BMW Suspension Bushings & Mounts

For all 2001 to 2005 325xi and 330xi. For convenience, we have assembled this bushing carrier bracket kit, to save you time when changing our control arm bushings. It includes two bushing carriers with pre-installed bushings (one left, one right) and mounting bolts.

 These bushing brackets fit all 2001, 2002, 2003, 2004, and 2005 model BMW 325xi and 330xi.

Swapping in E46 control arms into your E30 or E36 significantly increases negative camber by widening the track width and also gives you more clearance for more steering angle. Condor's CNC machined control arm brackets are made from solid steel and are fitted with a solid hex-shaped bushing. Designed for the street or the track, they hold the control arm steady and eliminate "shimmy" caused by stock bushings. They sharpen steering and improve overall driving feel. Comparable to the NLA Treehouse E36 & E30 Eyeball Arms.

Easiest install of any aftermarket solution
Allow clearance for E30 M50 Conversion exhaust
Street Approved, marginal increase in NVH
Easy Installation, no need for a press
CNC machined steel construction
Solid design without the maintenance of spherical bearings
Heavy-Duty replaceable UHMW insert. Don't be misinformed, UHMW is the best material for these inserts. Delrin is not self-lubricating and will crack and degrade over time.
Powder coated white for corrosion resistance
Improve caster with M3 offset geometry
Keep proper steering geometry under high loads
Made in the U.S.A.
Fitment:
E30 84-91 3 Series
E36 92-98 3 series & Z3

Note that you will need to use E36 outer tie rods and E90 inner tie rods when installing in an E30 or E36

Be sure to measure your control arms to determine if you need 21mm or 23mm. Meyle makes a standard e46 control arm and a Heavy Duty control arm. Most HD arms have a hex that is larger in size (23mm). Lifetime Warranty

Swapping in E46 control arms into your E30 or E36 will significantly increase negative camber by widening the track width and will also give you more clearance for more steering angle. Condor's conversion bushings are machined from UHMW due to its high rigidity and low coefficient of friction allowing for minimal suspension bushing deflection (geometry change). They've designed them offset to re-center the wheel and give your e30/e36 the correct caster. They will include a stainless-steel insert that tightly presses over the hex pattern on the E46 control arms. You do not need to grind down your control arms or make any other modifications to your chassis. Please note that you will need to use E36 outer tie rods and E90 inner tie rods when installing in an E30 or E36.

Fitment:
Fits the following Meyle and Lemforder arms with 21-22MM Hex.

LEMFORDER ZHP - 31122282121 & 31122282122
LEMFORDER - 31126777851 & 31126777852
MEYLE HD - 31126777851 & 31126777852
*Please note that Meyle makes a standard e46 control arm and a Heavy Duty control arm. SOME HD arms have a hex that is larger in size. These HD control arms may need to be shaved 1-2 mm for proper fitment.

This package of OEM E82 E90 E92 diff mounts replaces the stock rubber diff bushings. On a tuned 335i you may have noticed more driveline shudder or problems hooking up during hard launches. What happens is the stock rubber bushings are under constant flex as engine torque is transmitted through the differential. Under normal driving with a stock car the bushings are rarely stressed. But factor in significant additional torque from a tuned N54/N55 and the stock rubber will quickly show its weaknesses. You may have even broken a diff bolt or two as the heavy differential shifts around. Even non-turbo E82 and E9X models may benefit from fresh bushings.

This is a set of stock rubber bushings, made by OEM supplier Lemforder. They are the same as the Genuine BMW E9X diff mount bushings, but without the more expensive branding. If you're turned off by potential side effects of urethane or Delrin then the OEM diff mounts are your best option. The OEM mounts fit and perform just like the originals so there is no second guessing their quality. If you're looking for an upgrade we offer E9X solid Delrin and aluminum diff mounts that work well, even in street applications.

E9X Diff Mount Set includes:

• 33176760287 x 2, front differential mount
• 33176770866 x 1, rear differential mount
• (new hardware is optional and can be ordered separately below)
  
  This item fits the following BMWs:
  2008-2012 E82 BMW 128i 135i
  2006-2011 E90 BMW 325i 325xi 328i 328xi 328i xDrive 330i 330xi 335d 335i 335xi 335i xDrive - Sedan
  2006-2012 E91 BMW 325xi 328i 328xi 328i xDrive - Wagon
  2007-2013 E92 BMW 328i 328xi 328i xDrive 335i 335is 335xi 335i xDrive - Coupe
  2007-2013 E93 BMW 328i 335i - Convertible

This kit includes Turner Motorsport solid aluminum differential race mounts pre installed in the differential cover for a quick install. These mounts where developed by Turner Motorsport for their Grand-Am Cup E46 M3 race cars, the advantages of solid aluminum mounts is increased suspension & drivetrain response, less drivetrain loss resulting in more wheel horsepower, and longevity - they effectively last forever. These CNC-machined mounts are a direct replacement for the stock rubber pieces, and have been lightened to remove excess weight.