BMW Engine Parts

OEM Bremi Ignition Coil - M62 M73 M52 M54 S52 S62

T#:340638

Part#: 12131703228

In Stock

$ 48.36

This product was last offered at the strikethrough price on
04-27-2026

$ 36.99 USD

Add to Wish List

Qty

$ 36.99 USD

Add to Wish List

Bremi is one of the most trusted names in ignition coils among BMW enthusiasts. We trust these in our vehicles. Replace yours and get your BMW running right today!

Bremi Ignition Coil - E30 E36 E34 E32 E38 E31

T#:340701

Part#: 12139066468

Ships in 1 Business Day

$ 65.99

This product was last offered at the strikethrough price on
04-09-2026

$ 55.99 USD

Add to Wish List

Qty

$ 55.99 USD

Add to Wish List

Ignition coils are key to the efficiency and performance of your BMW. With a faulty coil the spark plug is not burning the air/fuel mixture properly and that can lead to problems anywhere in the engine and exhaust (including catalytic converters and O2 sensors). Problems with one or more coils will cause a fault code but not always a check engine light. A misfire code may be related to an ignition coil but could be from other things as well. Sometimes a visual inspection of a coil and coil boot will give an indication of a failure. You can also move coils around to different cylinder banks to see if the misfire code follows a suspect coil. We suggest always having one or two coils on hand to keep as spares.

This Bremi coil was used in M42, M50, M50tu, and M60 engines. BMW has made numerous changes to ignition coil part numbers in recent years but has approved this part number to work in the vehicles listed below. This part number replaces previous BMW part numbers 12131703359, 12131731884, 12131730765, 12131748394, 12131729842, 12131726178, 12131726177, 12131727108, 12131734468, and 12131748395.

Sold per coil. Does not includes connecting boot. If in need of connecting boots please purchase part number 12139067831

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts. All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

This item fits the following BMWs:
1990-1991 E30 BMW 318i 318is 318ic
1991-1995 E36 BMW 325i 325i 325ic M3
1991-1995 E34 BMW 525i 530i 540i
1992-1994 E38 BMW 740i 740il
1995 E38 BMW 740i 740il
1991-1996 E31 BMW 840i 840ci

Show More Show Less

Bremi Ignition Coil

T#:340576

Part#: 12131712219

In Stock at Vendor

$ 28.78

This product was last offered at the strikethrough price on
04-09-2026

$ 25.43 USD

Add to Wish List

Qty

$ 25.43 USD

Add to Wish List

Get your engine back to peak performance with a new ignition coil.

OEM Bremi Ignition Coil - E60 M5, E63 M6

T#:402843

Part#: 12137841556

In Stock

$ 107.59

This product was last offered at the strikethrough price on
06-10-2026

$ 91.99 USD

Limited Qty Sale

Add to Wish List

Qty

$ 107.59

This product was last offered at the strikethrough price on
06-10-2026

$ 91.99 USD

Limited Qty Sale

Add to Wish List

Ignition coils are key to the efficiency and performance of your BMW. With a faulty coil the spark plug is not burning the air/fuel mixture properly and that can lead to problems anywhere in the engine and exhaust (including catalytic converters and O2 sensors). Problems with one or more coils will cause a fault code but not always a check engine light. A misfire code may be related to an ignition coil but could be from other things as well. Sometimes a visual inspection of a coil and coil boot will give an indication of a failure. You can also move coils around to different cylinder banks to see if the misfire code follows a suspect coil. We suggest always having one or two coils on hand to keep as spares.

This item fits the following BMWs:
2006-2010 E60 BMW M5
2006-2010 E63 BMW M6

Show More Show Less

Bremi Ignition Wire Set - E30, E34

T#:361156

Part#: 12121720529

In Stock

$ 181.99 USD

Add to Wish List

Qty

$ 181.99 USD

Add to Wish List

Includes ignition coil wire and conduit

Ignition Coil With Spark Plug Connector

T#:597425

Part#: 12138611236

Ships in 1 Business Day

$ 58.99

This product was last offered at the strikethrough price on
04-10-2026

$ 50.99 USD

Add to Wish List

Qty

$ 50.99 USD

Add to Wish List

Mishimoto Oil Line Fitting Adapter Kit - E46 Z4 E9X

T#:380389

Part#: MMOCF-BMW

In Stock

$ 88.99 USD

Add to Wish List

Qty

$ 88.99 USD

Add to Wish List

Install a custom oil cooler on your street or track BMW with help from the Mishimoto Oil Line Fitting Kit! This kit has 100% CNC-machined components, including the 6061 aluminum oil line fittings and the 303 stainless steel tie-down plate. This adapter kit is applicable for BMW E36 (Euro oil-housing equipped), E46, and E90 vehicles, and allows for the use of -10AN fittings to route oil to a custom oil cooler setup. This is an ideal upgrade for drivers seeking additional cooling for track environments or for those who would like additional engine bay space for an oil accumulator or supercharger setup. Included in this kit are two stock BMW O-rings for leak-free installation. Features: Allows for use of -10AN fittings for custom oil cooler setup 100% CNC-machined components, including 6061 aluminum fittings and 303 stainless steel tie-down plate Includes durable stock BMW O-rings for leak-free installation Provides additional engine bay space for applications with an oil accumulator or supercharger setup Included as part of the Mishimoto BMW E46 M3 Oil Cooler Kit Mishimoto Lifetime Warranty Included: (1) Stainless Steel Fitting Clamp (2) -10AN Fittings (2) BMW Oil O-rings (1) M8 x 1.25 x 25mm Button-Head Bolt Mishimoto Lifetime Warranty WARNING! Prop 65 may apply to this product. Proposition 65 (Safe Drinking Water and Toxic Enforcement Act of 1968) is a California law that applies to call companies selling products in California. Prop 65 requires any listed chemical present above very low levels that are known to cause cancer, birth defects, or other reproductive harm. For more information about California Prop 65 warning see: www.P65Warnings.ca.gov.

Show More Show Less

Mishimoto Baffled Oil Catch Can - F8X M2 M3 M4 S55

T#:637363

Part#: MMBCC-F80-15CBE

In Stock

$ 306.99 USD

Add to Wish List

Qty

$ 306.99 USD

Add to Wish List

Give your 2015–2020 BMW M3/M4 the protection it deserves with the Mishimoto Baffled Oil Catch Can Kit. The introduction of the S55 into the M3 and M4 in 2015 was the first time compact M’s saw turbos from the factory, but these engines brought along another long-standing tradition—blow-by. The Mishimoto BMW M3/M4 catch can kit uses proven engineering from the patent pending Mishimoto 2-Port Compact Baffled Oil Catch Can, with its 50-micron bronze filter and internal baffle, to better separate the oil from the crankcase vapors. The engineers at Mishimoto designed a CNC-machined lid that features large inlet and outlet ports to match the inner dimension of the CCV hose. This baffled oil catch can defends your intercooler, intake system, and VANOS system from oil blow-by and helps maintain proper octane levels to reduce potential detonation. The kit comes with two direct-fit hoses, which require no modification to the engine cover, and one direct-fit billet aluminum mounting bracket that is extremely easy to install and mounts the can in a serviceable location! Two aluminum, 3/4” barb fittings connect the hoses to the can. And, like every Mishimoto oil catch can, this baffled catch can kit comes with the Mishimoto Lifetime Warranty! Our catch cans are different from most air-oil-separator (AOS) systems on a few levels. First, our catch cans are not heated. This means that all of the blow-by is able to condense in the can, including low-octane oil vapors and contaminated fuel vapors. Most AOS systems also drain the blow-by back into the oil pan, while our catch cans trap the blow-by and keep it out of the engine permanently. If you’ve seen what we’ve seen in the bottom of our catch cans, you won’t want that draining back into your oil either. *After installation, Mishimoto recommends checking the contents of the baffled catch cans every 1,000 miles until a baseline is established. Oil blow-by accumulation will vary with ambient temperatures and driving conditions. It is important that the contents of the can do not rise above the internal baffle* Features: Direct fit for the 2015–2020 F8X BMW M3 and M4 Single can mounts in line with the CCV system to separate oil from air using a 50-micron bronze filter Helps reduce carbon buildup on intake valves Patent-pending billet 6061 aluminum can sealed with Viton™ O-rings Installs in under 30 minutes Robust CNC-machined anodized aluminum bracket mounts the can in a serviceable location Includes pre-molded hoses for simplified installation Defends Vanos system and essential engine components from oil blow-by CNC-machined aluminum barbed fittings ensure a sturdy connection between lines and can Catch can has a 3 oz. capacity for longer servicing intervals Internal air diverter increases air turbulence to improve oil separation Helps maintain proper octane levels to reduce potential detonation Filter and can are fully serviceable Mishimoto Lifetime Warranty Included: (1) Compact Baffled Oil Catch Can (1) Application-Specific Mounting Bracket (2) Direct-Fit Hoses (2) 3/4" Aluminum Barbed Fittings (4) Worm Gear Clamps Mounting Hardware Mishimoto Lifetime Warranty WARNING! Prop 65 may apply to this product. Proposition 65 (Safe Drinking Water and Toxic Enforcement Act of 1968) is a California law that applies to call companies selling products in California. Prop 65 requires any listed chemical present above very low levels that are known to cause cancer, birth defects, or other reproductive harm. For more information about California Prop 65 warning see: www.P65Warnings.ca.gov.

Show More Show Less

Large Aluminum Oil Catch Can

T#:597051

Part#: MMOCCLA

In Stock

$ 127.99 USD

Add to Wish List

Qty

$ 127.99 USD

Add to Wish List

WARNING! Prop 65 may apply to this product. Proposition 65 (Safe Drinking Water and Toxic Enforcement Act of 1968) is a California law that applies to call companies selling products in California. Prop 65 requires any listed chemical present above very low levels that are known to cause cancer, birth defects, or other reproductive harm. For more information about California Prop 65 warning see: www.P65Warnings.ca.gov.

Show More Show Less

Bremi Ignition Rotor - E23, E24, E28, E30, E32, E34, E38

T#:384317

Part#: 12111715906

Ships in 1-2 days

$ 59.99 USD

Add to Wish List

Qty

$ 59.99 USD

Add to Wish List

Cure your misfire problems

Mishimoto Universal Catch Can Kit - Carbon Fiber

T#:372557

Part#: MMOCCCF

In Stock

$ 162.99 USD

Add to Wish List

Qty

$ 162.99 USD

Add to Wish List

Universal kit with a catch can and rubber hose; for retrofitting on a variety of vehicles. Carbon fiber catch can prevents a harmful buildup of oil inside of the turbocharger, intake manifold, intercooler and piping. Separates oil particles from PCV/CCV air Defends intercooler, intake system, and essential components from oil blow-by Made from lightweight carbon fiber Compact design makes for easy engine bay placement Checking fluid levels made easy with built in sight tube Comes complete with mounting bracket, hose, all necessary clamps, fittings, and mounting hardware Mishimoto Lifetime Warranty WARNING! Prop 65 may apply to this product. Proposition 65 (Safe Drinking Water and Toxic Enforcement Act of 1968) is a California law that applies to call companies selling products in California. Prop 65 requires any listed chemical present above very low levels that are known to cause cancer, birth defects, or other reproductive harm. For more information about California Prop 65 warning see: www.P65Warnings.ca.gov.

Show More Show Less

Camshaft Position Sensor - Intake

T#:34683819

Part#: 12147539165

In Stock at Vendor

$ 49.99

This product was last offered at the strikethrough price on
05-07-2026

$ 44.99 USD

Add to Wish List

Qty

$ 44.99 USD

Add to Wish List

Bremi Camshaft Position Sensor - Intake is an essential component for optimizing your BMW’s engine timing and performance. Manufactured by Bremi and available through Turner Motorsport, this high-quality intake camshaft position sensor precisely monitors the camshaft’s rotation and communicates critical data to the engine control unit. By ensuring accurate timing for the intake valves, this sensor helps maintain optimal fuel efficiency, smooth idling, and reduces emissions. Replacing a faulty camshaft position sensor can prevent common engine issues such as misfires, stalling, or rough idling.

The Bremi Camshaft Position Sensor - Intake meets OEM specifications, providing a reliable, durable solution that’s designed to withstand high temperatures and vibration for long-lasting performance.

Benefits:

Improves Engine Timing: Provides precise timing data for smooth, responsive engine performance Enhances Fuel Efficiency: Optimizes fuel use, saving on fuel costs and reducing environmental impact Reduces Emissions: Helps maintain cleaner combustion and lowers vehicle emissions Prevents Engine Issues: Minimizes risk of misfires, rough idling, and stalling, prolonging engine life Easy to Install: Direct fit for BMW models, making replacement quick and hassle-free Bremi Camshaft Position Sensor - Intake is the perfect choice to maintain your BMW’s high performance and reliability.

Show More Show Less

Mishimoto Performance Direct-Fit Oil Cooler - F8X M2 M3 M4 S55 ...

T#:637357

Part#: MMOC-F80-15

In Stock

$ 609.99

This product was last offered at the strikethrough price on
05-08-2026

$ 549.99 USD

Add to Wish List

Qty

$ 549.99 USD

Add to Wish List

Add some much-needed durability and cooling power to your M3 or M4 with the Mishimoto 2015-2020 BMW M3/M4 Oil Cooler. True to form, the engineers at BMW designed the M3/M4’s oil cooler with efficient use of space in mind. Suspended perpendicular from the rest of the cooling stack, this location utilizes the Bimmer’s aerodynamics in order to cool the oil, all while putting the lightweight, tube-and-fin cooler in harm's way of road hazards. We here at Mishimoto made sure to beef up the oil cooler design for the F80/82 with our performance oil cooler. We ditched the lightweight design for a full aluminum, TIG-welded bar-and-plate cooler for added strength and cooling. The bars and plates are a much more robust form of heat exchanger core construction intended for improved heat transfer and have the strength to shrug off potential road debris, keeping your oil temps down, and where it should be. We also added 10mm to the core’s thickness, equating in a 46% increase in core volume, and increased the oil capacity by .4 qt. The Mishimoto 2015-2020 BMW M3/M4 Oil Cooler fits directly in place of the stock unit, and includes the Mishimoto Lifetime Warranty for a simplified and worry-free installation. Features: Direct fit for the 2015–2020 BMW F8X M3, M4, and M2 Competition Full aluminum TIG-welded construction 46% increase in core volume Increases oil capacity by .44 quarts Robust bar-and-plate construction for improved durability and heat rejection Silver powder-coated finish for maximum protection No cutting or modifications required Mishimoto Lifetime Warranty Included: (1) Performance Oil Cooler (2) Replacement O-Rings Mounting Hardware Mishimoto Lifetime Warranty WARNING! Prop 65 may apply to this product. Proposition 65 (Safe Drinking Water and Toxic Enforcement Act of 1968) is a California law that applies to call companies selling products in California. Prop 65 requires any listed chemical present above very low levels that are known to cause cancer, birth defects, or other reproductive harm. For more information about California Prop 65 warning see: www.P65Warnings.ca.gov.

Show More Show Less

Camshaft Position Sensor

T#:598679

Part#: 12141740959

In Stock at Vendor

$ 66.99

This product was last offered at the strikethrough price on
05-07-2026

$ 64.99 USD

Add to Wish List

Qty

$ 64.99 USD

Add to Wish List

Bremi Ignition Wire Set - E23, E24, E28

T#:379842

Part#: 12121705718

In Stock

$ 135.99 USD

Add to Wish List

Qty

$ 135.99 USD

Add to Wish List

Original equipment replacement wire set

Bremi Ignition Wire Set - E24, E28

T#:371076

Part#: 12121307171

In Stock at Vendor

$ 412.73 USD

Add to Wish List

Qty

$ 412.73 USD

Add to Wish List

Includes ignition coil wire and conduit

Mishimoto 19 Row Universal Oil Cooler

T#:378414

Part#: MMOCUL

In Stock at Vendor

$ 536.99 USD

Add to Wish List

Qty

$ 536.99 USD

Add to Wish List

Even under optimum driving conditions increased oil temperatures will cause a drop in pressure and will decrease the ability for your engine to be properly lubricated. With this new oil cooler, you can keep your oil temperatures down for optimum driving conditions. The kit includes four-feet of stainless braided line, adapter fittings, and oil filter sandwich adapter. Rows: 19 Overall Dimensions: 13" x 5.5" x 2" Core Dimensions: 11.25" x 5.5" x 2" Braided Hoses: 4ft .75 inch & 4ft 9 inch Braided Hose Fittings: -10AN Sandwich Plate Fittings: -10AN WARNING! Prop 65 may apply to this product. Proposition 65 (Safe Drinking Water and Toxic Enforcement Act of 1968) is a California law that applies to call companies selling products in California. Prop 65 requires any listed chemical present above very low levels that are known to cause cancer, birth defects, or other reproductive harm. For more information about California Prop 65 warning see: www.P65Warnings.ca.gov.

Show More Show Less

Bremi Ignition Wires - E10

T#:591857

Part#: 12121360842

Ships in 1-2 days

$ 58.99 USD

Add to Wish List

Qty

$ 58.99 USD

Add to Wish List

Complete set of ignition wires

N54 Mishimoto Baffled Oil Catch Can

T#:383384

Part#: MMBCCN5406CBE

In Stock

$ 253.99 USD

Add to Wish List

Qty

$ 253.99 USD

Add to Wish List

Oil venting and circulation continues to be a problem on BMW engines and now even more so on the turbocharged N54 and N55 engines. The existing stock system does a very poor job of separating fluid and vapor and this leads to an oily film or even small pools of oil throughout the turbos and intake. We're seeing a lot more 135 and 335 cars with drivability and performance issues because oil has sneaked by the ring seals and is coating the intake piping, intercooler, intake valves, and other critical areas. The problem is worsened with higher boost levels. Oil is excellent for lubricating moving parts but terrible when it gets into the combustion chamber, effectively lowering the octane rating and reducing performance. Our own shop has gone the extra step and offers media and chemical blasting of the intake valves to strip away the oily buildup we have seen. Our shop also strongly recommends an oil catch can be installed in the line for the crankcase vent. The oil catch can traps oil as it leaves the valve cover and holds it in a canister. This catch can is located on the cooler side of the engine where the oil will condense easier and stay in the can. Whatever minimal vapors are left over in the oil is then vented back through the canister and into the intake where it is safe to be burned up in the engine or recirculated back through the system again. This is the way the system was designed! At each oil change simply unscrew the canister and empty the trapped oil with your regular used oil. Installing one of these will avoid costly repairs in the future and help maintain your boost and performance. It's one of the smartest modifications you can make because it demonstrates a well-thought out tuning strategy and care for the condition of your engine. The Mishimoto Oil Catch Can is made from aluminum and with a stealthy black anodized finish. It installs on the cooler side of the engine with a dedicated bracket and new oversized vent lines. The location is key as heat will evaporate the oil and send too much vapor back into the engine (where cooler air will turn it back into fluid). Note: Since the crankcase vent system is considered part of the overall emissions system, installing this may be a violation of local, state, and federal laws. While exemptions are made for track/race and off-road use, check with your local state inspection facility on using this in street-driven vehicles. This item fits the following BMWs with the N54 twin-turbo engine: 2008-2010 E82 E88 BMW 135i 2007-2010 E9X BMW 335i 335xi 2006-2010 E60 BMW 535i 535xi WARNING! Prop 65 may apply to this product. Proposition 65 (Safe Drinking Water and Toxic Enforcement Act of 1968) is a California law that applies to call companies selling products in California. Prop 65 requires any listed chemical present above very low levels that are known to cause cancer, birth defects, or other reproductive harm. For more information about California Prop 65 warning see: www.P65Warnings.ca.gov.

Show More Show Less

MINI R50 to R53 Magnetic Engine Oil Drain Plug M14X1.5

T#:31125648

Part#: MMODP1415B

In Stock

$ 22.99 USD

Add to Wish List

Qty

$ 22.99 USD

Add to Wish List

BMW Two Port Universal Catch Can - Black

T#:23020165

Part#: MMBCC-CBTWO

In Stock

$ 160.99 USD

Add to Wish List

Qty

$ 160.99 USD

Add to Wish List

Optimize your vehicle's performance and shield crucial components with the Mishimoto Compact 2-Port Baffled Oil Catch Can. This innovative solution effectively separates oil particles from PCV/CCV air using a 50-micron bronze filter, ensuring defense against oil blow-by for your intercooler, intake system, and vital parts. Constructed with a patented billet 6061 aluminum can sealed with Viton™ O-Rings, this catch can guarantees both durability and effectiveness.

Equipped with a universal mounting bracket, it allows adaptable installation and comes complete with two CNC-machined aluminum 1/2" barbed hose fittings. With an enhanced 3 oz internal capacity, service intervals are prolonged, while its fully serviceable filter and can ensure enduring functionality.

Engineered for safety in pressurized applications, the internal air diverter enhances oil separation by amplifying air turbulence. Available in black, red, or polished finishes, this catch can preserves proper octane levels, reducing potential detonation and promoting extended engine life.

The product package includes the Compact 2-Port Baffled Oil Catch Can, two Aluminum 1/2" Barbed Fittings, and a Universal Mounting Bracket, all backed by the Mishimoto Lifetime Warranty.

WARNING! Prop 65 may apply to this product.

Proposition 65 (Safe Drinking Water and Toxic Enforcement Act of 1968) is a California law that applies to all companies selling products in California.

Prop 65 mandates listing any chemical present above very low levels that are known to cause cancer, birth defects, or other reproductive harm.

For more information about California Prop 65 warning, visit: www.P65Warnings.ca.gov.

Show More Show Less

MINI R55 to R61 Magnetic Engine Oil Drain Plug M16X1.5

T#:31092530

Part#: MMODP1615B

In Stock

$ 22.99 USD

Add to Wish List

Qty

$ 22.99 USD

Add to Wish List

MINI R55 to R61 Magnetic Engine Oil Drain Plug M16X1.5 removes abrasive metal particles from drivetrain fluid to ensure longevity. The magnet attracts and holds minute abrasive and ferrous metal particles, preventing their circulation through lubrication systems. Metal particles can appear in lubricating or hydraulic systems due to normal wear, machining residues, sub-surface casting flaws, and stress usage. Mishimoto Drain Plugs help prevent excessive wear to internal components by holding these particles.

Enhanced Engine Protection: Removes metal particles to reduce wear
Magnetic Attraction: Holds abrasive and ferrous particles securely
Improved Lubrication: Prevents circulation of harmful particles
Durable Construction: Built to last and withstand harsh conditions
Easy Installation: Simple to replace with standard drain plug

Safety Note: This product may be subject to Proposition 65, a California law requiring warnings for products containing chemicals known to cause cancer, birth defects, or other reproductive harm. For more information, visit www.P65Warnings.ca.gov.

Show More Show Less

Mishimoto Universal 10 Row Oil Cooler

T#:378421

Part#: MMOCU

In Stock at Vendor

$ 410.99 USD

Add to Wish List

Qty

$ 410.99 USD

Add to Wish List

This universal oil cooler from Mishimoto is far superior to the factory unit with its 11" x 2.76" x 1.97" core. Even under optimum driving conditions increased oil temperatures will cause a drop in pressure and will decrease the ability for your engine to be properly lubricated. With this new oil cooler, you can keep your oil temperatures down for optimum driving conditions. The kit includes 4 feet of stainless braided line, adapter fittings, and oil filter sandwich adapter. Mishimoto Automotive is a leading manufacturer of aftermarket performance cooling products. The company was established back in 2003 with one goal. That goal was to provide customers with quality cooling system upgrades that work on the track and on the road. At Mishimoto, you never have to worry about the quality of the product you are installing. This kit is universal and is not a direct bolt on. *For custom applications only. Not a direct bolt on. WARNING! Prop 65 may apply to this product. Proposition 65 (Safe Drinking Water and Toxic Enforcement Act of 1968) is a California law that applies to call companies selling products in California. Prop 65 requires any listed chemical present above very low levels that are known to cause cancer, birth defects, or other reproductive harm. For more information about California Prop 65 warning see: www.P65Warnings.ca.gov.

Show More Show Less

Bremi Distributor Cap - E30 M3

T#:14355

Part#: 12111312160

In Stock

$ 132.89

This product was last offered at the strikethrough price on
01-22-2026

$ 115.99 USD

Limited Qty Sale

Add to Wish List

Qty

$ 132.89

This product was last offered at the strikethrough price on
01-22-2026

$ 115.99 USD

Limited Qty Sale

Add to Wish List

This is a Bremi brand distributor cap for E30 M3 with S14 engine. Bremi is an OEM supplier to BMW of ignition components. This part number is an direct replacement for Bosch #03241.We recommend getting the corresponding Bremi distributor rotor # 12111312157 at the same time.

This item fits the following BMWs:
1988-1991 E30 BMW M3

Show More Show Less

Bremi Crankshaft Sensor - 13627806782

T#:27871806

Part#: 13627806782

In Stock at Vendor

$ 71.99

This product was last offered at the strikethrough price on
05-07-2026

$ 63.99 USD

Add to Wish List

Qty

$ 63.99 USD

Add to Wish List

The crankshaft position sensor tells the computer whether the timing is correct in the engine. Symptoms such as no start or extended cranking times can be a telltale sign that you need to replace your crankshaft positioning sensor that is either faulty or damaged.

Show More Show Less

Mishimoto Performance Air-to-Water Intercooler Power Pack - F8X M2 M3...

CARB certified for sale in all 50 states

T#:637354

Part#: MMB-F80-PP

EO#: D-759-13

In Stock at Vendor

$ 2,652.99 USD

Add to Wish List

Qty

$ 2,652.99 USD

Add to Wish List

BMW has a knack for maintaining its stake as the benchmark when it comes to performance luxury vehicles, with the F8X generation being no exception. The S55 that powers the 2015–2020 BMW F8X M3, M4, and M2 Competition is dripping with technology, which includes an air-to-water intercooling system as a means of keeping cool. Where BMW’s intercooling system design was enough to help bring this generation of mid-sized M’s to their peak, we here at Mishimoto found some weaknesses that we felt obliged to address, with a power bundle consisting of our full Performance Intercooler Product suite. The Mishimoto 2015–2020 BMW F8X M3/M4 Performance Intercooler Power Pack counters the weaknesses in BMW’s design, starting with the charge pipes. Cracking under pressure or splitting at the seams are common problems with factory plastic charge pipes. These can result in less than ideal situations as you pilot your M3 or M4. We created a brand-new design for the charge pipes that inspire more confidence in handling the boost pressure. Our design features a full aluminum construction with a cast midsection designed specifically to squeeze past the intake. Our charge pipe kit also includes a pair of matte black silicone couplers for a sleek and secure connection to the intercooler. The nondescript silver box is out, and the stylish new Mishimoto Performance Air-to-Water Intercooler is in. With a new look, our design fits perfectly in the M3 and M4’s engine bay, both in terms of installation and aesthetics. The beauty is more than just skin deep. Our improved core design features a bar-and-plate core with a 29% increase in core volume, as well as a unique single-pass coolant flow layout for optimal heat transfer. Combined with our 16% increase in flow through the core, we were able to record a 12°F temperature drop in intake air temperatures while testing our full Power Pack. An air-to-water intercooling system wouldn’t be complete without the heat exchanger. When it came to BMW’s design, it was a solid foundation, but we still saw room to grow, literally. Our full aluminum design added 6” to the height of the core, equating in a 180% increase in external fin surface area and a 60% increase in core volume. With our heat exchanger in the S55’s system, we recorded a 10°F drop in global intercooler coolant temperatures and an average gain of 11 whp and 8 wtq when the full Mishimoto 2015–2020 BMW F8X Performance Intercooler Power Pack was tested on our Stage 1 tuned M3. For added security, we made sure to include our optional steel mesh stone guard with the Mishimoto Performance Heat exchanger to keep all the tubes and fins intact. We also utilized a variable fin pitch on our heat exchanger’s core for optimal cooling on DCT-equipped vehicles. Even though the F8X generation of the M3, M4, and M2 Competition was designed to pull ahead of the rest, there's still much to be desired when it comes to cooling. The Mishimoto 2015–2020 BMW F8X M3/M4 Performance Intercooler Power Pack is the perfect companion for your build, and like all of our products, is covered under the Mishimoto Lifetime Warranty. Features: Direct fit for the BMW F8X M3, M4, and M2 Competition Includes S55 Performance Intercooler, Heat Exchanger, and Charge Pipe Kit 12°F drop in intake air temperatures and 10°F reduction in global intercooler coolant temperatures Dyno-proven average power gains of 11 whp and 8 wtq with peak gains of up to 31 whp and 10 wtq on stage 1 tuned vehicle The intercooler features a unique bar-and-plate, single-pass coolant passage design, and cast aluminum end tanks for optimal flow and cooling capacity Intercooler core volume increased by 29% with 16% improved flow Heat Exchanger features all-aluminum construction with 180% increase in fin surface area and 60% increase in core volume Heat exchanger includes an optional stone guard for added protection against road debris Heat Exchanger utilizes variable fin pitch for improved flow to DCT cooler Charge Pipe Kit features full aluminum construction and cast midsection for maximum durability and perfect fitment Charge pipes include matte silicone couplers for sleek and secure connection to the intercooler Mishimoto Lifetime Warranty Includes: (1) Performance Air-to-Water Intercooler (1) Performance Heat Exchanger (1) Heat Exchanger Stone Guard (2) Charge Pipes (2) Silicone Couplers (4) Worm Gear Clamps Mounting Hardware Mishimoto Lifetime Warranty WARNING! Prop 65 may apply to this product. Proposition 65 (Safe Drinking Water and Toxic Enforcement Act of 1968) is a California law that applies to call companies selling products in California. Prop 65 requires any listed chemical present above very low levels that are known to cause cancer, birth defects, or other reproductive harm. For more information about California Prop 65 warning see: www.P65Warnings.ca.gov.

Show More Show Less

N20/N26 Mishimoto Baffled Oil Catch Can

T#:389788

Part#: MMBCCN20N2612CB

In Stock at Vendor

$ 278.95 USD

Add to Wish List

Qty

$ 278.95 USD

Add to Wish List

il venting and circulation continues to be a problem on BMW engines and the N20 engine is not immune from this. The existing stock system does a poor job of separating fluid and vapor and this leads to an oily film or even small pools of oil throughout the turbos and intake. Performance issues are caused by oil sneaking by the ring seals and is coating the intake piping, intercooler, intake valves, and other critical areas. The problem is worsened with higher boost levels. Oil is excellent for lubricating moving parts but terrible when it gets into the combustion chamber, effectively lowering the octane rating and reducing performance. Our own shop has gone the extra step and offers media and chemical blasting of the intake valves to strip away the oily buildup we have seen. Our shop also strongly recommends an oil catch can be installed in the line for the crankcase vent. The oil catch can traps oil as it leaves the valve cover and holds it in a canister. This catch can is located on the cooler side of the engine where the oil will condense easier and stay in the can. Whatever minimal vapors are left over in the oil is then vented back through the canister and into the intake where it is safe to be burned up in the engine or recirculated back through the system again. This is the way the system was designed! At each oil change simply unscrew the canister and empty the trapped oil with your regular used oil. Installing one of these will avoid costly repairs in the future and help maintain your boost and performance. It's one of the smartest modifications you can make because it demonstrates a well-thought out tuning strategy and care for the condition of your engine. The Mishimoto Oil Catch Can is made from aluminum and with a stealthy black anodized finish. It installs on the cooler side of the engine with a dedicated bracket and new oversized vent lines. The location is key as heat will evaporate the oil and send too much vapor back into the engine (where cooler air will turn it back into fluid). Note: Since the crankcase vent system is considered part of the overall emissions system, installing this may be a violation of local, state, and federal laws. While exemptions are made for track/race and off-road use, check with your local state inspection facility on using this in street-driven vehicles. This item fits the following BMWs with the N20 or N26 turbo engine: 2014-2016 F2X 228i 228i xDrive 2012-2016 F3X 320i 320i xDrive 328i 328i xDrive 428i 428i xDrive WARNING! Prop 65 may apply to this product. Proposition 65 (Safe Drinking Water and Toxic Enforcement Act of 1968) is a California law that applies to call companies selling products in California. Prop 65 requires any listed chemical present above very low levels that are known to cause cancer, birth defects, or other reproductive harm. For more information about California Prop 65 warning see: www.P65Warnings.ca.gov.

Show More Show Less

Crankshaft Position Sensor

T#:2027109

Part#: 13627639278

Ships in 1 Business Day

$ 45.99

This product was last offered at the strikethrough price on
05-07-2026

$ 44.99 USD

Add to Wish List

Qty

$ 44.99 USD

Add to Wish List

Camshaft Sensor

T#:590416

Part#: 12141485845

In Stock at Vendor

$ 45.98

This product was last offered at the strikethrough price on
07-15-2026

$ 42.04 USD

Add to Wish List

Qty

$ 42.04 USD

Add to Wish List

Mishimoto Performance Engine Oil Cooler - F10/90 M5, F06/12/13 M6, G1...

T#:6258386

Part#: MMOC-F10-12SL

In Stock at Vendor

$ 887.99 USD

Add to Wish List

Qty

$ 887.99 USD

Add to Wish List

The BMW M5 power and handling statistics are completely mind-blowing for a car tipping the scales at well over two tons. The S63 twin-turbo V8 is underrated from the factory and responds well to tuning and bolt on modifications. Calling it the ultimate super sedan would not do this car justice, it’s just that good. But every amazing automobile must have an Achilles’ heel, right? Some investigation into this model told us that enthusiasts were seeing elevated oil temperatures during track driving conditions. Our team set out to create a replacement, high-performance oil cooler that could handle the rigors of extreme driving conditions and the abuse of daily commuting. The Mishimoto S63 M5/M6 oil cooler features extremely precise CNC-machined billet-aluminum end tanks which are professionally TIG-welded to our robust bar-and-plate core. Our strategically designed 55mm-thick core provides a massive 24% increase in core volume, and a 40% increase in external fin surface area. This added surface area promotes greater heat transfer, which directly impacts internal fluid temperatures. Our performance oil cooler is a complete bolt-on solution that includes everything needed for an easy installation such as hardware and replacement O-rings for the oil lines. Our heat exchanger is finished in a durable silver powder coat, providing both corrosion resistance and improved aesthetics. Whether your M5 sees frequent track time or just the occasional back-road jaunt, upgrading the oil cooler is a great way to extend the life of your S63 and ensure maximum engine output when you need it most. As with all our BMW products, this oil cooler includes our signature Mishimoto Lifetime Warranty. Direct fit for 2012+ BMW M5/M6 models CNC-machined billet aluminum end tanks provide improved durability over stock stamped tanks Robust bar-and-plate core resists damage from road debris and provides optimal cooling efficiency 24% increase in core volume over stock for improved cooling capacity 40% increase in external fin area provides improved heat transfer during extreme driving conditions Precision CNC-machined inlet and outlet prevent leaks Includes new OEM-quality oil line O-rings for easy installation Durable silver powder coated finish prevents corrosion Mishimoto Lifetime Warranty Purchase Includes: (1) Performance Oil Cooler (4) Mounting Bracket Grommets (2) Oil Line Connection M8 X 1.25 Bolts (2) Oil Line O-rings Mishimoto Lifetime Warranty WARNING! Prop 65 may apply to this product. Proposition 65 (Safe Drinking Water and Toxic Enforcement Act of 1968) is a California law that applies to call companies selling products in California. Prop 65 requires any listed chemical present above very low levels that are known to cause cancer, birth defects, or other reproductive harm. For more information about California Prop 65 warning see: www.P65Warnings.ca.gov. The Mishimoto S63 M5/M6 oil cooler features extremely precise CNC-machined billet-aluminum end tanks which are professionally TIG-welded to our robust bar-and-plate core. Our strategically designed 55mm-thick core provides a massive 24% increase in core volume, and a 40% increase in external fin surface area. This added surface area promotes greater heat transfer, which directly impacts internal fluid temperatures. Our performance oil cooler is a complete bolt-on solution that includes everything needed for an easy installation such as hardware and replacement O-rings for the oil lines. Our heat exchanger is finished in a durable silver powder coat, providing both corrosion resistance and improved aesthetics. Whether your M5 sees frequent track time or just the occasional back-road jaunt, upgrading the oil cooler is a great way to extend the life of your S63 and ensure maximum engine output when you need it most. As with all our BMW products, this oil cooler includes our signature Mishimoto Lifetime Warranty. Direct fit for 2012+ BMW M5/M6 models CNC-machined billet aluminum end tanks provide improved durability over stock stamped tanks Robust bar-and-plate core resists damage from road debris and provides optimal cooling efficiency 24% increase in core volume over stock for improved cooling capacity 40% increase in external fin area provides improved heat transfer during extreme driving conditions Precision CNC-machined inlet and outlet prevent leaks Includes new OEM-quality oil line O-rings for easy installation Durable silver powder coated finish prevents corrosion Mishimoto Lifetime Warranty Purchase Includes: (1) Performance Oil Cooler (4) Mounting Bracket Grommets (2) Oil Line Connection M8 X 1.25 Bolts (2) Oil Line O-rings Mishimoto Lifetime Warranty

Show More Show Less

Mishimoto Performance Oil Cooler - E60 M5, E63/64 M6 S85 5.0L ...

T#:5282875

Part#: MMOC-E60-06

In Stock at Vendor

$ 714.99 USD

Add to Wish List

Qty

$ 714.99 USD

Add to Wish List

After over a decade of use, some of the E60 M5 & E63/64 M6 components have begun to show their age. The factory engine oil cooler is a common leak point on the E60, typically from failed O-rings or cracked weld points. In addition, the location of the front-mounted cooler increases the chance of damage from road debris and general clogging of external fins, resulting in reduced cooling efficiency. That, combined with the high-strung engine and hefty chassis, means oil temperatures tend to rise during aggressive driving. That's why Mishimoto's engineering team set out to remedy both issues with this performance oil cooler. Drawing on their vast experience with BMWs and the latest in engineering tools, Mishimoto's team was able to create a direct-fit replacement oil cooler with substantial improvements in both durability and cooling efficiency. The Mishimoto Performance Oil Cooler features a robust bar-and-plate core, which provides improved durability and aids in heat rejection. The core utilizes a strategic fin design which provides a 41% increase in external fin surface area and a 30% increase in internal fin surface area to help draw heat out of the oil and dissipate it into the air. This oil cooler features CNC-machined inlet/outlet ports and includes new OEM O-rings for a seamless and leak-free installation. This cooler is finished in a silver powder coat, ensuring long-term durability and corrosion resistance. And, as with all BMW performance products, this oil cooler includes the signature Mishimoto Lifetime Warranty. Fits 2006-2010 BMW E60 M5 / E63 M6 / E64 M6* (*Requires minor trimming of plastic OEM oil cooler shrouding) Replaces failure-prone factory oil cooler and provides improved cooling performance 40.3% increase in core volume for efficient cooling Robust bar-and-plate core provides improved pressure tolerance and durability 41% increase in external fin surface area for improved heat transfer 30% increase in internal fin surface area draws heat out of oil quickly and efficiently CNC-machined inlet/outlet mates perfectly with stock oil cooler lines Includes OEM oil line O-rings Durable silver powder coated finish provides optimal corrosion resistance Patent Pending Mishimoto Lifetime Warranty Included: Mishimoto Performance Oil Cooler Oil Line O-rings Mishimoto Lifetime Warranty WARNING! Prop 65 may apply to this product. Proposition 65 (Safe Drinking Water and Toxic Enforcement Act of 1968) is a California law that applies to call companies selling products in California. Prop 65 requires any listed chemical present above very low levels that are known to cause cancer, birth defects, or other reproductive harm. For more information about California Prop 65 warning see: www.P65Warnings.ca.gov.

Show More Show Less

Mishimoto Direct-Fit Oil Cooler Kit - E46 M3

T#:363342

Part#: MMOCE4601

In Stock at Vendor

$ 1,032.99 USD

Add to Wish List

Qty

$ 1,032.99 USD

Add to Wish List

The S54 is an incredible feat of engineering. Smooth power delivery, individual throttle bodies, and an 8,000 rpm redline make for an unforgettable driving experience. As with any BMW, maintaining optimal oil temperatures is key to extending the life of your vehicle and ensuring that you're getting an unparalleled driving experience. As many of these vehicles see frequent track time, the team at Mishimoto decided to develop a performance oil cooler kit that would provide improved durability and deliver the power needed for track driving. The result: an extremely efficient core with a proven 30°F (16.7°C) drop in oil temperature. With an increase in core thickness of 110%, this oil cooler kit raises your oil capacity by 0.44 qt. The oil cooler end tanks, cast from a single piece of aluminum and TIG-welded to the core, have been designed for maximum reliability, giving you the confidence you need to push your E46 M3 to the limits.

Show More Show Less

BMW 335I/335XI/135I Baffled Oil Catch Can

T#:599444

Part#: MMBCC-N55-11CBE

In Stock at Vendor

9% off MSRP $ 300.00

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 272.99 USD

Add to Wish List

Qty

9% off MSRP

$ 300.00

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 272.99 USD

Add to Wish List

BMW 335I/335XI/135I Direct Fit Catch Can, 2011-2013 Direct fit for 2011-2013 BMW 335I/335XI/135I Single 2-Port Compact Baffled Oil Catch Can separates oil particles using 50-micron bronze filter Application-specific bracket mounts the can in a serviceable location Billet 6061 aluminum sealed can Defends intercooler, intake system, and VANOS system from oil blow-by Helps maintain proper octane levels to reduce potential detonation Internal air diverter increases air turbulence to improve oil separation Filters and can are fully serviceable Mishimoto Lifetime Warranty The Mishimoto BMW N55 Baffled Oil Catch Can is designed and engineered to reduce carbon build-up, a common issue with the direct fuel injection N55 engines. The Mishimoto BMW N55 catch can kit uses proven engineering from the Mishimoto 2-Port Compact Baffled Oil Catch Can, with its bronze filter and internal baffle, to better separate the oil from the crankcase vapors. WARNING! Prop 65 may apply to this product. Proposition 65 (Safe Drinking Water and Toxic Enforcement Act of 1968) is a California law that applies to call companies selling products in California. Prop 65 requires any listed chemical present above very low levels that are known to cause cancer, birth defects, or other reproductive harm. For more information about California Prop 65 warning see: www.P65Warnings.ca.gov.

Show More Show Less

Performance Oil Cooler - BMW G8X M3 M4

T#:15544955

Part#: MMOC-G80-21SL

In Stock at Vendor

$ 776.99 USD

Add to Wish List

Qty

$ 776.99 USD

Add to Wish List

Keep your 2021+ BMW M3/M4 cool and collected with the Mishimoto 2021+ BMW M3/M4 performance oil cooler. Much like their predecessors, the G8X M3 and M4 were designed with efficiency in mind. This can be a double-edged sword, as the optimally arranged engine bay has components placed in precarious positions. Most notably, the oil cooler is placed on the undercarriage, parallel to the road's surface. This placement increases air flow and uses aerodynamics to pull air through the core, but it also makes the stock cooler vulnerable to scrapes, bumps, and other road hazards. With this in mind, the engineers at Mishimoto set out to design a robust G8X oil cooler to keep your M3 or M4 running cool on and off the track. We started by swapping the stock tube-and-fin cooler for a bar-and-plate with CNC-machined end tanks. Our cooler boasts a 35.7-percent thicker core and a 41-percent increase in core volume for superior cooling efficiency. Our cooler fits directly in place of the stock unit and retains the stock seals and bash guards for optimal airflow and additional protection. The Mishimoto performance oil cooler for the 2021+ BMW G8X M3/M4 includes everything needed for installation and, as with all Mishimoto products, it's protected by the Mishimoto Lifetime Warranty for a lifetime of protection and cooling. Product Features: Direct fit for the 2021+ BMW G8X M3/M4 Full aluminum TIG-welded construction 41-percent increase in core volume and 35.7-percent thicker core than stock for improved cooling efficiency Robust bar-and-plate core provides superior pressure tolerance and durability Retains stock seals for optimal air flow from fresh air ducts Retains bash guards to protect cooler from bumps and curbs Silver powder coated finish for maximum corrosion resistance No cutting or modifications required Includes everything needed for installation Mishimoto Lifetime Warranty

Show More Show Less

Mishimoto Nylon Braided Oil Cooler Hose Kit

T#:2839826

Part#: MMSBH-F80-15

In Stock at Vendor

$ 456.99 USD

Add to Wish List

Qty

$ 456.99 USD

Add to Wish List

The F8X M3/4 are equipped with a set of hardlines connecting the oil pump tot he oil cooler, these corrode overtime and start to fail causing oil leaks leading and improper oiling of your engine. This Mishimoto kit includes both lines and all needed brackets and hardware for a OE like installation, Features Direct replacement for OE hard lines -10AN fittings and adapters for use with OE oil cooler Mishimoto Lifetime Warranty WARNING! Prop 65 may apply to this product. Proposition 65 (Safe Drinking Water and Toxic Enforcement Act of 1968) is a California law that applies to call companies selling products in California. Prop 65 requires any listed chemical present above very low levels that are known to cause cancer, birth defects, or other reproductive harm. For more information about California Prop 65 warning see: www.P65Warnings.ca.gov.

Show More Show Less

Hitachi Voltage Regulator - BMW E31 E32 E34 E36

T#:48850064

Part#: 12311747920

Ships in 6 Business Days

$ 37.99 USD

Add to Wish List

Qty

$ 37.99 USD

Add to Wish List

This voltage regulator is a crucial component that controls the alternator's output, preventing overcharging by adjusting the current to maintain a safe range of vehicle voltage, thereby protecting the battery and electrical system. Symptoms of failure include dim lights, battery warnings, or a dead battery, often requiring replacement, which can be internal or external to the alternator.

Show More Show Less

Mass Air Flow Sensor

T#:47644906

Part#: 13627593624

In Stock at Vendor

$ 193.99

This product was last offered at the strikethrough price on
05-07-2026

$ 173.99 USD

Add to Wish List

Qty

$ 173.99 USD

Add to Wish List

T#:2925

Part#: 12139067831

In Stock

$ 10.99

This product was last offered at the strikethrough price on
04-03-2026

$ 7.13 USD

Add to Wish List

Qty

$ 7.13 USD

Add to Wish List

Sometimes a bad coil may just be a broken or damaged connector boot. This is especially true on cars with a leaking valve cover gasket where the oil has contamintated the rubber boot and the electrical parts inside. This boot can be replaced on its own without having to buy a whole new coil. This part is also useful if you purchased a coil that did not come with a new boot.

This boot works with the 12131748018 ignition coil only and fits the vehicles listed below.

Sold per boot/per coil.

This item fits the following BMWs:
1996-1998 E36 BMW 323is 323ic 328i 328is 328ic M3
1999-2000 E46 BMW 323i 323ci 328i 328ci
2001-2002 E46 BMW 325i 325ci 325xi 330i 330ci 330xi
1997-2003 E39 BMW 528i 540i M5
2001-2002 E39 BMW 525i 530i
1996-2001 E38 BMW 740i 740il 750il
1996-1999 E31 BMW 840ci 850ci
2000-2003 E53 BMW X5 4.4i X5 4.6is
2000-2002 E53 BMW X5 3.0i
1997-2002 Z3 BMW Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i
1998-2000 Z3 BMW Z3 M Roadster Z3 M Coupe
2000-2003 E52 BMW Z8

Show More Show Less