VTT S55 Crank Bolt Capture - F8X S55 F3x N55

T#:557934

Part#: VTT-S55-CBC

In Stock

$ 129.99 USD

Add to Wish List

Qty

$ 129.99 USD

Add to Wish List

The S55 suffers from a weak point in its crankshaft. It has been reported that when increasing the power to the engine, the crank hub can move or spin slightly under an extreme load.

E46 M3 Schrick DLC-Coated Rocker Arm

T#:342372

Part#: 041513800

In Stock

$ 263.99

This product was last offered at the strikethrough price on
07-07-2026

$ 165.00 USD

Add to Wish List

Qty

$ 165.00 USD

Add to Wish List

The roller rocker arms transfer the rotational force of the camshaft to open the intake and exhaust valves. One end is raised and lowered by the rotating lobe of the camshaft, while the other end acts on the associated valve stem. If a roller rocker arm has failed you may experience a constant ticking noise during engine operation, or alternatively if the rocker arm has broken, you will receive multiple misfires and a rough running engine.

Show More Show Less

Vargas "Spline Lock" Crank Hub Solution - Includes Crank Bolt Capture...

T#:558795

Part#: VTT-CRANKHUB-1

In Stock

$ 889.99 USD

Add to Wish List

Qty

$ 889.99 USD

Add to Wish List

Under certain conditions, the N55 crank hub likes to spin, without warning and even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines which press into the crank, and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and ECS are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution.

Show More Show Less

Bav Auto Crankshaft Front Oil Seal Removal / Installer Tool - N54, N5...

T#:580444

Part#: B8800139

Ships on Sep 1, 2026

Sale - Save 5% $ 203.99

This product was last offered at the strikethrough price on
05-03-2026

$ 193.79 USD

Add to Wish List

Qty

Sale - Save 5%

$ 203.99

This product was last offered at the strikethrough price on
05-03-2026

$ 193.79 USD

Add to Wish List

Used in removal and installation of the front crankshaft seal on BMW N55 engines, a common job that you can save yourself a ton of money doing at home.

Spline Lock Crank Hub Solution W/ Complete Package - N55 S55 ...

T#:18733532

Part#: VTT-CRANKHUB-6

Ships in 1 Business Day

$ 986.99

This product was last offered at the strikethrough price on
06-28-2026

$ 939.99 USD

Add to Wish List

Qty

$ 939.99 USD

Add to Wish List

Under certain conditions, the N55 crank hub likes to spin, without warning and even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines which press into the crank, and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and ECS are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution.

Show More Show Less

ECS M62TU Vanos Seal Rebuild Kit - E39, E38, E53

T#:396674

Part#: 017301ECS01

In Stock

Sale - Save 25% $ 67.99

This product was last offered at the strikethrough price on
06-13-2026

$ 50.99 USD

Add to Wish List

Qty

Sale - Save 25%

$ 67.99

This product was last offered at the strikethrough price on
06-13-2026

$ 50.99 USD

Add to Wish List

If you're not sure if your Vanos seals are bad then the only question you need to answer is if you've replaced them. Every unit from the factory came with the same failure prone o-rings and seals, even the re-manufactured units you can still get today. The only real fix is by replacing the seals and o-rings with material that is built to last in the oiled, extreme temperature environment found in these kits.

A premium product replacement with easy to follow instructions makes rebuilding your Vanos unit a must. Even thought the power loss is barely felt it's the opposite result once you replace the seals, every car that gets rebuilt ends up wowing the customer and all of them saying they didn't realize what they lost.

There are a number of symptoms that will plague your car as a result of these failing seals such as erratic idle, engine hesitation, stalling, and increased fuel consumption to name a few. If you've been chasing down any of these symptoms with no fix then this could be your issue.

Show More Show Less

WPC Treated Rod Bearing Set - M42, M44, M20, M50, M52, S50, S52, M54 ...

T#:395066

Part#: 11241284849WPC

In Stock

Sale - Save 25% $ 188.99

This product was last offered at the strikethrough price on
06-13-2026

$ 141.74 USD

Add to Wish List

Qty

Sale - Save 25%

$ 188.99

This product was last offered at the strikethrough price on
06-13-2026

$ 141.74 USD

Add to Wish List

These WPC-treated bearings are the best we have seen! WPC is a shot-peening treatment at a microscopic level. It's perfect for sensitive surfaces like bearings. The WPC treatment removes imperfections and high spots, while creating a surface that retains oil better than the original surface. This greatly reduces friction. The bearings in this kit are original equipment KS bearings that are sent to WPC for treatment. The treated bearings are stronger with less metal fatigue and less friction than buying off-the-shelf bearings from the dealer.

This item fits the following BMWs:
1984-1991 E30 BMW 318i 318is 318ic 325e 325es 325i 325ic 325is 325ix
1992-1998 E36 BMW 318i 318is 318ti 318ic 323is 323ic 325i 325is 325ic 328i 328is 328ic M3
1999-2005 E46 BMW 323i 323ci 325i 325ci 325xi 328i 328ci 330i 330ci 330xi
1982-1988 E28 BMW 528e
1989-1995 E34 BMW 525i
1997-2003 E39 BMW 525i 528i 530i
2004-2005 E60 BMW 525i 530i
2004-2006 E83 BMW X3 2.5i X3 3.0i
2000-2006 E53 BMW X5 3.0i
1997-2002 Z3 BMW Z3 1.9 Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i M Roadster M Coupe
2003-2005 Z4 BMW Z4 2.5i Z4 3.0i

Show More Show Less

Timing Chain - Upper

T#:17871154

Part#: 11311432177

In Stock

Sale - Save 20% $ 27.99

This product was last offered at the strikethrough price on
05-03-2026

$ 22.39 USD

Add to Wish List

Qty

Sale - Save 20%

$ 27.99

This product was last offered at the strikethrough price on
05-03-2026

$ 22.39 USD

Add to Wish List

VAC Performance Coated Rod Bearing Kit - Standard Size - S65 ...

T#:1061445

Part#: VAC-HPRBK-S65

In Stock

$ 799.99 USD

Add to Wish List

Qty

$ 799.99 USD

Add to Wish List

VAC's S65 bearings are embraced by BMW engine builders world wide. Popular for both forced induction and N/A builds, their coated bearings are "friction resistant" making thermal breakdowns that can occur due to lack of lubrication a much less common occurrence. Helping to prevent premature engine failures on street cars, and spun bearings under stress at the track when things are most critical.

Show More Show Less

Bav Auto Crankshaft Rear Oil Seal Removal / Installer Tool - N51, N52...

T#:580412

Part#: B8800104

In Stock

Sale - Save 5% $ 147.99

This product was last offered at the strikethrough price on
05-03-2026

$ 140.59 USD

Add to Wish List

Qty

Sale - Save 5%

$ 147.99

This product was last offered at the strikethrough price on
05-03-2026

$ 140.59 USD

Add to Wish List

For removal and installation of the rear crankshaft seal on BMW N51, N52 and N54 engines.

Bav Auto Intermediate Lever Valve Spring Compressor - N20/26 N55 ...

T#:580431

Part#: B8800124

Ships on Sep 1, 2026

Sale - Save 15% $ 178.99

This product was last offered at the strikethrough price on
05-03-2026

$ 152.14 USD

Add to Wish List

Qty

Sale - Save 15%

$ 178.99

This product was last offered at the strikethrough price on
05-03-2026

$ 152.14 USD

Add to Wish List

For installation and removal of pressure springs on intermediate levers of valve train. Ensures quick, easy and safe handling of these high force springs.

Timing Component

T#:17871158

Part#: 11367583208

In Stock

Sale - Save 20% $ 199.99

This product was last offered at the strikethrough price on
05-03-2026

$ 159.99 USD

Add to Wish List

Qty

Sale - Save 20%

$ 199.99

This product was last offered at the strikethrough price on
05-03-2026

$ 159.99 USD

Add to Wish List

ARP Performance Head Stud Kit - N54

T#:1061441

Part#: ARP-HSK-N54

Ships in 7 Business Days

$ 554.99 USD

Add to Wish List

Qty

$ 554.99 USD

Add to Wish List

Despite the fact that BMW engineers some of the worlds most revered engines, during number crunching something always has to be a compromise. One item that is always found to be a weak point- the OEM hardware. It is definitely sub-par for real performance use under high stress such as modded engines and track use. We use these fasteners on all of VAC's in-house head builds. Whenever the head is coming off, your switching to forced induction, or if you are simply prepping to drive your car hard; we highly recommend switching to far superior race-grade hardware. These Head Stud Kits greatly improve reliability; helping to eliminate movement of the of the cylinder head and intern, gasket failure caused by inferior OEM head-bolt stretch. This is the #1 cause of premature head gasket failure, especially on boosted or high output engines. Though more expensive than OEM, converting to one of VAC's head studs kits will not only give added strength and reliability when its needed most, but provides the most accurate torque readings because studs don’t “twist” into the block; all clamping forces are on one axis, and there is less force exerted on the normally stressed threads of the block. This increases block and hardware life and typically makes the head easier to properly install to the block, a blessing if your head may have to be removed more than once. Especially in the time crunch of racing, when engines are dissembled frequently, studs make removing and installing the cylinder head on to the block a much easier task. By allowing the studs to act as a guide on to the head, your head slides on and off and also ensures proper alignment of the head and gasket for the same reason. It is similar to converting your wheel-bolts to wheel-studs.

Show More Show Less

Spline N55 S55 Lock Crank Hub Solution W/ Hardware Package

T#:18733531

Part#: VTT-CRANKHUB-5

Ships in 10 Business Days

$ 880.99 USD

Add to Wish List

Qty

$ 880.99 USD

Add to Wish List

Under certain conditions, the N55 crank hub likes to spin, without warning and even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines which press into the crank, and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and ECS are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution.

Show More Show Less

Bavarian Autosport Crankshaft Holding Tool - BMW

T#:580450

Part#: B8800145

In Stock

Sale - Save 15% $ 77.99

This product was last offered at the strikethrough price on
05-03-2026

$ 66.29 USD

Add to Wish List

Qty

Sale - Save 15%

$ 77.99

This product was last offered at the strikethrough price on
05-03-2026

$ 66.29 USD

Add to Wish List

Makes removal of crankshaft hub nut/bolt much easier. A must-have for replacing timing chains, oil pump chains, leaking crankshaft seals and more.

Bav Auto Crankshaft Pulley Holding Tool

T#:580404

Part#: B8800094

In Stock

Sale - Save 10% $ 180.99

This product was last offered at the strikethrough price on
05-03-2026

$ 162.89 USD

Add to Wish List

Qty

Sale - Save 10%

$ 180.99

This product was last offered at the strikethrough price on
05-03-2026

$ 162.89 USD

Add to Wish List

Bav Auto's Crankshaft Pulley Holding Tool enables you to remove your crankshaft nut/bolt with ease - we recommend this tool if you intend on replacing timing chains, oil pump chains, leaking crankshaft seals, etc.

Show More Show Less

BMW S54 VAC Performance Coated Rod Bearing Kit

T#:7164819

Part#: VAC-HPRBS-S54

Ships on Sep 1, 2026

$ 479.99 USD

Add to Wish List

Qty

$ 479.99 USD

Add to Wish List

BMW S54 VAC Performance Coated Rod Bearing Kit is highly regarded by BMW engine builders worldwide for its superior quality and performance. Ideal for both forced induction and naturally aspirated builds, these coated bearings are designed to be friction-resistant, reducing the risk of thermal breakdowns due to inadequate lubrication. This feature significantly decreases the chances of premature engine failure in street cars and minimizes the risk of spun bearings during high-stress track conditions.

The VAC Performance Coated Rod Bearing Kit is proven to help maintain engine reliability, even in situations with reduced oil pressure.

Enhanced Durability: Coated bearings are friction-resistant, reducing the risk of thermal breakdown.
Increased Reliability: Helps prevent premature engine failure and spun bearings under stress.
Versatile Performance: Suitable for both forced induction and naturally aspirated engine builds.
Proven Track Record: Tested by customers to ensure reliable performance even with oil pressure loss.

VAC Tech Notes:

Ensure proper tolerance and size checks before installation.
Professional installation is recommended due to specialized tools required.
Returns are not available on any engine bearings.

Show More Show Less

WPC Treated Crank Bearing Set

T#:585720

Part#: 11211706847WPCKT

In Stock

Sale - Save 3% $ 250.99

This product was last offered at the strikethrough price on
06-14-2026

$ 243.46 USD

Add to Wish List

Qty

Sale - Save 3%

$ 250.99

This product was last offered at the strikethrough price on
06-14-2026

$ 243.46 USD

Add to Wish List

What's better than using new crank bearings in your next engine build? WPC-treated bearings! What is WPC, you ask? WPC is a surface treatment that reduces friction and adds strength - two improvements that benefit internal engine components. Ultra-fine particles are fired at the surface at very high speeds, like shot-peening - but much, much smaller. The parts come out smoother and stronger due to thermal discharge. The two largest enemies of any high-performance engine are heat and friction - and WPC has found a way to reduce both. What are you waiting for? Use WPC-treated bearings on your next engine build or crank service!

Show More Show Less

BMW N54 ARP Head Stud Kit

T#:17538610

Part#: ARP-HSK-N54-14

In Stock

$ 599.99 USD

Add to Wish List

Qty

$ 599.99 USD

Add to Wish List

The VAC Motorsports ARP Head Stud Kit was put together by VAC and ARP’s finest engineers. This is a completely custom kit designed specifically for the almighty N54. *High Boost (25+ psi application) option features: (14) 11mm ARP Head Studs (14) ARP Washers for 11mm Studs (14) ARP Nuts for 11mm Studs Install Tips: MUST drill and tap the (4) 9mm holes in the engine block to make them 11mm holes. This way all the engine block holes are 11mm, and fit ALL (14) 11mm Studs. Torque Specs: All studs torque down through 3-equal steps to 95 ft lbs ***This is NOT the Chrysler and Volvo stud kits! VAC Motorsports and ARP engineers designed and assembled this kit with high grade material, specifically so standard street-use or high-boost N54 owners have a PROPER kit that does not fail over time, such as the retro-fit Chrysler and Volvo head stud kits. ARP is the world leader in fastener technology. Makers of the finest fasteners in the market, especially for BMW engines, ARP is the brand you can count on when you want the highest reliability possible. If you are looking for high performance from your BMW engine, then ARP Head Stud Kits are a must. All kits come complete with hardened parallel-ground washers and aerospace-quality nuts.

Show More Show Less

Schrick Intake Camshaft - E46 M3, MZ3, MZ4 (S54) - 288 Degree, 12.5mm...

T#:3572

Part#: TMS3572

Ships on Dec 3, 2026

$ 1,775.98 USD

Add to Wish List

Qty

$ 1,775.98 USD

Add to Wish List

E46 M3 Schrick 288 Degree Intake Camshaft with 12.5mm valve lift. Originally desinged for the M3 CSL but works great in a standard M3. A new rocker arm is required (Schrick or new BMW part #11337833259). This is a more agressive cam that the Schrick 280 degree cam that we also offer for the E46M3

BMW Schrick Technical Specs

Schrick Technical Information / Specs

This item fits the following BMWs:
2001-2006 E46 BMW M3
2001-2002 Z3 BMW M Roadster M Coupe
2006-2008 E85 BMW Z4 M Roadster M Coupe

Show More Show Less

Schrick Exhaust Camshaft - E46 M3, MZ3, MZ4 (S54) - 272 Degree, 12.5m...

T#:11749

Part#: TMS11749

Ships on Dec 3, 2026

$ 824.99 USD

Add to Wish List

Qty

$ 824.99 USD

Add to Wish List

E46 M3 Schrick 272 Degree Exhaust Camshaft with 12.5mm valve lift. New rocker arms are required (BMW part #11337833259 or a new Schrick part).

BMW Schrick Technical Specs

Schrick Technical Information / Specs

This item fits the following BMWs:
2001-2006 E46 BMW M3
2001-2002 Z3 BMW M Roadster M Coupe
2006-2008 E85 BMW Z4 M Roadster M Coupe

Show More Show Less

Schrick Intake Camshaft - E46 M3, MZ3, MZ4 (S54) - 280 Degree, 12.5mm...

T#:11748

Part#: TMS11748

Ships on Dec 3, 2026

$ 1,867.99 USD

Add to Wish List

Qty

$ 1,867.99 USD

Add to Wish List

E46 M3 with S54 engine Schrick 280 Degree Intake Camshaft with 12.5mm valve lift. A new rocker arm is required (Schrick or new BMW part #11337833259).

Schrick Technical Information / Specs

This item fits the following BMWs:
2001-2006 E46 BMW M3
2001-2002 Z3 BMW M Roadster M Coupe
2006-2008 E85 BMW Z4 M Roadster M Coupe

Show More Show Less

Schrick Camshaft - M20 288 degree

T#:3501

Part#: 05601880-00

Ships on Dec 3, 2026

$ 490.00 USD

Add to Wish List

Qty

$ 490.00 USD

Add to Wish List

SEE T#338236

Schrick Performance Camshaft Set - 238/272 - F80 M3, F82/83 M4 S55 ...

T#:637691

Part#: SCHCSSS55238/272

Back Ordered

$ 1,899.99 USD

Add to Wish List

Qty

$ 1,899.99 USD

Add to Wish List

High-performance camshafts are key to increasing the top-end power output of your S55 engine at high boost. 238/272 degree, 10.6mm/10.5mm lift. Perfectly compatible with OE valves, springs, VANOS, Valvetronic etc

Show More Show Less

Schrick Exhaust Camshaft - E46 M3, MZ3, MZ4 (S54) - 280 Degree, 12.5m...

T#:1259

Part#: TMS1259

In Stock

Sale - Save 5% $ 1,775.98

This product was last offered at the strikethrough price on
07-07-2026

$ 1,687.18 USD

Add to Wish List

Qty

Sale - Save 5%

$ 1,775.98

This product was last offered at the strikethrough price on
07-07-2026

$ 1,687.18 USD

Add to Wish List

E46 M3 Schrick 280 Degree Exhaust Camshaft with 12.5mm lift. This was originally desinged for the M3 CSL but works great in the standard M3. This cam is slightly more agressive than the "original" Schrick 272 degree (which we also offer). A new rocker arm is required (Schrick or new BMW part #11337833259).

BMW Schrick Technical Specs

Schrick Technical Information / Specs

This item fits the following BMWs:
2001-2006 E46 BMW M3
2001-2002 Z3 BMW M Roadster M Coupe
2006-2008 E85 BMW Z4 M Roadster M Coupe

Show More Show Less

Schrick Exhaust Camshaft - E46 M3, MZ3, MZ4 (S54) - 280 Degree, 12.5m...

T#:338216

Part#: TMS1259

Ships on Dec 3, 2026

Starting at $ 2,432.99 USD

Add to Wish List

Starting at $ 2,432.99 USD

Add to Wish List

E46 M3 Schrick 280 Degree Exhaust Camshaft with 12.5mm lift. This was originally desinged for the M3 CSL but works great in the standard M3. This cam is slightly more agressive than the "original" Schrick 272 degree (which we also offer). A new rocker arm is required (Schrick or new BMW part #11337833259).

BMW Schrick Technical Specs

Schrick Technical Information / Specs

This item fits the following BMWs:
2001-2006 E46 BMW M3
2001-2002 Z3 BMW M Roadster M Coupe
2006-2008 E85 BMW Z4 M Roadster M Coupe

Show More Show Less

BMW US S50 6 Cyl. 284-Degree - Intake Camshaft

T#:554296

Part#: 0284E1840-0V1

In Stock

Sale - Save 15% $ 1,727.99

This product was last offered at the strikethrough price on
07-07-2026

$ 1,468.79 USD

Add to Wish List

Qty

Sale - Save 15%

$ 1,727.99

This product was last offered at the strikethrough price on
07-07-2026

$ 1,468.79 USD

Add to Wish List

Schrick has been dedicated to engine performance through the development of only the highest-quality camshafts for more than 40 years. They've created a bond with BMW enthusiasts nearly the entire time, offering options for both the street and track using top materials for strength and accuracy. Schrick has grown into a technology center offering one of the most advanced locations for engine testing and manufacturing. These are the same cams used by many high-end German tuners who are achieving sizeable gains with the US S50 engine. For the power-hungry, these cams are a great way to achieve a linear increase in horsepower from mid-range, up to redline. Duration Intake- 284 Duration Intake @ 1mm - 253 Intake Peak Timing - 122 Cam Lobe Lift Intake - 11, 9 Valve Lift w/o Valve Clearance Intake - 11, 9 Valve Clearance Intake - 0,25

Show More Show Less

E60 M5/E63 M6 WPC Treated S85 Rod Bearings (Set)

T#:388759

Part#: 11247841702WPCKT

In Stock

$ 1,086.99 USD

Add to Wish List

Qty

$ 1,086.99 USD

Add to Wish List

These WPC-treated bearings are the best we have seen for the S85. WPC is a shot-peening treatment at a microscopic level. It's perfect for sensitive surfaces like bearings. The WPC treatment removes imperfections and high spots, while creating a surface that retains oil better than the original surface. This greatly reduces friction. The bearings in this kit are factory BMW bearings that are sent to WPC for treatment. The treated bearings are stronger with less metal fatigue and less friction than buying off-the-shelf bearings from the dealer.

Price is for a complete set of S85 upgraded rod bearings.

Show More Show Less

WPC Treated Main Bearing Set - Standard Size - E30 M3 2.3 Liter ...

T#:13299324

Part#: 11210666110WP2KT

Ships on Sep 11, 2026

$ 174.99 USD

Add to Wish List

Qty

$ 174.99 USD

Add to Wish List

Vargas "Spline Lock" Crank Hub Solution - N54

T#:558924

Part#: VTT-N54-CRANKHUB

Ships in 10 Business Days

$ 818.99 USD

Add to Wish List

Qty

$ 818.99 USD

Add to Wish List

Anyone with a modified N54 knows the risks involved. Upping the performance of any engine can come with some inherent risk; if we add more boost but not fuel, detonation will occur (or worse). Furthermore, improper installation, maintenance, or operation can turn a perfectly healthy engine into a paperweight. The worst failures, however, are the ones we don't plan for. When the engine simply can't handle the stresses its put under, or the design is such that it simply does not support extreme conditions. Enter the N54 crank hub. Under certain conditions, it likes to spin without warning, even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines that press into the crank and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Vargas spent many months testing, and retesting this design, utilizing well over 10 different samples to come to the final production version. During testing, the final hub managed to break the testing rig before slipping. These have been bench-tested, and real-world tested on the VTT N54 race car spinning 8K RPM, and making well over 900WHP. Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and Turner Motorsport are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution. The worst failures, however, are the ones we don't plan for. When the engine simply can't handle the stresses its put under, or the design is such that it simply does not support extreme conditions. Enter the N54 crank hub. Under certain conditions, it likes to spin without warning, even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines that press into the crank and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Vargas spent many months testing, and retesting this design, utilizing well over 10 different samples to come to the final production version. During testing, the final hub managed to break the testing rig before slipping. These have been bench-tested, and real-world tested on the VTT N54 race car spinning 8K RPM, and making well over 900WHP. Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and Turner Motorsport are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution. The product comes with a 1-year unlimited mileage warranty from manufacturer defects.

Show More Show Less

Spline Lock Crank Hub Solution

T#:8061334

Part#: VTT-N55-CRANKHUB

Ships in 10 Business Days

$ 818.99 USD

Add to Wish List

Qty

$ 818.99 USD

Add to Wish List

Under certain conditions, the N55 crank hub likes to spin, without warning and even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines which press into the crank, and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and ECS are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines which press into the crank, and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and ECS are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution. The product comes with a 1-year unlimited mileage warranty from manufacturer defects.

Show More Show Less

Spline Lock Crank Hub Solution W/ Crank Bolt Capture - N54

T#:18733527

Part#: VTT-CRANKHUB-2

Ships in 10 Business Days

$ 871.99 USD

Add to Wish List

Qty

$ 871.99 USD

Add to Wish List

Anyone with a modified N54 knows the risks involved. Upping the performance of any engine can come with some inherent risk; if we add more boost but not fuel, detonation will occur (or worse). Furthermore, improper installation, maintenance, or operation can turn a perfectly healthy engine into a paperweight. The worst failures, however, are the ones we don't plan for. When the engine simply can't handle the stresses its put under, or the design is such that it simply does not support extreme conditions. Enter the N54 crank hub. Under certain conditions, it likes to spin without warning, even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines that press into the crank and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Vargas spent many months testing, and retesting this design, utilizing well over 10 different samples to come to the final production version. During testing, the final hub managed to break the testing rig before slipping. These have been bench-tested, and real-world tested on the VTT N54 race car spinning 8K RPM, and making well over 900WHP. Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and Turner Motorsport are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution.

Show More Show Less

BMW M50 M52 S50 S52 Shrick Camshaft Set 276 intake / 270 exhaust ...

T#:4731086

Part#: SCH-CSS-S52-276/

Ships in 2 Business Days

$ 2,640.99 USD

Add to Wish List

Qty

$ 2,640.99 USD

Add to Wish List

Elevate your BMW's engine performance with Schrick's premium camshafts, crafted with over 40 years of dedication to excellence. Catering to both street and track enthusiasts, Schrick ensures top-quality materials for strength and accuracy. This renowned brand has formed a lasting bond with BMW enthusiasts, providing advanced camshaft options that have stood the test of time.

Premium Schrick camshafts for BMW
Over 40 years of dedicated engine performance expertise
Ideal for both street and track applications
Top-quality materials for strength and accuracy
Trusted by BMW enthusiasts worldwide
Advanced engine testing and manufacturing technology

Show More Show Less

Spline Lock Crank Hub Solution W/ Hardware Package - N54

T#:18733526

Part#: VTT-CRANKHUB-4

Ships in 10 Business Days

$ 880.99 USD

Add to Wish List

Qty

$ 880.99 USD

Add to Wish List

Anyone with a modified N54 knows the risks involved. Upping the performance of any engine can come with some inherent risk; if we add more boost but not fuel, detonation will occur (or worse). Furthermore, improper installation, maintenance, or operation can turn a perfectly healthy engine into a paperweight. The worst failures, however, are the ones we don't plan for. When the engine simply can't handle the stresses its put under, or the design is such that it simply does not support extreme conditions. Enter the N54 crank hub. Under certain conditions, it likes to spin without warning, even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines that press into the crank and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Vargas spent many months testing, and retesting this design, utilizing well over 10 different samples to come to the final production version. During testing, the final hub managed to break the testing rig before slipping. These have been bench-tested, and real-world tested on the VTT N54 race car spinning 8K RPM, and making well over 900WHP. Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and Turner Motorsport are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution.

Show More Show Less

VTT N54 “Spline Lock” CrankHub Solution Package W/ Crank Bolt Cap...

T#:19395579

Part#: VTTCRANKHUBPKG

Ships in 10 Business Days

$ 934.99 USD

Add to Wish List

Qty

$ 934.99 USD

Add to Wish List

VTT is proud to offer the only complete N54 complete crank hub solution that does NOT require the crank to be drilled for pins. Our hub uses our proprietary “Spline Lock” technology that uses high tolerance machined splines which press into the crank, and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). We spent many months testing, and retesting this design, utilizing well over 10 different samples to come to our final production version. During testing, our final hub managed to break our testing rig before slipping. These have been bench tested, and real-world tested on the VTT N54 race car spinning 8K RPM and making well over 900WHP. This technology means our hub installs the same as a stock hub, no drilling of the crank, which means MUCH less labor is involved and is reversible is ever wanting to be uninstalled leaving no holes in the crank. The “Spline Lock” is ONLY available with the VTT Crank bolt capture for the ULTIMATE Crank Hub solution for your BMW. These parts are designed to be used together, and the spline lock should not run without the CBC VTT “Spline Lock” Crank hubs are CNC manufactured from 440C tool Steel with a Rockwell rating of HRC60 for the ultimate in durability, and toughness. Hub Plus OEM bolt OEM Oil pump sprocket OEM oil sprocket retainer VTT Crank bolt capture

Show More Show Less

CP Carrillo Forged Piston Set - BMW M20B25

T#:23847551

Part#: CP-FPS-M20-B25

Ships in 2 Business Days

$ 1,399.99 USD

Add to Wish List

Qty

$ 1,399.99 USD

Add to Wish List

Elevate Your Engine's Performance with Customizable CP Pistons

When it comes to optimizing your engine's performance, flexibility is key. That's why we offer a range of CP pistons with customizable compression ratios to cater to your specific needs. Whether you're embarking on a basic engine rebuild, planning to implement a low boost turbo or supercharger, or aiming to maximize power with high-performance camshafts, we have the ideal piston solution for you.

Our collaboration with CP ensures that you'll receive pistons of the highest quality, meticulously designed to meet the most demanding expectations. These pistons are a top choice for high-performance and racing engines.

We maintain a diverse selection of compression ratios in stock, making it convenient to find the right fit for your project. And if you require a custom piston application, our efficient service has you covered.

BORE: 84mm
Rod Length: 135mm
Compression Ratio: 8.5:1

Show More Show Less

WPC Treated Genuine BMW Rod Bearings - Full Set

T#:389729

Part#: 11241407493WPCKT

Ships in 1-2 days

$ 1,231.84 USD

Add to Wish List

Qty

$ 1,231.84 USD

Add to Wish List

These WPC-treated bearings are the best we have seen for the S62. WPC is a shot-peening treatment at a microscopic level. It's perfect for sensitive surfaces like bearings. The WPC treatment removes imperfections and high spots, while creating a surface that retains oil better than the original surface. This greatly reduces friction. The bearings in this kit are factory BMW bearings that are sent to WPC for treatment. The treated bearings are stronger with less metal fatigue and less friction than buying off-the-shelf bearings from the dealer.

Price is for a complete set of S62 upgraded rod bearings.

Show More Show Less

N54 Spline Lock Crank Hub Solution With Complete Package

T#:18733525

Part#: VTT-CRANKHUB-3

Ships in 5 Business Days

$ 939.99 USD

Add to Wish List

Qty

$ 939.99 USD

Add to Wish List

Anyone with a modified N54 knows the risks involved. Upping the performance of any engine can come with some inherent risk; if we add more boost but not fuel, detonation will occur (or worse). Furthermore, improper installation, maintenance, or operation can turn a perfectly healthy engine into a paperweight. The worst failures, however, are the ones we don't plan for. When the engine simply can't handle the stresses its put under, or the design is such that it simply does not support extreme conditions. Enter the N54 crank hub. Under certain conditions, it likes to spin without warning, even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines that press into the crank and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Vargas spent many months testing, and retesting this design, utilizing well over 10 different samples to come to the final production version. During testing, the final hub managed to break the testing rig before slipping. These have been bench-tested, and real-world tested on the VTT N54 race car spinning 8K RPM, and making well over 900WHP. Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and Turner Motorsport are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution.

Show More Show Less

JE Pistons Forged Piston Set - 84mm - 10.5:1 - M52

T#:11857228

Part#: JE-FPS-M52-84-10

Ships on Sep 1, 2026

$ 1,439.99 USD

Add to Wish List

Qty

$ 1,439.99 USD

Add to Wish List

Boost Your BMW's Engine with JE Pistons

Upgrade your BMW's engine with the JE Pistons Forged Piston Set designed for the M52 engine. These high-quality forged pistons feature a diameter of 84mm and a compression ratio of 10.5:1, ensuring improved performance and reliability for your BMW.

Enhances engine performance and reliability
Precision-engineered for optimal fit and function
High-quality forged construction ensures durability
Designed specifically for the M52 engine

Show More Show Less

ARP Rod Bolt Set - M20 - 53mm

T#:1061435

Part#: ARP-RBS-M20

Ships on Sep 1, 2026

$ 314.99 USD

Add to Wish List

Qty

$ 314.99 USD

Add to Wish List

ARP, the world’s leader in fastener technology. There is no substitute for the best! Planning to boost your M20? Building a high HP stroker engine? This rod bolt kit is for you! This kit provides higher strength, more clamping power, and the option to re-use the hardware unlike your OEM bolts. We run these in many of our own builds as well and are 110% satisfied with the fit and finish of these ARP bolts. We offer a 53mm UHL version for those running OEM M20 rods or a 44mm UHL version for those who have upgraded to S50/S52 OEM rods.

Show More Show Less

VAC Motorsports Performance Coated Rod Bearing Set - BMW E30 M3 S14 ...

T#:638307

Part#: VAC-HPRBS-S14STD

Ships on Sep 1, 2026

$ 249.99 USD

Add to Wish List

Qty

$ 249.99 USD

Add to Wish List

VAC Rod Bearing Sets are specially coated to reduce friction to a minimum; enabling lower temps and faster revolutions in your expensive S14 engine. The coated bearings are thermal breakdown resistant, helping to prevent premature engine failures under stress when things are most critical. The rod bearing area is a common stress area in the S14, these bearings can last much longer than any normal bearing sets and are used in all of VAC's highest performance BMW engine builds. These bearings have become a favorite product of all of VAC's race and engine building customers around the globe who have reported unparalleled wear characteristics under all conditions. Made for VAC by the same company who manufactures for the US military, NASCAR teams, and other customers that require "mission-critical" quality. If you are looking for high-performance rod bearings, this is the set for your S14. VAC Tech Notes: As with all bearings, please check your tolerances and size before installation. Due to the specialized tools needed, professional install recommended. There are no returns available on any engine bearings.

Show More Show Less

Performance Camshaft Set - 238/272

T#:26904914

Part#: SCH-N52-238/272

Special Order: No Guaranteed ETA

$ 1,749.99 USD

Add to Wish List

Qty

$ 1,749.99 USD

Add to Wish List

Schrick Camshaft Set - E46 325, 330, 530, X5 3.0, Z3 3.0 - 264/248 ...

T#:4048

Part#: E46-M54-SCHRICK

Ships on Dec 3, 2026

$ 2,915.38 USD

Add to Wish List

Qty

$ 2,915.38 USD

Add to Wish List

Schrick 264 degree (10.5mm lift) intake and 248 degree (10mm lift) exhaust cams provide a power boost at mid-high RPM range without software changes. As used in our 330i ZHP Project Car! These are also available for track / race applications in 272 intake and 256 exhaust durations. We also recommend purchasing Supertech High Performance Valve Springs Call us for details. Professional installation required for all Shrick Camshafts.

BMW Schrick Technical Specs

Schrick Technical Information / Specs

Show More Show Less

Schrick Camshaft - E30 325i, E34 525 (M20) 304 degree

T#:338233

Part#: 05601040-00

Ships on Dec 3, 2026

Starting at $ 1,489.99 USD

Add to Wish List

Starting at $ 1,489.99 USD

Add to Wish List

Schrick's most aggressive cam for the M20 engine. The 304-degree will make big power at the top but there will be a loss of low-end torque so this cam is only recommended for cars that see most of their time above 4000 rpm. Schrick High Performance valve springs are strongly recommended. This cam has a 12.2mm lift and will not clear stock M20 pistons.

BMW Schrick Technical Specs

Schrick Technical Information / Specs

Show More Show Less

Schrick Camshaft - E30 325i, E34 525 (M20) 284 degree

T#:338235

Part#: 05601840-00

Ships on Dec 3, 2026

Starting at $ 479.00 USD

Add to Wish List

Starting at $ 479.00 USD

Add to Wish List

E30 325i, E34 525 (M20) 284 degree Schrick Camshaft. This is Step 2 in Schrick's line of performance cams. The 284 degree cam will be great for owners who want to retain their driveability on the street and only need a modest boost in top-end RPM. Schrick recommends replacing the valve springs with high-performance springs for this application.

BMW Schrick Technical Specs

Schrick Technical Information / Specs

Show More Show Less

Schrick Camshaft Set - E36 M3-spec - 252/244 Degree

T#:21521

Part#: TMS21521

Ships on Dec 3, 2026

$ 3,470.66 USD

Add to Wish List

Qty

$ 3,470.66 USD

Add to Wish List

These Schrick camshafts are the same specs as the stock US S50 cams -
Intake: 252 degree, 10.2mm lift
Exhaust: 244 degree, 9.5mm lift

With original S50/S52 cams in short supply, and a new set running over $2,000 from BMW, you can source new M3-spec cams from Schrick. These are the same specs as the US S50 engine and very close to the stock S52 cams. These make a great upgrade for M50 (325i, 525i) and M52 engines (328i, 528i) with the proper tuning. These bolt in just like the stock and M3 cams with no special hardware upgrades required - use your stock valve springs, lifters, etc. But for reliability we recommend replacing the lifters, valve springs, and retainers with new stock parts on high mileage engines.

Full cam specs: Schrick Technical Information / Specs

This item fits the following BMWs:
1993-1999 E36 BMW 325i 325is 325ic 328i 328is 328ic M3
1993-1995 E34 BMW 525i
1997-1998 E39 BMW 528i
1997-1998 Z3 BMW Z3 2.8
1998-1999 Z3 BMW M Roadster M Coupe

Show More Show Less

BMW S52/M52 6 Cyl. 264-Degree - Intake Camshaft

T#:300487

Part#: 261.E1.641-V2C

Special Order: No Guaranteed ETA

$ 1,398.99 USD

Add to Wish List

Qty

$ 1,398.99 USD

Add to Wish List

Schrick has been dedicated to engine performance through the development of only the highest-quality camshafts for more than 40 years. They've created a bond with BMW enthusiasts nearly the entire time, offering options for both the street and track using top materials for strength and accuracy. Schrick has grown into a technology center offering one of the most advanced locations for engine testing and manufacturing. These are the same cams used by many high-end German tuners who are achieving sizeable gains with the S50 and S52 engines. For the power-hungry, these cams are a great way to achieve a linear increase in horsepower from mid-range, up to redline. Duration Intake - 264 Duration Intake @ 1mm - 227 Intake Peak Timing - Cam Lobe Lift Intake - Valve Lift w/o Valve Clearance Intake - Valve Clearance Intake -

Show More Show Less

Schrick Camshaft Set - E36 M3, MZ3, M52 inc 2.8 1995-99 - 256/264 ...

T#:3859

Part#: TMS3859

Ships on Dec 3, 2026

$ 2,799.99 USD

Add to Wish List

Qty

$ 2,799.99 USD

Add to Wish List

For the US E36 M3. Schrick 264/256 degree camshafts boost mid-high end power for that extra motivation at higher rpm. Low-end torque is not seriously affected due to the M50/M52s VAN0S System. And, higher profile cams work extremely well with an upgraded intake and exhaust. When upgrading the cams there are other areas you must take into consideration. Higher-flow fuel injectors, larger mass-air sensor, and custom programming are strongly recommended. Turner Motorsport sells complete intake & cam packages that boost power to over 290hp. See the Engine section under Camshafts for more info.

Cam Specs:
Intake - 264 degree, 11.2mm lift
Exhaust - 256 degree, 10.6mm lift

Schrick Technical Information / Specs

This item fits the following BMWs:
1993-1998 E36 BMW 325i 325is 325ic 328i 328is 328ic M3
1993-1995 E34 BMW 525i
1997-1998 Z3 BMW Z3 2.8
1998-1999 Z3 BMW M Roadster M Coupe

Show More Show Less

Schrick Camshaft Set - E46 330, 530, X5 3.0, Z3 3.0 - 272/256 ...

T#:200185

Part#: TMS200185

Ships on Dec 3, 2026

$ 3,340.69 USD

Add to Wish List

Qty

$ 3,340.69 USD

Add to Wish List

Schrick 272 degree (10.9mm lift) intake and 256 degree (10.4mm lift) exhaust cams provide a power boost at mid-high RPM range without software changes. We also recommend purchasing Supertech High Performance Valve Springs Call us for details. Professional installation required for all Shrick Camshafts.

BMW Schrick Technical Specs

Schrick Technical Information / Specs

Show More Show Less

Schrick Camshaft - E30 M3 276 degree

T#:203

Part#: TMS203

Special Order: No Guaranteed ETA

$ 1,503.99 USD

Add to Wish List

Qty

$ 1,503.99 USD

Add to Wish List

276-deg Performance Camshaft. This is the next step above the Evo 2/3 cams that we also sell and will produce greater top-end power with only slight loss in torque. This cam can be used on the intake side with a stock exhaust cam OR it can be used on the exhaust side with the 284-deg Schrick cam as the intake.

BMW Schrick Technical Specs

Schrick Technical Information / Specs br>
This item fits the following BMWs:
1988-1991 E30 BMW M3 - S14 engine

Show More Show Less

Project Cars

SELECT YOUR BMW

BMW Internal Engine Parts

Sub-Categories

Elevate Your Engine's Performance with Customizable CP Pistons

Boost Your BMW's Engine with JE Pistons

Select Vehicle

Purpose

Category

Brand

Price

Special Offers

Shipping

Narrow Results