Emissions System

Vents gases from the crankcase back into the intake.
When doing any sort of repair or maintenance there is no replacement for genuine factory parts. Turner Motorsport carries the Genuine BMW brand with pride and has the parts you need to complete your next project with confidence.

Genuine BMW Vent Hose
This item fits the following BMW Chassis:
E46 M3,E85 Z4M,E46,E85 Z4,E86 Z4

Fits BMW Engines including:
S54
 

After the introduction of the M52TU/M54 engines, BMW observed an uptick in CCV-related issues, especially in cold regions. Vehicles operating in extremely low temperatures often encountered a blockage in the CCV dipstick hose, leading to elevated crankcase pressure and visible blue smoke from the exhaust. To address this issue, BMW introduced cold climate-specific hoses with foam insulation, preventing condensation and facilitating quicker oil warm-up. This kit incorporates top-notch reproduction cold climate hoses to ensure optimal CCV performance across all weather conditions.

The crankcase ventilation valve, known as the oil separator, PCV, CCV, or crankcase pressure regulator valve, plays a vital role in redirecting oil from your vehicle's intake system back into the engine oil pan. This system comprises numerous plastic and rubber hoses, prone to damage due to prolonged exposure to chemicals and heat.

Designed to tackle or prevent impending CCV system failures, this kit includes four foam-insulated hoses made from durable plastic capable of withstanding heat fluctuations and chemical exposure. Additionally, a new ventilation valve is included for a comprehensive and long-lasting repair solution.

Signs indicating the need for crankcase ventilation system replacement include:

Whistling sounds from the intake manifold, caused by crankcase pressure venting through holes in the CCV hoses. Blue smoke emitting from the tailpipe, indicating oil consumption. Excessive oil usage. Milky or yellowish buildup under the oil cap, suggesting condensation due to ventilation valve malfunction. If you're experiencing misfires, lean fuel codes, decreased fuel efficiency, or noticeable oil consumption, it's advisable to overhaul your crankcase ventilation system. Opt for this reliable system from Febi-Bilstein for a repair that meets factory standards and ensures consistent performance.

Bad oxygen sensors can cause check engine lights and poor fuel mileage. Replace your faulty sensor with this high quality Bosch sensor to turn off your check engine light and restore fuel mileage.

This is the pre-cat oxygen sensor for cylinders 1-3 for BMW E46 M3. Bosch # 13 949. This is a OEM replacement part for BMW part # 11781743994.

Bosch is one of the largest OEM producers of Genuine BMW and aftermarket parts in the world, providing parts for almost every major automotive manufacturer. Bosch has likely supplied many of the original electrical (and mechanical) parts for your BMW. Thanks to their quality, high durability, and reliability, you should expect a long service life from Bosch products.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

This item fits the following BMWs:
2001-2006 E46 BMW M3 M3 convertible
2001-2002 Z3 BMW M Roadster M Coupe

Since the late 1800’s Febi has been fabricating replacement metal parts. This history is self-evident in the quality and vast amount of applications they serve. With more than 34,000 repair solutions for cars and commercial vehicles, you can be sure Febi has you covered.

Genuine BMW Connecting Line - Zyl 1-4
This item fits the following BMW Chassis:
E71,F01,F02,F10,F12,F13

Fits BMW Engines including:
N63
 

The oxygen sensor is vital to the performance and drivability of your car. The engine computer relies on data from the sensor to make adjustments in engine efficiency and performance. When your BMW oxygen sensor fails, the computer can no longer sense the air/fuel ratio, so it ends up guessing -- resulting in poor performance, poor gas mileage, and increased pollution. Make sure your BMW engine performs as it should, and doesn't use more fuel than it needs to, by simply changing your oxygen sensor today. There is no lifespan on O2 sensors but there are several fault codes that indicate a failed sensor (O2 monitoring, cat efficiency, O2 heating circuit, O2 readiness, and others). The O2 sensor is heated and has a self-calibration feature so once you get the codes or feel performance has suffered, a new sensor is a good starting point to get you back to peak performance. Bosch's Oxygen sensors are high quality and will give you the the longest and best performance for the price.

Bosch is one of the largest OEM producers of Genuine BMW and aftermarket parts in the world, providing parts for almost every major automotive manufacturer. Bosch has likely supplied many of the original electrical (and mechanical) parts for your BMW. Thanks to their quality, high durability, and reliability, you should expect a long service life from Bosch products.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

This item fits the following BMW Chassis:
E82,E90,E92,E93,F30,F34

Fits BMW Engines including:
N55 - Up to 08/2013

The oxygen sensor is vital to the performance and drivability of your car. The engine computer relies on data from the sensor to make adjustments in engine efficiency and performance. When your BMW oxygen sensor fails, the computer can no longer sense the air/fuel ratio, so it ends up guessing -- resulting in poor performance, poor gas mileage, and increased pollution. Make sure your BMW engine performs as it should, and doesn't use more fuel than it needs to, by simply changing your oxygen sensor today. There is no lifespan on O2 sensors but there are several fault codes that indicate a failed sensor (O2 monitoring, cat efficiency, O2 heating circuit, O2 readiness, and others). The O2 sensor is heated and has a self-calibration feature so once you get the codes or feel performance has suffered, a new sensor is a good starting point to get you back to peak performance. Bosch's Oxygen sensors are high quality and will give you the longest and best performance for the price.

This is the OEM Bosch oxygen sensor for BMW's with the N52, N54, and N55 3.0L engines. This 560mm bank 1 oxygen sensor is mounted after the catalytic converter.

Bosch is one of the largest OEM producers of Genuine BMW and aftermarket parts in the world, providing parts for almost every major automotive manufacturer. Bosch has likely supplied many of the original electrical (and mechanical) parts for your BMW. Thanks to their quality, high durability, and reliability, you should expect a long service life from Bosch products.

As a leading source of high-performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts. All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

Oil venting and circulation continues to be a problem on BMW engines and now even more so on the turbocharged N54 and N55 engines. The existing stock system does a very poor job of separating fluid and vapor and this leads to an oily film or even small pools of oil throughout the turbos and intake. We're seeing a lot more 135 and 335 cars with drivability and performance issues because oil has sneaked by the ring seals and is coating the intake piping, intercooler, intake valves, and other critical areas. The problem is worsened with higher boost levels. Oil is excellent for lubricating moving parts but terrible when it gets into the combustion chamber, effectively lowering the octane rating and reducing performance. Our own shop has gone the extra step and offers media blasting of the intake valves to strip away the oily buildup we have seen.

Our shop also strongly recommends an oil catch can be installed in the line for the crankcase vent. The oil catch can traps oil as it leaves the valve cover and holds it in a canister. This catch can is located on the cooler side of the engine where the oil will condense easier and stay in the can. Whatever minimal vapors are left over in the oil is then vented back through the canister and into the intake where it is safe to be burned up in the engine or recirculated back through the system again. This is the way the system was designed! At each oil change simply unscrew the canister and empty the trapped oil with your regular used oil. The Burger Tuning oil catch can is the best we have seen so far. Installing one of these will avoid costly repairs in the future and help maintain your boost and performance. It's one of the smartest modifications you can make because it demonstrates a well-thought out tuning strategy and care for the condition of your engine.

The BMS Oil Catch Can is made from aluminum and with a stealthy black anodized finish. It installs on the cooler side of the engine with a dedicated bracket and new oversized vent lines. The location is key as heat will evaporate the oil and send too much vapor back into the engine (where cooler air will turn it back into fluid). The BMS OCC also has a factory-like appearance. Since BMS designed their catch can from scratch they can guarantee it fits and performs correctly for the N54/N55 engine, unlike other catch cans on the market that are poorly retrofitted from other applications and under-sized for the N54 engine.

Note: Since the crankcase vent system is considered part of the overall emissions system, installing this may be a violation of local, state, and federal laws. While exemptions are made for track/race and off-road use, check with your local state inspection facility on using this in street-driven vehicles

BMS Oil Catch Can Features:
+ Increases air intake efficiency
+ Promotes engine longevity
+ Double-baffled design allows excellent air/oil separation
+ Large In/Out ports (no tapered sizes that slow flow)
+ Stealth mounting on cooler side of engine bay (promotes condensation of oil to vapor)
+ Anodized black lightweight aluminum
+ N54 version mounts out of sight under the cowl
+ Made in USA with a lifetime guarantee