BMW Fuel System Parts

The High Pressure Fuel Pump (HPFP) is a point of weakness in many BMW engines and fuel systems. If this goes it will prevent your car from running or starting due to fuel starvation. Restore your fuel system's operation with high quality OE BMW fuel pump from Bremmen Parts.

Bremmen Parts High-Pressure Pump This item fits the following BMW Chassis: E70 X5M,E71 X6M,E70 X5,E71 X6,F01,F02,F10,F12,F13

Fits BMW Engines including: N63,N63N,S63

The O ring that is located on the engine side of the injector. Best to replace whenever removing the fuel injectors for any reason.
If you drive a European vehicle, chances are high your vehicle came equipped with one or more Victor Reinz gaskets. Choose OE quality VR gaskets and seals and do the job right the first time.

Measurements: 9.2x2.8

If you drive a European vehicle, chances are high your vehicle came equipped with one or more Elring gaskets. Choose OE quality gaskets and seals and do the job right the first time.

We are proud to bring out this truly awesome product that makes getting the required Flex Fuel hardware on your BMW with incredible ease and minimal effort, in your own driveway.

Our kit is entirely plug-and-play with the factory vehicle harness. No cutting or splicing of OEM wiring/connectors. It installs in minutes and can be removed without a trace on the car!

Our team used SolidWorks to design a Flow Optimized Flex Fuel Sensor Adapter (FFSA) to ensure fuel flow is unobstructed and with no added pressure drop at full fuel pump flow from the fuel tank to your motor when our kit is installed. This is important when pushing the factory fuel system with all the power Ethanol can provide over petrol!

Flex fuel sensor housing is designed to neatly install into the factory BMW fuel hat location.

Flex Fuel Sensor Adapter also contains two 1/8 NPT ports that allow installation of an auxiliary Fuel Pressure sensor for vehicles that don’t come with an OEM one from the factory for future use. Depending on fitment, either port can be used.

Install the bootmod3 Flex Fuel Plug and Play Kit and flash your flex fuel enabled bootmod3 OTS MultiMap or Custom Map in minutes and you’re off to the races never worrying about alcohol/petrol blend % in your fuel tank. It does not get better or easier than this!

bootmod3 FlexFuel Plug and Play Kit:

Minutes to install at home as opposed to hours at a shop with car up on lift fabricating/cutting into factory fuel lines and splicing/cutting/pinning into OEM electrical

4+ hours in time/cost savings to get going on Flex Fuel as compared to most other kits that require making custom fuel lines, fittings, and custom wiring! 

Fully reversible/removable and back to stock without a trace in minutes

Custom 3-piece Aluminum-6061 Flex Fuel sensor adapter with built-in sensor bypass to allow for obstruction-free fuel flow made to fit in the vehicle factory fuel hat area below the rear seat

All connecting points are sealed with fuel-safe Viton O-rings

Flex Fuel Sensor Adapter housing provides additional 1/8 NPT ports for optional Fuel Pressure sensor addition to vehicles without a factory one for bootmod3 CustomROM v2 support

CANBUS Enabled Ethanol Content Analyzer (ECA) that integrates with bootmod3 CustomROM for complete and seamless conversion of your BMW to FlexFuel for bootmod3 Flex Fuel enabled OTS MultiMaps and custom tunes with your bootmod3 tuner of choice

Power/CANBus 4-wire plug-and-play harness

100% Fully Plug and Play harness to the BMW Fuel Controller connectors (EKP3) on S55, N55 vehicles

100% Fully Plug and Play harness on the BMW Body Domain Controller (BDC/FEM) connector on Gen1 F-series B48/B58

Continental Flex Fuel sensor 3-wire harness

Custom Aluminum-6061 CANBus Enclosure for the bootmod3 ECA board

Custom, kink-free teflon braided line allowing plug-and-play installation with the OEM fuel hat and factory 5/16” or 3/8” fuel feed line. No cutting or new lines required.

-6 AN fitting by Racetronix

This fuel-sending unit is crucial for accurate fuel level readings in your instrument cluster. When it malfunctions, you risk running out of fuel unknowingly. Replace it with this reliable part from URO to avoid such issues.

Key Features:

Guaranteed to fit your vehicle Direct OE replacement design restores factory function Simple plug-and-play connection to original wiring Constructed with high-quality materials for durability against heat and fuel corrosion Alloy conductors reduce electrical resistance, ensuring precise fuel level readings Designed and tested for long-lasting reliability