BMW Engine Parts

Ignition coils are key to the efficiency and performance of your BMW. With a faulty coil the spark plug is not burning the air/fuel mixture properly and that can lead to problems anywhere in the engine and exhaust (including catalytic converters and O2 sensors). Problems with one or more coils will cause a fault code but not always a check engine light. A misfire code may be related to an ignition coil but could be from other things as well. Sometimes a visual inspection of a coil and coil boot will give an indication of a failure. You can also move coils around to different cylinder banks to see if the misfire code follows a suspect coil. We suggest always having one or two coils on hand to keep as spares.

This Bremi coil was used in M42, M50, M50tu, and M60 engines. BMW has made numerous changes to ignition coil part numbers in recent years but has approved this part number to work in the vehicles listed below. This part number replaces previous BMW part numbers 12131703359, 12131731884, 12131730765, 12131748394, 12131729842, 12131726178, 12131726177, 12131727108, 12131734468, and 12131748395.

Sold per coil. Does not includes connecting boot. If in need of connecting boots please purchase part number 12139067831

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

This item fits the following BMWs:
1990-1991 E30 BMW 318i 318is 318ic
1991-1995 E36 BMW 325i 325i 325ic M3
1991-1995 E34 BMW 525i 530i 540i
1992-1994 E38 BMW 740i 740il
1995 E38 BMW 740i 740il
1991-1996 E31 BMW 840i 840ci

Bremi Camshaft Position Sensor - Intake is an essential component for optimizing your BMW’s engine timing and performance. Manufactured by Bremi and available through Turner Motorsport, this high-quality intake camshaft position sensor precisely monitors the camshaft’s rotation and communicates critical data to the engine control unit. By ensuring accurate timing for the intake valves, this sensor helps maintain optimal fuel efficiency, smooth idling, and reduces emissions. Replacing a faulty camshaft position sensor can prevent common engine issues such as misfires, stalling, or rough idling.

The Bremi Camshaft Position Sensor - Intake meets OEM specifications, providing a reliable, durable solution that’s designed to withstand high temperatures and vibration for long-lasting performance.

Benefits:

Improves Engine Timing: Provides precise timing data for smooth, responsive engine performance Enhances Fuel Efficiency: Optimizes fuel use, saving on fuel costs and reducing environmental impact Reduces Emissions: Helps maintain cleaner combustion and lowers vehicle emissions Prevents Engine Issues: Minimizes risk of misfires, rough idling, and stalling, prolonging engine life Easy to Install: Direct fit for BMW models, making replacement quick and hassle-free Bremi Camshaft Position Sensor - Intake is the perfect choice to maintain your BMW’s high performance and reliability.

Rogue Engineering has developed a power pulley kit that reduces the drag on specific pulleys while allowing others to remain at their same efficiency. This allows for perfect operation in daily driven vehicles without a hiccup or stutter. However, when the demand for power is requested, the power pulley kit allows for the freed power to become apparent.  The term "power" pulley is a bit of a misnomer. Underdrive pulleys actually free up power by reducing the drag caused by the accessories.  These pulleys are based off a calculated percentage from factory dimensions, so that particular component speeds are safely reduced without affecting their true purpose.

Rogue Engineering Power Pullies are CNC machined from 6061-T6, heat treated aluminum and specially coated with a MIL-A-8625 Type III hard coat anodize finish. This kind of anodizing is not to be confused with a Type II cosmetic anodize finish (typical colors such as red, blue, silver, green, etc.). The hard coat anodize finish actually builds a small surface layer on top of the aluminum, preventing wear.

Fits the following BMWs:
2000-2006 E46 BMW 323/325/328/330

Rogue Engineering has developed a power pulley kit that reduces the drag on specific pulleys while allowing others to remain at their same efficiency. This allows for perfect operation in daily driven vehicles without a hiccup or stutter. However, when the demand for power is requested, the power pulley kit allows for the freed power to become apparent.  The term "power" pulley is a bit of a misnomer. Underdrive pulleys actually free up power by reducing the drag caused by the accessories.  These pulleys are based off a calculated percentage from factory dimensions, so that particular component speeds are safely reduced without affecting their true purpose.

Rogue Engineering Power Pullies are CNC machined from 6061-T6, heat treated aluminum and specially coated with a MIL-A-8625 Type III hard coat anodize finish. This kind of anodizing is not to be confused with a Type II cosmetic anodize finish (typical colors such as red, blue, silver, green, etc.). The hard coat anodize finish actually builds a small surface layer on top of the aluminum, preventing wear.

This part fits the following BMW engines:
S54

This part fits the following chassis:
E46, Z3, Z4

Ferrea valve springs are developed from high strength alloys, including premium grade chrome silicone steel These springs are manufactured with state-of-the-art equipment. Ferrea springs are heat-treated and stress-relieved, which dramatically increases the spring's life. Strict quality control procedures and cycle testing ensures consistency from batch to batch. Ferrea valve springs provide the stability needed for high lift, high rpm racing and street car engines. Kit includes a set of 24 springs. MUST be used with the Ferrea Spring Seat and Titanium Retainers. See links below. 

https://www.turnermotorsport.com/e/p-163-e36-325-328-m3-ferrea-spring-seat-set/ 

https://www.turnermotorsport.com/e/p-31-e36-325-328-m3-ferrea-titanium-retainer-set/

This item fits the following BMWs:
1992-1998 E36 BMW 323is 323ic 325i 325is 325ic 328i 328is 328ic M3
1991-1995 E34 BMW 525i