BMW Engine Parts for BMW X5 M S63 4.4L

The oxygen sensor is vital to the performance and drivability of your car. The engine computer relies on data from the sensor to make adjustments in engine efficiency and performance. When your BMW oxygen sensor fails, the computer can no longer sense the air/fuel ratio, so it ends up guessing -- resulting in poor performance, poor gas mileage, and increased pollution. Make sure your BMW engine performs as it should, and doesn't use more fuel than it needs to, by simply changing your oxygen sensor today. There is no lifespan on O2 sensors but there are several fault codes that indicate a failed sensor (O2 monitoring, cat efficiency, O2 heating circuit, O2 readiness, and others). The O2 sensor is heated and has a self-calibration feature so once you get the codes or feel performance has suffered, a new sensor is a good starting point to get you back to peak performance.

This is a Bosch O2 sensor - also known as a Lambda probe. Bosch is an OEM supplier to BMW.

Position: after the catalytic converter (post-cat).

This item fits the following BMWs:
2008-2013 E90 E92 E93 BMW M3 Sedan, Coupe, Convertible

If your battery cables have become worn or frayed, or the IBS sensor has gone bad, its time for a replacement. BMW use the IBS, or Intelligent Battery Sensor, to determine not only the state of charge but also the batteries health and life expectancy. Using this data the car's charging system can appropriately supply the battery with the correct voltage, no matter the age.

Comes as a single cable with terminal and IBS Sensor pre-installed.

A faulty camshaft position sensor will result in timing issues and rough idle/engine operation or light up the check engine light. Get rid of your check engine light and restore smooth operation with this OEM VDO sensor.

OEM VDO is one of the largest OE providers in the world, supplying numerous vehicle brands, including BMW, with many of their genuine parts that build the vehicle before they ever reach the car lot. Entrusted by many of the top names in automotives and with their proven history of reliability, it makes all of us here at Turner confident that their line of OEM replacement parts are a perfect option to restore your vehicles original operation and performance. The same great quality or higher than Genuine BMW parts at a lower cost.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

Maintaining proper oil levels in your engine is crucial for peak performance. Undetected leaks can cause your oil to drop to dangerously low levels between oil changes, leading to severe engine damage.

One common culprit for oil leaks is the valve cover. Over time, exposure to extreme temperature fluctuations can wear down the gaskets, causing them to fail. Prevent oil leaks and protect your engine by replacing these vital components.

Comprehensive Kit Includes:

Valve Cover Gasket Set - Left & Right High Pressure Fuel Pump Gasket (2) O-Ring Seals (6) Torx Screws (6) Replace your old gaskets with our high-quality kit to keep your engine running smoothly and efficiently.

If your engine has higher mileage, don't neglect rod bearing replacement! These bearings are sandwiched between the connecting rod and crankshaft journal and are prone to failure due to overheating, lack of lubrication, or general wear. Replace your rod bearings and prevent a spun bearing.

Starting with ACL’s high-performance bearing shells, our Race Series bearings are built to withstand extreme RPMs and stress. Utilizing a "Duraglide" tri-metal construction and a high-strength overlay plate, these bearings offer superior oiling and heat resistance for high-RPM operation.

Our WPC-treated bearings take ACL’s already impressive design and enhance it even further. The WPC treatment process strengthens and smooths the bearing surface by firing high-speed, ultra-fine particles at the bearing shells, reducing friction and improving durability. This advanced surface treatment ensures smoother operation and improved heat dissipation, which are critical for any high-performance engine.

Kit includes

Turner Motorsport WPC-Treated Race Series Rod Bearing Shells (16) Genuine BMW Connecting Rod Bolts (16) Hardware for Oil Pan & Oil Sump Oil filter Liqui-Moly Molygen 5W-40 (6L) Drain Plug Turner Motorsport Oil Reminder Sticker Oil pan gasket RedLine assembly lube (4 oz.)

Key components to help get your install done easily and effectively. Get your car running right again!

Kit includes:​

• All required gaskets and o-rings
• All exhaust and downpipe gaskets
• T-bolt clamps
• 1gal of Coolant