Emissions System

Turner Motorsport Silicone PCV Hose for BMW M57

Upgrade your BMW M57 engine with our Silicone PCV Hose, a premium replacement for the fragile, failure-prone factory hose. Over time, the stock rubber hose deteriorates due to constant exposure to heat and oil, leading to cracks and leaks. Our solution? A high-quality silicone hose engineered for superior durability and long-term reliability.

To further enhance performance, we’ve lined the hose with fluorosilicone, providing exceptional resistance to oil and chemical degradation. Designed in-house using advanced CAD modeling and 3D scanning, this hose offers a precise OEM fit while eliminating the common weaknesses of rubber construction.

Each kit includes stainless steel hose clamps for a secure, hassle-free installation. Whether you’re replacing a worn-out PCV hose or upgrading for added peace of mind, this premium solution ensures your BMW M57 runs smoothly and efficiently for years to come.

Features:

Direct OEM Fit – Retains factory hose dimensions while eliminating reliability issues.
High-Performance Silicone – Resists heat-related wear for long-lasting durability.
4-Ply Fluorosilicone Lining – Superior protection against oil and chemical exposure.
Stainless Steel Clamps Included – Secure installation and extended service life.
Give your BMW M57 the reliability it deserves—upgrade to the Turner Motorsport Silicone PCV Hose today!

The factory rubber/plastic hoses become brittle and crack over time. Brittle and cracked hoses can cause multiple vacuum leaks that are impossible to repair without hose replacement. Vacuum leaks can cause many problems including rough running, missing, stalling at idle, and even a no-start condition.

The factory hoses offered through BMW are plastic and will yield the same results of becoming brittle and damaged over time. Our solution is a premium replacement that will outlast everyone of the OEM replacements. Our Silicone Crankcase Vent Hose can be used to replace the factory brittle hose to ensure your S54 is free from vacuum leaks and performing properly.

CSL Vent Hose (11157833649) - Silicone Crankcase Vent hose is a direct replacement

Key benefits:

Lifetime replacement of the brittle OEM plastic crankcase breather hose that is susceptible to cracking overtime from constant heat cycling

Design:

Retains OEM hose end fittings to ensure proper seal

“Black” 3 ply reinforced silicone w/ “White” Turner logo

A combination of billet fittings and AN lines for an upgraded and serviceable crankcase vent hose. Attaches between the oil separator and the CSL air box.

The factory rubber/plastic hoses become brittle and crack over time. Brittle and cracked hoses can cause multiple vacuum leaks that are impossible to repair without hose replacement. Vacuum leaks can cause many problems including rough running, missing, stalling at idle, and even a no-start condition. The factory hoses offered through BMW are plastic and will yield the same results of becoming brittle and damaged over time.

We have created a full motorsport style solution with our CSL Crankcase made from machined 6061 billet aluminum with AN style fittings and nylon fiber braided lines. This is a fully serviceable replacement that will outlast every one of the OEM replacements. Our AN crankcase line can be used to replace the factory brittle hose to ensure your S54 is free from vacuum leaks and performing properly.

OEM CSL Vent Hose (11157833649) - Direct Replacement

Key benefits:

Lifetime replacement of the brittle OEM plastic crankcase breather hose
Fully Serviceable
Motorsport Aesthetic to compliment your CSL Intake Plenum
Design:

Fittings are made from billet 6061-T6 aluminum and finished in Type II black anodizing
Pre-anodized machined Turner branding
Nylon fiber braided lines
Fittings are a direct replacement for the plastic OEM fittings

Restore proper engine ventilation with this premium replacement Crankcase Breather Valve (11127809512).

Designed to match the performance of the original BMW unit (OE 11-12-7-809-512 / 11-12-7-803-790), this valve maintains correct crankcase pressure, helps prevent oil buildup, and supports clean, efficient engine operation.

Crafted from high-quality, long-lasting materials and shaped to replicate the factory design, it installs easily in place of the stock breather without any modifications required.

Whether you’re addressing pressure-related drivability issues, refreshing your engine’s ventilation system, or performing preventative maintenance, this breather valve provides dependable performance and protects your BMW’s engine for the long haul.

The oxygen sensor is vital to the performance and drivability of your car. The engine computer relies on data from the sensor to make adjustments in engine efficiency and performance. When your BMW oxygen sensor fails, the computer can no longer sense the air/fuel ratio, so it ends up guessing -- resulting in poor performance, poor gas mileage, and increased pollution. Make sure your BMW engine performs as it should, and doesn't use more fuel than it needs to, by simply changing your oxygen sensor today. There is no lifespan on O2 sensors but there are several fault codes that indicate a failed sensor (O2 monitoring, cat efficiency, O2 heating circuit, O2 readiness, and others). The O2 sensor is heated and has a self-calibration feature so once you get the codes or feel performance has suffered, a new sensor is a good starting point to get you back to peak performance.

This is a Bosch O2 sensor - also known as a Lambda probe. Bosch is an OEM supplier to BMW.

Position: post-cat, after the catalytic converter (pre-cat). Bank 1 and Bank 2 use the same sensor (2 required per vehicle).

This item fits the following BMWs:
2006-2010 E60 BMW M5
2006-2010 E63 E64 BMW M6

The oxygen sensor is vital to the performance and drivability of your car. The engine computer relies on data from the sensor to make adjustments in engine efficiency and performance. When your BMW oxygen sensor fails, the computer can no longer sense the air/fuel ratio, so it ends up guessing -- resulting in poor performance, poor gas mileage, and increased pollution. Make sure your BMW engine performs as it should, and doesn't use more fuel than it needs to, by simply changing your oxygen sensor today. There is no lifespan on O2 sensors but there are several fault codes that indicate a failed sensor (O2 monitoring, cat efficiency, O2 heating circuit, O2 readiness, and others). The O2 sensor is heated and has a self-calibration feature so once you get the codes or feel performance has suffered, a new sensor is a good starting point to get you back to peak performance. Bosch's Oxygen sensors are high quality and will give you the the longest and best performance for the price.

Bosch is one of the largest OEM producers of Genuine BMW and aftermarket parts in the world, providing parts for almost every major automotive manufacturer. Bosch has likely supplied many of the original electrical (and mechanical) parts for your BMW. Thanks to their quality, high durability, and reliability, you should expect a long service life from Bosch products.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

This item fits the following BMW Chassis:
E82,E90,E92,E93,F30,F34

Fits BMW Engines including:
N55 - up to 08/2013

Upgrade your N14 N18 1.6L Engine with the Vent Hose. This hose connects to the top valve cover with a special hose clip end and extends to the bottom side of the intake manifold, ensuring optimal performance of your Mini. It's a crucial component of the intake system, designed to enhance engine efficiency and longevity.

• Ensures proper ventilation of the engine
• Connects securely to the valve cover and intake manifold
• Facilitates efficient airflow within the engine compartment
• Compatible with N14 N18 1.6L Engine models
• Easy to install and replace as needed

The engine crankcase breather hose is a vital part of the Positive Crankcase Ventilation (PCV) system, responsible for directing pressurized air from the engine crankcase to the air/oil separator, also known as the PCV valve. This separator removes oil vapors from the air, allowing the oil to return to the engine while feeding the filtered air back into the intake system to support efficient combustion.

As a byproduct of the combustion process, positive crankcase pressure naturally builds up in the engine. The breather hose operates under constant exposure to heat, pressure, and an air/oil vapor mixture, making it prone to wear and failure over time. Ensuring the breather hose is in proper working condition is crucial for maintaining engine performance, adhering to emissions standards, and preserving the functionality of the PCV system. Promptly replace this component at the first signs of damage or degradation to avoid further complications.

The SCR reservoir heater, found in the DEF active tank, is a frequently failing component that can lead to emissions-related DTCs. When it fails, replacing the entire tank assembly is often necessary, which can be expensive if using Genuine parts.

Fortunately, Bosch offers a high-quality replacement heater and tank assembly, ensuring a seamless and reliable replacement process. Opting for Bosch means choosing a cost-effective repair solution that promises durability and longevity.

For a hassle-free replacement of your SCR heater, trust Bosch to deliver lasting performance.