BMW F97 X3 M S58 3.0L

• 70MM, 80MM, OR 90MM OVERALL LENGTH
• OUR HIGHEST-GRADE PREMIUM WHEEL STUD
• DRY LUBE WITH BLACK M-PHOSPHATE COATING
• STUD FOR RACE/TRACK USE
• CORRECT SHOULDER SIZE FOR A WIDE RANGE OF HUBS/BRAKE ROTORS
• USE WITH 14x1.5 NUT
  
• For the very best in a race-grade wheel stud, stop looking! These are the wheel studs that our race teams insist on (after years of trying every stud design on the market). MSI Racing specializes in hardware for motorsport use (NASCAR and IMSA) and other advanced industries. We tried them on our Grand-Am/IMSA racecars and were very impressed by the performance and durability of their designs. Race wins and championships can come down to the seconds of a pitstop. We could run any wheel stud in the world and we use these. After testing them over the course of a few endurance seasons we decided to offer them to all of our customers as well.
  
  These studs are available in three overall lengths - 70.5mm, 80.5mm, and 90.5mm. All sizes are made with aircraft quality alloy steel and have roll formed threads for greater strength than cut threads. We use a dry film lubricant HM-30 coating containing Teflon & Moly over a manganese phosphate finish. Manganese is preferred over the more common zinc because it's better at reducing friction and wear to prevent thread galling. With the dry lube applied over the phosphate this is the best corrosion resistance we have seen in any wheel stud! Salt tests have shown this stud is superior to others in corrosion resistance. The dry lube helps the nut engage and glide over the threads for faster engagement without cross threading or binding. Other features of our MSI studs include a large bullet nose nut-starter and a properly sized shank to work with a wider range of BMW wheel, nut, and brake rotor combinations. We intentionally avoid the extra large shoulders you see on other studs because they can interfere with some brake rotor hats. The extra large shoulder can be too large to allow the rotor to pass through and drilling out the holes is required (not cool!) Our studs have the sufficient shank for the brake rotor without interfering.
  
  We configured these studs to have a 14x1.25 thread to go into the wheel hub. But the exposed stud has 14x1.5 threads. We did this because threading a nut is faster on 1.5 threads than a finer 1.25 thread pitch, which saved us time during pitstops. There are also more wheel nut options in 14x1.5. When you order our 14x1.25 studs make sure you also order the 14x1.5 nuts.
   

  FREE red threadlocker with purchase of a full set of wheel studs (16 or more)MSI Dry Lube Bullet Nose Wheel Stud Features:
  

• Dry film lubricant HM-30 coating containing Teflon & Moly over a manganese phosphate finish
• Innovative nut-starter and bullet shape radius that all but eliminates cross-threading
• Properly sized shank to work with a wide range of brake rotor, wheel, and nut combinations
• Heat-treated aircraft quality alloy steel
• Developed from over 20 years of top level NASCAR use
  
• These studs are installed using the traditional 'double-nut' method (one regular nut and one jam nut) with thread locking compound (Red Turbo-Lock or similar).
  
  Sold per stud.
  Wheel nuts sold separately.

BFI Center Cap Adapters For BBS E88 Wheels - Brushed - Set of Four are designed to enhance the appearance of BMW's BBS E88 wheels by covering the open center hole with a sleek, brushed finish. These adapters:

• Provide a polished, high-quality look by covering the open center hole
• Are machined from 6061-T5611 aluminum for superior strength and durability
• Feature a hand-brushed finish for a seamless OEM appearance
• Allow the use of 3-prong 70.6mm BBS center caps to add a touch of class
• Are sold in sets of four, with center caps not included

52mm Prosport Electrical Boost Gauge - Clear Lens/White LED is an essential tool for any supercharged or turbocharged vehicle. This precision gauge allows drivers to monitor boost levels with accuracy and style, ensuring peak performance and optimal engine tuning.

• Accurate Boost Monitoring: Provides precise readings of boost pressure, essential for maintaining peak performance.
• Clear Lens: Offers a clear view of gauge readings under various lighting conditions.
• White LED Backlighting: Ensures easy readability and a stylish appearance, even in low-light environments.
• Durable Construction: Built to withstand high-performance conditions and continuous use.
• Easy Installation: Designed for straightforward installation with included mounting hardware.

The NOCO GBC010 12V Accessory Kit is designed to connect directly to the XGC IN and OUT ports of NOCO Boost jump starters. This kit allows you to effortlessly power your preferred 12-volt devices directly from a GB70, GB150, GB250+, GB251+, or GB500+, such as a tire inflator, vacuum, coffee maker, fan, cooler, and more. Constructed from high-conductivity 16AWG 100% copper wire, it boasts a rated capacity of 15 amperes.

Features: 

• Recharge NOCO Boost UltraSafe Lithium Jump Starters from a vehicles 12-volt power source.
• Compatible with NOCO Boost UltraSafe Lithium Jump Starter models GB70, GB150 GB250+, GB251+ and GB500+.
• Power 12-volt device like a tire inflator, vacuum and more.
• High-conductivity 16 AWG copper wire and rated capacity of 15-amperes.
• Molded strain reliefs prevent unwanted strain on the XGC wire connections.

WARNING: This product contains chemicals known to the state of California to cause cancer, birth defects, and/or reproductive harm. See above warning label as well as http://www.p65warnings.ca.gov for further information on Proposition 65 warnings.

The GENPRO10X2 is an upgraded version of our GEN2 with enhanced features. This model is 19% smaller yet delivers 33% more power, making it one of the most high-performing onboard marine battery chargers NOCO has ever produced. It's a two-bank onboard battery charger with a 20-amp rating (10 amps per bank) designed for 12-volt batteries, including marine, boat, starter, and deep-cycle batteries. You can independently charge and control each battery bank using selectable charging modes such as 12V, 12V AGM, 12V Lithium, and 12V Repair Mode, suitable for all types of lead-acid and lithium-ion batteries.

Features: 

• A two-bank on-board battery charger rated at 20-amps for 12-volt batteries, including marine, boat, starter, and deep-cycle batteries.
• Independently charge and control each battery bank with selectable charging modes - including 12V, 12V AGM, 12V Lithium, and 12V Repair Mode - for all types of lead-acid batteries.
• An integrated thermal sensor detects the ambient temperature and alters the charge to eliminate over-charging in hot climates and under-charging in cold climates.
• Charges batteries as low as 1-volt. Or use the all-new force mode that allows you to take control and manually begin charging dead batteries down to zero volts.
• Automatically detects battery sulfation and acid stratification to restore lost battery performance for stronger engine starts and extended battery life.
• It's not just a trickle charger; it's an advanced battery maintainer. A fully automatic, worry-free battery charger for everyday use - 24/7 - with zero overcharge.
• A simplified mounting system allows for quick and easy installations in any direction - even up-side-down - with an integrated anti-vibration backing to isolate shock, vibration, and noise.
• A fully-sealed and waterproof onboard battery charger with an ingress protection rating of IP68, but has survived brutal life cycle testing, including thousands of hours underwater.

WARNING: This product contains chemicals known to the state of California to cause cancer, birth defects, and/or reproductive harm. See above warning label as well as http://www.p65warnings.ca.gov for further information on Proposition 65 warnings.

APR Black Valve Stem Caps are a stylish and functional upgrade for your vehicle's wheels. Sold as a set of four, these high-quality aluminum caps feature an engraved APR logo on each cap. Designed to add a touch of customization to your vehicle, they also serve a practical purpose.

• Premium Quality: Made from durable aluminum for long-lasting performance.
• Enhanced Aesthetics: Features an engraved APR logo for a sleek and stylish look.
• Functional Design: Helps protect valve stems from dirt and moisture.
• Easy Installation: Simple to install and compatible with most standard valve stems.

Upgrade your vehicle with APR Black Valve Stem Caps to enhance both style and functionality.

The X-Connect Eyelet Terminal enables swift connection of a battery charger to any battery. Whether you need to replace a lost connector or permanently affix one on your motorcycle, ATV, snowmobile, personal watercraft, lawn mower, or similar equipment, this terminal makes charging hassle-free.

Features:

• Permanently mount a battery connection to any battery.
• Lie-flat design for seamless installations with M6 (1/4-inch) hole size.
• Built-in fuse protection for increased safety.
• More ways to charge with plug-n-play accessory changes.
• Rugged, watertight connector for extreme environments.
• For larger battery applications, use the GC008 XL Eyelet Connector with a M10 (3/8-inch) hole size.

WARNING: This product contains chemicals known to the state of California to cause cancer, birth defects, and/or reproductive harm. See above warning label as well as http://www.p65warnings.ca.gov for further information on Proposition 65 warnings.

The EVO series from ProSport Gauges is an award winning, industry leading option for those looking to push their car's limits. They allowing you to monitor crucial engine functions in one quick glance with advanced precision. Featuring a dual color readout, you can customize your readout to your liking. Offering a user friendly readout with a digital reading in the center with a bar-graph style sweep around the gauge as well. 

Kit Includes:

• Digital Fuel Pressure Guage (0-100 PSI) 
• Instructions
• Premium fuel sender
• Mounting hardware
• Decals
• Blue or red display

The GENIUS2X4 represents a pinnacle of power, performance, energy efficiency, and compactness in our lineup. This advanced charger features four banks for both 6-volt and 12-volt batteries, serving as a charger, maintainer, trickle charger, and battery desulfator. With an impressive 8-amp rating (2 amps per bank), it caters to all lead-acid and lithium-ion battery types, including flooded, gel, AGM, marine, and deep-cycle variants.

Features:

• A four-bank battery charger maintainer rated a 8-amps - 2-amps per bank with a 40Ah capacity range - designed to charge and maintain multiple vehicles like cars, motorcycles, boats, ATVs, RVs, lawnmowers, trucks, and more.
• Designed for 6-volt and 12-volt lead-acid automotive, marine, and deep-cycle batteries, including flooded, gel, AGM, and maintenance-free, plus lithium-ion batteries.
• An integrated thermal sensor detects the ambient temperature and alters the charge to eliminate over-charging in hot climates and under-charging in cold climates.
• Charges batteries as low as 1-volt. Or use the all-new force mode that allows you to take control and manually begin charging dead batteries down to zero volts.
• Automatically detects battery sulfation and acid stratification to restore lost battery performance for stronger engine starts and extended battery life.
• It's not just a trickle charger; it's an advanced battery maintainer. A fully automatic, worry-free battery charger for everyday use - 24/7 - with zero overcharge.

WARNING: This product contains chemicals known to the state of California to cause cancer, birth defects, and/or reproductive harm. See above warning label as well as http://www.p65warnings.ca.gov for further information on Proposition 65 warnings.