Select Vehicle
BMW
Mini
Purpose
Category
-
Coilover Systems
Create an account to be able to build Wish Lists.
The B16 PSS9 coilovers offer a stiffer spring rate than stock and a lower ride height for less bodyroll and better handling. These are among the easiest coil over kits on the market - no special mounts required (works with stock mounts and sway bar links), larger adjustment knob allows for easy shock damping changes, and coil over spanner wrenches included for easy height changes. Bilstein backs up their technology with a limited lifetime warranty. TUV approved for fitment, safety, and quality!
Bilstein's monotube shock dampers in the PSS9 offer 9 precise settings for compression and rebound. A new setting is just a click away, allowing you to set a ride and handling combination that works for your setting. Instead of offering too many shock settings that you're never going to use, Bilstein has chosen ten optimal damping curves from a smooth street setting (P9) to an ultra-stiff track-only setup (P1). Shock changes are made from an easy-to-use over-sized adjuster knob.
Ride height adjustments are done from perches that ride on each shock body, which are zinc coated for excellent wear and corrosion resistance. You can set the ride height between 0.5 to 1.3 inches lower than stock ride height. Springs are progressively rated so their initial compression rating is quite soft and then becomes stiffer as the spring compresses. These are stiffer than most coil over kit manufacturers and the results of Bilstein's extensive testing on the German Nurgburgring and Autobahn.
The fitment of these is just like a standard shock and spring package. The front struts and rear shocks are compatible with the stock strut and shock mounts. You can re-use your own or choose a mount with additional features. Because the Bilstein design keeps the sway bar tab in the original location, you can re-use the stock sway bar links. Using the stock mounts keeps the cost and complexity down and allows for TUV certification. You can also be assured of the stock mount's quiet and long-lasting performance. The assembly of the front strut is the same as a the factory strut. In the rear, ride height is made by an adjustable spring perch that sits under the rear spring. Install instructions and diagrams included.
If you're looking for a supremely capable and high quality suspension, then look no further than the Bilstein PSS9. It combines all of the best German engineering with real-world development, and a lifetime warranty.
Fitment note: this system works only on cars not equipped with the factory EDC electronically adjustable shocks.
Featuring:
This Bilstein PSS9 coilover kit fits the following BMWs:
2004-2005 E63 645Ci coupe
2004-2005 E64 645Ci convertibe
2006-2010 E63 650i coupe
2006-2010 E64 650i convertible
State-of-the-art technology from motor sports for more performance on the road for your E36 M3. The separate and independently adjustable rebound- and compression damping allows for an individual suspension setup for different uses and preferences. The unique patented system with its two-stage valves allows a rebound damping adjustment (comfort) and a compression adjustment (driving dynamics) in the low-speed range while the high-speed range which controls the driving safety, is fixed.
When using original tires, wheel offset spacers may be required.
MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.
MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.
The H&R Coil Over kit takes the traditional shock/spring package one step further. H&R combines their progressive-rate springs with specially valved shocks and adds height adjusters that let you set the ride height to your own personal tastes. These coil overs are designed for street use with progressive rate springs that start out soft and stiffen as they are compressed. This helps to keep the ride compliant while still giving better handling and balance.
H&R designs each suspension to work as a coil over. This means that the correct amount of travel has been built into each shock. And the shocks are valved specifically for the spring rates to give a tight and controlled ride without being harsh or ultra-stiff. Each H&R coil over is TUV tested and approved and meets ISO quality standards. These are used with the stock strut and shock mounts for a quick and easy install.
SPECIAL PRICING FOR A VERY LIMITED TIME!
FREE GROUND SHIPPING
Height adjustment range:
F: -1.0-2.5"
R: -1.0-2.0"
This coilover kit fits the following BMWs:
6/1992-1998 E36 BMW 318i 318is
Upgrade your Mini's suspension system with the BC Racing BR Series Coilover Suspension Kit, engineered for exceptional street and track performance. These coilovers are compatible with the Dynamic Damper Control (DDC) system, offering 30 levels of simultaneous compression and rebound dampening adjustments. Featuring a 2-inch minimum ride height drop, they are ideal for both track and street driving conditions. Constructed with high-grade materials like 6061-T6 Aluminum, STKM13C steel, and SAE9254 steel springs, these coilovers ensure durability, reliability, and corrosion resistance. With 6k front and 5k rear spring rates and V-Barrel springs, these coilovers guarantee optimal performance and a perfect fit for your Mini.
MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.
MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.
MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.
MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.
Looking for coilovers that will provide reliability on street driven vehicles but are also capable of feeding your weekend track demon's desire for performance? BC Racing's BR Series coilover kit may be just the thing for you.
BR Series coilovers are the most popular and versatile option offered by BC racing, offering features such as 30-level dampening adjustment (simultaneous compression and rebound control), linear springs where possible, and a minimum of 2 inches ride height drop. To ensure performance, comfort, and quality, all BR Series kits are Dyno tested during the design stage to determine the best valving and spring rates, then installed and tested for a minimum of 6 months. This kit features mounts and brackets that are fully compatible with all stock mounting points and components.
The upper shock/strut mounts are all constructed of 6061-T6 Aluminum for strength and weight savings. BC Racing design 1 of 3 types of upper mounts for each vehicle: Caster/Camber Plates (+/- 3* camber), Camber Plates (+/- 3* camber), and Rubber Mount Plates (NVH reduction). The included mount option for this kit is shown in the kit specs and features below.
Lower shock mounts are powder coated for corrosion protection and constructed of either 6061-T6 aluminum that has been milled from a single piece (fork or bolt eye mount) or of STKM13C steel with all brackets welded robotically.
The included springs come in one of 3 styles: linear, S-barrel, and V-barrel. Linear springs are used in most applications unless limited by the OE design that does not allow the use of linear springs. All spring options are made from SAE9254 steel and have a zinc coating applied under the powder coating for increased spring corrosion protection and long term reliability.
All shock bodies used in the BR Series coilovers use a 53mm shock body (unless noted otherwise) for added strength, performance, and increased fluid capacity. All shocks are then powder coated black chrome for clean styling and corrosion protection.
Specs and Features:
MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.
MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.
The H&R Coil Over kit takes the traditional shock/spring package one step further. H&R combines their progressive-rate springs with specially valved shocks and adds height adjusters that let you set the ride height to your own personal tastes. These coil overs are designed for street use with progressive rate springs that start out soft and stiffen as they are compressed. This helps to keep the ride compliant while still giving better handling and balance.
H&R designs each suspension to work as a coil over. This means that the correct amount of travel has been built into each shock. And the shocks are valved specifically for the spring rates to give a tight and controlled ride without being harsh or ultra-stiff. Each H&R coil over is TUV tested and approved and meets ISO quality standards. These are
SPECIAL PRICING FOR A VERY LIMITED TIME!
FREE GROUND SHIPPING
used with the stock strut and shock mounts for a quick and easy install.
Height adjustment range:
F: -1.25-2.5"
R: -.75-2.0"
SPECIAL PRICING FOR A VERY LIMITED TIME!
This coilover kit fits the following BMWs:
2006-2011 E90 BMW 325i 328i 330i 335d 335i - Sedan
2007-2012 E92 BMW 328i 335i 335is - Coupe
2007-2012 E93 BMW 328i 335i - Convertible
Bilstein has teamed up with Eibach to offer matched shock and spring packages. These Eibach springs are mated to a special set of Bilstein shocks to deliver a sporty and taut ride with as little impact on ride comfort as possible.
The Sportline kit uses an Eibach Sportline spring with Bilstein's Sport shocks and struts. Instead of taking parts from different manufacturers, Bilstein has tested the performance of the Eibach spring and tailored their shocks to be a true match for the new spring rate and ride height. This is known as a matched shock and spring and very few tuning companies take these extra steps. Eibach Sportline springs are more aggressive than Pro-Kit springs, which tend to be softer overall than most other aftermarket springs, but still ensures ride quality stays close to stock comfort while still giving you a much more aggressive lowered stance and significantly improved handling.
Bilstein B12 Features:
Most cars don't need coil overs to improve their handling and bodyroll. For most drivers, simply replacing the shocks and springs with performance versions will meet their goals. If your shocks need replacing, and you felt the handling could be improved a little bit, this is an excellent performance suspension for you.
This item fits the following BMWs:
2004-2010 E60 BMW 545i 550i
This product was last offered at the strikethrough price on
07-01-2026
This product was last offered at the strikethrough price on
07-01-2026
Looking for coilovers that will provide reliability on street driven vehicles but are also capable of feeding your weekend track demon's desire for performance? BC Racing's BR Series coilover kit may be just the thing for you.
BR Series coilovers are the most popular and versatile option offered by BC racing, offering features such as 30-level dampening adjustment (simultaneous compression and rebound control), linear springs where possible, and a minimum of 2 inches ride height drop. To ensure performance, comfort, and quality, all BR Series kits are Dyno tested during the design stage to determine the best valving and spring rates, then installed and tested for a minimum of 6 months. This kit features mounts and brackets that are fully compatible with all stock mounting points and components.
The upper shock/strut mounts are all constructed of 6061-T6 Aluminum for strength and weight savings. BC Racing design 1 of 3 types of upper mounts for each vehicle: Caster/Camber Plates (+/- 3* camber), Camber Plates (+/- 3* camber), and Rubber Mount Plates (NVH reduction). The included mount option for this kit is shown in the kit specs and features below.
Lower shock mounts are powder coated for corrosion protection and constructed of either 6061-T6 aluminum that has been milled from a single piece (fork or bolt eye mount) or of STKM13C steel with all brackets welded robotically.
The included springs come in one of 3 styles: linear, S-barrel, and V-barrel. Linear springs are used in most applications unless limited by the OE design that does not allow the use of linear springs. All spring options are made from SAE9254 steel and have a zinc coating applied under the powder coating for increased spring corrosion protection and long term reliability.
All shock bodies used in the BR Series coilovers use a 53mm shock body (unless noted otherwise) for added strength, performance, and increased fluid capacity. All shocks are then powder coated black chrome for clean styling and corrosion protection.
Specs and Features: