Find Parts That Fit Your Vehicle

BMW Fuel System Parts

Looking for a BMW fuel pump, BMW gas cap or other BMW fuel system related items? You've found the right place. Your BMW fuel delivery system is a critical system, and any failure can rended your BMW dead in the water. Whether your fuel pump has stopped pumping, a fuel injector is clogged or not spraying, or your gas cap is either lost or not properly sealing, we likely have what you are looking for. We stock thousands of BMW fuel system parts so if you don't see what you are looking for, just give us a call.

Sub-Categories

Sort By:

Fuel-It! - Corporate Logo
T#:21275574
Part#: FFK-N20/6F-FK
Ships on Sep 9, 2026
$ 369.99 USD
Free Shipping on orders $49 and up
This is a complete plug and play kit to install a Bluetooth ethanol sensor in about 30 minutes! The kit includes the following: New 5/16" E85 compatible fuel lines for your engine bay Genuine Continental ethanol sensor Fuel-It! Bluetooth analyzer Plug and play harness ​​Includes both Bluetooth App & 5v analog output for JB4 or flash tuning NOTICE: If you have an N26 motor type, you will need to retrofit the HPFP supply line to part number 13537585415 to be compatible with this kit. *For the BMW F-series JB4 platform connect the white wire to position #14 on the JB4 25 pin harness. Select WMI Ethanol Setup option 1 to enable pin location 14/15/16 flex fuel input. *Ethanol Sensors don't actually read the ethanol content, the readings are based on the absence of gasoline, so if your fuel is contaminated your ethanol readings may be artificially elevated.
Show More Show Less
Fuel-It! - Corporate Logo
T#:21242695
Part#: FFK-N5XA
In Stock
Starting at $ 485.99 USD
Free Shipping on orders $49 and up
Starting at $ 485.99 USD
Free Shipping on orders $49 and up
If you are running E85 or ethanol mixes in your BMW, you need this kit! This is a complete plug and play kit to install a Bluetooth ethanol sensor in your E-Chassis BMW. This kit replaces the stock fuel lines from the fuel tank to the engine bay with an upgraded -6an E85 compatible fuel line and adds an ethanol sensor and Bluetooth analyzer to monitor your ethanol content. Includes both Bluetooth App & 5v analog output for JB4 or flash tuning. For your fuel line upgrade, choose the option that supports your current configuration. HPFP to the fuel tank: (Stock) This upgrade replaces both stock fuel lines with one upgraded continuous fuel line from the fuel tank to the HPFP and adds the ethanol sensor. Port Injection to the fuel tank: If you are running our port injection kit, this upgrade replaces the stock fuel lines from the tank to the engine bay, integrates the ethanol sensor and then utilizes a Y adapter to supply the HPFP and PI with fuel. Our custom fittings remove those tee's and extra fittings for a cleaner high flow setup. Non-Fuel-It! port injection to fuel tank: Choose this option if you are running a port injection kit that we did not manufacture or sell. This kit includes a longer 18" feedline from the Y to the port injection rail. You then cut the feed line to the length you need and install the included -6an female fitting or -6an female elbow to make the connection to your port injection rail. All of these kits utilize the BMS custom billet aluminum fittings to integrate with the stock fittings so no modifications are needed. *For the BMW N54 E-series JB4 platform connect the white wire to position #15 on the JB4 25 pin harness. Select WMI Ethanol Setup option 1 to enable pin location 15/16 flex fuel input. *For the BMW N55 E-series JB4 platform connect the white wire to position #16 on the JB4 25 pin harness. Select WMI Ethanol Setup option 1 to enable pin location 15/16 flex fuel input. *Ethanol Sensors don't actually read the ethanol content, the readings are based on the absence of gasoline, so if your fuel is contaminated your ethanol readings may be artificially elevated.
Show More Show Less
Genuine MINI - Corporate Logo
T#:390651
Part#: 13517588879KT
In Stock
$ 1,584.53 USD
Free Shipping
$ 1,584.53 USD
Free Shipping
This high pressure pump is used for your direct-injected vehicle. They will usually fail when the camshaft follower wears through and destroys the pump shaft or they can't put out the proper pressure after it has aged. When replacing the pump, make sure to also replace the cam follower as this is most likely worn or destroyed as well.
Show More Show Less

Fuel Pump - Priced Each
2X Entries Into Our F80 M3 Sweepstakes
URO - Corporate Logo
T#:14783539
Part#: 16112755083
Back Ordered
$ 159.99 USD
Free Shipping on orders $49 and up

Spool Performance - Corporate Logo
T#:26271786
Part#: SP-FX-200-N55-NE
In Stock
$ 1,799.00 USD
Free Shipping on orders $49 and up
The FX-200 is an advanced high-pressure fuel pump engineered specifically for the BMW N55 engine, replacing our previous FX180 model. Featuring a larger bore size than the stock pump, it provides nearly double the flow rate. This pump is fully E85 fuel compatible and integrates seamlessly into the system without requiring any wire cutting or splicing. The enhanced flow capacity enables the use of higher ethanol concentrations and supports sufficient fueling for larger turbochargers.
Show More Show Less
High Pressure Fuel Pump - 13517595339
10X Entries Into Our F80 M3 Sweepstakes
Bremmen Parts - Corporate Logo
T#:36066211
Part#: 13517595339
In Stock
$ 277.99

This product was last offered at the strikethrough price on
05-03-2026

$ 214.99 USD
Limited Qty Sale
Free Shipping on orders $49 and up
$ 277.99

This product was last offered at the strikethrough price on
05-03-2026

$ 214.99 USD
Limited Qty Sale
Free Shipping on orders $49 and up

The High Pressure Fuel Pump (HPFP) is a point of weakness in many BMW engines and fuel systems. If this goes it will prevent your car from running or starting due to fuel starvation. Restore your fuel system's operation with high quality OE BMW fuel pump from Bremmen Parts.

Bremmen Parts High-Pressure Pump This item fits the following BMW Chassis: E70 X5M,E71 X6M,E70 X5,E71 X6,F01,F02,F10,F12,F13

Fits BMW Engines including: N63,N63N,S63

Show More Show Less

High Pressure Fuel Pump Gasket
2X Entries Into Our F80 M3 Sweepstakes
URO - Corporate Logo
T#:592759
Part#: 11127588416
In Stock
$ 7.99 USD
Free Shipping on orders $49 and up
A bad fuel pump gasket can spell all sorts of trouble when you least expect it. Commonly, low fuel pressure will cause a vehicle to not start or run, or can cause it to die out on the road.
Precision Raceworks - Corporate Logo
T#:35559426
Part#: 601-0338
Ships in 9 Business Days
$ 1,574.99 USD
Free Shipping on orders $49 and up
The Precision Raceworks X3/X3M (G01/F97) Stand Alone Auxiliary Fuel System is the highest-performing and most stable low-pressure fuel system on the market! Forget about how things have been done and embrace the benefits of dedicated fueling for your port injection! Since direct injection came out on modern BMWs, enthusiasts have been adding port injection. With this came the need to upgrade the low-pressure fuel system to keep up. Historically this was done by increasing the output of the main fuel system. Unfortunately, the main fuel pump is controlled using PWM by a factory-programmed controller designed to reduce output when target fuel pressure (typically 5 bar) is exceeded, creating a constant battle when pumps are added or upgraded. This limits upgraded fuel pumps from performing to their full potential. Additionally, the high-pressure pump control system dumps fuel back into the low-pressure system at high pressure low volume resulting in oscillations of the low-pressure fuel system. Because of this, the DI system in the car is required to constantly make corrections to keep target AFR in check. With this stand-alone low-pressure fuel system dedicated to your port fueling that is a thing of the past! Get rock-solid fuel pressures at any pressure, run fuel pressures that are 1:1 scalable to boost pressure, flow more fuel with dedicated lines, run smaller injectors and still get more fuel than you did with large injectors (allowing for higher resolution), put less demand on the car’s DI system to correct for fluctuations in pressure, even your tuner will be grateful as the system makes tuning of port fueling even easier and more accurate, the list of benefits goes on and on! Features & Benefits Billet Aluminum top hat with 3 high-flow fuel ports Dedicated fuel pump(s) for port injection system Optimal pump location resistant to fuel slosh under acceleration Fully adjustable 1:1 scaling billet fuel pressure regulator 10-micron USA made Microglass fuel filter (Ideal for E85) Smooth bore high flow PTFE fuel feed & return lines (AN6) All billet connections for both fuel line fittings and top-hat Plug and play connectors inside and outside* the top hat Configurable pump activation harness (see instructions for more details) Increased injector flow (when using 1:1 regulator feature vs static) Compatible with all stock or upgraded primary fuel pumps Easily expandable and upgrade-able for more fuel All components and parts feature 100% Ethanol Compatibility The AFS.460 dedicated auxiliary fuel system comes with all** necessary components to provide a dedicated fuel system for port injection. Featuring a single Walbro 535 (F9000295) fuel pump which flows 460LPH at 3 bar. Pump flow 43.5 psi-a : 460 lph Recommended base pressure: 43.5 psi-g Maximum Fuel Pressure: 110 psi-g Number of Fuel Output Ports: 2 Number of Fuel Return Ports: 1 Pump 1: Walbro 535 (F90000295) Pump 2: N/A Available (unused) Electrical Connections: 4* Total System Weight: 11 lbs (including fuel lines and wiring harness) *At time of install some wiring in the car may need to be cut and spliced to connectors included in this kit on older models **The AFS kits are designed for use with a port injection kit where the fuel rail is mounted above the manifold. To use with a plate-style spacer PI, please reach out to us directly at 713-770-6977 or [email protected]
Show More Show Less

URO MAP Sensor - BMW M57 3.0L
2X Entries Into Our F80 M3 Sweepstakes
URO - Corporate Logo
T#:50031881
Part#: 13627792260
In Stock
New Item
$ 70.99 USD
Free Shipping on orders $49 and up
Replaces failing pressure sensor.

Genuine BMW - Corporate Logo
T#:191296
Part#: 16127244726
In Stock
6% off MSRP $ 88.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 83.99 USD
Free Shipping on orders $49 and up
6% off MSRP
$ 88.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 83.99 USD
Free Shipping on orders $49 and up


Genuine BMW Front Fuel Feed Line -
This item fits the following BMW Chassis:
F30,F31

Schwaben BMW Fuel Line Disconnect Tool
10X Entries Into Our F80 M3 Sweepstakes
Schwaben - Corporate Logo
T#:384267
Part#: 015345SCH01A
In Stock
Sale - Save 56% $ 26.99

This product was last offered at the strikethrough price on
04-28-2026

$ 11.99 USD
Free Shipping on orders $49 and up
Sale - Save 56%
$ 26.99

This product was last offered at the strikethrough price on
04-28-2026

$ 11.99 USD
Free Shipping on orders $49 and up

This tool is designed to work with the difficult to release fuel lines on BMW. Don't risk damaging these costly lines by using the wrong tool. Seals can easily be damaged if not released properly. 

Features:

  • Small overall design allows tool to work in hard to reach areas
  • Made from aluminum for strong durable use
  • Green anodized finish.
Show More Show Less
Fuel Pump W/ Fuel Level Sensor
2X Entries Into Our F80 M3 Sweepstakes
URO - Corporate Logo
T#:592100
Part#: 16146766177
In Stock
$ 133.99 USD
Free Shipping
$ 133.99 USD
Free Shipping


Sealing Ring
2X Entries Into Our F80 M3 Sweepstakes
URO - Corporate Logo
T#:553920
Part#: 16146750467
Ships in 1 Business Day
$ 10.99 USD
Free Shipping on orders $49 and up
Fuel Filter Kit - M57
10X Entries Into Our F80 M3 Sweepstakes
Packaged by Turner - Corporate Logo
T#:56291065
Part#: 13327811227KT2
In Stock
New Item
$ 55.42 USD
Free Shipping on orders $49 and up
This fuel service kit pairs a high flow OEM replacement fuel filter with a fresh dampening ring and securing hex bolt. By replacing the filter and hardware together, you ensure fuel pressure stability
Dorch Engineering - Corporate Logo
T#:55533487
Part#: DE-582-25TS
In Stock
New Item
$ 1,999.00 USD
Free Shipping on orders $49 and up
The Dorch Engineering DS25 B58 Gen2 HPFP Upgrade provides the necessary high volume fueling required for high-horsepower builds and heavy ethanol scaling. This next-generation pump operates at a massive 350 bar, bringing unprecedented volumetric efficiency
Show More Show Less

Fuel Injector Installation Kit
10X Entries Into Our F80 M3 Sweepstakes
Assembled By ECS - Corporate Logo
T#:56507874
Part#: 13537577649KT2
In Stock
New Item
$ 104.99 USD
Free Shipping on orders $49 and up

Bosch - Corporate Logo
T#:33512921
Part#: 13537808089RKT
In Stock at Vendor
$ 4,165.99

This product was last offered at the strikethrough price on
03-26-2026

$ 2,860.99 USD
Free Shipping on orders $49 and up
$ 2,860.99 USD
Free Shipping on orders $49 and up
The factory fuel injectors in the M57N2 diesel engine are generally reliable, but they can still experience the same problems common to direct injection systems. A frequent issue is carbon buildup on the injector tip, which can lead to poor spray patterns, reducing fuel atomization. This results in lower engine power or rough idling due to improper fuel ignition. Other problems, such as clogged injectors from contaminated fuel or internal injector failure, can also cause similar symptoms. If your diesel engine is experiencing rough idling, reduced power, or poor fuel efficiency, this replacement injector set featuring Bosch injectors is an excellent solution to resolve these issues and restore optimal engine performance. Additionally, this kit includes a replacement overflow oil line, which is prone to clogging in high-mileage vehicles. Replacing it along with your fuel injectors is recommended for best results.
Show More Show Less
Elring Fuel Injector O-Ring - N52 3.0L
2X Entries Into Our F80 M3 Sweepstakes
Elring - Corporate Logo
T#:362791
Part#: 13647531313
In Stock
$ 3.99

This product was last offered at the strikethrough price on
04-07-2026

$ 2.03 USD
Free Shipping on orders $49 and up
$ 2.03 USD
Free Shipping on orders $49 and up

These o-rings need to be replaced any time that the fuel injectors are pulled. These have a habit of swelling and can tear or suffer other damage when being reinstalled or when removed. If the seal is not tight, this could lead to a fuel leak or worse.This Elring o-ring will ensure the seal is nice and tight

Elring is one of the biggest OEM names in the manufacturing of high quality gaskets that are available for very affordable prices. Elring has supplied many automotive names for years with the gaskets that seal your car's components from day 1 so you can rest assured that these components will last for a long time to come!

Fits the following BMW engines:
N52 3.0L

Show More Show Less

Fuel Injector Set
10X Entries Into Our F80 M3 Sweepstakes
Packaged by Turner - Corporate Logo
T#:15710786
Part#: 13647597870-KT
In Stock
$ 1,093.99

This product was last offered at the strikethrough price on
05-12-2026

$ 898.99 USD
Free Shipping on orders $49 and up
$ 898.99 USD
Free Shipping on orders $49 and up

Refresh your old injectors with these OE fuel injectors! Get your car running its best and prevent any failures or issues prematurely!

x6 injector x6 decoupling element

Bosch - Corporate Logo
T#:33512924
Part#: 13537808089IKT
In Stock at Vendor
$ 4,040.99

This product was last offered at the strikethrough price on
03-26-2026

$ 2,735.99 USD
Free Shipping on orders $49 and up
$ 2,735.99 USD
Free Shipping on orders $49 and up
The factory fuel injectors in the M57N2 diesel engine are generally reliable, but they can still encounter the typical issues faced by direct injection systems. A common problem is carbon buildup on the injector tip, which can lead to poor spray patterns, resulting in inadequate fuel atomization. This causes reduced engine power or rough idling due to improper fuel ignition. Similar issues can arise from clogged injectors caused by contaminated fuel or internal injector failure. If your diesel engine is experiencing rough idling, reduced power, or poor fuel efficiency, this replacement injector set featuring Bosch injectors is an ideal solution to resolve these issues and restore proper engine performance. Each Bosch injector comes with preinstalled sealing washers and o-rings, making them ready for immediate installation.
Show More Show Less

Bosch - Corporate Logo
T#:20946736
Part#: 13532247156
In Stock
$ 3.99 USD
Free Shipping on orders $49 and up
Located between the base of the fuel injector and the cylinder head - one required per injector

Bootmod3 - Corporate Logo
T#:31390587
Part#: BM3FFKTFH
In Stock
$ 599.00

This product was last offered at the strikethrough price on
08-10-2026

$ 572.99 USD
Limited Qty Sale
Free Shipping on orders $49 and up
$ 599.00

This product was last offered at the strikethrough price on
08-10-2026

$ 572.99 USD
Limited Qty Sale
Free Shipping on orders $49 and up
BM3 is proud to bring out this truly awesome product that makes getting the required Flex Fuel hardware on your BMW with incredible ease and minimal effort, in your own driveway. BM3's kit is entirely plug-and-play with the factory vehicle harness. No cutting or splicing of OEM wiring/connectors. It installs in minutes and can be removed without a trace on the car! BM3's team used SolidWorks to design a Flow Optimized Flex Fuel Sensor Adapter (FFSA) to ensure fuel flow is unobstructed and with no added pressure drop at full fuel pump flow from the fuel tank to your motor when our kit is installed. This is important when pushing the factory fuel system with all the power Ethanol can provide over petrol! Flex fuel sensor housing is designed to neatly install into the factory BMW fuel hat location. Flex Fuel Sensor Adapter also contains two 1/8 NPT ports that allow installation of an auxiliary Fuel Pressure sensor for vehicles that don’t come with an OEM one from the factory for future use. Depending on fitment, either port can be used. Install the BM3 Flex Fuel Plug and Play Kit and flash your flex fuel enabled BM3 OTS MultiMap or Custom Map in minutes and you’re off to the races never worrying about alcohol/petrol blend % in your fuel tank. It does not get better or easier than this! BM3 FlexFuel Plug and Play Kit: Minutes to install at home as opposed to hours at a shop with car up on lift fabricating/cutting into factory fuel lines and splicing/cutting/pinning into OEM electrical 4+ hours in time/cost savings to get going on Flex Fuel as compared to most other kits that require making custom fuel lines, fittings and custom wiring! Fully reversible/removable and back to stock without a trace in minutes Custom 3-piece Aluminum-6061 Flex Fuel sensor adapter with built-in sensor bypass to allow for obstruction free fuel flow made to fit in the vehicle factory fuel hat area below the rear seat All connecting points sealed with fuel safe Viton o-rings Flex Fuel Sensor Adapter housing provides additional 1/8 NPT ports for optional Fuel Pressure sensor addition to vehicles without a factory one for BM3 CustomROM v2 support CANBUS Enabled Ethanol Content Analyzer (ECA) that integrates with BM3 CustomROM for complete and seamless conversion of your BMW to FlexFuel for BM3 Flex Fuel enabled OTS MultiMaps and custom tunes with your BM3 tuner of choice Power/CANBus 4-wire plug and play harness 100% Fully Plug and Play harness to the BMW Fuel Controller connectors (EKP3) on S55, N55 vehicles 100% Fully Plug and Play harness on the BMW Body Domain Controller (BDC/FEM) connector on Gen1 F-series B48/B58 Continental Flex Fuel sensor 3-wire harness Custom Aluminum-6061 CANBus Enclosure for the BM3 ECA board Custom, kink-free teflon braided line allowing plug-and-play installation with the OEM fuel hat and factory 5/16” or 3/8” fuel feed line. No cutting or new lines required. -6 AN fitting by Racetronix NOTE: OEM FUEL HAT LOCATION KIT IS INTENDED FOR OEM FUEL PUMP AND ASSOCIATED WIRING. ANY VARIATIONS TO FUEL LINES OR FUEL PUMPS MAY NOT BE COMPATIBLE. USE THE ENGINE BAY INSTALLATION KIT WHERE AVAILABLE INSTEAD.
Show More Show Less
OEM Hengst Fuel Filter - E65 E66 N62
5X Entries Into Our F80 M3 Sweepstakes
5X Entries For Our G87 M2 Sweepstakes! We Price Match - Give Us A Call or Chat! Hengst is our preferred OEM filtration supplier!
Hengst - Corporate Logo
T#:582237
Part#: 16126750475
In Stock
$ 59.99 USD
Free Shipping on orders $49 and up
This is an OEM Hengst fuel filter that removes dirt and other particle contaminants from your fuel. A clogged fuel filter makes it difficult for your engine to get all the fueling it needs. Filters commonly clog from a deteriorating gas tank, bad fuel, or other debris in the fuel system. A fresh fuel filter addresses many fuel-related problems including surging, stalling, cold start issues, and poor performance under a variety of conditions.
Show More Show Less


MINI R56 N12 N16 Fuel Pump - Each
10X Entries Into Our F80 M3 Sweepstakes
Bremmen Parts - Corporate Logo
T#:6859960
Part#: 16112755083
Ships on Nov 30, 2026
$ 144.99

This product was last offered at the strikethrough price on
02-27-2026

$ 99.99 USD
Free Shipping on orders $49 and up
$ 99.99 USD
Free Shipping on orders $49 and up

MINI R56 N12 N16 Fuel Pump is an essential replacement part for restoring fuel pressure and ensuring reliable engine starts. This unit is typically replaced when there is a loss of fuel pressure or if the vehicle does not start despite having a good spark and a properly running engine. The fuel pump, which is mounted inside the fuel tank, includes a level sensor to monitor fuel levels accurately. Installing this fuel pump will help get the MINI back to optimal running condition.

  • Restores Fuel Pressure: Essential for resolving issues with fuel pressure and engine starting.
  • Includes Level Sensor: Monitors fuel levels to ensure accurate readings.
  • Direct Fit: Designed to be mounted inside the fuel tank for easy replacement.
  • Reliable Performance: Helps restore the MINI to optimal running condition.
Show More Show Less
Pro-Line Injector And Glow Plug Grease - 20g
10X Entries Into Our F80 M3 Sweepstakes
Liqui-Moly - Corporate Logo
T#:49787695
Part#: 22243
In Stock
$ 6.99 USD
Free Shipping on orders $49 and up
This high-performance lubricant is formulated to prevent moisture ingress and oxidation, which are the primary causes of "frozen" injectors and glow plugs.
MINI R53 Fuel Pump W/ Fuel Level Sensor
10X Entries Into Our F80 M3 Sweepstakes
Bremmen Parts - Corporate Logo
T#:28138164
Part#: 16146766177
In Stock
Sale - Save 3% $ 84.99

This product was last offered at the strikethrough price on
05-03-2026

$ 82.11 USD
Free Shipping on orders $49 and up
Sale - Save 3%
$ 84.99

This product was last offered at the strikethrough price on
05-03-2026

$ 82.11 USD
Free Shipping on orders $49 and up

MINI R53 Fuel Pump with Fuel Level Sensor

For Mini owners seeking a reliable fuel pump replacement, the MINI R53 Fuel Pump with Fuel Level Sensor is an essential component. This fuel pump ensures efficient fuel delivery to the engine, maintaining optimal performance. With its integrated fuel level sensor, it provides accurate fuel level readings, ensuring Mini enthusiasts are always informed.

  • Ensures efficient fuel delivery to the engine
  • Maintains optimal performance
  • Integrated fuel level sensor for accurate readings
  • Keeps Mini enthusiasts informed about fuel levels
Show More Show Less

Fuel Injector Gasket Ring - BMW N47, N57, M57, B57
10X Entries Into Our F80 M3 Sweepstakes
Bavarian Autosport - Corporate Logo
T#:17871160
Part#: 13532247156
In Stock
$ 0.99 USD
Limited Qty Sale
Free Shipping on orders $49 and up
$ 0.99 USD
Limited Qty Sale
Free Shipping on orders $49 and up
Seals the fuel injector to the engine

Febi Relay - Replaces White/Green
We Price Match - Give Us A Call or Chat!
Febi - Corporate Logo
T#:16375128
Part#: 61368373700
Ships on Nov 18, 2026
Sale - Save 28% $ 15.99

This product was last offered at the strikethrough price on
05-15-2026

$ 11.56 USD
Free Shipping on orders $49 and up
Sale - Save 28%
$ 15.99

This product was last offered at the strikethrough price on
05-15-2026

$ 11.56 USD
Free Shipping on orders $49 and up
This relay is often the fuel pump relay for many BMW models. To ensure the relay is correct for your car please check the pin locations
Dorch Engineering - Corporate Logo
T#:55713511
Part#: DE-582-ECA-242
In Stock
New Item
$ 549.00 USD
Free Shipping on orders $49 and up
$ 549.00 USD
Free Shipping on orders $49 and up
This hardware package gives your BMW powerplant the ability to scale output dynamically based on your exact ethanol blend. No more draining the tank or flashing different maps at the gas station

Dorch Engineering - Corporate Logo
T#:55533476
Part#: DE-55-15B
In Stock
New Item
$ 1,149.00 USD
Free Shipping on orders $49 and up
$ 1,149.00 USD
Free Shipping on orders $49 and up
The Dorch DS15B High-Pressure Fuel Pump Upgrade is the definitive choice for drivers demanding uncompromised fuel delivery under heavy load. The stock pump simply cannot keep up with the volume required for upgraded turbos
Show More Show Less
Bosch - Corporate Logo
T#:51356041
Part#: BB48G2FIRKT
Ships in 2 Business Days
New Item
$ 658.99

This product was last offered at the strikethrough price on
03-31-2026

$ 492.99 USD
Free Shipping on orders $49 and up
$ 492.99 USD
Free Shipping on orders $49 and up
This Fuel Injector Replacement Kit includes new injectors and hardware to service your fuel injection system, eliminating rough idle, low power, and check engine lights due to faulty fuel injectors.

Dorch Engineering - Corporate Logo
T#:55713498
Part#: DE-581-ECA-14TU
In Stock
New Item
$ 549.00 USD
Free Shipping on orders $49 and up
The Dorch Engineering CAN-based Flex Fuel ECA Kit delivers real-time ethanol monitoring directly to your BMW's DME. Designed explicitly for Gen1 B58

Dorch Engineering - Corporate Logo
T#:55533507
Part#: DE-55-25B
In Stock
New Item
$ 1,699.00 USD
Free Shipping on orders $49 and up
The Dorch Engineering DS25 N55 HPFP Upgrade is the definitive solution for enthusiast drivers looking to extract maximum power from their N55. Optimized for high output setups, this upgraded pump delivers a critical 25% bump in fueling capacity over the factory unit
Show More Show Less
Dorch Engineering - Corporate Logo
T#:55461363
Part#: DE-581-25A
In Stock
New Item
$ 1,799.00 USD
Free Shipping on orders $49 and up
The Dorch Engineering DS25 HPFP Upgrade for the Gen 1 B58 engine is the definitive hardware upgrade for enthusiasts looking to safely extract maximum performance from their powerplants. Designed to eliminate the primary bottleneck in the B58 fueling system
Show More Show Less
Dorch Engineering - Corporate Logo
T#:55533509
Part#: DE-581-30A
In Stock
New Item
$ 2,399.00 USD
Free Shipping on orders $49 and up
The Dorch Engineering DS3 B58 Gen 1 HPFP Upgrade is the ultimate solution for drivers looking to lift the fueling restrictions on their B58 powerplant. Optimized for high-output setups, this upgraded pump ensures your injectors are supplied with the precise volume
Show More Show Less


Dorch Engineering - Corporate Logo
T#:55533486
Part#: DE-582-25B
In Stock
New Item
$ 1,999.00 USD
Free Shipping on orders $49 and up
$ 1,999.00 USD
Free Shipping on orders $49 and up
The Dorch Engineering DS25 B58 Gen2 HPFP Upgrade provides the necessary high volume fueling required for high-horsepower builds and heavy ethanol scaling. This next-generation pump operates at a massive 350 bar, bringing unprecedented volumetric efficiency
Show More Show Less
Dorch Engineering - Corporate Logo
T#:55461365
Part#: DE-581-25C
In Stock
New Item
$ 1,799.00 USD
Free Shipping on orders $49 and up
$ 1,799.00 USD
Free Shipping on orders $49 and up
The Dorch Engineering DS25 HPFP Upgrade for the Gen 1 B58 engine is the definitive hardware upgrade for enthusiasts looking to safely extract maximum performance from their powerplants. Designed to eliminate the primary bottleneck in the B58 fueling system
Show More Show Less
Dorch Engineering - Corporate Logo
T#:55713497
Part#: DE-581-ECA-14
In Stock
New Item
$ 549.00 USD
Free Shipping on orders $49 and up
The Dorch Engineering CAN-based Flex Fuel ECA Kit delivers real-time ethanol monitoring directly to your BMW's DME. Designed explicitly for Gen1 B58

Dorch Engineering - Corporate Logo
T#:55533480
Part#: DE-58-ECA-M34
In Stock
New Item
$ 549.00 USD
Free Shipping on orders $49 and up
The Dorch Engineering S58 Flex Fuel ECA Kit bridges the gap between raw power and street usability. By utilizing a heavy-duty CAN-bus architecture rather than smartphone apps

Dorch Engineering - Corporate Logo
T#:55461364
Part#: DE-581-25B
In Stock
New Item
$ 1,799.00 USD
Free Shipping on orders $49 and up
$ 1,799.00 USD
Free Shipping on orders $49 and up
The Dorch Engineering DS25 HPFP Upgrade for the Gen 1 B58 engine is the definitive hardware upgrade for enthusiasts looking to safely extract maximum performance from their powerplants. Designed to eliminate the primary bottleneck in the B58 fueling system
Show More Show Less
E89 EKP PNP Cooler Kit - (Z4)
A Must For Cars With Upgraded LPFPs
Arc Terminator - Corporate Logo
T#:26471566
Part#: E89-EKP-PNP
Ships in 1 Business Day
Starting at $ 44.99 USD
Free Shipping on orders $49 and up
Starting at $ 44.99 USD
Free Shipping on orders $49 and up
The full plug-and-play EKPM3 / EKPM2 cooler kit is designed specifically for E89 BMWs using an EKPM3 or EKPM2 fuel pump control module. This is recommended for anyone using a low-pressure fuel pump that is larger than the OEM fuel pump. Please note that if you have an HW06 + (Slim EKPM3), you must choose the HW06 option, as the pre-HW06 housings will not fit. Installation Tips: https://arcterminator.com/pages/e90-e92-e93-ekp-cooler-install-instructions We recommend using Fuse #8, which is the cigarette lighter fuse to power this. It is a 20 amp fuse, which you will just need to pull out and put it into the empty slot of the fuse holder that comes with the kit. Then you'll need to put that fuse holder into the now empty #8 fuse slot. This ensures that the fan will only turn on when the ignition in the car is turned on. You'll also need trim removal tools, as well as a 10mm socket to remove and re-install the EKP module. We recommend using the stock grounding point that's above the EKP module or the EKP module's mounting points as the ground. The ring terminal with the kit will fit either location. The whole installation should take you between 30 - 45 minutes. The cooler housing is designed to fit over the EKP module just like the OEM housing and fits with plenty of room in the stock EKP location. The housing is 3D printed using durable PLA+ or PETG, depending on the color choice. The full kit is printed and assembled in the U.S.A. by Arc Terminator LLC. Full Kit Contents: 1x PNP EKPM3 / EKPM2 Cooler Housing With 5015 Fan 1x 14x14x6mm Heatsink With Thermal Tape 1x 14x9x5mm Heatsink With Thermal Tape 1x 9x9x5mm Heatsink With Thermal Tape (EKPM3 Kit) 2x 9x9x5mm Heatsink With Thermal Tape (EKPM2 Kit) 8x 4" Zip Ties 1x Alcohol Wipe 1x 2 Amp Mini Blade Fuse Why this kit exists: The EKPM3 and EKPM2 have been shown to overheat and cause vehicle shutdown issues when larger fuel pumps that draw more current than OEM are used. This shutdown comes from critical components on the EKPM3 and EKPM2 overheating when larger current draws are coming from the fuel pump. The PNP kit comes with heatsinks for the most heat-sensitive and heat-producing components in the EKPM3 / EKPM2 to further increase cooling effectiveness. When paired with a potent 5015 blower fan that directs a large amount of airflow through the cooler housing, the EKPM3 / EKPM2 stays significantly cooler, which prolongs the life of the module. We also recommend anyone using a larger fuel pump than OEM to properly code their EKP module with Pro-Tool's built-in "Voltage Fix" feature.
Show More Show Less

Decoupling Element - Each
10X Entries Into Our F80 M3 Sweepstakes
Bremmen Parts - Corporate Logo
T#:27105152
Part#: 13537577649
In Stock
$ 12.99 USD
Free Shipping on orders $49 and up

Decoupling Element - Each is a crucial component for BMW vehicles, specifically designed to ensure optimal injector installation. This high-quality metal ring is positioned at the end of the fuel injector, playing a vital role in maintaining proper alignment and function.

Features and Benefits:

  • Essential Component: Integral for correct injector installation and operation.
  • High-Quality Construction: Made from durable metal to withstand the rigors of engine performance.
  • Precision Fitment: Ensures proper alignment of the fuel injector, enhancing engine efficiency.
  • Easy Installation: Designed for straightforward installation without the need for modifications.
  • Compatibility: Suitable for a range of BMW models, ensuring versatile use.
Show More Show Less
Fuel Pressure Regulator Vacuum Hose - 13537560069
2X Entries Into Our F80 M3 Sweepstakes
URO - Corporate Logo
T#:26171672
Part#: 13537560069
Ships in 1 Business Day
$ 19.99 USD
Free Shipping on orders $49 and up
$ 19.99 USD
Free Shipping on orders $49 and up

Ensure optimal engine performance in your BMW with this vacuum hose from URO Parts. Designed to provide vacuum to the fuel pressure regulator, this hose plays a crucial role in preventing engine performance issues. Cracks, tears, or splits in the rubber hose can result in lean codes and misfires, necessitating immediate repair.

  • Provides vacuum to the fuel pressure regulator
  • Prevents engine performance issues
  • Cost-effective solution
  • High-quality construction by URO Parts
Show More Show Less

Bosch - Corporate Logo
T#:592027
Part#: 13537573801
Ships in 1 Business Day
$ 35.50

This product was last offered at the strikethrough price on
04-09-2026

$ 34.49 USD
Free Shipping on orders $49 and up
$ 34.49 USD
Free Shipping on orders $49 and up

CSF - Corporate Logo
T#:56001929
Part#: CSF8404
Ships in 3 Business Days
New Item
$ 300.00 USD
Free Shipping
$ 300.00 USD
Free Shipping
Eliminate fuel starvation on your high boost S58 or B58 build with this track engineered, billet aluminum secondary port injection rail built to handle extreme fueling demands.
Fuel-It! - Corporate Logo
T#:21275563
Part#: FFK-S55-FIP
Ships on Sep 9, 2026
$ 589.99 USD
Free Shipping on orders $49 and up
If you are running E85 or ethanol mixes in your BMW, you need this kit! This is a complete plug and play kit to install a Bluetooth ethanol sensor in your S55 BMW. This kit replaces the stock fuel lines from the fuel tank to the engine bay with an upgraded -6an E85 compatible fuel line and adds an ethanol sensor and Bluetooth analyzer to monitor your ethanol content. Includes both Bluetooth App & 5v analog output for JB4 or flash tuning. For your fuel line upgrade, choose the option that supports your current configuration. HPFP to the fuel tank: (Stock) This upgrade replaces both stock fuel lines with one upgraded continuous fuel line from the fuel tank to the HPFP and adds the ethanol sensor. Port Injection to the fuel tank: If you are running our port injection kit, this upgrade replaces the stock fuel lines from the tank to the engine bay, integrates the ethanol sensor and then utilizes a Y adapter to supply the HPFP and PI with fuel. Our custom fittings remove those tee's and extra fittings for a cleaner high flow setup. Non-Fuel-It! port injection to fuel tank: Choose this option if you are running a port injection kit that we did not manufacture or sell. This kit includes a longer 18" feedline from the Y to the port injection rail. You then cut the feed line to the length you need and install the included -6an female fitting or -6an female elbow to make the connection to your port injection rail. All of these kits utilize the BMS custom billet aluminum fittings to integrate with the stock fittings so no modifications are needed. *For the BMW F-series JB4 platform connect the white wire to position #16 on the JB4 25 pin harness. Select WMI Ethanol Setup option 1 to enable pin location 15/16 flex fuel input. *These kits are available for off-road use only *Ethanol Sensors don't actually read the ethanol content, the readings are based on the absence of gasoline, so if your fuel is contaminated your ethanol readings may be artificially elevated.
Show More Show Less
Fuel Pump
2X Entries Into Our F80 M3 Sweepstakes
URO - Corporate Logo
T#:592083
Part#: 16112755082
Back Ordered
$ 206.99 USD
Free Shipping
$ 206.99 USD
Free Shipping

Is your vehicle suffering from a loss of fuel pressure as it enters the engine? Or perhaps your car refuses to start despite having a functional engine with spark. In such cases, it's time to consider a replacement for this critical unit. This is a URO Branded product, meticulously designed to be mounted within the fuel tank. The fuel pressure pump, equipped with a level sensor, is the solution you need to get your MINI back on the road and running at its best.

Quick Diagnostic Tip:

When dealing with a high-pressure fuel pump in the front, you can swiftly diagnose a potential issue with the rear fuel pump. Simply listen for a distinct sound when you open the door or unlock your car. The rear fuel pump should emit a high-pitched, quick whine originating from the fuel tank, lasting only a few seconds. If this sound is absent, it could indicate a problem with the primary rear fuel pump.

Show More Show Less


Fuel Pump Lock Ring
2X Entries Into Our F80 M3 Sweepstakes
URO - Corporate Logo
T#:8741229
Part#: 16117188565
Ships in 1 Business Day
$ 18.19 USD
Free Shipping on orders $49 and up
$ 18.19 USD
Free Shipping on orders $49 and up
Fuel Filter/Fuel Pressure Regulator Gasket
2X Entries Into Our F80 M3 Sweepstakes
URO - Corporate Logo
T#:591937
Part#: 16116765055
Ships in 1 Business Day
$ 17.99

This product was last offered at the strikethrough price on
08-13-2026

$ 15.99 USD
Free Shipping on orders $49 and up
$ 15.99 USD
Free Shipping on orders $49 and up
Stop fuel leaks with a replacement seal