BMW Internal Engine Parts

BMW S65 BE Bearings Connecting Rod Bearing Upgrade Set is designed to address the known flaws in the factory BMW rod bearings, particularly for the S65B40 engine. Manufactured by Clevite to BE Bearing specifications, this set provides a crucial upgrade with its enhanced materials and design, ensuring improved performance and durability.

The original BMW bearings have minimal clearance, which leads to premature wear and potential engine failure. This upgrade replaces the tin-aluminum factory bearings with a superior silver-oxide-coated tri-metal "F" series design. The new bearings can handle 30% more load, offer better performance in low oil conditions, and are more forgiving of foreign particles in the oil. Designed specifically for BMW S65 engines, these bearings provide optimal performance for high-horsepower applications.

• Designed specifically for BMW S65B40 engines
• Silver-oxide coating withstands 30% more load capacity
• Improved performance under low-oil and boundary conditions
• Stronger backing material for enhanced durability
• Corrects factory BMW rod bearing clearance issue
• Ideal for high-horsepower applications and factory 10W60 weight oils
• Complete set for 8 cylinders, ready for installation

Fits the following BMWs:

• 2008-2013 E9X BMW M3 (S65)

Designed and manufactured by Clevite to BE Bearing specifications.

These bearings replace the factory BMW rod bearings. The original BMW bearings have too little clearance, which leads to premature bearing wear and can cause early engine failure.  Furthermore, the factory BMW bearings are made from tin-aluminum which are 5-times harder than a softer lead-copper bearing design. A softer bearing is better for your engine and more tolerant of foreign particles suspended in your oil.

These BE Bearings feature a state-of-the-art Clevite Tri-Metal design with the Clevite Tri-Armor(tm) coating.

• Lead-copper design for greater durability and easy tracking with oil analysis like Blackstone (recommended).
• Designed with extra clearance to "fix" the BMW rod bearing design flaw.
• Designed for use with factory 10W60 weight oils.
• Tri-Armor coated for low conditions during cold start
• Ideal for start-stop vehicles
• Applicable for BMW engines S85B50
• Standard Clearance
• Sold as complete set (10-cylinders)

Fits the following BMWs:
2005-2010 E60 BMW M5
2005-2010 E63/64 BMW M6

Designed by BE Bearings, manufactured by ARP.  These custom made rod bolts are designed to be used on BMW factory connecting rods.  BE Bearings worked with ARP to come up with custom rod bolt torque specifications to ensure minimal rod big end bore distortion.  Their bolts have been measured and verified to guarantee minimal bore distortion, and stay within the ARP torque specification.

Technical Details:

• Composition:   ARP2000®
• Yield strength:   200,000 PSI
• Tensile strength:   220,000 PSI
• Torque specification:   50 Ft/Lbs, or 0.0065-0.0070 inch stretch

Fits the following BMWs:
2005-2010 E60 BMW M5
2005-2010 E63/64 BMW M6

Often called main bearings, crankshaft bearing shells sit between the rotating assembly and the engine block. They allow the crankshaft to rotate freely, but are prone to wear from deterioration and lack of lubrication.

This complete set consists of nine bearings, enough to fill each journal.

If you're overhauling your M10, choose Hella crankshaft-bearing shells for a lasting solution.

For the US E36 M3. Schrick 264/256 degree camshafts boost mid-high end power for that extra motivation at higher rpm. Low-end torque is not seriously affected due to the M50/M52s VAN0S System. And, higher profile cams work extremely well with an upgraded intake and exhaust. When upgrading the cams there are other areas you must take into consideration. Higher-flow fuel injectors, larger mass-air sensor, and custom programming are strongly recommended. Turner Motorsport sells complete intake & cam packages that boost power to over 290hp. See the Engine section under Camshafts for more info.

Cam Specs:
Intake - 264 degree, 11.2mm lift
Exhaust - 256 degree, 10.6mm lift

Schrick Technical Information / Specs

This item fits the following BMWs:
1993-1998 E36 BMW 325i 325is 325ic 328i 328is 328ic M3
1993-1995 E34 BMW 525i
1997-1998 Z3 BMW Z3 2.8
1998-1999 Z3 BMW M Roadster M Coupe