276.99 USD

Add to Wish List

Often an oversight in maintenance, ignition components are also susceptible to wear and tear. Spark Plugs can accumulate carbon, reducing the spark intensity and it's ability to properly ignite the air/fuel mixture, leading to misfires and generally declining performance. Other ignition components, such as coils, boots, wires, caps, and rotors, can also wear out over time due to factors like heat and contamination, preventing the current from reaching the spark plug.

To start over fresh with all new components, we now offer these Ignition Service Kits. Each kit comes with brand new OE quality components, replacing any potential fault points in your ignition system for peak performance!

See kit contents below for a complete list of included components.

Show More Show Less

Liqui Moly Longtime High Tech Oil Change Kit

10X Entries Into Our F80 M3 Sweepstakes

T#:15644259

Part#: 07119963129-KT

Ships in 2 Business Days

Sale - Save 4% $ 115.98

This product was last offered at the strikethrough price on
08-31-2026

$ 110.86 USD

Add to Wish List

Qty

Sale - Save 4%

$ 115.98

This product was last offered at the strikethrough price on
08-31-2026

$ 110.86 USD

Add to Wish List

To keep your driving machine in top shape, regular maintenance is imperative. BMW's service interval for an oil change varies based on driving habits. We recommend changing your oil after no more than 10,000 miles. A 5,000 oil service interval is preferred for aggressive or city driving. This kit contains Seven Liters of Liqui Moly Longtime High Tech Engine Oil 5w-30 Engine Oil Filter Oil Drain Plug Gasket (Included with filter kit)

Show More Show Less

VTT N5X/S55/N2X Billet BMW Oil Filter Housing Cap - Blue - BMW N52 N5...

2X Entries Into Our F80 M3 Sweepstakes

T#:5122267

Part#: VTTFILTERCAPBLUE

Ships in 5 Business Days

$ 89.99 USD

Add to Wish List

Qty

$ 89.99 USD

Add to Wish List

VTT is proud to offer a billet replacement for the factory plastic Oil filter housing cap. This cap does away with the weak plastic cap and the need for a special tool for removal, while adding some pop and color to your engine bay. These oil filter housing caps retain ALL of the factory provisions for the filter basket, including the lower pins which are important for the proper function of pressure bypass, etc. They also have cooling fins to help with oil temps. Vargas Turbo designed these caps to complement their N5X Billet Oil caps and N5X Billet Power Steering caps so that all 3 will have the same design. The caps are offered in 4 colors – Red, Black, Blue, and Clear anodized

Show More Show Less

BM3 FlexFuel Kit - OEM Fuel Hat Location - BMW F-Series S55/N55 3.0L ...

T#:33746522

Part#: BM3FFKTF55

Ships in 10 Business Days

$ 599.00 USD

Add to Wish List

Qty

$ 599.00 USD

Add to Wish List

We are proud to bring out this truly awesome product that makes getting the required Flex Fuel hardware on your BMW and A9X Supra with incredible ease and minimal effort, in your own driveway.

Our kit is entirely plug-and-play with the factory vehicle harness. No cutting or splicing of OEM wiring/connectors. It installs in minutes and can be removed without a trace on the car!

Our team used SolidWorks to design a Flow Optimized Flex Fuel Sensor Adapter (FFSA) to ensure fuel flow is unobstructed and with no added pressure drop at full fuel pump flow from the fuel tank to your motor when our kit is installed. This is important when pushing the factory fuel system with all the power Ethanol can provide over petrol!

Flex fuel sensor housing is designed to neatly install into the factory BMW fuel hat location.

Flex Fuel Sensor Adapter also contains two 1/8 NPT ports that allow installation of an auxiliary Fuel Pressure sensor for vehicles that don’t come with an OEM one from the factory for future use. Depending on fitment, either port can be used.

Install the bootmod3 Flex Fuel Plug and Play Kit and flash your flex fuel enabled bootmod3 OTS MultiMap or Custom Map in minutes and you’re off to the races never worrying about alcohol/petrol blend % in your fuel tank. It does not get better or easier than this!

bootmod3 FlexFuel Plug and Play Kit:

Minutes to install at home as opposed to hours at a shop with car up on lift fabricating/cutting into factory fuel lines and splicing/cutting/pinning into OEM electrical
4+ hours in time/cost savings to get going on Flex Fuel as compared to most other kits that require making custom fuel lines, fittings and custom wiring!
Fully reversible/removable and back to stock without a trace in minutes
Custom 3-piece Aluminum-6061 Flex Fuel sensor adapter with built-in sensor bypass to allow for obstruction free fuel flow made to fit in the vehicle factory fuel hat area below the rear seat
All connecting points sealed with fuel safe Viton o-rings
Flex Fuel Sensor Adapter housing provides additional 1/8 NPT ports for optional Fuel Pressure sensor addition to vehicles without a factory one for bootmod3 CustomROM v2 support
CANBUS Enabled Ethanol Content Analyzer (ECA) that integrates with bootmod3 CustomROM for complete and seamless conversion of your BMW to FlexFuel for bootmod3 Flex Fuel enabled OTS MultiMaps and custom tunes with your bootmod3 tuner of choice
Power/CANBus 4-wire plug and play harness
- 100% Fully Plug and Play harness to the BMW Fuel Controller connectors (EKP3) on S55, N55 vehicles
- 100% Fully Plug and Play harness on the BMW Body Domain Controller (BDC/FEM) connector on Gen1 F-series B48/B58
Continental Flex Fuel sensor 3-wire harness
Custom Aluminum-6061 CANBus Enclosure for the bootmod3 ECA board
Custom, kink-free teflon braided line allowing plug and play installation with the OEM fuel hat and factory 5/16” or 3/8” fuel feed line. No cutting or new lines required.
-6 AN fitting by Racetronix

OEM FUEL HAT LOCATION KIT IS INTENDED FOR OEM FUEL PUMP AND ASSOCIATED WIRING. ANY VARIATIONS TO FUEL LINES OR FUEL PUMPS MAY NOT BE COMPATIBLE. USE THE ENGINE BAY INSTALLATION KIT WHERE AVAILABLE INSTEAD.

Show More Show Less

VTT N5X/S55/N2X Billet BMW Oil Filter Housing Cap - Clear - BMW N52 N...

2X Entries Into Our F80 M3 Sweepstakes

T#:5122266

Part#: VTTFILTERCAPCLR

Ships in 1 Business Day

$ 89.99 USD

Add to Wish List

Qty

$ 89.99 USD

Add to Wish List

VTT is proud to offer a billet replacement for the factory plastic Oil filter housing cap. This cap does away with the weak plastic cap and the need for a special tool for removal, while adding some pop and color to your engine bay. These oil filter housing caps retain ALL of the factory provisions for the filter basket, including the lower pins which are important for the proper function of pressure bypass, etc. They also have cooling fins to help with oil temps. Vargas Turbo designed these caps to complement their N5X Billet Oil caps and N5X Billet Power Steering caps so that all 3 will have the same design. The caps are offered in 4 colors – Red, Black, Blue, and Clear anodized

Show More Show Less

BMW F Series BLACKLINE Performance Oil Filter Housing Cap

T#:30364175

Part#: FXXOFH

Ships in 4 Business Days

$ 147.00 USD

Add to Wish List

Qty

$ 147.00 USD

Add to Wish List

Replace your factory plastic oil filter housing cap, which is prone to failure over time, with the BLACKLINE Performance BMW F Series Billet Oil Filter Housing Cap. This upgrade enhances the form, function, and design of your engine bay. Designed to outlast and improve upon the stock plastic part, this cap also offers superior built-in maintenance features. Meticulously designed and manufactured in-house with a completely new form factor, the cap provides significant functional and design improvements over the original. Each cap is CNC-machined from T6 aluminum and finished with a hard anodized coating in our signature anthracite grey color. The precision post-3D milling process engraves all text decorations, ensuring a premium finish. The BLACKLINE Performance Billet Oil Filter Housing Cap is compatible with most BMW F series vehicles equipped with S55 and most N Series engines that use BMW Part 11427525334, including the OG M2, M2 Competition, M3, M4, and many others. Each kit includes a Billet Oil Filter Cap and an Installation Instruction Card. This is a plug-and-play full replacement unit. Upgrade your engine's performance and appearance with this essential enhancement.

Show More Show Less

Project Cars

SELECT YOUR BMW

BMW Engine Parts for BMW F87 M2 N55 3.0L

Sub-Categories

BMW F30 Blackline Washer Fluid Cap Performance - Motorsport Blue

Benefits:

Select Vehicle

Purpose

Category

Brand

Price

Special Offers

Shipping

Narrow Results