BMW Engine Parts

The Crankshaft Position Sensor measures the speed and position of the crankshaft to determine the proper fuel and timing requirement for the best performance.

When doing any sort of repair or maintenance there is no replacement for genuine factory parts. Turner Motorsport carries the Genuine BMW brand with pride and has the parts you need to complete your next project with confidence.

Genuine BMW Pulse Generator
This item fits the following BMW Chassis:
E36 M3,E36

Fits BMW Engines including:
M50,S50

Elevate your BMW maintenance with this comprehensive tool kit designed for valve and valve stem seal removal and replacement, all without the need to remove the head. This time-saving kit ensures efficiency and ease in the process, making it an essential for DIY enthusiasts and professionals alike. The universal fitment and a range of adapters guarantee versatility across various brands and motors, providing maximum utility.

• Removes and replaces valves and valve stem seals without head removal
• Time and effort-saving solution
• Wide range of adapters for versatile use
• Universal fitment for compatibility with different brands and motors
• Essential for DIY and professional use

Contents:

• 1 - Lever Bar
• 4 - Valve Spring Compressor Adapters
• 1 - Slotted/Notched Pulling Device
• 1 - Hook Pulling Device
• 1 - Connector for Valve Spring Adapters
• 1 – Connector for Pulling Device
• 1 - Extension for Valve Spring Adapters

The VANOS system on your N51, N52, and N54 engine controls the valve timing inside the engine. The system is hydraulically operated based on instructions from the engine computer. It's very complex and BMW has not yet perfected the system. The VAN0S solenoid is the actuator that takes instruction from the ECU and activates the VANOS unit on the front of the engine. When the solenoid is failing (or failed) you can end up with a rough running engine, misfires, bad fuel economy, lack of power, and more. It should trigger multiple fault codes and a check engine light for misfires, camshaft control, VAN0S solenoid, boost pressure control, and maybe others. It's important to thoroughly troubleshoot fault codes but VAN0S solenoids are a known issue with these engines.

The VANOS solenoids are located on the front of the engine and may be replaced without removing many other components. In some cases, you may be able to remove the suspect one, clean it, reinstall, and reset your fault codes. If your fault codes come back it's a strong indication that a replacement is required. Or you can buy the new solenoid and replace instead of doing the work twice.

VANOS solenoid for the intake and exhaust are the same part number. Order 2 if you want to replace them both.

When doing any sort of repair or maintenance there is no replacement for genuine factory parts. Turner Motorsport carries the Genuine BMW brand with pride and has the parts you need to complete your next project with confidence.

We recommend replacing the solenoid sealing gaskets as well when replacing the solenoid. You can find these under T#363393

This item fits the following BMWs:
2008-2012 E82 BMW 128i 1M Coupe
2008-2010 E82 BMW 135i
2006-2011 E90 BMW 325i 325xi 328i 328xi 328i xDrive 330i 330xi 335is - Sedan
2006-2010 E90 BMW 335i 335xi 335i xDrive - Sedan
2006-2012 E91 BMW 325xi 328i 328xi 328i xDrive - Wagon
2007-2013 E92 BMW 328i 328xi 328i xDrive 335is - Coupe
2007-2010 E92 BMW 335i 335xi 335i xDrive - Coupe
2007-2013 E93 BMW 328i - Convertible
2007-2010 E93 BMW 335i - Convertible
2006-2010 E60 BMW 525i 525xi 530i 530xi 528i 528xi 528i xDrive 535i 535xi 535i xDrive
2011 F10 BMW 528i
2006-2010 E83 BMW X3 3.0i X3 3.0si
2007-2013 E70 BMW X5 3.0si
2006-2008 E85 BMW Z4 3.0i Z4 3.0si
2009-2011 Z4 BMW Z4 sDrive30i Z4 sDrive35i Z4 sDrive35is

If you have ever attempted to do a valve job or cylinder head gasket project on an M42, M44, M50, or M52 engine you know that the repair manual will refer to the special BMW timing tool kit. This tool kit includes a flywheel locating lock pin, and a special set of camshaft locators that lock the cams in a precise location. The tools are very easy to install. The kit is specifically designed to hold the engine and cams in proper timing during the cylinder head removal and re installation process. This avoids the chance of bending the valves doing the head install process. The precision ground holding blocks lock over the square ends of both intake and exhaust cams. The CNC machined flywheel locating pin passes through a hole in the rear of the engine block and passed through a machined hole in the flywheel.

To avoid improper cam timing on the latest BMW engines, the factory has devised a cam timing system that locks the crankshaft and cams into a specific position prior to cylinder head removal. This method was devised to avoid any misalignment, resulting in piston to valve damage. Unfortunately without these tools re-timing the camshafts after a valve job is almost impossible. The factory specification manual does not supply installation specifications. This cam timing kit includes all the necessary components to do the job.

This item fits the following BMWs:
1990-1991 E30 BMW 318i 318is 318ic
1992-1998 E36 BMW 318i 318is 318ti 318ic 323is 323ic 325i 325is 325ic 328i 328is 328ic M3
1999-2005 E46 BMW 323i 323ci 325i 325ci 325xi 328i 328ci 330i 330ci 330xi

NOTE: Not compatible with S50B30 and S50B32 Euro engines!If you have ever attempted to do a valve job or cylinder head gasket project on an M42, M44, M50, or M52 engine you know that the repair manual will refer to the special BMW timing tool kit. This tool kit includes a flywheel locating lock pin, and a special set of camshaft locators that lock the cams in a precise location. The tools are very easy to install. The kit is specifically designed to hold the engine and cams in proper timing during the cylinder head removal and re installation process. This avoids the chance of bending the valves doing the head install process. The precision ground holding blocks lock over the square ends of both intake and exhaust cams. The CNC machined flywheel locating pin passes through a hole in the rear of the engine block and passed through a machined hole in the flywheel.

 

Valvetronic Actuator Replacement Kit

Revitalize your engine's Valvetronic system with the Valvetronic Actuator Replacement Kit. This comprehensive kit includes the Valvetronic actuator, actuator gasket, and valve cover gaskets, ensuring a complete overhaul for optimal performance. Crafted to OEM specifications, these components guarantee precise fitment and reliable functionality. Say goodbye to Valvetronic issues and restore your engine's efficiency with this all-in-one replacement kit.

This gauge ensures that the inlet and exhaust cams are aligned perfectly. Make sure the edges are on the correct sides of the cylinder head before using.

Includes two alignment pin's which is ideal for inspection and servicing the motor with the timing chain still attached. If you are going to be removing the timing chain for service, you will need to lock both cams. 

The Ultimate kit includes every thing the standard kit does along with, a second alignment bridge, flywheel lock pin, VANOS alignment tools. and 4 bolt crank socket.

This tool fits all S54 powered BMW, including: 
2001-2006 E46 BMW M3
2001-2002 E36/7 BMW Z3M Coupe Z3M Roadster
2006-2008 E85/6 BMW Z4M Coupe Z4M Roadster
 

Feeds oil to the VANOS unit from the oil filter housing.

When doing any sort of repair or maintenance there is no replacement for genuine factory parts. Turner Motorsport carries the Genuine BMW brand with pride and has the parts you need to complete your next project with confidence.

Fits the following BMW engines:
M52, S52, M54

Not only will this kit stop most E90 oil leaks, it's the perfect addition for ignition coil or spark plug replacement! Oil leaks - and the damage they can cause - seem to be the worst annoyances on these cars. The biggest source of an oil leak is from the valve cover, followed by the oil filter housing, Valvetronic seal, camshaft seals, and the eccentric shaft sensor seal. Once the oil leaks, and if ignored for an extended time, the oil will contaminate vital electrical sensors. This is especially the case with ignition coils and also the eccentric shaft sensor on the Valvetronic shaft at the top of the cylinder head. During any ignition coil and spark plug replacement take a close look inside for any oil pooling at the bottom. We have been seeing valve cover oil leaks as soon as 40,000 miles. We look for oil leaks on every E90 that comes into our shop.

We have put together this package of valve cover gaskets and other related gaskets and seals for you to fully overhaul the N52 valve cover and put a stop to those pesky oil leaks. This package has the replacement parts for N52 engines built up to 10/2006 and includes:
 

• 11127581215 - N52 valve cover gasket set
• 11120409288 - N52 aluminum valve cover bolts (1-time use only, not re-usable)
• 11377516302 - N52 Valvetronic gasket
• 11127528242 - N52 eccentric shaft sensor seal

These are all Genuien BMW parts. Replacement of these gaskets and seals is straight-forward but a long process. BMW dealers typically charge for over eight hours of labor. If you have replaced spark plugs before you should be capable of this repair. In addition, there are several other parts to replace while you're in the vicinity: camshaft sensor o-rings, oil filter housing profile gasket, VAN0S solenoids, and the eccentric shaft sensor. These other parts, except the eccentric shaft sensor (see below), are replaceable without removing the valve cover but are more easily accessed during the valve cover work.

Eccentric Shaft Sensor: This is the position sensor that relays the eccentric shaft's position back to the DME. It's located at the front of the engine and is only accessible with the valve cover off. Over time the seal around the sensor comes loose and oil is allowed to blow out of the cam cover and it eventually finds its way into the sensor (which will eventually fail). Without a functioning sensor your E90 can experience poor running, hesitation, poor performance, jerky shifts, and sluggish response. It's easy to check and see if oil has accumulated inside the sensor: unbolt the engine trim cover (the outer cover with the BMW roundel), unplug the sensor, and look inside. If oil is present inside or even around the sensor itself, plan on replacing this sensor during your next ignition coil, spark plug, and/or valve cover gasket work.

This valve cover kit fits the following BMWs:
2006 E90 BMW 325i 325xi 330i 330xi - Sedan
2006 E91 BMW 325xi - Wagon
2006 E60 BMW 525i 525xi 530i 530xi
2006-10/2006 E85 BMW Z4 3.0i Z4 3.0si

Enhance your BMW's performance with this comprehensive valve cover assembly, complete with a sealing gasket and engine cover mounts.

• Key Benefits:
  • Comprehensive valve cover assembly for BMW engines
  • Includes sealing gasket for optimal performance
  • Engine cover mounts ensure a secure fit
  • Enhances overall engine efficiency and longevity

Keeping the oil inside your engine is extremely important to performance. Between oil change intervals, your oil can dip to dangerous levels if there is a leak you may not be aware of. The valve cover is an extremely common place for this to happen. BMW straight six engines are notorious for leaky valve cover gaskets. Years of exposure to extreme temperature change degrades the gaskets and causes failure. Replace yours to keep your engine oil in your vehicle.

This valve cover gasket set fits the folowwing BMWs with the M54 engine:

E39 525i 530i For vehicles with production date from 09/2002 
E46 325Ci 325i 325Xi 330i 330Ci 330Xi For vehicles with production date from 09/2002 
E53 X5 For vehicles with production date from 09/2002 
E60 525i 530i 
E83 X3
Z4 2.5i 3.0i

Located on the intake side of the cylinder head, this sensor relays the position of the camshaft to the computer in order to determine proper ignition timing. When this sensor fails the engine will generally log a fault code and may place the vehicle into "limp" mode. When this happens it is advised to stop driving the vehicle and address the issue immediately as premature wear or long term damage to the engine is possible.

When doing any sort of repair or maintenance there is no replacement for genuine factory parts. Turner Motorsport carries the Genuine BMW brand with pride and has the parts you need to complete your next project with confidence.

OE BMW reference number: 12147539165
 

We also carry a this sensor with the required o ring Here

This part fits the following BMWs:
1998 - 2004 E39 Touring 525i 528i 
1996 - 2004 E39 Sedan 525i 528i 530i  
1999 - 2006 E46  323i 323ci 325i 325ci 325xi 328i 328ci 328xi 330i 330ci 330xi 

Failing ignition coils or plugs can cause sputtering, rough idle, hesitation on acceleration, misfires, and a check engine light. Replace it with this blue Dinan Performance ignition service kit!

The kit includes:

• 6 Dinan Coils with locks
• 6 Bosch spark plugs
• 1 packet of American Grease Stick dielectric grease

Dinan ignition coils features:

• Up to 10% more energy output than stock.
• Blue housing with Dinan Logo.
• True upgrade, not just aesthetic.
• Direct plug-and-play.