This product was last offered at the strikethrough price on
06-14-2026
This product was last offered at the strikethrough price on
06-14-2026
Engineered in-house, our torque plate is designed to provide a robust and uniform clamping surface between the flywheel and crankshaft across a range of BMW engine applications. Compatible with both factory and Turner performance flywheels, it helps prevent surface galling and ensures consistent torque distribution during installation.
Features:
Prevents galling and wear at the crankshaft-to-flywheel interface under high clamping loads
Promotes even load distribution for improved fastener integrity and long-term reliability
Compatible with a variety of BMW flywheel setups, including OEM and aftermarket configurations
Design:
Precision-machined from cold rolled steel for high strength and dimensional accuracy
Heat treated to 32 HRC for increased surface hardness and wear resistance
Clear zinc anodized for enhanced corrosion protection
Laser-etched Turner logo
Ideal for performance builds and drivetrain refreshes, this torque plate is a critical component for maintaining proper flywheel installation and maximizing long-term durability across multiple BMW platforms.
This product was last offered at the strikethrough price on
06-14-2026
This product was last offered at the strikethrough price on
06-14-2026
The factory BMW S55 dual-mass flywheel is engineered with comfort in mind, catering to the luxury-oriented expectations of the brand’s driving experience. Its design focuses on dampening drivetrain vibrations, smoothing out gear transitions, and minimizing harshness during operation. However, this refinement costs valuable performance. The dual-mass flywheel adds a substantial 26.5 lbs of rotational mass to the drivetrain, which significantly hinders throttle response and makes rev-matching feel sluggish and disconnected. Moreover, dual-mass flywheels are notorious for being a weak link in modified or high-performance builds and can prove costly to replace when they inevitably fail.
Our Single-Mass Lightweight Flywheel Conversion addresses all of these shortcomings with a purpose-built, lightweight, single-mass design that prioritizes performance. Weighing in at only 18.5 lbs., this design significantly reduces rotational mass, allowing your S55 to achieve its true motorsport potential!
Features & Benefits:
Precision machined from 4140 HT heat-treated chromoly steel for exceptional toughness, even wear properties, and increased durability.
Material quality promotes even wear across the entire friction surface, prolonging component lifespan.
Heat treated to HRC 28-32, tempered to relieve stress and improve dimensional stability.
Hardness improves component wear characteristics.
Black oxide coated for corrosion resistance on non-friction surfaces.
Precision balanced to exceed OEM specification (G16 spec to 175g-mm).
SFI 1.1 certified to ensure safe operation under extreme operating conditions.
Specifically designed to work with S55 OE-architecture clutches.
Optimized step height maximizes clutch clamp load and offers a prolonged service life.
Performance:
10 lbs. lighter than the factory BMW flywheel!
OEM Dual-Mass: 26.5 lbs.
Turner Motorsport Single-Mass: 18.5 lbs.
Faster revs
Improved throttle response and acceleration
Allows for a more engaging driving experience and delivers a feeling of direct connection
Installation:
Flywheel Hardware: For added peace of mind, apply Blue or Orange Loctite when installing factory flywheel bolts that do not come with pre-applied threadlocker.
This product was last offered at the strikethrough price on
06-14-2026
This product was last offered at the strikethrough price on
06-14-2026
Engineered in-house, we designed this lightweight, single-mass flywheel to provide more than 10 pounds of weight savings over the factory flywheel. While some ultra-lightweight performance flywheels are manufactured from aluminum, our designers opted for a more driveable experience with steel. The mass provided by steel helps dampen vibrations and noise, delivering near-factory refinement with most of the benefits of a lightweight flywheel: quicker throttle response, improved durability (and longevity), and more effective transfer of power to the wheels.
Modern flywheels are built with additional components that are designed to dampen and minimize vibrations from the engine and transmission. Weight has increased and reliability has decreased. With additional weight more energy is required for it to move. A lightweight flywheel does away with the dual mass design and its additional mass so more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance. And with a single-mass flywheel the unreliable DMF design is eliminated.
When it comes to selecting a clutch to pair with a lightweight flywheel, consider the driving you’ll be doing. As a single mass flywheel eliminates the dual-mass dampening of the factory flywheel, to retain the lowest noise, lowest harshness driving experience possible, select a clutch with a dampened disc such as the ACT Heavy Duty. For dedicated track cars, a solid clutch hub is appropriate.
Our recommendations:
Street: ACT Heavy Duty
Track: ACT Xtreme for high torque cars or OE 335is LuK (with 440lbs-ft or less)
Features:
Precision machined from 4140 HT heat treated chromoly steel for exceptional toughness, even wear properties, and durability.
Material quality promotes even wear across the entire friction surface
Heat treated to HRC 28-32, tempered to relieve stress and improve dimensional stability and elevated temperatures
Hardness improves wear characteristics
Black oxide coated for corrosion resistance on non-friction surfaces.
8620 steel pilot bearing pin, case hardened and Precision ground for maximum wear resistance.
Precision balanced to exceed OEM specification (G16 spec to 175g-mm).
SFI 1.1 tested and certified to ensure safe operation under extreme operating conditions
SFI 1.1 specifies minimum material properties and requires a 3rd party lab certification test, spinning the flywheel to 1.5x redline for 1 hour to ensure the flywheel will not burst.
Specifically designed to work with N54 architecture clutches
Step height designed to optimize clamp load and maximize the usable range of clutch wear for a long service life
Performance:
Turner Flywheel 18.6 lbs
10 lbs lighter than the factory BMW flywheel (Stock Flywheel 28.9 lbs)
Faster revs
Improved throttle response
Improved acceleration
Sportier driving experience
Stock flywheel weight - 28.9lbs
Turner single mass flywheel weight = 18.55lbs
Single Mass Flywheel Conversion:
Audible chatter from the transmission after installation is considered normal. As with most single mass flywheels, there is less dampening in the flywheel to reduce "gear noise." This chatter noise may be more present when the transmission fluid temperatures are hotter and may be intensified by other modifications. Most gearboxes will experience some chatter noise at hotter temperatures. Please be advised that this noise will disappear once the clutch pedal is depressed. This symptom may be lessened by adjusting transmission fluid weight, turning off electrical/driveline consumers (A/C, High Beams, ETC.), and by raising the RPM slightly.
Installation:
Flywheel Hardware: For added peace of mind, apply Blue or Orange Loctite when installing factory flywheel bolts that do not come with pre-applied threadlocker.
This item fits the following BMWs with 8 bolt flywheel and build date up to 01/2009 or earlier:
2008-01/2009 E82 BMW 135i 135is 1M
2007-01/2009 E90 BMW 335i 335xi 335i xDrive - Sedan
2007-01/2009 E92 BMW 335i 335xi 335i xDrive - Coupe
2007-01/2009 E93 BMW 335i - Convertible
2008-01/2009 E60 BMW 535i 535xi 535i xDrive
This product was last offered at the strikethrough price on
06-14-2026
This product was last offered at the strikethrough price on
06-14-2026
Lightweight flywheel for quicker, effortless revs that improve throttle response and free up lost horsepower. Tested and approved by our engineering team at Turner Motorsport. Tested in early, late, ETA and IS model E30s for confirmed fitment.
Introducing our Turner Flywheel: an ingenious blend of lightweight design, rich features, and remarkable strength! Crafted from 4140 HT Steel, this flywheel is precision-machined from a solid piece, ensuring unmatched durability. By strategically trimming excess weight from its original design, we've achieved a significant reduction in weight, giving new life to your M20 engine. With upgraded efficiency, your M20 can now swiftly spin to high RPMs, unleashing the full power and prowess of this formidable engine. Our flywheel features a ring gear profile compatible with all starters, alongside a reference tab tailored for early cars equipped with bellhousing-mounted sensor crank position detection.
Do you have an early model transmission with the crank sensors on the bellhousing? Maybe you have a late 325is with the crank sensor on the front of the engine, or maybe you have a 1988 super ETA. No matter which E30 model you have, our flywheel is the perfect choice for you.
During the engineering process we encountered the full spectrum of M20 and flywheel combinations. Early cars with bellhousing crank sensors, late cars with front mounting crank sensors and even a super ETA. On this adventure we found both early and late single mass flywheels and even the dual mass that we thought for sure was just a myth. At first we were hesitant that we could make one flywheel to fit them all but with the persistence of our engineering team(fleet of E30 enthusiasts) we can proudly say our M20 flywheel does in fact fit all engine and transmission applications you can think of.
Features and benefits:
Fits early and late models with M20
Fits shallow and deep bellhousing transmissions
Ring gear suited for both starters (P# 12411726504 + 12411361874)
Heavier than other lightweight flywheels, lighter than OEM, its like the Goldie Locks of flywheels - its just right
Reference pin for bellhousing crank sensor
Strong Single-Piece 4140 HT Steel construction
Designed to be used with factory and OE clutches
Weight Comparisons:
Factory single mass flywheel EARLY (11221705046) - 23.69 lbs.
Factory single mass flywheel LATE (11221706573) - 18.74 lbs.
Dual mass flywheel (21211225979) - 27.56 lbs.
Turner flywheel - 14 lbs.
What you need:
Short bellhousing transmissions (I/IS) - Throw-out bearing P# 21517521471
Tall bellhousing transmission (ETA) - Throw-out bearing P# 21511204525
This product was last offered at the strikethrough price on
06-14-2026
This product was last offered at the strikethrough price on
06-14-2026
The factory BMW S65 dual-mass flywheel is engineered with comfort in mind, catering to the luxury-oriented expectations of the brand’s driving experience. Its design focuses on dampening drivetrain vibrations, smoothing out gear transitions, and minimizing harshness during operation. However, this refinement costs valuable performance. The dual-mass flywheel adds a substantial 27 lbs of rotational mass to the drivetrain, which significantly hinders throttle response and makes rev-matching feel sluggish and disconnected. Moreover, dual-mass flywheels are notorious for being a weak link in modified or high-performance builds and can prove costly to replace when they inevitably fail.
Our Single-Mass Lightweight Flywheel Conversion addresses all of these shortcomings with a purpose-built, lightweight, single-mass design that prioritizes performance. Weighing in at only 19 lbs., this design significantly reduces rotational mass, allowing your S65 to achieve its true motorsport potential!
Features & Benefits:
Precision machined from 4140 HT heat-treated chromoly steel for exceptional toughness, even wear properties, and increased durability.
Material quality promotes even wear across the entire friction surface, prolonging component lifespan.
Heat treated to HRC 28-32, tempered to relieve stress and improve dimensional stability.
Hardness improves component wear characteristics.
Black oxide coated for corrosion resistance on non-friction surfaces.
Precision balanced to exceed OEM specification (G16 spec to 175g-mm).
Specifically designed to work with S65 OE-architecture clutches.
Optimized step height maximizes clutch clamp load and offers a prolonged service life.
Performance:
8 lbs. lighter than the factory BMW flywheel!
OEM Dual-Mass: 27 lbs.
Turner Motorsport Single-Mass: 19 lbs.
Faster revs
Improved throttle response and acceleration
Allows for a more engaging driving experience and delivers a feeling of direct connection
Installation:
Flywheel Hardware: For added peace of mind, apply Blue or Orange Loctite when installing factory flywheel bolts that do not come with pre-applied threadlocker.
This product was last offered at the strikethrough price on
06-14-2026
This product was last offered at the strikethrough price on
06-14-2026
This product was last offered at the strikethrough price on
06-14-2026
This product was last offered at the strikethrough price on
06-14-2026
Adapt an N54 or N55 GS6-53BZ transmission to your M5x/S5x engine to unlock superior torque capacity and optimized gear ratios.
Engineered for the BMW enthusiast who demands more strength and better gear ratios, the Turner Motorsport Transmission Swap Flywheel Kit provides a direct solution for mating a modern N54 or N55 6-speed gearbox to your M20, M5X, or S5X engine. This kit bridges the gap between generations, allowing you to run a high-capacity GS6-53BZ transmission without the typical fabrication nightmares.
The technical core of this kit is our dual-geometry flywheel. By utilizing this specialized design, you can retain your engine-side stock starter while using the factory clutch and throw-out bearing from your donor transmission. This ensures a precise fit and a firm, factory-like shifting feel that can handle significantly more power than older 5-speed setups. To guarantee a fitment, we’ve included a precision drill guide for bellhousing alignment and a universal pilot bearing pin to simplify the installation process.
Features and benefits:
Compatible with the starter from your original motor.
Uses factory clutch and throwout bearing from the donor transmission (GS6-53BZ).
Comes with necessary tools and a provided drill guide to adapt the top transmission mounting holes.
Kit contents:
Swap Flywheel
Pilot bearing input adapter for late N54 and N55 GS6
Drill guide, bit, and hardware.
Flywheel bolts
Optional pilot bearing
Optional clutch
Swap notes:
Fits M20/M50/M52/S50/S52/S54 engines
Needs a custom driveshaft and rear transmission mount. (We used https://www.hdtautoparts.com/driveshafts)
For E46 only: Rear transmission mount can be used from E46 330 6 Speed. Part numbers (22316760531 & 22316760532)
Installation and Support:
Click HERE for installation instructions:
This product was last offered at the strikethrough price on
06-14-2026
This product was last offered at the strikethrough price on
06-14-2026
Turner Motorsport Lightweight N54 Flywheel & Upgraded Clutch Kit
Unlock the full potential of your N54-powered BMW with our performance-driven clutch and flywheel kit. Designed to enhance daily drivability while delivering increased power handling and improved throttle response, this kit is the ultimate upgrade for enthusiasts seeking more from their vehicle.
Why Choose This Kit?
This setup features the Turner Lightweight N54 Flywheel, precision-engineered for quicker acceleration, faster rev-matching, and a more responsive driving experience. Paired with an upgraded OE clutch from the high-performance 335is and F10 550i(V8 Bi-Turbo), this combo is capable of handling over 500 ft-lbs of torque while maintaining smooth, factory-like engagement and durability.
The factory dual-mass flywheel may prioritize smoothness and efficiency, but it comes at the cost of responsiveness and is prone to failure in high-performance applications. The Turner Lightweight Flywheel solves these issues with a single-mass design that strikes the perfect balance between comfort, performance, and reliability making it ideal for both daily driving and spirited track use.
Kit Contents:
Turner Lightweight N54 Single-Mass Flywheel (18.6 lbs, 10 lbs lighter than stock)
Upgraded OE Clutch – Supports 500 ft-lbs+
OE Clutch Fork - P# 21517564027
OE Throwout Bearing
Clutch Alignment Tool - P# 056212LA01A
Brass Clutch Fork Pivot Pin - P# 21511223328
OE Flywheel Bolts - P# 11227520706
OE Pressure Plate Screws - P# 21207548052
Pivot Pin Retaining Spring - P# 21517570284
Transmission Mating Dowels - P# 11117524470
Flywheel Features:
Precision-machined 4140 HT heat-treated chromoly steel for durability
Black oxide coating to resist corrosion
8620 steel pilot bearing pin for maximum wear resistance
Precision balanced to exceed OEM standards
Optimized step height for longer clutch life and consistent performance
Clutch:
Upgrade for 135i/335i/535i models from the 335is! Featuring a heavy-duty clutch with more holding power and a stock-like pedal feel. Excellent solution for If your clutch is slipping, or the engagement isn't what it used to be, it's time for a replacement. Slipping clutches won't allow your BMW to accelerate properly and can pose problems under a load such as going up large inclines. Also, a worn clutch can cause less precise and engaging shifts. By replacing your clutch you will restore performance and driving pleasure.
This clutch is an excellent upgrade for non 335is/550i/650i models. It features a more heavy-duty clutch disc and more holding power with stock-like pedal effort.
Transform your driving experience with this Turner Motorsport clutch and flywheel kit - engineered for power, performance, and everyday reliability.
MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.
MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.
This product was last offered at the strikethrough price on
05-03-2026
This product was last offered at the strikethrough price on
05-03-2026
Turner Motorsport Lightweight N55 Flywheel & Upgraded Clutch Kit
Unlock the full potential of your N55-powered BMW with our performance-driven clutch and flywheel kit. Designed to enhance daily drivability while delivering increased power handling and improved throttle response, this kit is the ultimate upgrade for enthusiasts seeking more from their vehicle.
Why Choose This Kit?
This setup features the Turner Lightweight N55 Flywheel, precision-engineered for quicker acceleration, faster rev-matching, and a more responsive driving experience. Paired with an upgraded OE clutch from the high-performance 335is and F10 550i(V8 Bi-Turbo), this combo is capable of handling over 500 ft-lbs of torque while maintaining smooth, factory-like engagement and durability.
The factory dual-mass flywheel may prioritize smoothness and efficiency, but it comes at the cost of responsiveness and is prone to failure in high-performance applications. The Turner Lightweight Flywheel solves these issues with a single-mass design that strikes the perfect balance between comfort, performance, and reliability making it ideal for both daily driving and spirited track use.
Kit Contents:
Turner Lightweight N55 Single-Mass Flywheel (18.6 lbs, 10 lbs lighter than stock)
Upgraded OE Clutch – Supports 500 ft-lbs+
OE Clutch Fork - P# 21517564027
OE Throwout Bearing
Brass Clutch Fork Pivot Pin - P# 21511223328
OE Flywheel Bolts - P# 11227520706
OE Pressure Plate Screws - P# 21207548052
Pivot Pin Retaining Spring - P# 21517570284
Transmission Mating Dowels - P# 11117524470
Flywheel Features:
Precision-machined 4140 HT heat-treated chromoly steel for durability
Black oxide coating to resist corrosion
Precision balanced to exceed OEM standards
Optimized step height for longer clutch life and consistent performance
Clutch:
Upgrade for 135i/335i/535i models from the 335is! Featuring a heavy-duty clutch with more holding power and a stock-like pedal feel. Excellent solution for If your clutch is slipping, or the engagement isn't what it used to be, it's time for a replacement. Slipping clutches won't allow your BMW to accelerate properly and can pose problems under a load such as going up large inclines. Also, a worn clutch can cause less precise and engaging shifts. By replacing your clutch you will restore performance and driving pleasure.
This clutch is an excellent upgrade for non 335is/550i/650i models. It features a more heavy-duty clutch disc and more holding power with stock-like pedal effort.
Transform your driving experience with this Turner Motorsport clutch and flywheel kit - engineered for power, performance, and everyday reliability.
This product was last offered at the strikethrough price on
06-13-2026
This product was last offered at the strikethrough price on
06-13-2026
Lightweight flywheels have proven themselves to be a worthwhile performance enhancement. But with the quicker throttle response and horsepower improvement comes one serious drawback: flywheel chatter. Without the dual-mass flywheel's rubber isolators, a lightweight aluminum flywheel has more rattle than stock. ECS has designed this flywheel using chrom-moly steel and it weighs almost ten pounds less than the stock DMF but not as extreme as full aluminum flywheels. The steel helps dampen vibration and noise so you get near-factory refinement and most of the benefits of a lightweight flywheel: quicker throttle response, better reliability, and more power to the wheels. Zero-balanced and SFI 1.1 certified (material and design has been independently burst tested to ensure quality and safety). This flywheel requires the E34 M5 sprung hub clutch kit. Choose below from the flywheel only or a complete kit.
Modern flywheels are built with additional components that are designed to dampen and minimize vibrations from the engine and transmission. Weight has increased and reliability has decreased. With additional weight more energy is required for it to move. A lightweight flywheel does away with the dual mass design and its additional mass so more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance. And with a single-mass flywheel the unreliable DMF design is eliminated.
Stock flywheel weight - 25.0lbs
ECS flywheel weight = 16.55lbs
This item fits the following BMWs:
1992-1999 E36 BMW 323is 323ic 325i 325is 325ic 328i 328is 328ic M3
1999-2002 E46 BMW 323i 323ci 325i 325ci 328i 328ci 330i 330ci (5-speed)
1997-2002 Z3 BMW Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i M Roadster M Coupe
2003-2005 E85 BMW Z4 2.5i Z4 3.0i (5-speed)
The ACT Streetlite flywheel offers the following benefits:
Noticeably improved engine response and acceleration: Experience a significant boost in engine performance and acceleration with this component. OE to mild gear rattle: Expect only minimal gear rattle, from Original Equipment (OE) standards to a mild level, ensuring a smoother drive. Heat-treated forging for strength and toughness: Crafted using heat-treated forging, this part guarantees enhanced strength and durability. Induction-hardened ring gears for maximum life: The ring gears undergo induction hardening, providing maximum lifespan and reliability. One-piece construction allows less opportunity for failure and provides uniform efficient heat transfer from the clutch disc: The one-piece design reduces potential failure points and ensures uniform and efficient heat transfer from the clutch disc, preventing issues like warped inserts or loose ring gears. Recommended for street and race use: This component is ideal for both everyday street driving and competitive racing environments.
Forged, CNC machined, and dynamically computer balanced for smooth high RPM reliability: Expertly forged, CNC machined, and dynamically balanced via computer to ensure smooth and reliable performance at high RPMs.
This product was last offered at the strikethrough price on
06-14-2026
This product was last offered at the strikethrough price on
06-14-2026
The factory dual-mass flywheel in your MINI N14 was built with comfort in mind—absorbing drivetrain vibrations and smoothing shifts—but at the cost of performance. Weighing in at a hefty 28.3 lbs., the OEM flywheel adds excessive rotational mass, dulling throttle response, slowing acceleration, and complicating precise rev-matching. Worse yet, it's known to be unreliable in modified or tuned setups and expensive to replace when it fails.
This single-mass design from ECS Tuning weighs just 18.8 lbs. It cuts nearly 10 lbs. of rotational weight to significantly enhance throttle response, acceleration, and overall driving feel. Built for durability and spirited driving, it's the ultimate upgrade for enthusiasts who want to make the most of every gear change.
Key Features:
Precision CNC-machined from 4140 HT Chromoly Steel: Ensures outstanding toughness, consistent wear, and long-term durability.
Heat Treated and Tempered: Achieves HRC 28-32 for improved strength, stress relief, and dimensional stability—even at elevated temperatures.
Black Oxide Coated: Resists corrosion for long-lasting protection and a professional finish.
Precision Balanced: Exceeds OEM standards (G16, 175 g-mm) to ensure smooth, safe operation at all RPMs.
SFI 1.1 Certified: Tested and approved for extreme use—track or street.
Direct Fit for OE N14 Clutch Kits: Maintains compatibility with factory-style components for hassle-free installation.
Performance Benefits:
Substantial Weight Reduction
OEM Flywheel: 28.3 lbs.
ECS Lightweight Flywheel: 18.8 lbs.
Net Savings: Nearly 10 lbs.
Faster Revving and Sharper Throttle Response: Reducing rotational mass translates into a more dynamic and responsive driving experience.
Improved Clutch Engagement and Longevity: Optimized step height delivers better clamp load and extends service life.
Ideal for Modified MINIs: Built to handle increased power and spirited driving with confidence.
Replaces MINI OEM Part #: 21207575069
MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.
MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.
This product was last offered at the strikethrough price on
06-08-2026
This product was last offered at the strikethrough price on
06-08-2026
BMW E36 328i, Z3 2.8 JB Racing Lightweight Aluminum Flywheel offers a significant performance upgrade by replacing the heavy stock steel flywheel with a much lighter aluminum version. This JB Racing flywheel is designed to deliver faster acceleration, improved throttle response, and enhanced overall performance for your BMW.
The modern stock flywheels are burdened with additional components meant to dampen vibrations, which unfortunately adds unnecessary weight. The JB Racing aluminum flywheel, weighing just 10.0 lbs compared to the stock 25.0 lbs, eliminates this excess mass, allowing more power to reach the wheels and reducing the energy wasted on spinning the flywheel. Engine builders prioritize lightweight flywheels when optimizing race engines for maximum efficiency, and the difference is especially noticeable in how quickly the engine revs and reaches its power band.
This JB Racing lightweight flywheel is a direct replacement for the stock flywheel and is compatible with the factory BMW organic clutch. This compatibility ensures that you can use standard replacement clutches, making maintenance simple and cost-effective. The flywheel can also be resurfaced for a fresh contact surface, so there’s no need to buy a new one when it’s time to replace the clutch.
While single-mass aluminum flywheels like this one may result in slightly more noise and vibration compared to dual-mass designs, this can be managed with heavier transmission oil and sprung hub clutches, such as the Sachs Performance clutch available through Turner Motorsport.
Vehicle Compatibility:
SPEC billet flywheels offer precise engineering tailored to specific driving environments, ensuring optimal performance for each vehicle. Made from high-quality steel and aluminum, SPEC flywheels boast a .001 machine tolerance, guaranteeing a flat seating surface for the clutch and smooth rotational qualities. These flywheels are essential for converting OE Dual Mass to Single Mass for compatibility with Spec Design clutch Kits.
BMW E60 E9X XACT Flywheel Streetlite is an advanced performance flywheel engineered to offer substantial improvements over stock components. This lightweight flywheel is designed for durability and enhanced performance, making it an excellent choice for both street driving and drag racing.
Upgrade your BMW with the BMW E60 E9X XACT Flywheel Streetlite for enhanced performance and durability.
This product was last offered at the strikethrough price on
05-07-2026
BMW E36 M3 Z3 XACT Flywheel Streetlite is a high-performance upgrade designed to enhance engine response and acceleration. This Streetlite flywheel is significantly lighter than the stock flywheel, offering superior durability and strength. Crafted from Chromoly Steel, it provides excellent heat tolerance and rigidity, making it ideal for both street and drag racing applications.
Specifications:
MINI R52 R53 Lightweight Aluminum Flywheel (12lbs) enhances the performance of the MINI with its precision engineering and lightweight design. This flywheel, manufactured by SPEC, is tailored for specific driving environments, making it ideal for both daily driving and high-performance applications.
MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.
MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.
This is the stock twin mass flywheel for the N55 engine used in the E82 135i, E9X 335, F3x 335/435, and F10 535i. It's manufactured by OEM supplier LuK. Sachs recommends a new dual mass flywheel (DMF) on every other clutch replacement. There are several indicators for replacing the flywheel: damage to the clutch contact plate (from a severely worn clutch disc), grease leaking from inside (overheating), build-up of clutch material on the contact plate (excessive slipping and overheating), and failure of the internal damping system.
The dampening system uses rubber or coil springs to absorb driveline vibrations. Through age, excessive heat, and aggressive use the rubber loses its resilience and the metal springs lose their strength and become brittle. If the clutch and flywheel have become overheated the internal grease may break down as well. A DMF failure can be massive and catastrophic, not to mention dangerous as bits of metal and rubber fling themselves through the transmission bellhousing. Heat and aggressive driving will accelerate the wear so race and track cars should have their stock flywheels replaced at regular intervals or with any new clutch. Even normal street cars should plan for a new flywheel if it has high mileage.
DMF wear can only be checked with the transmission and clutch removed. If you can rotate the outer flywheel more than 20mm in either direction then it should be replaced.
A new pilot bearing (roller bearing) is included, pre-installed in the flywheel hub.
This item fits the following BMWs with the single turbo N55 engine and manual transmission:
2011-2012 E82 BMW 135i
2011 E90 BMW 335i 335xi 335i xDrive - Sedan
2011-2013 E92 BMW 335i 335xi 335i xDrive - Coupe
2011-2013 E93 BMW 335i - Convertible
2012-2015 F30 BMW 335i 335iX - Sedan
2014-2016 F34 BMW 335iX - Gran Turismo
2014-2016 F32 BMW 435i 435iX - Coupe
2014-2016 F33 BMW 435i 435iX - Convertible
2014-2016 F36 BMW 435i 435iX - Gran Coupe
2011+ F10 BMW 535i 535i xDrive
MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.
MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.
MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.
MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.
