5150 Autosport BMW Internal Engine Parts

Athena Cut Ring Head Gasket - 84.5mm - BMW M50 M52 (84mm Bore) ...

affirm Starting At 0% APR - Subject To Eligibility. See Lending Terms

T#:26171655

Part#: ATH-HG-CR-M50-84

Ships in 1 Business Day

$ 324.99 USD

Add to Wish List

Qty

$ 324.99 USD

Add to Wish List

Upgrade your BMW engine's performance with the Athena Cut Ring Head Gasket. This gasket replaces BMW part # 11121726619 and 11121726617 and is specifically designed for M50 & M52 iron block inline 6-cylinder engines found in E34/E36 chassis. Standard OEM & MLS gaskets can only handle a certain amount of cylinder pressure before they start to leak, making the Athena Cut Ring Head Gasket the recommended choice for applications making 16+ psi. A compression leak passing the head gasket can cause a range of issues, including engine overheating, loss of power, misfires, and in severe cases, catastrophic engine failure. Athena's gasket is crafted with premium quality reinforced M0115, an asbestos-free material that's original equipment approved and renowned for its superior quality. The AISI 304 stainless steel Cooper Rings bite into the aluminum head, providing maximum sealing capabilities around the cylinder bore and optimizing engine performance, even on engines with nitrous and/or turbo applications that exceed 2-bar boost. Before installation, it is crucial to have the mating surfaces of the cylinder head and block professionally cleaned and resurfaced to ensure they are completely flat. Please be aware that the gasket should have a size that is 0.5mm to 1mm larger than the piston. For example, if the piston measures 84mm, then the gasket should be the next size up, either 84.5mm or 85mm. Installation instructions: Make sure that the engine block and cylinder head surfaces are clean, flat, and free from any debris, oil, or coolant. Install the Cut Ring gasket on the engine block and ensure that it is properly aligned. Avoid twisting or bending the gasket during installation. Place the cylinder head on top of the gasket and install the head bolts or studs in their correct positions. Follow the manufacturer's recommended torque specifications and tighten the bolts or studs in the proper sequence to ensure even clamping force across the gasket. After the initial tightening, re-torque the head bolts or studs after the engine has been started and then allowed to cool to room temperature. This will ensure that the gasket is properly seated and compressed. It is recommended to not use any additional sealant on the MLS gasket, as it is already coated with a Viton rubber sealant. Using additional sealant can hinder the performance of the gasket.

Show More Show Less

Ferrea High Performance Valve Spring Kit for BMW N55/S55

affirm Starting At 0% APR - Subject To Eligibility. See Lending Terms

T#:23416526

Part#: FER-HPVSK-N55

Ships in 4 Business Days

$ 1,049.99 USD

Add to Wish List

Qty

$ 1,049.99 USD

Add to Wish List

Maximize your N55 or S55 engine's performance with Ferrea Valve Springs and Retainers, precision components crafted from chromoly alloy. These springs undergo special thermal treatment, ensuring exceptional durability even in extreme racing conditions. Addressing issues like valve binding, breakage, and float, Ferrea valve springs are meticulously heat-treated and stress-relieved, providing stability for high-lift and high-RPM racing engines while minimizing load loss. Precision CNC machined titanium retainers offer superior strength and stability. Ferrea's Spring Seat Locators, made from 4140 chromoly alloy, guarantee precise tolerances and a flat, parallel spring pad with a hard Nitride surface treatment for exceptional toughness and anti-wear characteristics. Please note that installation requires the expertise of an engine builder.

Show More Show Less

Performance Rod Bearing Kit - S54

affirm Starting At 0% APR - Subject To Eligibility. See Lending Terms

T#:26171617

Part#: 5150-HPRBK-S54-E

Back Ordered

$ 669.99 USD

Add to Wish List

Qty

$ 669.99 USD

Add to Wish List

Now one of 5150's best sellers has gotten even better! With a 5150 Autosports' complete High-Performance Rod Bearing Kit, you get all the parts you need to easily swap out the factory connecting rod bearing shells and bolts in one simple kit. 5150's S54 bearings are embraced by BMW engine builders worldwide. Popular for both forced induction and N/A builds, their coated bearings are "friction resistant" making thermal breakdowns that can occur due to lack of lubrication a much less common occurrence. Helping to prevent premature engine failures on street cars, and spun bearings under stress at the track when things are most critical. Proven by customers to help you finish the race even with loss of oil pressure! Kit includes: (1) Complete set of ARP S54 Connecting Rod Bolts (1) Complete set of 5150 High Performance Rod Bearing Set (1) ARP Assembly Lubricant packet Tech Notes: As with all bearings, please check your tolerances and size before installation. Due to the specialized tools needed, professional install recommended. There are no returns available on any engine bearings.

Show More Show Less

M60 Cut Ring Head Gasket Set By Athena-SCE (Bore 90.6 Mm - 0.079") ...

affirm Starting At 0% APR - Subject To Eligibility. See Lending Terms

T#:37149882

Part#: HG-CR-M60-906079

Ships in 3 Business Days

$ 399.99 USD

Add to Wish List

Qty

$ 399.99 USD

Add to Wish List

Turner Motorsport offers the M60 Cut Ring Head Gasket Set By Athena-SCE (Bore 90.6 Mm - 0.079"), providing BMW owners with a premium solution to boost engine reliability and performance.

Performance N55 Main Bearing Set

affirm Starting At 0% APR - Subject To Eligibility. See Lending Terms

T#:26238415

Part#: 5150-HPMBS-N55

Ships in 3 Business Days

$ 549.99 USD

Add to Wish List

Qty

$ 549.99 USD

Add to Wish List

5150 High Performance Coated Main Bearing Sets are made for the demands of high performance engine builds. Treated shells and coated by Calico to reduce friction, these bearings allow your engine to generate more power and resist "spinning" under stress. These coated bearings also have thermal resistant properties that not only perform in high HP applications like forced induction or race use, but also help prevent sudden engine failure in the event of oil pressure loss. 5150 bearings have proven themselves on and off the track, lasting longer and outperforming other bearings on the market.

Show More Show Less

Performance M5X Main Bearing Set

affirm Starting At 0% APR - Subject To Eligibility. See Lending Terms

T#:26171649

Part#: 5150-HPMBS-M50

Ships in 3 Business Days

$ 299.99 USD

Add to Wish List

Qty

$ 299.99 USD

Add to Wish List

5150 High Performance Coated Main Bearing Sets are made for the demands of high performance engine builds. Treated shells and coated by Calico to reduce friction, these bearings allow your engine to generate more power and resist "spinning" under stress. These coated bearings also have thermal resistant properties that not only perform in high HP applications like forced induction or race use, but also help prevent sudden engine failure in the event of oil pressure loss. 5150 bearings have proven themselves on and off the track, lasting longer and outperforming other bearings on the market. Tech Notes: As with all bearings, please check your tolerances and size before installation. Due to the specialized tools needed, professional install recommended.

Show More Show Less

ARP Head Stud Kit - BMW N55/S55

affirm Starting At 0% APR - Subject To Eligibility. See Lending Terms

T#:23416542

Part#: ARP-HSK-S56-CA

In Stock

$ 999.99 USD

Add to Wish List

Qty

$ 999.99 USD

Add to Wish List

BMW M54 Main Bearing Performance Set

affirm Starting At 0% APR - Subject To Eligibility. See Lending Terms

T#:26171610

Part#: 5150-HPMBS-M54

Ships in 3 Business Days

$ 274.99 USD

Add to Wish List

Qty

$ 274.99 USD

Add to Wish List

BMW M54 Main Bearing Performance Set is engineered to meet the rigorous demands of high-performance engine builds. Designed by Turner Motorsport, these high-performance coated main bearings offer enhanced durability and efficiency for engines subjected to extreme conditions.

High-Performance Coating: Treated with a specialized coating by Calico, these bearings reduce friction and prevent "spinning" under high stress, making them ideal for high-power applications.
Enhanced Power Generation: The coating allows the engine to generate more power while maintaining reliability, even under demanding conditions.
Thermal Resistance: Built to withstand high temperatures and perform effectively in forced induction and race applications, these bearings help prevent engine failure due to oil pressure loss.
Proven Durability: Tested extensively on and off the track, 5150 bearings are known for their longevity and superior performance compared to other bearings on the market.

Upgrade to the BMW M54 Main Bearing Performance Set from Turner Motorsport for a robust solution that enhances engine reliability and performance.

Show More Show Less

BMW M60 / M62 Performance Valve Kit

affirm Starting At 0% APR - Subject To Eligibility. See Lending Terms

T#:37149881

Part#: MAN-HPVK-M60

Ships in 3 Business Days

$ 1,199.99 USD

Add to Wish List

Qty

$ 1,199.99 USD

Add to Wish List

Turner Motorsport offers the 5150 Auto Sport M60 / M62 Performance Valve Kit, providing BMW owners with a high-quality solution to maximize engine performance and reliability.

BMW S58 3.0L ARP Head Stud Kit - CA625+

affirm Starting At 0% APR - Subject To Eligibility. See Lending Terms

T#:22427036

Part#: ARP-HSK-S58-CA

Ships in 3 Business Days

$ 999.99 USD

Add to Wish List

Qty

$ 999.99 USD

Add to Wish List

BMW S58 3.0L ARP Head Stud Kit - CA625+ is the ultimate upgrade for the BMW S58 engine, specifically designed for high-performance models such as the F97 X3M, F98 X4M, G80 M3, G82 M4, G83 M4, and G87 M2. Manufactured by Turner Motorsport, this head stud kit ensures optimal engine reliability and performance.

Enhanced Strength: Featuring Custom Age 625+ material with a tensile strength of 260 ksi, this kit provides superior strength compared to factory bolts.
Prevents Head and Block Separation: Designed to handle increased boost levels and high-stress conditions, preventing potential head and block separation.
Precision Engineering: ARP’s advanced manufacturing process ensures that these head studs outperform standard factory bolts under extreme conditions.
Ideal for High-Performance Builds: Perfect for enthusiasts pushing the limits of their S58 engines, offering unparalleled durability and reliability.
Direct Fit: Specifically tailored for the turbocharged inline 6-cylinder BMW S58 engine, ensuring a seamless installation and optimal performance.

Show More Show Less

CP-Carrillo Connecting Rod Set - N63/S63 Pro-Xtreme

affirm Starting At 0% APR - Subject To Eligibility. See Lending Terms
For Use With Aftermarket Pistons Only!

T#:26238404

Part#: CAR-CRS-S63-XT

Ships in 3 Business Days

$ 2,899.99 USD

Add to Wish List

Qty

$ 2,899.99 USD

Add to Wish List

5150 AutoSport Pro-Xtreme Connecting Rods, manufactured by CP-Carrillo, are designed to handle extreme horsepower and high RPM applications for BMW N63 and S63 Engines. The Pro-Xtreme design is specifically tailored to handle up to 2000 horsepower, making them suitable for high-performance turbo/drag racing or street/strip applications. They are also designed to handle high engine speeds of up to 9500 RPM, which is necessary for achieving maximum power output. Each connecting rod is precisely engineered to meet the demands of high-performance engines using advanced manufacturing techniques such as computer-aided design (CAD) and finite element analysis (FEA). The Pro-Xtreme Connecting Rods are designed to be durable, reliable, and capable of handling the extreme stresses and forces generated by high-horsepower and high-rpm engines.

Show More Show Less

BMW N55 S55 Ferrea High Performance Valve Kit

affirm Starting At 0% APR - Subject To Eligibility. See Lending Terms

T#:23416508

Part#: FER-HPVK-S55-T-3

Ships in 4 Business Days

$ 929.99 USD

Add to Wish List

Qty

$ 929.99 USD

Add to Wish List

Increase the power output of your N55/S55 engine with the high-performance Ferrea valve kit. Renowned as the industry's most reliable extreme-duty valves, they're meticulously crafted from aerospace-grade alloys, employing an exclusive two-step slow forging process for optimal grain flow and material structure integrity. A 48-hour heat treatment and stress-relieving process enhance molecular integrity. The valves feature avionics-quality hard chrome and a specially applied hard tip. Standard size: 32mm intake / 28mm exhaust, with a triple groove valve design. Compatible with factory valve locks ("Valve Keepers"), the kit includes 12x Intake Valves and 12x Exhaust Valves for a comprehensive engine upgrade!

Show More Show Less

CP-Carrillo Pro-Xtreme Connecting Rod Set - BMW N63/S63

affirm Starting At 0% APR - Subject To Eligibility. See Lending Terms

T#:23681818

Part#: CAR-CRS-S63-XTT

Ships in 3 Business Days

$ 2,999.99 USD

Add to Wish List

Qty

$ 2,999.99 USD

Add to Wish List

Tailored for exceptional performance, the Pro-Xtreme design is crafted to handle up to 2000 horsepower and 9500 RPM. Constructed from high-strength, aircraft-grade steel, these connecting rods feature a tapered small-end, allowing them to be paired with your OEM pistons.

Show More Show Less

CP Forged Piston Set - N63 - Pro-Xtreme 9.5:1

affirm Starting At 0% APR - Subject To Eligibility. See Lending Terms

T#:26238409

Part#: CP-FPS-N63-XT-HD

Ships in 3 Business Days

$ 2,464.99 USD

Add to Wish List

Qty

$ 2,464.99 USD

Add to Wish List

The 5150 AutoSport Pro-Xtreme Forged Pistons, made by CP-Carrillo, are designed to handle extreme horsepower and high RPM applications for BMW N63 engines. Constructed from high-strength, aircraft-grade steel, these pistons are engineered to withstand the forces generated by high-powered engines. The Pro-Xtreme Piston design is specifically engineered to handle up to 2000 horsepower, making these pistons suitable for high-performance turbo/drag racing or street/strip applications. They are also designed to handle high engine speeds of up to 9500 RPM, which is necessary for achieving maximum power output. Each piston is precisely fabricated to meet the demands of high-performance engines using advanced manufacturing techniques such as computer-aided design (CAD) and finite element analysis (FEA). The Pro-Xtreme Pistons are designed to be durable, reliable, and capable of handling the extreme stresses and forces generated by high-horsepower and high-rpm engines. Includes: - Pistons - HD Wrist Pins - PVD Rings - Pins - Locks - Spec Sheet

Show More Show Less

Performance Main Bearing Set - S54

affirm Starting At 0% APR - Subject To Eligibility. See Lending Terms

T#:26171616

Part#: 5150-HPMBS-S54

Ships in 3 Business Days

$ 249.99 USD

Add to Wish List

Qty

$ 249.99 USD

Add to Wish List

5150 High-Performance Coated Main Bearing Sets are made for the demands of high-performance engine builds. Treated shells and coated by Calico to reduce friction, these bearings allow your engine to generate more power and resist "spinning" under stress. These coated bearings also have thermal resistant properties that not only perform in high HP applications like forced induction or race use but also help prevent sudden engine failure in the event of oil pressure loss. 5150 bearings have proven themselves on and off the track, lasting longer and outperforming other bearings on the market.

Show More Show Less

BMW M60 / M62 Valve Spring Kit

affirm Starting At 0% APR - Subject To Eligibility. See Lending Terms

T#:37149877

Part#: 5150-HPVSK-M60

Ships in 3 Business Days

$ 1,399.99 USD

Add to Wish List

Qty

$ 1,399.99 USD

Add to Wish List

5150 AutoSport High Performance Main Bearing Set, BMW S55

affirm Starting At 0% APR - Subject To Eligibility. See Lending Terms

T#:23416567

Part#: 5150-HPMBS-S55

Ships in 3 Business Days

$ 549.99 USD

Add to Wish List

Qty

$ 549.99 USD

Add to Wish List

Performance Rod Bearing Kit - S54

affirm Starting At 0% APR - Subject To Eligibility. See Lending Terms
Late Model: S54 Engines after 02/2003 production and later use M10 Bolts.

T#:26171618

Part#: 5150-HPRBK-S54-L

Back Ordered

$ 529.99 USD

Add to Wish List

Qty

$ 529.99 USD

Add to Wish List

Now one of 5150's best sellers has gotten even better! With a 5150 Autosports' complete High-Performance Rod Bearing Kit, you get all the parts you need to easily swap out the factory connecting rod bearing shells and bolts in one simple kit. 5150's S54 bearings are embraced by BMW engine builders worldwide. Popular for both forced induction and N/A builds, their coated bearings are "friction resistant" making thermal breakdowns that can occur due to lack of lubrication a much less common occurrence. Helping to prevent premature engine failures on street cars, and spun bearings under stress at the track when things are most critical. Proven by customers to help you finish the race even with loss of oil pressure! Kit includes: (1) Complete set of ARP S54 Connecting Rod Bolts (1) Complete set of 5150 High Performance Rod Bearing Set (1) ARP Assembly Lubricant packet Tech Notes: As with all bearings, please check your tolerances and size before installation. Due to the specialized tools needed, professional install recommended. There are no returns available on any engine bearings.

Show More Show Less

CP Forged Piston Set BMW M20 B25 Std.

affirm Starting At 0% APR - Subject To Eligibility. See Lending Terms

T#:26205089

Part#: CP-FPS-M20-B25

Back Ordered

$ 1,349.99 USD

Add to Wish List

Qty

$ 1,349.99 USD

Add to Wish List

CP-Carrillo represents the highest quality pistons on the market, engineered for maximum power and durability. Utilizing high-strength, lightweight materials and advanced engineering, this BMW M20B25 piston set features: Lightweight Design: CP-Carrillo pistons are made from high-strength, lightweight materials, such as forged aluminum alloy. Reduced piston weight contributes to improved engine responsiveness and acceleration. Advanced Engineering: CP-Carrillo engineers use state-of-the-art technology and engineering techniques to manufacture pistons that offer optimized combustion, improved fuel efficiency, and increased power output. CP-Carrillo pistons are the best choice for any M20 engine and application, from street bully to all-out track car, and are engineered by one of the most respected names in motorsport to improve performance and reliability. Piston Sets Include: - Pistons - Rings - Pins - Locks - Spec Sheet

Show More Show Less

Xtreme Duty Cylinder Sleeve Set - S58

affirm Starting At 0% APR - Subject To Eligibility. See Lending Terms

T#:22427043

Part#: 5150-CS-S58

Ships in 3 Business Days

$ 1,200.00 USD

Add to Wish List

Qty

$ 1,200.00 USD

Add to Wish List

Introducing 5150 Autosport's Xtreme Duty Cylinder Sleeves. Benefits of Engine Sleeving: Increased Bore Size: Boost power and torque with a larger bore size. Superior Strength: Iron sleeves are perfect for high-power applications, reducing the risk of cylinder wall cracking. Custom Thickness: Prepare your engine for high-performance modifications, including high boost and turbo applications, with thicker cylinder walls. Efficient Heat Dissipation: Improved heat transfer ensures your engine can handle the higher temperatures of high-performance use. Prolonged Engine Life: Reinforced areas and efficient heat transfer reduce the risk of catastrophic failures in high-stress conditions. Compatibility with Upgrades: Ideal for various high-performance modifications like high compression pistons, forced induction, and aggressive cam profiles. Please note that engine block sleeving is a precise process requiring expertise. Consult with our experienced advising team to determine the right components for your goals.

Show More Show Less

Performance Rod Bearing Set - M54

affirm Starting At 0% APR - Subject To Eligibility. See Lending Terms

T#:26171611

Part#: 5150-HPRBS-M54

Ships in 3 Business Days

$ 219.99 USD

Add to Wish List

Qty

$ 219.99 USD

Add to Wish List

5150 High-Performance Coated Rod Bearing Sets are made for the demands of high-performance engine builds. Treated shells and coated by Calico to reduce friction, these bearings allow your engine to generate more power and resist "spinning" under stress. These coated bearings also have thermal resistant properties that not only perform in high HP applications like forced induction or race use but also help prevent sudden engine failure in the event of oil pressure loss. 5150 bearings have proven themselves on and off the track, lasting longer and outperforming other bearings on the market.

Show More Show Less

CP Forged Piston Set - M20B27 - 84.5mm Bore, 8.5:1 CR

affirm Starting At 0% APR - Subject To Eligibility. See Lending Terms

T#:26271772

Part#: CP-FPS-M20-B275

Ships in 3 Business Days

$ 1,396.99 USD

Add to Wish List

Qty

$ 1,396.99 USD

Add to Wish List

CP-Carrillo represents the highest quality pistons on the market, engineered for maximum power and durability. Utilizing high-strength, lightweight materials and advanced engineering, this BMW M20B27 piston set features: Lightweight Design: CP-Carrillo pistons are made from high-strength, lightweight materials, such as forged aluminum alloy. Reduced piston weight contributes to improved engine responsiveness and acceleration. Advanced Engineering: CP-Carrillo engineers use state-of-the-art technology and engineering techniques to manufacture pistons that offer optimized combustion, improved fuel efficiency, and increased power output. CP-Carrillo pistons are the best choice for any M20 engine and application, from street bully to all-out track car, and are engineered by one of the most respected names in motorsport to improve performance and reliability. Piston Sets Include: - Pistons - Rings - Pins - Locks - Spec Sheet

Show More Show Less

Performance Rod Bearing Set - N55

affirm Starting At 0% APR - Subject To Eligibility. See Lending Terms

T#:26238416

Part#: 5150-HPRBS-N55

Ships in 3 Business Days

$ 399.99 USD

Add to Wish List

Qty

$ 399.99 USD

Add to Wish List

5150 High Performance Coated Rod Bearing Sets are made for the demands of high performance engine builds. Treated shells and coated by Calico to reduce friction, these bearings allow your engine to generate more power and resist "spinning" under stress. These coated bearings also have thermal resistant properties that not only perform in high HP applications like forced induction or race use, but also help prevent sudden engine failure in the event of oil pressure loss. 5150 bearings have proven themselves on and off the track, lasting longer and outperforming other bearings on the market.

Show More Show Less

ARP Main Stud Kits - S58

affirm Starting At 0% APR - Subject To Eligibility. See Lending Terms

T#:22427031

Part#: ARP-MSK-S58

Ships in 3 Business Days

$ 229.99 USD

Add to Wish List

Qty

$ 229.99 USD

Add to Wish List

Elevate your BMW S58 engines with the ARP Main Stud Kit, replacing part numbers 11118604584. These studs prevent main cap walk, ensuring stability and protecting the engine from potential damage. They also safeguard the engine block threads, adding an extra layer of protection. Opting for main studs over factory bolts requires engine builders to mic the bores. Studs may require a line hone for proper fitment and alignment, ensuring round and concentric main bearing bores, preventing premature bearing wear, and ensuring optimal oil clearance.

Show More Show Less

BMW N54 3.0L CP-Carrillo Heavy Duty Wrist Pins

affirm Starting At 0% APR - Subject To Eligibility. See Lending Terms

T#:25473980

Part#: CP-PP-HD-N54-6KT

Ships in 3 Business Days

$ 233.99 USD

Add to Wish List

Qty

$ 233.99 USD

Add to Wish List

BMW N54 3.0L CP-Carrillo Heavy Duty Wrist Pins are engineered to enhance the performance and reliability of your BMW's engine. Designed specifically for the N54 3.0L engine, these heavy-duty wrist pins provide superior strength and durability under high-stress conditions. With CP-Carrillo's reputation for high-quality performance parts, these wrist pins ensure your engine operates at its best, delivering exceptional power and longevity.

Superior strength for high-stress conditions
Enhanced engine performance and reliability
Designed specifically for BMW N54 3.0L engines
High-quality construction by CP-Carrillo
Improves engine longevity and durability

Show More Show Less

Performance Rod Bearing Set - M5X

affirm Starting At 0% APR - Subject To Eligibility. See Lending Terms

T#:26171648

Part#: 5150-HPRBS-M50

Ships in 3 Business Days

$ 219.99 USD

Add to Wish List

Qty

$ 219.99 USD

Add to Wish List

5150 High-Performance Coated Rod Bearing Sets are made for the demands of high-performance engine builds. Treated shells and coated by Calico to reduce friction, these bearings allow your engine to generate more power and resist "spinning" under stress. These coated bearings also have thermal resistant properties that not only perform in high HP applications like forced induction or race use, but also help prevent sudden engine failure in the event of oil pressure loss. 5150 bearings have proven themselves on and off the track, lasting longer and outperforming other bearings on the market. Tech Notes: As with all bearings, please check your tolerances and size before installation. Due to the specialized tools needed, professional install recommended.

Show More Show Less

CP-Carrillo Connecting Rod Set - M50 Vanos Pro-Xtreme

affirm Starting At 0% APR - Subject To Eligibility. See Lending Terms

T#:26204923

Part#: CAR-CRS-M50-140-

Ships in 3 Business Days

$ 2,099.99 USD

Add to Wish List

Qty

$ 2,099.99 USD

Add to Wish List

The 5150 AutoSport Pro-Xtreme Connecting Rods, made by CP-Carrillo, are designed to handle extreme horsepower and high RPM applications for BMW M50 VANOS engines with 140 mm Rods. Constructed from high-strength, aircraft-grade steel, these connecting rods are engineered to withstand the forces generated by high-powered engines. The Pro-Xtreme design is specifically tailored to handle up to 2000 horsepower, making these rods suitable for high-performance turbo/drag racing or street/strip applications. They are also designed to handle high engine speeds of up to 9500 RPM, which is necessary for achieving maximum power output. Each connecting rod is precisely fabricated to meet the demands of high-performance engines using advanced manufacturing techniques such as computer-aided design (CAD) and finite element analysis (FEA). The Pro-Xtreme Connecting Rods are designed to be durable, reliable, and capable of handling the extreme stresses and forces generated by high-horsepower and high-rpm engines. Please note that these 140 mm connecting rods are designed to fit M50 VANOS.

Show More Show Less

Ferrea High Performance Oversized Valve Kit - S58

affirm Starting At 0% APR - Subject To Eligibility. See Lending Terms

T#:22427041

Part#: FER-HPVK-S58+

Ships in 3 Business Days

$ 999.99 USD

Add to Wish List

Qty

$ 999.99 USD

Add to Wish List

Elevate the performance of your S58 engine with Ferrea's valve kit. Renowned for their unmatched reliability and durability in extreme conditions. Crafted from aerospace-grade alloys, including the robust EV8-Z18, these valves undergo a meticulous two-step slow forging process to ensure optimal grain flow and minimize material structure damage. Maintaining molecular integrity is paramount, achieved through a rigorous 48-hour heat treatment and stress-relieving process. The valves boast avionics-quality hard chrome and a specially applied hard tip for enhanced performance. Featuring a standard size of 30.1mm for intake and 28.5mm for exhaust, their triple groove design ensures top-notch efficiency. Note that these valves require additional machining due to their overall larger diameter. The kit includes: 12x Intake Valves 12x Exhaust Valves Designed to seamlessly work with factory valve locks, Ferrea's valves are tailored to elevate your BMW S58 engine's performance to new heights.

Show More Show Less

5150 AutoSport Pro-Series Turbo Build Kit - Level 2 (1000 HP) - BMW S...

affirm Starting At 0% APR - Subject To Eligibility. See Lending Terms

T#:23416563

Part#: PRO1000S55

Ships in 4 Business Days

$ 6,299.99 USD

Add to Wish List

Qty

$ 6,299.99 USD

Add to Wish List

An all-encompassing kit packed with forged internals custom-assembled at 5150 Autosport to prepare your BMW S55engine for high horsepower and high boost levels!

CP-Carrillo Connecting Rod Set - S54

affirm Starting At 0% APR - Subject To Eligibility. See Lending Terms
Upgrade Your Connecting Rods in Your High Horsepower S54!

T#:26171622

Part#: CAR-S54-SCR

Ships in 3 Business Days

Starting at $ 2,149.99 USD

Add to Wish List

Starting at $ 2,149.99 USD

Add to Wish List

CP-Carrillo's connecting rods for the BMW S54 engine are specifically engineered to serve as direct replacements for BMW part numbers #11247834437, #11247831924, #11247834310, and 11247831331 in the BMW S54B30, S54B32, S54B33, S54B34, and S54B35 engines, with a length of 139 mm. These Carrillo connecting rods boast a range of impressive features: Crafted from a special chrome-moly based alloy, ensuring strong and durable forged rods. Their lightweight design significantly reduces mass compared to standard rods, optimizing engine performance. These rods have demonstrated exceptional strength and performance in racing environments, vouching for their reliability. Carrillo maintains stringent quality control measures, resulting in tight tolerances and precision balancing for superior performance. Each set is meticulously matched and balanced, ensuring consistent and smooth operation. The connecting rods come equipped with high-quality, non-stretch WMC rod bolts, guaranteeing stability under high-stress conditions. For those seeking even higher performance, there is an option to upgrade to CARR bolts. In conclusion, Carrillo connecting rods stand as the top choice for racers who demand the utmost in performance and reliability from their engines. With a track record of excellence and a suite of advanced features, these rods are the epitome of quality and precision for high-performance applications.

Show More Show Less

Ferrea High Performance Valve Spring Kit - S58

affirm Starting At 0% APR - Subject To Eligibility. See Lending Terms

T#:22427042

Part#: FER-HPVSK-S58

Ships in 3 Business Days

$ 1,099.99 USD

Add to Wish List

Qty

$ 1,099.99 USD

Add to Wish List

Discover the Ferrea Valve Spring Kit for BMW S58 Engines Key Features: Premium Construction: Crafted from premium chrome-silicon steel wire, ensuring precise valve control at high engine speeds. Lightweight Durability: Titanium retainers enhance engine speed and reduce the risk of valve float. Engine-Specific Design: Spring seats are expertly tailored for your specific engine application, providing optimal support for the valve springs. Please note that while this kit is ideal for high-performance racing scenarios, its installation should be handled by experienced professionals to ensure proper operation. Seek expert guidance for a seamless installation and optimal performance.

Show More Show Less

ARP - Connecting Rod Bolt Sets M60/M62

affirm Starting At 0% APR - Subject To Eligibility. See Lending Terms

T#:37149878

Part#: ARP-RBS-M60

Ships in 3 Business Days

$ 269.99 USD

Add to Wish List

Qty

$ 269.99 USD

Add to Wish List

ARP - Connecting Rod Bolt Sets M60/M62 are the ultimate upgrade for BMW enthusiasts seeking to improve engine performance and reliability. Specifically designed for BMW M60 and M62 engines, these high-performance rod bolts provide exceptional strength and durability. Manufactured by ARP, a leader in automotive fastener technology, these bolts are ideal for both street and track applications, ensuring your engine maintains peak performance under extreme conditions.

Key Features:

Superior Strength: Engineered with aerospace-grade materials, these bolts offer unparalleled tensile strength, making them perfect for high-RPM and high-power setups.
Precision Fit: Each bolt is precision-engineered to ensure a perfect fit for BMW M60 and M62 engines, reducing the risk of engine failure.
Enhanced Durability: Designed to withstand intense stress, these bolts improve engine reliability for both daily driving and racing conditions.
Corrosion Resistance: The special coating on these bolts provides excellent resistance to corrosion, extending the life of your engine components.
Easy Installation: With detailed instructions included, these bolts are easy to install, whether by a professional mechanic or a DIY enthusiast.

Turner Motorsport offers the ARP - Connecting Rod Bolt Sets M60/M62, ensuring BMW owners have access to top-quality parts to enhance their engine's performance and reliability.

Show More Show Less

CP-Carrillo Connecting Rod Set M5X Pro-Xtreme

affirm Starting At 0% APR - Subject To Eligibility. See Lending Terms

T#:26204921

Part#: CAR-CRS-S52-XT

Ships in 3 Business Days

$ 2,099.99 USD

Add to Wish List

Qty

$ 2,099.99 USD

Add to Wish List

The 5150 AutoSport Pro-Xtreme Connecting Rods, made by CP-Carrillo, are designed to handle extreme horsepower and high RPM applications for BMW M50 Non-VANOS, M52, S50, S52, and M54 engines with 135 mm Rods. Constructed from high-strength, aircraft-grade steel, these connecting rods are engineered to withstand the forces generated by high-powered engines. The Pro-Xtreme design is specifically tailored to handle up to 2000 horsepower, making these rods suitable for high-performance turbo/drag racing or street/strip applications. They are also designed to handle high engine speeds of up to 9500 RPM, which is necessary for achieving maximum power output. Each connecting rod is precisely fabricated to meet the demands of high-performance engines using advanced manufacturing techniques such as computer-aided design (CAD) and finite element analysis (FEA). The Pro-Xtreme Connecting Rods are designed to be durable, reliable, and capable of handling the extreme stresses and forces generated by high-horsepower and high-rpm engines. Please note that these 135 mm connecting rods are designed to fit M50 Non-VANOS, M52, M52TUB28, S50 U.S, S52 U.S, and M54B30 135mm Rod engines. They will NOT fit M50-VANOS engines, as they require 140 mm Rods.

Show More Show Less

CP Forged Piston Set, BMW M50 Non-VANOS Pro-Xtreme 10:1

affirm Starting At 0% APR - Subject To Eligibility. See Lending Terms

T#:26171659

Part#: FPS-M50NV-10:1

Ships in 3 Business Days

$ 1,399.99 USD

Add to Wish List

Qty

$ 1,399.99 USD

Add to Wish List

The 5150 AutoSport Pro-Xtreme Forged Pistons, made by CP-Carrillo, are designed to handle extreme horsepower and high RPM applications for BMW M50 Non-VANOS engines with 135 mm Rods. Constructed from high-strength, aircraft-grade steel, these pistons are engineered to withstand the forces generated by high-powered engines. The Pro-Xtreme design is specifically tailored to handle up to 2000 horsepower, making these pistons suitable for high-performance turbo/drag racing or street/strip applications. They are also designed to handle high engine speeds of up to 9500 RPM, which is necessary for achieving maximum power output. Each piston is precisely fabricated to meet the demands of high-performance engines using advanced manufacturing techniques such as computer-aided design (CAD) and finite element analysis (FEA). The Pro-Xtreme Pistons are designed to be durable, reliable, and capable of handling the extreme stresses and forces generated by high-horsepower and high-rpm engines. Pro-Xtreme Piston Sets Include: - Pistons - PVD Rings - Pins - Locks - Spec Sheet Please note, that the Pro-Xtreme Piston is engineered to handle up to 2000HP, however, the Standard Wrist Pin can only handle 800-850HP. To exceed 850HP, it is a MUST to use Heavy Duty pins.

Show More Show Less

CP-Carrillo Connecting Rod Set M20 Pro-Xtreme

affirm Starting At 0% APR - Subject To Eligibility. See Lending Terms
For Vehicles With 135mm Connecting Rods

T#:26205099

Part#: CAR-CRS-M20-XT

Ships in 3 Business Days

$ 2,099.99 USD

Add to Wish List

Qty

$ 2,099.99 USD

Add to Wish List

The 5150 AutoSport Pro-Xtreme Connecting Rods, made by CP-Carrillo, are designed to handle extreme horsepower and high RPM applications for BMW M20 engines with 135 mm Rods. Constructed from high-strength, aircraft-grade steel, these connecting rods are engineered to withstand the forces generated by high-powered engines. The Pro-Xtreme design is specifically tailored to handle up to 2000 horsepower, making these rods suitable for high-performance turbo/drag racing or street/strip applications. They are also designed to handle high engine speeds of up to 9500 RPM, which is necessary for achieving maximum power output. Each connecting rod is precisely fabricated to meet the demands of high-performance engines using advanced manufacturing techniques such as computer-aided design (CAD) and finite element analysis (FEA). The Pro-Xtreme Connecting Rods are designed to be durable, reliable, and capable of handling the extreme stresses and forces generated by high-horsepower and high-rpm engines. Please note that these 135 mm connecting rods are designed to fit M20 135mm Rod engines. They will NOT fit 130 mm Rod Engines.

Show More Show Less

Athena Cut Ring Head Gasket S14

affirm Starting At 0% APR - Subject To Eligibility. See Lending Terms

T#:28537477

Part#: ATH-HG-CR-S14-95

Ships in 3 Business Days

$ 284.99 USD

Add to Wish List

Qty

$ 284.99 USD

Add to Wish List

This Athena Cut Ring Head Gasket is specifically engineered to replace BMW part 11121316714 for the S14B20, S14B23, S14B25, S14B27 engines found in the E30 M3. Factory OEM & MLS head gaskets are only engineered to handle a limited amount of cylinder pressures before they start to leak, causing a range of issues, including engine overheating, loss of power, misfires, and in severe cases, catastrophic engine failure. Athena-SCE Cut Ring Head Gaskets are uniquely designed to handle increased cylinder pressure caused by power modifications, making them the recommended choice for applications making 16+ psi. Design: Athena-SCE's gasket body is composed of Motorgasket, a reinforced material developed by Athena's R&D department. This consists of a steel core covered with two layers of asbestos-free aramid fibre and offers excellent thermal and mechanical resistance without compromising its ability to adapt to mating surfaces. To ensure maximum sealing under all conditions, a silicone bead is also applied to critical sealing areas, such as oil and coolant passages. The AISI 304 stainless steel cooper rings bite into the aluminum head, providing maximum sealing around the cylinder bore and optimizing engine performance, even on engines with nitrous and/or turbo applications that exceed 2 bar boost.

Show More Show Less

5150 AutoSport High Performance Rod Bearing Set - N54

affirm Starting At 0% APR - Subject To Eligibility. See Lending Terms

T#:38419052

Part#: 5151-HPRBS-S54

Ships in 3 Business Days

$ 399.99 USD

Add to Wish List

Qty

$ 399.99 USD

Add to Wish List

Upgrade your BMW S54 engine with the 5150 AutoSport High Performance Rod Bearing Set—a premium solution designed to improve durability, reliability, and longevity. This high-performance bearing set addresses the well-known rod bearing wear issues found in the E46 M3, Z3M, and Z4M engines, offering superior materials and precision engineering for high-RPM and high-load applications. Product Features: Advanced Materials – Manufactured from tri-metal or bi-metal alloys, these bearings provide superior wear resistance and strength under extreme conditions. Optimized Oil Clearance – Precision tolerances ensure proper oil flow and lubrication for maximum engine performance. Proven Durability – Built for motorsport, high-performance street use, and endurance applications, ensuring long-lasting reliability. OEM Replacement – Designed to fit factory specifications for an easy, direct installation with no modifications needed. Prevention of Bearing Failure – Helps mitigate the risk of premature rod bearing failure, a common issue in the S54 engine. For optimal performance, we recommend pairing these bearings with ARP rod bolts and an upgraded oil pump to further enhance engine protection and longevity.

Show More Show Less

5150 AutoSport & Cat Cams Camshaft Set - 278* / 272* - 11.20mm / 10.3...

affirm Starting At 0% APR - Subject To Eligibility. See Lending Terms

T#:39126861

Part#: N55CCCAM-278-272

Ships in 3 Business Days

$ 1,799.99 USD

Add to Wish List

Qty

$ 1,799.99 USD

Add to Wish List

Cat Cams offer great performance at a reasonable price. Cat Cam offers cams in the most popular enthusiast upgrade specs to ensure there is an option for whatever your power goal is. This N55 camshaft set is designed to bring your engine to the next level! Whether it's for street or track purposes, this camshaft set offers the power gains and throttle response needed to push your N55 to its limits. These camshafts are a direct fit for seamless installation and with some simple tuning can produces great power while retaining factory-like idle and driveability. Valvetronic and Dual VANOS functionality can be fully retained, or with an aftermarket throttle body, the valvetronic system can be locked open, providing even more control.

Show More Show Less

BMW N55/S55 Valves By Super Tech

affirm Starting At 0% APR - Subject To Eligibility. See Lending Terms

T#:39329323

Part#: SUP-HPVK-S55-32/

Ships in 3 Business Days

$ 1,143.99 USD

Add to Wish List

Qty

$ 1,143.99 USD

Add to Wish List

SP Connecting Rod Set, BMW M60 / M62

affirm Starting At 0% APR - Subject To Eligibility. See Lending Terms

T#:37149883

Part#: SP-CRS-M60

Ships in 3 Business Days

$ 1,599.99 USD

Add to Wish List

Qty

$ 1,599.99 USD

Add to Wish List

Connecting rods for the BMW M60B30, M60B40, M62B35, M62B44, and M62B46 engines with a 143 mm length

SuperTech High Performance Oversized Valve Kit - S58

affirm Starting At 0% APR - Subject To Eligibility. See Lending Terms

T#:22427039

Part#: SUP-HPVK-S58+

Ships in 3 Business Days

$ 1,099.99 USD

Add to Wish List

Qty

$ 1,099.99 USD

Add to Wish List

Elevate the performance of your S58 engine with Supertech's oversized valve kit, celebrated for its unmatched reliability and durability even in the most trying conditions. Boasting a size of 31.1mm for intake and 29.5mm for exhaust, their triple groove design ensures unparalleled efficiency. It's worth noting that these valves, being larger in diameter, necessitate additional machining. Included in this kit: 12x Intake Valves 12x Exhaust Valves

Show More Show Less

SuperTech High Performance Valve Kit - S58

affirm Starting At 0% APR - Subject To Eligibility. See Lending Terms

T#:22427038

Part#: SUP-HPVK-S58

Ships in 3 Business Days

$ 1,099.99 USD

Add to Wish List

Qty

$ 1,099.99 USD

Add to Wish List

SuperTech High Performance Valve Spring Kit 84 Lbs - S58

affirm Starting At 0% APR - Subject To Eligibility. See Lending Terms

T#:22427033

Part#: SUP-HPVSK-S58-84

Ships in 3 Business Days

$ 999.99 USD

Add to Wish List

Qty

$ 999.99 USD

Add to Wish List

Upgrade your BMW S58 with Supertech's specialized valve spring kits, designed for enhanced control and reliability. Engineered for high-performance demands, these kits are favored by enthusiasts, engine builders, and race teams alike. Crafted from premium materials, the springs offer superior rates, improved valve control, and enhanced durability compared to stock alternatives. Tailored to specific BMW engine configurations, Supertech kits ensure proper valve operation, preventing float and maximizing power output without compromising reliability.

Show More Show Less

SuperTech High Performance Valve Spring Kit 75lbs - S58

affirm Starting At 0% APR - Subject To Eligibility. See Lending Terms

T#:22427032

Part#: SUP-HPVSK-S58-75

Ships in 3 Business Days

$ 999.99 USD

Add to Wish List

Qty

$ 999.99 USD

Add to Wish List

Upgrade your BMW S58 with Supertech's specialized valve spring kits, designed for enhanced control and reliability. Engineered for high-performance demands, these kits are favored by enthusiasts, engine builders, and race teams alike. Crafted from premium materials, the springs offer superior rates, improved valve control, and enhanced durability compared to stock alternatives. Tailored to specific BMW engine configurations, Supertech kits ensure proper valve operation, preventing float and maximizing power output without compromising reliability.

Show More Show Less

Ferrea High Performance Valve Kit - S58

affirm Starting At 0% APR - Subject To Eligibility. See Lending Terms

T#:22427040

Part#: FER-HPVK-S58

Ships in 3 Business Days

$ 999.99 USD

Add to Wish List

Qty

$ 999.99 USD

Add to Wish List

Xtreme Duty Cylinder Sleeve Set - BMW S85

affirm Starting At 0% APR - Subject To Eligibility. See Lending Terms

T#:34181274

Part#: 5150-CS-S85

Ships in 3 Business Days

$ 1,999.99 USD

Add to Wish List

Qty

$ 1,999.99 USD

Add to Wish List

Xtreme Duty Cylinder Sleeve Set - BMW S65

affirm Starting At 0% APR - Subject To Eligibility. See Lending Terms

T#:34181271

Part#: 5150-CS-S65

Ships in 3 Business Days

$ 1,599.99 USD

Add to Wish List

Qty

$ 1,599.99 USD

Add to Wish List

ARP Head Stud Kit BMW S55 Custom Age 625+

affirm Starting At 0% APR - Subject To Eligibility. See Lending Terms
N55 Engines it is a MUST to drill and tap!

T#:41458801

Part#: ARP-HSK-S55-CA

Back Ordered

$ 899.99 USD

Add to Wish List

Qty

$ 899.99 USD

Add to Wish List

Upgrade your S55 with the ARP Head Stud Kit BMW S55 Custom Age 625+ and drive with confidence under pressure.

CP-Carrillo Connecting Rod Set - S54 Pro-Xtreme

affirm Starting At 0% APR - Subject To Eligibility. See Lending Terms

T#:26204927

Part#: CAR-CRS-S54-XT

Back Ordered

$ 2,299.99 USD

Add to Wish List

Qty

$ 2,299.99 USD

Add to Wish List

The 5150 AutoSport Pro-Xtreme Connecting Rods, made by CP-Carrillo, are designed to handle extreme horsepower and high RPM applications for BMW S54 engines with 139 mm Rods. Constructed from high-strength, aircraft-grade steel, these connecting rods are engineered to withstand the forces generated by high-powered engines. The Pro-Xtreme design is specifically tailored to handle up to 2000 horsepower, making these rods suitable for high-performance turbo/drag racing or street/strip applications. They are also designed to handle high engine speeds of up to 9500 RPM, which is necessary for achieving maximum power output. Each connecting rod is precisely fabricated to meet the demands of high-performance engines using advanced manufacturing techniques such as computer-aided design (CAD) and finite element analysis (FEA). The Pro-Xtreme Connecting Rods are designed to be durable, reliable, and capable of handling the extreme stresses and forces generated by high-horsepower and high-rpm engines.

Show More Show Less

CP-Carrillo Forged Piston Set - M54B28 Std. Size

affirm Starting At 0% APR - Subject To Eligibility. See Lending Terms
For Vehicles With M54B25 Engine Only

T#:26071892

Part#: M54B25-CPP-84

Back Ordered

Starting at $ 2,206.98 USD

Add to Wish List

Starting at $ 2,206.98 USD

Add to Wish List

CP-Carrillo sets the benchmark for premium aftermarket forged pistons. Crafted with high-strength, lightweight materials and cutting-edge engineering, this BMW M54B25 piston set boasts the following features: Lightweight Design: Constructed from forged aluminum alloy, CP-Carrillo pistons offer reduced weight, enhancing engine responsiveness and acceleration for a dynamic driving experience. Advanced Engineering: Leveraging state-of-the-art technology, CP-Carrillo engineers optimize combustion, fuel efficiency, and power output, ensuring peak performance in every application. Wide Configuration Range: With a variety of bore sizes and compression ratios available, CP-Carrillo provides options to tailor pistons to specific engine builds and performance objectives. Quality Construction: Each CP-Carrillo piston undergoes precision machining and rigorous testing to meet exacting standards, guaranteeing consistent quality and performance in every set. Engineered by one of motorsport's most respected names, CP-Carrillo pistons are the ultimate choice for the M54B25 engine, whether for street performance or track dominance. Piston Sets Include: Pistons Rings Pins Locks Spec Sheet Optional Extras: Skirt Coating - Adding a Protective Layer Between the Sides of the Piston and Cylinder Walls Dome Coating - Adding a Protective Layer to the Top of The Piston HD-Wrist Pins - A Must if You are Planning on Going Beyond 850 HP! X Forging - Reducing Rotational Mass By Moving the Wristpin Inwards and Shortening it While Increasing Overall Strength Please Note: It is essential to have all engine modifications performed by a qualified professional to ensure proper installation and optimal engine performance, safety, and reliability.

Show More Show Less

Project Cars

SELECT YOUR BMW

5150 Autosport BMW Internal Engine Parts

Sub-Categories

Key Features:

Select Vehicle

Category

Brand

Price

Shipping

Narrow Results