BMW Cooling System Parts & Accessories

The N20/n26 engined cars already suffer from reduced cooling area because of the factory intercooler, tight space under the hood, and of course heat from the turbo(s). BMW addressed these challenges a number of ways, including a dynamic, 'smart' electric water pump with increased output compared to normally aspirated models. The cooling demands mean additional stress on the major cooling components, especially the water pump and thermostat. 
 

Kit includes:

• Mahle-Behr thermostat
• Pierburg water pump
• Genuine BMW coolant
• Mounting hardware required for both the thermostat and water pump

This item fits the following BMWs: 
2014+ F22 BMW 228i 228i xDrive 
2014+ F23 BMW 228i 228i xDrive 
2012+ F30 BMW 328i 328i xDrive - Sedan 
2013+ F31 BMW 328i xDrive - Wagon 
2013+ F32 BMW 428i 428i xDrive - Coupe 
2013+ F33 BMW 428i Convertible 428i xDrive Convertible - Convertible 
2014+ F34 BMW 328i xDrive GT - Gran Tourismo 
2014+ F36 BMW 428i Gran Coupe 428i xDrive Gran Coupe 
2012+ F10 BMW 528i 528i xDrive 
2011+ F25 BMW X3 xDrive28i 
2015+ F26 BMW X4 xDrive28i 
2009+ E89 BMW Z4 sDrive28i

If your vehicle is experiencing cooling issues, chances are the thermostat is the cause. Common symptoms include prolonged warm-up at highway speeds from the thermostat being stuck open, or consistent overheating issues from the thermostat being stuck in the closed position. Either condition can result in poor performance, and potential damage to vital components in your vehicle.

Kit includes

• Wahler Thermostat
• 1 liter of Coolant

This item fits the following BMWs: 
2008-2013  E82 BMW  135i 135is 1M Coupe 
2013+  E84 BMW  X1 xDrive35i 
2011  E90 BMW  335i 335xi 335i xDrive - Sedan 
2011-2013  E92 BMW  335i 335xi 335i xDrive - Coupe 
2011-2013  E93 BMW  335i Convertible 
2011-2013  E70 BMW  X5 xDrive35i 
2011-2013  E71 BMW  X6 xDrive35i

The water pumps in BMW N54 models are known for failure near 80,000 miles. This is a very common issue that often times leaves the owner stranded. This kit provides a single stop for the water pump and thermostat replacement to save the search and get you back on the road.

Included in this kit:

Thermostat
Water pump
Genuine BMW coolant
Mounting hardware required for both the thermostat and water pump

The water pumps in BMW's should be serviced near 80,000 miles and may become an issue often times leaving the owner stranded. The aftermarket kit offered provides a single stop for water pump and thermostat replacement needs to save the search and get you back on the road.

Kit includes:

• Thermostat
• Water pump
• Coolant

This item fits the following BMW Engines: 
N63,N63N,S63,N62N 

Just like the rest of your vehicle's major systems, the cooling system must also be addressed periodically to ensure proper cooling and component reliability. Plastic and rubber components become brittle and prone to splitting or cracking after long periods of heating and cooling cycles, especially in colder climates! The coolant itself can degrade or become contaminated, leading to potential corrosion or freezing issues. Finally, thermostats and sensors can fail completely, preventing proper cooling and/or coolant temperature readings to become inaccurate.

To make sure you are not left stranded on the side of the road with an overheated engine, we have put together this Basic Cooling System Service kit. This kit contains all of the most-likely-to-fail components, giving you peace of mind knowing your engine will continue to run cool for another 60,000+ miles.

See kit contents below for all included components.

Just like the rest of your vehicle's major systems, the cooling system must also be addressed periodically to ensure proper cooling and component reliability. Plastic and rubber components become brittle and prone to splitting or cracking after long periods of heating and cooling cycles, especially in colder climates! The coolant itself can degrade or become contaminated, leading to potential corrosion or freezing issues. Finally, thermostats and sensors can fail completely, preventing proper cooling and/or coolant temperature readings to become inaccurate.

To make sure you are not left stranded on the side of the road with an overheated engine, we have put together this Basic Cooling System Service kit. This kit contains all of the most-likely-to-fail components, giving you peace of mind knowing your engine will continue to run cool for another 60,000+ miles.

See kit contents below for all included components.

If you plan to drive your BMW aggressively on the track, it is important that you upgrade your cooling system to avoid overheating. To ensure your BMW keeps cool on the track, we have built out our new High Performance Cooling System Upgrade kits. Featured in this kit is everything you will need to redo your cooling system from top to bottom with OEM components, with select stock components swapped out for the high performance alternative! This kit includes a high performance Mishimoto Radiator, for significantly better cooling than the stock radiator and full aluminum construction that won't crack from long term heat cycling, a performance Mishimoto 70*C thermostat, for lower temperature operation and increased cooling of the engine, and a Stewart High Performance Water Pump, for dramatically increased coolant flow at all RPMs. 

Additional items included in this kit:

• OEM Replacement Coolant Hoses
• OEM Expansion Tank, Cap, and Level Sensor
• OEM Belts, Tensioners, and Pulleys
• OEM Auxiliary Fan Switch
• Genuine BMW Hardware for Easy Installation
• ECS Tuning Aluminum Water Pump Pulley - For increased reliability over the stock composite pulley

Just like the rest of your vehicle's major systems, the cooling system must also be addressed periodically to ensure proper cooling and component reliability. Plastic and rubber components become brittle and prone to splitting or cracking after long periods of heating and cooling cycles, especially in colder climates! The coolant itself can degrade or become contaminated, leading to potential corrosion or freezing issues. Finally, thermostats and sensors can fail completely, preventing proper cooling and/or coolant temperature readings to become inaccurate.

To make sure you are not left stranded on the side of the road with an overheated engine, we have put together this Basic Cooling System Service kit. This kit contains all of the most-likely-to-fail components, giving you peace of mind knowing your engine will continue to run cool for another 60,000+ miles.

See kit contents below for all included components.

Just like the rest of your vehicle's major systems, the cooling system must also be addressed periodically to ensure proper cooling and component reliability. Plastic and rubber components become brittle and prone to splitting or cracking after long periods of heating and cooling cycles, especially in colder climates! The coolant itself can degrade or become contaminated, leading to potential corrosion or freezing issues. Finally, thermostats and sensors can fail completely, preventing proper cooling and/or coolant temperature readings to become inaccurate.

To make sure you are not left stranded on the side of the road with an overheated engine, we have put together this Basic Cooling System Service kit. This kit contains all of the most-likely-to-fail components, giving you peace of mind knowing your engine will continue to run cool for another 60,000+ miles.

See kit contents below for all included components.

Just like the rest of your vehicle's major systems, the cooling system must also be addressed periodically to ensure proper cooling and component reliability. Plastic and rubber components become brittle and prone to splitting or cracking after long periods of heating and cooling cycles, especially in colder climates! The coolant itself can degrade or become contaminated, leading to potential corrosion or freezing issues. Finally, thermostats and sensors can fail completely, preventing proper cooling and/or coolant temperature readings to become inaccurate.

To make sure you are not left stranded on the side of the road with an overheated engine, we have put together this Basic Cooling System Service kit. This kit contains all of the most-likely-to-fail components, giving you peace of mind knowing your engine will continue to run cool for another 60,000+ miles.

See kit contents below for all included components.

The water pumps in these BMW models are known for failure near 80,000 miles is a very common issue often times leaving the owner stranded. This kit provides a single stop for water pump and thermostat replacement needs to save the search and get you back on the road.

Kit includes:

• Genuine BMW Thermostat
• OEM VDO Electric Water Pump
• Genuine BMW Auxiliary Water Pump
• Genuine BMW Antifreeze/Coolant
• OEM Mounting hardware required for both the thermostat and water pump

Just like the rest of your vehicle's major systems, the cooling system must also be addressed periodically to ensure proper cooling and component reliability. Plastic and rubber components become brittle and prone to splitting or cracking after long periods of heating and cooling cycles, especially in colder climates! The coolant itself can degrade or become contaminated, leading to potential corrosion or freezing issues. Finally, thermostats and sensors can fail completely, preventing proper cooling and/or coolant temperature readings to become inaccurate.

To make sure you are not left stranded on the side of the road with an overheated engine, we have put together this Basic Cooling System Service kit. This kit contains all of the most-likely-to-fail components, giving you peace of mind knowing your engine will continue to run cool for another 60,000+ miles.

See kit contents below for all included components.

When it comes time to replace your thermostat, be sure you have everything you need. This kit includes everything you need to replace your thermostat, including the thermostat.

Kit includes:

• Thermostat with gasket
• Thermostat mounting hardware
• 1 liter of coolant

This waterpump fits the following BMWs: 
1992-1999 E36 3 series - 323is, 323ic, 325i, 325is, 325ic, 328i, 328ic, M3 3.0 (S50/US), M3 3.2 (S52) 

If you plan to drive your BMW aggressively on the track, it is important that you upgrade your cooling system to avoid overheating. To ensure your BMW keeps cool on the track, we have built out our new High Performance Cooling System Upgrade kits. Featured in this kit is everything you will need to redo your cooling system from top to bottom with OEM components, with select stock components swapped out for the high performance alternative! This kit includes a high performance ECS Tuning Aluminum Radiator, for significantly better cooling than the stock radiator and full aluminum construction that won't crack from long term heat cycling, a performance Mishimoto 68*C thermostat, for lower temperature operation and increased cooling of the engine, and a Stewart High Performance Water Pump, for dramatically increased coolant flow at all RPMs. 

Additional items included in this kit:

• ECS Tuning Silicone Coolant Hoses - For increased reliability over the stock rubber hoses
• ECS Tuning Heavy Duty Aluminum Coolant Bleeder Screw
• OEM Expansion Tank, Cap, and Level Sensor
• OEM Belts, Tensioners, and Pulleys
• OEM Low Temperature Auxiliary Fan Switch
• Genuine BMW Hardware for Easy Installation
• ECS Tuning Aluminum Water Pump Pulley - For increased coolant flow and reliability over the stock composite pulley

The fan that attaches to the water pump carries so much rotational mass that it can actually hinder the performance of your engine. To address this, we now offer out line of fan delete kits that replace everything needed to get rid of your fan and fan clutch, without causing cooling issues as a result. This basic kit is the cheapest option, including just the bare essentials to get the job done and get your car running without a fan.

This kit is best for someone who has already upgraded their thermostat housing and/or water pump pulley and has performed regular maintenance on their engine drive belts.

Included in this kit:

• 80* thermostat
• 1 liter of coolant
• Water Wetter coolant additive
• Low-temperature coolant temperature sensor/switch

Fits the following BMWs:
1992-09/1995 E36 BMW 325i/is/ic 328i/is/ic M3

**This kit is intended to be used with cars that have a functional auxiliary fan (64508364093) or an upgraded electrical fan installed.**

The fan that attaches to the water pump carries so much rotational mass that it can actually hinder the performance of your engine. To address this, we now offer out line of fan delete kits that replace everything needed to get rid of your fan and fan clutch, without causing cooling issues as a result. This Ultimate kit is the top tier option, including the essential conversion components, the upgraded aluminum thermostat housing, and a brand new accessory belt.

This kit is best for someone who has not performed recent cooling system maintenance or who wants to replace everything at once for increased reliability and longevity.

Included in this kit:

• 80* thermostat
• 1 liter of coolant
• Water Wetter coolant additive
• Low-temperature coolant temperature sensor/switch
• Aluminum thermostat housing with gaskets
• Fan delete nut
• ECS  Aluminum Water Pump Pulley - Black
• Accessory Belt

Fits the following BMWs:
09/1995-1999 E36 BMW 323is/ic 328i/is/ic M3

**This kit is intended to be used with cars that have a functional auxiliary fan (64508364093) or an upgraded electrical fan installed.**

If you plan to drive your BMW aggressively on the track, it is important that you upgrade your cooling system to avoid overheating. To ensure your BMW keeps cool on the track, we have built out our new High Performance Cooling System Upgrade kits. Featured in this kit is everything you will need to redo your cooling system from top to bottom with OEM components, with select stock components swapped out for the high performance alternative! This kit includes a high performance Mishimoto Radiator for significantly better cooling than the stock radiator and full aluminum construction that won't crack from long term heat cycling, and a Genuine BMW Motorsport 55*C thermostat, for lower temperature operation and increased cooling of the engine. 

Additional items included in this kit:

• ECS Tuning Silicone Replacement Coolant Hoses - For increased reliability over stock rubber hoses
• ECS Tuning Heavy Duty Aluminum Bleeder Screw
• OEM Expansion Tank, Cap, and Level Sensor
• OEM Belts, Tensioners, and Pulleys
• OEM Auxiliary Fan Switch
• Genuine BMW Hardware for Easy Installation
• ECS Tuning Aluminum Water Pump Pulley - For increased reliability over the stock composite pulley

Looking to improve your cooling system's performance and add some peace of mind at the same time? Look no further. This kit includes everything you need to add performance, durability and longevity to your cooling system without spending a ton of money. Best of all, the upgrade can be performed by a reasonably competent DIY enthusiast in an afternoon. The team at ECS Tuning supplies their excellent silicone radiator hoses, stainless hose clamps, and aluminum coolant bleed screw for increased durability and heat resistance. Meanwhile, a lower pressure expansion tank cap makes for a less costly "weak link" if the system builds too much pressure, potentially saving you from a costly radiator replacement that could leave you stranded. The kit also includes a gallon of Genuine BMW coolant along with 12 ounces of Red Line Water Wetter, which lowers operating temperatures and protects your cooling system from internal corrosion. All you need is this kit, a few hours of free time, and a gallon of distilled water to keep your E36 cool & running at its best!

Kit Contents:

- ECS Tuning Silicone Radiator Hoses

- ECS Tuning Stainless Steel Hose Clamps

- ECS Tuning Heavy Duty Aluminum Coolant Bleeder Screw

- 1.4 Bar Expansion Tank Cap

- Red Line Water Wetter - 12oz

- Genuine BMW Coolant - 1 Gallon

Fits the Following BMWs:

E36 323i 325i 328i M3