BMW Suspension Parts

Rear Shock Mounts (RSM) - Upper - OEM Rubber - E82, E9X (non-M) (Pair...

T#:11986

Part#: E9X-URSM

In Stock

Sale - Save 2% $ 49.12

This product was last offered at the strikethrough price on
05-03-2026

$ 48.01 USD

Add to Wish List

Qty

Sale - Save 2%

$ 49.12

This product was last offered at the strikethrough price on
05-03-2026

$ 48.01 USD

Add to Wish List

A 4-piece set of new OEM rear upper and lower shock mounts to complete your shock install or replace broken mounts (RSM). The top mounts on the shocks for the E82 and E90/E91/E92/E93 consist of 4 pieces. These E9X URSM pieces fit all E82 and E9X except the M3 with EDC.

Rear Shock Mount (RSM) Kit consists of:
A. rear upper-top shock mounts, 33506771737
B. rear upper-middle shock mounts, 33506767010
C. rear upper-bottom shock mounts, 33506771738
D. rear upper supporting cup, 33526764418 (sits over bumpstop)
There is also a lower mount that is available separately. This package covers only the rear upper shock mounts.

That's a lot of rubber that takes constant deflecting and absorbing of cornering forces and impacts from bumps, potholes, etc. Replacing the RSMs is key to maintaining a quiet and comfortable ride. Price is for all 4 upper pieces for BOTH sides of the car.

This item fits the following BMWs:
2006-2011 E90 BMW 325i 325xi 328i 328xi 328i xDrive 330i 330xi 335d 335i 335xi 335i xDrive - Sedan
2006-2011 E91 BMW 325xi 328i 328xi 328i xDrive - Wagon
2007-2012 E92 BMW 328i 328xi 328i xDrive 335i 335is 335xi 335i xDrive - Coupe
2007-2012 E93 BMW 328i 335i - Convertible

Show More Show Less

KMAC Stage 1 Street Front Adjustable Camber/Caster Plates - E36, E39 ...

T#:389645

Part#: 192416-1J

In Stock

$ 380.00 USD

Add to Wish List

Qty

$ 380.00 USD

Add to Wish List

Location: Front
Type: Street, Stage 1
Bearing: captive-ball fully encased in polyurethane

These front adjustable camber/caster plates will replace your stock front upper strut bearing. The KMAC plates are a 'floating' design so camber and caster are adjusted together. This design allows maximum range of adjustment since no other hardware interferes with the adjustments. Since these replace your stock strut bearings they are designed to work with a stock-type spring only. And when installed correctly will not significantly alter ride height. Adjustment is easily done by loosening the three nuts on top of the tower and sliding the camber plate into the position you want, then re-tighten the nuts. These mounts can be installed two ways - for camber correction or swapped side-side for increasing negative camber. Detailed instructions included.

Note: suspensions vary from manufacturer to manufacturer. Turner Motorsport cannot be responsible for fitment issues caused by non-stock or specialized coil-over suspensions. As with any race-derived component, additonal fabrication may be required.

This item fits the following BMWs:
2008-2012 E82 BMW 128i 135i
6/1992-1999 E36 BMW 318i 318is 318ti 318ic 323is 323ic 325i 325is 325ic 328i 328is 328ic M3
1999-2005 E46 BMW 323i 323ci 325i 325ci 325xi 328i 328ci 330i 330ci 330xi
2006-2011 E90 BMW 325i 328i 330i 335d 335i - Sedan
2006-2012 E91 BMW 328i - Wagon
2007-2013 E92 BMW 328i 335i 335is - Coupe
2007-2013 E93 BMW 328i 335i - Convertible
1997-2003 E39 BMW 525i 528i 530i 540i (not for cars with EDC)
2004-2010 E60 BMW 525i 530i 528i 535i 545i 550i
2004-2011 E63 E64 BMW 645ci 650i
1997-2002 Z3 BMW Z3 1.9 Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i M Roadster M Coupe
2003-2008 E85 BMW Z4 2.5i Z4 3.0i Z4 3.0si
2009+ Z4 BMW Z4 sDrive28i Z4 sDrive30i Z4 sDrive35i Z4 sDrive35is
2000-2003 E52 BMW Z8 Roadster (without EDC)

Show More Show Less

Bav Auto Trailing Arm Bushing and Ball Joint Tool - Master Set ...

T#:580410

Part#: B8800100

In Stock

Sale - Save 3% $ 222.99

This product was last offered at the strikethrough price on
05-03-2026

$ 216.30 USD

Add to Wish List

Qty

Sale - Save 3%

$ 222.99

This product was last offered at the strikethrough price on
05-03-2026

$ 216.30 USD

Add to Wish List

Remove and install the three bushings and ball joints that are pressed into the rear trailing arm. Use this one tool kit for on-vehicle or off-vehicle removal and replacement of the Rear Trailing Arm Bushing, Outer Upper Control Arm Bushing (ball joint) and Outer Lower Control Arm Bushing (ball joint). This tool is designed to work on E36 3-series (except E36 318ti), E46 3-series, E83 X3 and E85/E86 Z4 Coupe & Roadster.

From 1974 to 2019, Bavarian Autosport was one of the premier vendors for BMW and MINI auto parts. We are happy to preserve the Bav Auto legacy by continuing to carry their high-quality products into the future. All Bav Auto parts will remain unchanged in design and sourced from the same OEM suppliers to ensure long-lasting reliability. We trust these parts, accessories, and upgrades so confidently that we back every Bavarian Autosport branded component with a 2-year warranty.

Show More Show Less

Rear Subframe Bushings/Mount Set - Rubber - E46 M3, Z4 M

T#:2051

Part#: TMS2051

In Stock

$ 291.99 USD

Add to Wish List

Qty

$ 291.99 USD

Add to Wish List

Any subframe work or reinforcement project on the rear of the E46 M3 should include a new set of subframe mounts. It's the worn rubber bushings that contribute to failed rear subframes on the E46 (but not the only reason). As the rubber gets worn, there is more flex to the mount. This flexing is then transferred to the sheetmetal in the floor where the spot welds will pop and the sheetmetal will crack. Additional force coming from stiffer suspensions and stickier tires will only increase the flexing of the mounts/chassis.

Of course, stiffer mounts would help prevent this problem but with a stiffer bushing comes ride harshness, vibration, and additional noise. Our engineers and technicians recommend replacement with the factory rubber bushings (along with the appropriate reinforcement of the floor). The rubber bushings help isolate bumps and impacts and are quiet. They are also a perfect fitment and require no maintenance.

This item is a set of 4 Original BMW rubber subframe mounts. Individual part numbers - 33 31 2 283 573 (left front), 33 31 2 283 574 (right front), and 33 31 2 283 419 (left and right rear, x 2).

Applications:
2001-2006 E46 M3, M3 CSL coupe, convertible
2007-up Z4 M Roadster, M Coupe

Show More Show Less

KMAC Adjustable Rear Camber And Toe Bushings Set - E82, E89, E9X non-...

T#:389667

Part#: 193926K

In Stock

13% off MSRP $ 480.00

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 417.00 USD

Limited Qty Sale

Add to Wish List

Qty

13% off MSRP

$ 480.00

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 417.00 USD

Limited Qty Sale

Add to Wish List

Rear adjustable camber and toe bushings for the E82/E9X non-M 3-series. These bushings allow you to adjust camber and toe beyond factory specs to either restore camber or add more. If you lowered your car and have too much camber these bushings can get you back to stock specs. On the flip side if you need more camber for the track or autocross, you can fine tune it with these too. These bushings press in and replace the existing rubber bushings. They are made from peformance urethane which will give more feedback and response to the driver. Sold as a set with a bushing extraction tool included.

Fits the following BMWs:
E82/88 BMW 2 Series
E89 BMW Z4
E9X BMW Non-M

Show More Show Less

KMAC Stage 1 Street Front Adjustable Camber/Caster Plates - E39 540/M...

T#:389661

Part#: 193616-1J

Ships on Sep 11, 2026

$ 380.00 USD

Add to Wish List

Qty

$ 380.00 USD

Add to Wish List

Location: Front
Type: Street, Stage 1
Bearing: captive-ball fully encased in polyurethane

These front adjustable camber/caster plates will replace your stock front upper strut bearing. The KMAC plates are a 'floating' design so camber and caster are adjusted together. This design allows maximum range of adjustment since no other hardware interferes with the adjustments. Since these replace your stock strut bearings they are designed to work with a stock-type spring only. And when installed correctly will not significantly alter ride height. Adjustment is easily done by loosening the three nuts on top of the tower and sliding the camber plate into the position you want, then re-tighten the nuts. These mounts can be installed two ways - for camber correction or swapped side-side for increasing negative camber. Detailed instructions included.

Note: suspensions vary from manufacturer to manufacturer. Turner Motorsport cannot be responsible for fitment issues caused by non-stock or specialized coil-over suspensions. As with any race-derived component, additonal fabrication may be required.

This item fits the following BMWs:
1997-2003 E39 BMW 525i 528i 530i 540i (for cars with EDC)
1999-2003 E39 BMW M5
1995-2001 E38 BMW 740i 740il 750il (for cars with EDC)

Show More Show Less

Bav Auto Rear Subframe Bushing Press - E88 E9X BMW

T#:580432

Part#: B8800127

In Stock

Sale - Save 3% $ 419.99

This product was last offered at the strikethrough price on
05-03-2026

$ 407.39 USD

Add to Wish List

Qty

Sale - Save 3%

$ 419.99

This product was last offered at the strikethrough price on
05-03-2026

$ 407.39 USD

Add to Wish List

The Bav Auto Rear Subframe Bushing Press allows you to remove and install rear subframe bushings while the subframe is still in the vehicle, saving you several hours of labor.

Adjustable Rear Upper/Inner Camber Bushings

T#:600206

Part#: 193926-3H

Ships on Sep 11, 2026

$ 320.00 USD

Add to Wish List

Qty

$ 320.00 USD

Add to Wish List

Nearly every car manufactured in the modern era carries a dark secret – fully-adjustable suspension has been all but eliminated in the name of cost-cutting and assembly-line efficiency. What this means for you is increased tire wear and more frequent replacement, as a “full alignment” consists only of rudimentary toe-angle adjustment. For over forty years, K-MAC has been hard at work developing a solution to this problem with patented innovations in camber/caster plates and bushing kits, allowing easy adjustment and a true “full four-wheel alignment” to be performed by any competent shop. These bushings make camber adjustments possible for the first time, and improve the ability to complete toe angle adjustments. When used in conjunction with the K-MAC Camber and Toe kit and Rear Adjustable Trailing Arms allows full adjustability of the 5 multi-link rear arms and positive location. Bolt-on installation – insertion/extraction tube included! Easily adjusted on the car with basic hand tools Unique failsafe locking hardware – set & forget! High quality elastomer compound resists binding Hardened & nickel-chrome plated centers for maximum bushing life 2x the load area of stock bushings Spiral grease grooves

Show More Show Less

K-MAC Stage 1 Street - Front Adjustable Camber/Caster Plates ...

T#:388807

Part#: 195116-1J

Ships on Sep 11, 2026

$ 380.00 USD

Add to Wish List

Qty

$ 380.00 USD

Add to Wish List

Location: Front
Type: Street, Stage 1
Bearing: captive-ball fully encased in polyurethane

These front adjustable camber/caster plates will replace your stock front upper strut bearing. The KMAC plates are a 'floating' design so camber and caster are adjusted together. This design allows maximum range of adjustment since no other hardware interferes with the adjustments. Since these replace your stock strut bearings they are designed to work with a stock-type spring only. And when installed correctly will not significantly alter ride height. Adjustment is easily done by loosening the three nuts on top of the tower and sliding the camber plate into the position you want, then re-tighten the nuts. These mounts can be installed two ways - for camber correction or swapped side-side for increasing negative camber. Detailed instructions included.

Note: suspensions vary from manufacturer to manufacturer. Turner Motorsport cannot be responsible for fitment issues caused by non-stock or specialized coil-over suspensions. As with any race-derived component, additonal fabrication may be required.

This item fits the following BMWs:
3/2002-2006 R50 MINI MINI Cooper
2005-2008 R52 MINI MINI Cooper Convertible, MINI Cooper S Convertible.
3/2002-2006 R53 MINI MINI Cooper S

Show More Show Less

BMW Motorsport Rear Sway Bar Bushing - 14-15mm - E90 E92 E82 ...

T#:3213

Part#: 33558300883

Ships on Sep 17, 2026

$ 31.99 USD

Add to Wish List

Qty

$ 31.99 USD

Add to Wish List

This is the factory BMW Motorsport Group N high performance rear sway bar / swaybar bushing for cars with a 14/15mm sway bar. This heavy duty rubber bushing is stiffer than the stock bushing to improve handling. They are great for track use - and Grand Am Cup legal! - yet can also be used on a street driven car - please note these will not be as compliant as the stock rubber bushing.

Sold Individually

This item fits the following BMWs:
2008+ E82 BMW 128i 135i
2006+ E90 BMW 325i 328i 330i 335i
2007+ E92 BMW 328i 335i 335is
2007+ E93 BMW 328i 335i

Show More Show Less

Rear Subframe Bushings/Mounts - Set - Group N Race Rubber - E82, E9X ...

T#:12076

Part#: E9X-GPN-SUBFRAME

In Stock

$ 800.00 USD

Add to Wish List

Qty

$ 800.00 USD

Add to Wish List

The E82 and E90/E92 subframes have an inherent weakness in the rear subframe - the mounts are too soft for the power and torque these cars are capable of. The subframe is the heart of a BMW's rear suspension. As torque is transmitted through the differential and axles and as the tires grip the road, the subframe mounts are working to keeping everything in line. That's a tough task to hold when torque is increased with bigger boost (335i) or even mild tweaks (M3). While the M3 subframe mounts are a great upgrade for the non-M chassis these factory BMW Motorsport subframe mounts go one step further.

These Motorsport/Group N rear subframe bushings are a direct replacement upgrade over the stock mounts. They are rubber to conform to the rules of the Group N racing class - so they are still acceptable for street use as long as extra ride harshness can be tolerated. The rear subframe has to come down from the car for these mounts to be pressed in. So now is the perfect time to do other work as well - check out our other Motorsport Race bushings or M3 upgrades.

Price is for the set of 4 mounts.

This item fits the following BMWs:
2008-2012 E82 BMW 128i 135i 1M Coupe
2006-2011 E90 BMW 325i 325xi 328i 328xi 328i xDrive 330i 330xi 335d 335i 335xi 335i xDrive M3 - Sedan
2006-2012 E91 BMW 325xi 328i 328xi 328i xDrive - Wagon
2007-2013 E92 BMW 328i 328xi 328i xDrive 335i 335is 335xi 335i xDrive M3 - Coupe
2007-2013 E93 BMW 328i 335i M3 - Convertible

Show More Show Less

KMAC Stage 1 Street Front Adjustable Camber/Caster Plates - E24, E28,...

T#:389654

Part#: 193316-1J

Special Order: No Guaranteed ETA

$ 379.99 USD

Add to Wish List

Qty

$ 379.99 USD

Add to Wish List

Location: Front
Type: Street, Stage 1
Bearing: captive-ball fully encased in polyurethane

These front adjustable camber/caster plates will replace your stock front upper strut bearing. The KMAC plates are a 'floating' design so camber and caster are adjusted together. This design allows maximum range of adjustment since no other hardware interferes with the adjustments. Since these replace your stock strut bearings they are designed to work with a stock-type spring only. And when installed correctly will not significantly alter ride height. Adjustment is easily done by loosening the three nuts on top of the tower and sliding the camber plate into the position you want, then re-tighten the nuts. These mounts can be installed two ways - for camber correction or swapped side-side for increasing negative camber. Detailed instructions included.

Note: suspensions vary from manufacturer to manufacturer. Turner Motorsport cannot be responsible for fitment issues caused by non-stock or specialized coil-over suspensions. As with any race-derived component, additonal fabrication may be required.

This item fits the following BMWs:
1984-1991 E30 BMW 318i 318is 318ic 325e 325es 325i 325ic 325is M3
1982-1988 E28 BMW 528e 533i 535i 535is M5
1993-1995 E34 BMW 525i
1982-1989 E24 BMW 633csi 635csi M6

Show More Show Less

Bav Auto Rear Subframe Bushing Press Tool

T#:580407

Part#: B8800097

In Stock

Sale - Save 3% $ 383.99

This product was last offered at the strikethrough price on
05-03-2026

$ 372.47 USD

Add to Wish List

Qty

Sale - Save 3%

$ 383.99

This product was last offered at the strikethrough price on
05-03-2026

$ 372.47 USD

Add to Wish List

Allows you to both remove and install rear subframe to body bushings without removing your subframe, saving you hours of labor from having to disassemble suspension components.

Front Upper Control Arm Bushing Set (FCAB) - Group N Race Rubber - E8...

T#:2309

Part#: E9X-GPN-UCAB

Ships in 7 Business Days

$ 413.38 USD

Add to Wish List

Qty

$ 413.38 USD

Add to Wish List

These are the factory BMW Motorsport Group N high performance front upper control arm bushings. These heavy duty rubber bushings are stiffer than the stock bushings to improve steering feel and improve handling. They are great for track use - and Grand Am Cup legal! - yet can also be used on a street driven car - please note these will not be as compliant as the stock rubber bushings. These are for the control arm with the ball joint pointing down, sometimes referred to as the thrust arm or tension strut.

Price is for the pair of bushings.

This item fits the following BMWs:
2008-2012 E82 BMW 128i 135i 1M
2006-2011 E90 BMW 325i 328i 330i 335d 335i M3 - Sedan
2006-2011 E91 BMW 328i - Wagon
2007-2012 E92 BMW 328i 335i 335is M3 - Coupe
2007-2012 E93 BMW 328i 335i M3 - Convertible

Show More Show Less

Adjustable Rear Camber/Toe Bushings

T#:582353

Part#: 192026G

In Stock

$ 320.00 USD

Add to Wish List

Qty

$ 320.00 USD

Add to Wish List

KMAC Stage 2 Street/Track Front Adjustable Camber/Caster Plates - F22...

T#:389642

Part#: 192616-2N

Special Order: No Guaranteed ETA

$ 695.00 USD

Add to Wish List

Qty

$ 695.00 USD

Add to Wish List

Location: Front
Type: Street/Track, Stage 2
Upper spring perch: OEM-size, 60mm, and 2.5" included
Bearings: urethane OEM-type center bushing; lubricated radial thrust bearing on spring perch

KMAC camber/caster plates use a patented adjustment method designed for easy and rapid alignment adjustments. The KMAC design has a 'floating' inner camber plate, rather than slotted, to allow camber and caster to be adjusted together. To adjust, simply loosen the top three nuts on the strut tower and position the KMAC mount to match your desired alignment settings. The KMAC design allows more camber and caster adjustment because separate caster hardware is eliminated. While primarily designed to increase negative camber for track use these can also be used to fix alignment issues that cause uneven tire wear or unwanted handling behavior.

KMAC camber kits are the most complete kits on the market, with all of the common spring perch options and strut hardware included. The OEM size spring perch as well as 60mm and 2.5" spring isolators are included which makes it easy to upgrade from stock struts to coil overs without having to buy new camber plates. Or swap springs on your coil overs between 60mm and 2.5" without buying additional upper perches. Also included are the most common strut pin hardware - 14mm lower bearing adapters and 12x1.5, 12x1.75, and 14x1.5 top nuts. This takes the guesswork out of ordering the correct hardware for your strut type. The urethane main bushing is also replaceable and the camber plate parts are made from 7075-grade aluminum for a lifetime of camber plate use.

Fitment Note 1: replaces factory BMW strut mount with 3 mounting bolts (up to 12/2014 prodution). Not for cars with 5-bolt strut mounts.

Fitment Note 2: suspensions vary from manufacturer to manufacturer. The proper stacked height and clearances are required. K-MAC includes bearing adapters, spacers, and various top nuts but it is still the responsibility of the installer to ensure a correct and safe fitment. Basic instructions are included but professional installation is required. As with any race-derived component, additonal fabrication may be required.

This item fits the following BMWs:
-12/2014 F22 BMW 228i 228i xDrive M235i M235i xDrive
2012-12/2014 F30 BMW 320i 320i xDrive 328d 328d xDrive 328i 328i xDrive 335i 335i xDrive - Sedan
2013-12/2014 F31 BMW 328i xDrive 328d xDrive - Wagon
-12/2014 F34 BMW 328i xDrive GT, 335i xDrive GT - Gran Tourismo
2013-12/2014 F32 BMW 428i 428i xDrive 435i 435i xDrive - Coupe
2013-12/2014 F33 BMW 428i Convertible 428i xDrive Convertible 435i Convertible - Convertible
-12/2014 F36 BMW 428i Gran Coupe 428i xDrive Gran Coupe 435i Gran Coupe 435i xDrive Gran Coupe
Not for cars with Adaptive M Suspension option code S2VFA

Show More Show Less

KMAC Street Rear Adjustable Camber/Toe Bushings - E60 E63 E65 E53 X5 ...

T#:389668

Part#: 193726J

Special Order: No Guaranteed ETA

$ 380.00 USD

Add to Wish List

Qty

$ 380.00 USD

Add to Wish List

Perfect for lowered cars that need to dial out negative camber to preserve tires. Also perfect for track cars - easily dial in toe and camber for the track for better handling. Priced per set. Fits BMW E60 E63 E65.

This item fits the following BMWs:
2004-2010 E60 BMW 525i 525xi 528i 528xi 530i 530xi 535i 535xi 545i 550i M5
2004+ E63 BMW 645ci 650i M6
2002-2008 E65 BMW 745i 745li 750i 750li 760i 760li
2000-2006 E53 BMW X5 3.0i, X5 4.4i, X5 4.6is, X5 4.8is

Show More Show Less

KMAC Stage 3 Street/Track Front Adjustable Camber/Caster Plates - E36...

T#:389646

Part#: 192416-3L

Special Order: No Guaranteed ETA

$ 545.00 USD

Add to Wish List

Qty

$ 545.00 USD

Add to Wish List

Location: Front
Type: Street/Track, Stage 2
Bearings: main PTFE-lined pillow-ball bearing suspended in polyurethane; self-lubricating radial axial bearing/bushing in upper spring plate
Springs: includes OEM size upper spring perch, 60mm upper spring perch, and 2.5" upper spring perch

The Stage 3 KMAC plates are a mixed track and street camber/caster plate meant to be used in a variety of suspensions and setups. Since there is less bushing than on the Stage 1, more noise and vibration will reach the driver. The adjustment design is similar to the Stage 1 with a floating mount that sets camber and caster simultaneously. This design allows maximum range of adjustment since no other hardware interferes with the adjustments. These plates can work on both coil over and stock-stype suspensions and upper spring perches are included for OEM springs, 60mm, and 2.5" coil over springs. The upper perch assembly incorporate a self-sliding radial bushing that allows the spring to spin during its travel instead of bind. This reduces tension on the spring and helps reduce noise and spring 'popping' noises. Bearing inserts, spacers for correct articulating angles, and 3 sizes of upper nut adapters included. The urethane bushings and bearings are replaceable if they wear out. These are designed mainly for adding negative camber for improved handling and not for camber correction back to stock settings (see Stage 1 kit). Basic instructions included but professional installation is required.

Note: suspensions vary from manufacturer to manufacturer. The proper stacked height and clearances are required. K-Mac includes bearing adapters, spacers, and various top nuts but it is still the responsibility of the installer to ensure a correct and safe fitment. As with any race-derived component, additonal fabrication may be required.

This item fits the following BMWs:
2008-2012 E82 BMW 128i 135i
6/1992-1999 E36 BMW 318i 318is 318ti 318ic 323is 323ic 325i 325is 325ic 328i 328is 328ic M3
1999-2005 E46 BMW 323i 323ci 325i 325ci 325xi 328i 328ci 330i 330ci 330xi
2006-2011 E90 BMW 325i 328i 330i 335d 335i - Sedan
2006-2012 E91 BMW 328i - Wagon
2007-2013 E92 BMW 328i 335i 335is - Coupe
2007-2013 E93 BMW 328i 335i - Convertible
1997-2003 E39 BMW 525i 528i 530i 540i (not for cars with EDC)
2004-2010 E60 BMW 525i 530i 528i 535i 545i 550i
2004-2011 E63 E64 BMW 645ci 650i
1997-2002 Z3 BMW Z3 1.9 Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i M Roadster M Coupe
2003-2008 E85 BMW Z4 2.5i Z4 3.0i Z4 3.0si
2009+ Z4 BMW Z4 sDrive28i Z4 sDrive30i Z4 sDrive35i Z4 sDrive35is
2000-2003 E52 BMW Z8 Roadster (without EDC)

Show More Show Less

KMAC Stage 2 Street/Track Front Adjustable Camber/Caster Plates - E36...

T#:389647

Part#: 192416-2L

Ships in 9 Business Days

$ 545.00 USD

Add to Wish List

Qty

$ 545.00 USD

Add to Wish List

Location: Front
Type: Street/Track, Stage 2
Bearings: main PTFE-lined pillow-ball bearing suspended in polyurethane; self-lubricating radial axial bearing/bushing in upper spring plate
Springs: includes OEM size upper spring perch, 60mm upper spring perch, and 2.5" upper spring perch

The Stage 2 KMAC plates are a mixed track and street camber/caster plate meant to be used in a variety of suspensions and setups. Since there is less bushing than on the Stage 1, more noise and vibration will reach the driver. The adjustment design is similar to the Stage 1 with a floating mount that sets camber and caster simultaneously. This design allows maximum range of adjustment since no other hardware interferes with the adjustments. These plates can work on both coil over and stock-stype suspensions and upper spring perches are included for OEM springs, 60mm, and 2.5" coil over springs. The upper perch assembly incorporate a self-sliding radial bushing that allows the spring to spin during its travel instead of bind. This reduces tension on the spring and helps reduce noise and spring 'popping' noises. Bearing inserts, spacers for correct articulating angles, and 3 sizes of upper nut adapters included. The urethane bushings and bearings are replaceable if they wear out. These are designed mainly for adding negative camber for improved handling and not for camber correction back to stock settings (see Stage 1 kit). Basic instructions included but professional installation is required.

Note: suspensions vary from manufacturer to manufacturer. The proper stacked height and clearances are required. K-Mac includes bearing adapters, spacers, and various top nuts but it is still the responsibility of the installer to ensure a correct and safe fitment. As with any race-derived component, additonal fabrication may be required.

This item fits the following BMWs:
2008-2012 E82 BMW 128i 135i
6/1992-1999 E36 BMW 318i 318is 318ti 318ic 323is 323ic 325i 325is 325ic 328i 328is 328ic M3
1999-2005 E46 BMW 323i 323ci 325i 325ci 325xi 328i 328ci 330i 330ci 330xi
2006-2011 E90 BMW 325i 328i 330i 335d 335i - Sedan
2006-2012 E91 BMW 328i - Wagon
2007-2013 E92 BMW 328i 335i 335is - Coupe
2007-2013 E93 BMW 328i 335i - Convertible
1997-2003 E39 BMW 525i 528i 530i 540i (not for cars with EDC)
2004-2010 E60 BMW 525i 530i 528i 535i 545i 550i
2004-2011 E63 E64 BMW 645ci 650i
1997-2002 Z3 BMW Z3 1.9 Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i M Roadster M Coupe
2003-2008 E85 BMW Z4 2.5i Z4 3.0i Z4 3.0si
2009+ Z4 BMW Z4 sDrive28i Z4 sDrive30i Z4 sDrive35i Z4 sDrive35is
2000-2003 E52 BMW Z8 Roadster (without EDC)

Show More Show Less

KMAC Stage 1 Street Front Adjustable Camber/Caster Plates - E32, E34 ...

T#:389663

Part#: 193416-1J

Special Order: No Guaranteed ETA

$ 380.00 USD

Add to Wish List

Qty

$ 380.00 USD

Add to Wish List

Location: Front
Type: Street, Stage 1
Bearing: captive-ball fully encased in polyurethane

These front adjustable camber/caster plates will replace your stock front upper strut bearing. The KMAC plates are a 'floating' design so camber and caster are adjusted together. This design allows maximum range of adjustment since no other hardware interferes with the adjustments. Since these replace your stock strut bearings they are designed to work with a stock-type spring only. And when installed correctly will not significantly alter ride height. Adjustment is easily done by loosening the three nuts on top of the tower and sliding the camber plate into the position you want, then re-tighten the nuts. These mounts can be installed two ways - for camber correction or swapped side-side for increasing negative camber. Detailed instructions included. This KMAC part number replaces BMW part number 31 33 1 139 437, the strut mount with the integrated upper spring plate.

Note: suspensions vary from manufacturer to manufacturer. Turner Motorsport cannot be responsible for fitment issues caused by non-stock or specialized coil-over suspensions. As with any race-derived component, additonal fabrication may be required.

This item fits the following BMWs:
1988-8/92 E34 BMW 525i
1989-1995 E34 BMW 530i 535i 540i M5
1988-1994 E32 BMW 735i 735il 740i 740il 750il

Show More Show Less

Adjustable Front Camber Bushings

T#:31522921

Part#: 193616-6H

Special Order: No Guaranteed ETA

$ 320.00 USD

Add to Wish List

Qty

$ 320.00 USD

Add to Wish List

K-MAC Stage 2 Street/Race - Front Adjustable Camber/Caster Plates 195...

T#:7371477

Part#: 195416-2L

Special Order: No Guaranteed ETA

$ 545.00 USD

Add to Wish List

Qty

$ 545.00 USD

Add to Wish List

Upgrade your Mini's front top strut mounts with the K-MAC ultimate design. These mounts offer separate Camber and Caster adjustment, ensuring precise alignment even under load. Made from high-grade aircraft aluminum, they are durable and lightweight. With K-MAC's patented system, adjustments are quick and easy, allowing you to switch between Street and Race settings in just 30 seconds. The design also features heavy-duty centers encased in elastomer for extended life and minimal stack height.

Separate Camber and Caster adjustment
Quick and easy adjustments
Made from aircraft grade 7075 aluminum
Durable and lightweight construction
Compatible with OEM diam springs or smaller coil overs

Show More Show Less

Adjustable Rear Upper/Inner Camber Bushings - BMW F22/23 F3X ...

T#:16474811

Part#: 193926-9G

Special Order: No Guaranteed ETA

$ 320.00 USD

Add to Wish List

Qty

$ 320.00 USD

Add to Wish List

Nearly every car manufactured in the modern era carries a dark secret – fully-adjustable suspension has been all but eliminated in the name of cost-cutting and assembly-line efficiency. What this means for you is increased tire wear and more frequent replacement, as a “full alignment” consists only of rudimentary toe-angle adjustment. For over forty years, K-MAC has been hard at work developing a solution to this problem with patented innovations in camber/caster plates and bushing kits, allowing easy adjustment and a true “full four-wheel alignment” to be performed by any competent shop. These bushings make camber adjustments possible for the first time, and improve the ability to complete toe angle adjustments. When used in conjunction with the K-MAC Camber and Toe kit and Rear Adjustable Trailing Arms allows full adjustability of the 5 multi-link rear arms and positive location. Bolt-on installation – insertion/extraction tube included! Easily adjusted on the car with basic hand tools Unique failsafe locking hardware – set & forget! High quality elastomer compound resists binding Hardened & nickel-chrome plated centers for maximum bushing life 2x the load area of stock bushings Spiral grease grooves

Show More Show Less

KMAC Stage 3 Track Front Adjustable Camber/Caster Plates - E39 540/M5...

T#:389662

Part#: 193616-3L

Special Order: No Guaranteed ETA

$ 545.00 USD

Add to Wish List

Qty

$ 545.00 USD

Add to Wish List

Location: Front
Type: Track, Stage 3
Bearing: PTFE-lined pillow-ball, no bushing

KMAC Stage 3 camber/caster plates are designed for track or race-only situations where comfort and noise are not the primary concerns. The Stage 3 camber plates use a pillowball bearing, solidly mounted within the camber plate for direct alignment of the strut shaft and no excess play or deflection. Stage 3 are designed to increase negative camber with their patented 'floating' adjustment that changes camber and caster together. This design allows maximum range of adjustment since no other hardware interferes with the adjustments. Fitment is limited to race-only small diameter coil-over springs (not stock-type). Bearing inserts and adapters included. Detailed instructions included.

Note: suspensions vary from manufacturer to manufacturer. Turner Motorsport cannot be responsible for fitment issues caused by non-stock or specialized coil-over suspensions. As with any race-derived component, additonal fabrication may be required.

This item fits the following BMWs:
1997-2003 E39 BMW 525i 528i 530i 540i (for cars with EDC)
1999-2003 E39 BMW M5
1995-2001 E38 BMW 740i 740il 750il (for cars with EDC)
2004-2010 E60 BMW M5
2004-2011 E63 BMW M6

Show More Show Less

KMAC Street Rear Adjustable Camber/Toe Bushings - E23, E24 83-89, E28...

T#:3546

Part#: 193326

Special Order: No Guaranteed ETA

$ 269.95 USD

Add to Wish List

Qty

$ 269.95 USD

Add to Wish List

Perfect for lowered cars that need to dial out negative camber to preserve tires. Also perfect for track cars - easily dial in toe and camber for the track for better handling. Priced per set.

Fits the following BMW:
E23 BMW 7 series
83-89 E24 BMW 6 series
82-88 E28 BMW 5 series
E32 BMW 7 series
E34 BMW 5series

Show More Show Less

Adjustable Front Camber Bushings - F2X & F3X

T#:404062

Part#: 193616-8H

Special Order: No Guaranteed ETA

$ 320.00 USD

Add to Wish List

Qty

$ 320.00 USD

Add to Wish List

Upgrade your BMW's suspension system with K-MAC's innovative Camber/Caster Plates and Bushing Kits.

Combat increased tire wear and frequent replacements caused by limited adjustability with these patented solutions. For over forty years, K-MAC has been pioneering fully-adjustable suspension components, allowing for precise camber adjustments and toe angle corrections, resulting in a true "full four-wheel alignment."

Patented camber/caster plates and bushing kits for precise alignment
Allows easy adjustment for a full four-wheel alignment
Bolt-on installation with insertion/extraction tube included
Easily adjusted on the car with basic hand tools
Unique failsafe locking hardware ensures settings remain secure
High-quality elastomer compound resists binding for longevity
Hardened & nickel-chrome plated centers for maximum bushing life
Spiral grease grooves for improved lubrication

Show More Show Less

KMAC Stage 2 Street/Track Front Adjustable Camber/Caster Plates - E39...

T#:389317

Part#: 193616-2L

Special Order: No Guaranteed ETA

$ 545.00 USD

Add to Wish List

Qty

$ 545.00 USD

Add to Wish List

Location: Front
Type: Street/Track, Stage 2
Bearing: PTFE-lined pillow-ball with thin polyurethane bushing

The Stage 2 KMAC plates are a mixed street/track camber/caster plate meant to be used in a variety of suspensions. Since there is less bushing than on the Stage 1, more noise and vibration will reach the driver. The adjustment design is similar to the Stage 1 with a floating mount that sets camber and caster simultaneously. This design allows maximum range of adjustment since no other hardware interferes with the adjustments. These plates can work on both coil over and stock-stype suspensions. Bearing inserts and adapters included. The Stage 2 camber plates are shorter than a factory mount so may not be suitable for cars will little suspension travel. These are designed mainly for adding negative camber for improved handling and not for camber correction back to stock settings (see Stage 1 kit). Detailed instructions included.

Note: suspensions vary from manufacturer to manufacturer. Turner Motorsport cannot be responsible for fitment issues caused by non-stock or specialized coil-over suspensions. As with any race-derived component, additonal fabrication may be required.

This item fits the following BMWs:
2006-2008 E85 BMW Z4 M Roadster M Coupe

Show More Show Less

KMAC Stage 2 Street/Tack Front Adjustable Camber/Caster Plates - F80 ...

T#:389648

Part#: 192716-2P

Special Order: No Guaranteed ETA

$ 795.00 USD

Add to Wish List

Qty

$ 795.00 USD

Add to Wish List

KMAC camber/caster plates use a patented adjustment method designed for easy and rapid alignment adjustments. The KMAC design has a 'floating' inner camber plate, rather than slotted, to allow camber and caster to be adjusted together. To adjust, simply loosen the top three nuts on the strut tower and position the KMAC mount to match your desired alignment settings. The KMAC design allows more camber and caster adjustment because separate caster hardware is eliminated. While primarily designed to increase negative camber for track use these can also be used to fix alignment issues that cause uneven tire wear or unwanted handling behavior.

Show More Show Less

KMAC Street Rear Inner Adjustable Camber/Toe Bushings - E39 M5 ...

T#:389669

Part#: 194026J

Special Order: No Guaranteed ETA

$ 380.00 USD

Add to Wish List

Qty

$ 380.00 USD

Add to Wish List

Perfect for lowered cars that need to dial out negative camber to preserve tires. Also perfect for track cars - easily dial in toe and camber for the track for better handling. Priced per set.

This item fits the following BMWs:
1998-2004 E39 BMW M5

Show More Show Less

E36, E46, Z3 Rear Shock Mount Reinforcement (Sold Each)

T#:578621

Part#: B3300044

In Stock

Sale - Save 3% $ 8.99

This product was last offered at the strikethrough price on
05-03-2026

$ 8.68 USD

Add to Wish List

Qty

Sale - Save 3%

$ 8.99

This product was last offered at the strikethrough price on
05-03-2026

$ 8.68 USD

Add to Wish List

This is a direct replacement for the factory BMW rear shock mount reinforcement, as equipped by BMW on Z3 models. This also fits all E36 and E46 models as well. Turner Motorsport makes our own that are thicker but these can also do a good job of preventing cracks and deformation of the rear shock towers. Priced per reinforcement plate. Order 2 to cover both rear shock towers. From 1974 to 2019, Bavarian Autosport was one of the premier vendors for BMW and MINI auto parts. We are happy to preserve the Bav Auto legacy by continuing to carry their high-quality products into the future. All Bav Auto parts will remain unchanged in design and sourced from the same OEM suppliers to ensure long-lasting reliability. We trust these parts, accessories, and upgrades so confidently that we back every Bavarian Autosport branded component with a 2-year warranty. This item fits the following BMWs: 1992-1999 E36 BMW 318i 318is 318ti 318ic 323is 325i 325is 328i 328is M3 (not for convertible models) 1999-2006 E46 BMW 323i 323ci 325i 325ci 325xi 328i 328ci 330i 330ci 330xi M3 (not for convertible models) 1997-2002 Z3 BMW Z3 1.9 Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i M Roadster M Coupe

Show More Show Less

Upper Control Arm with Bushing - Right

T#:579752

Part#: 51569

In Stock

Sale - Save 80% $ 59.99

This product was last offered at the strikethrough price on
05-03-2026

$ 12.24 USD

Add to Wish List

Qty

Sale - Save 80%

$ 59.99

This product was last offered at the strikethrough price on
05-03-2026

$ 12.24 USD

Add to Wish List

Control arm with factory bushing for easy installation! If your control arm bushing is bad, it's worth buying this entire unit to save yourself time and money down the road.

K-MAC Stage 1 Street - Front Adjustable Camber/Caster Plates ...

T#:388808

Part#: 195016-1J

In Stock

37% off MSRP $ 380.00

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 238.99 USD

Limited Qty Sale

Add to Wish List

Qty

37% off MSRP

$ 380.00

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 238.99 USD

Limited Qty Sale

Add to Wish List

SPL Titanium Series Adjustable Rear Toe Arms With Eccentric Lockout K...

T#:56001958

Part#: SPLRUAE9XKT2

Ships in 1 Business Day

$ 1,258.00 USD

Add to Wish List

Qty

$ 1,258.00 USD

Add to Wish List

This premium SPL chassis upgrade kit is engineered to anchor your rear axle. Featuring SPL’s Titanium Series Rear Toe Arms with an eccentric lockout kit, alongside a complete 4 piece set of Rear Upper Wishbones and Guide Links

Show More Show Less

E36 '3' 320 323, 325 excl. 'M'Front Camber And Caster Adjustable Repl...

T#:389652

Part#: 192316-2L

Special Order: No Guaranteed ETA

$ 545.00 USD

Add to Wish List

Qty

$ 545.00 USD

Add to Wish List

K-MAC Stage 1 Street - Front Adjustable Camber/Caster Plates ...

T#:388809

Part#: 195216-1J

Special Order: No Guaranteed ETA

$ 380.00 USD

Add to Wish List

Qty

$ 380.00 USD

Add to Wish List

Location: Front
Type: Street, Stage 1
Bearing: captive-ball fully encased in polyurethane

These front adjustable camber/caster plates will replace your stock front upper strut bearing. The KMAC plates are a 'floating' design so camber and caster are adjusted together. This design allows maximum range of adjustment since no other hardware interferes with the adjustments. Since these replace your stock strut bearings they are designed to work with a stock-type spring only. And when installed correctly will not significantly alter ride height. Adjustment is easily done by loosening the three nuts on top of the tower and sliding the camber plate into the position you want, then re-tighten the nuts. These mounts can be installed two ways - for camber correction or swapped side-side for increasing negative camber. Detailed instructions included.

Note: suspensions vary from manufacturer to manufacturer. Turner Motorsport cannot be responsible for fitment issues caused by non-stock or specialized coil-over suspensions. As with any race-derived component, additonal fabrication may be required.

Show More Show Less

K-MAC Stage 2 Street/Race - Front Adjustable Camber/Caster Plates - M...

T#:387691

Part#: 195216-2L

Special Order: No Guaranteed ETA

$ 545.00 USD

Add to Wish List

Qty

$ 545.00 USD

Add to Wish List

Location: Front
Type: Street/Track, Stage 2

KMAC camber/caster plates use a patented adjustment method designed for easy and rapid alignment adjustments. The KMAC design has a 'floating' inner camber plate, rather than slotted, to allow camber and caster to be adjusted together. To adjust, simply loosen the top three nuts on the strut tower and position the KMAC mount to match your desired alignment settings. The KMAC design allows more camber and caster adjustment because separate caster hardware is eliminated. While primarily designed to increase negative camber for track use these can also be used to fix alignment issues that cause uneven tire wear or unwanted handling behavior.

Note: suspensions vary from manufacturer to manufacturer. Turner Motorsport cannot be responsible for fitment issues caused by non-stock or specialized coil-over suspensions. As with any race-derived component, additonal fabrication may be required.

Fits the following Mini Chassis:
R55, R56, R57, R56, R59, R60, R61

Show More Show Less

KMAC Stage 3 Track Front Adjustable Camber/Caster Plates - E24, E28, ...

T#:389656

Part#: 193316-3L

Special Order: No Guaranteed ETA

$ 545.00 USD

Add to Wish List

Qty

$ 545.00 USD

Add to Wish List

Location: Front
Type: Track, Stage 3
Bearing: PTFE-lined pillow-ball, no bushing

KMAC Stage 3 camber/caster plates are designed for track or race-only situations where comfort and noise are not the primary concerns. The Stage 3 camber plates use a pillowball bearing, solidly mounted within the camber plate for direct alignment of the strut shaft and no excess play or deflection. Stage 3 are designed to increase negative camber with their patented 'floating' adjustment that changes camber and caster together. This design allows maximum range of adjustment since no other hardware interferes with the adjustments. Fitment is limited to race-only small diameter coil-over springs (not stock-type). Bearing inserts and adapters included. Detailed instructions included.

Note: suspensions vary from manufacturer to manufacturer. Turner Motorsport cannot be responsible for fitment issues caused by non-stock or specialized coil-over suspensions. As with any race-derived component, additonal fabrication may be required.

This item fits the following BMWs:
1984-1991 E30 BMW 318i 318is 318ic 325e 325es 325i 325ic 325is M3
1982-1988 E28 BMW 528e 533i 535i 535is M5
1993-1995 E34 BMW 525i
1982-1989 E24 BMW 633csi 635csi M6

Show More Show Less

MINI 2nd and 3rd Gen Rear Competition HD Camber Adjustable Lower Arms...

T#:31423675

Part#: 195026K

Special Order: No Guaranteed ETA

$ 480.00 USD

Add to Wish List

Qty

$ 480.00 USD

Add to Wish List

MINI 2nd and 3rd Gen Rear Competition HD Camber Adjustable Lower Arms - Pair are designed to enhance the handling and performance of your MINI. These high-duty camber adjustable lower arms are crafted for competition use, featuring durable chrome-moly tubing and high-quality bushings. They provide precise camber adjustment to optimize wheel alignment and handling characteristics, making them ideal for track or spirited driving.

Key benefits of the MINI 2nd and 3rd Gen Rear Competition HD Camber Adjustable Lower Arms - Pair include:

Enhanced Handling: Allows for precise camber adjustments to fine-tune wheel alignment for improved handling and stability.
High-Duty Construction: Made from chrome-moly tubing for superior strength and durability under high-stress conditions.
Improved Performance: Designed for competition use, these arms are built to withstand rigorous driving demands.
Durable Bushings: Equipped with high-quality bushings to ensure reliable performance and longevity.
Optimized Alignment: Facilitates better alignment adjustments, contributing to enhanced driving dynamics and tire wear.

Show More Show Less

K-MAC Stage 3 Full Race - Front Adjustable Camber/Caster Plates ...

T#:387690

Part#: 195116-3L

Special Order: No Guaranteed ETA

$ 545.00 USD

Add to Wish List

Qty

$ 545.00 USD

Add to Wish List

KMAC Stage 1 Street Camber/Caster Plates

T#:591419

Part#: 191716-1J

Special Order: No Guaranteed ETA

$ 380.00 USD

Add to Wish List

Qty

$ 380.00 USD

Add to Wish List

These front adjustable camber/caster plates will replace your stock front upper strut bearing. The KMAC plates are a 'floating' design so camber and caster are adjusted together. This design allows maximum range of adjustment since no other hardware interferes with the adjustments. Since these replace your stock strut bearings they are designed to work with a stock-type spring only.

Show More Show Less

K-MAC Stage 2 Street / Race - Front Adjustable Camber/Caster Plates ...

T#:387715

Part#: 195116-2L

Special Order: No Guaranteed ETA

$ 545.00 USD

Add to Wish List

Qty

$ 545.00 USD

Add to Wish List

KMAC Front Adjustable Inner Thrust Arm Bushing

T#:27205341

Part#: 193316-1H

Special Order: No Guaranteed ETA

$ 320.00 USD

Add to Wish List

Qty

$ 320.00 USD

Add to Wish List

Experience effortless caster adjustment with KMAC's premium inner thrust arm bushings.

Key Features:

1. Patented Design: Enjoy precise adjustments with a single wrench, even under load directly on the alignment rack.

2. Simplified Adjustment: Say goodbye to inaccurate multi-bolt systems and time-consuming disassembly for readjustments.

3. Extensive Adjustment Range: Benefit from the largest and strongest adjustment range available.

4. Mono Ball/Dual-Axis Bushings

5. Enhance brake and steering response with these high-performance bushings.

6. Superior Design: Our unique design surpasses traditional steel spherical bearings, offering over 2 ½ times the load-bearing and impact area.

Upgrade your vehicle's handling and responsiveness with KMAC's innovative inner thrust arm bushings.

Show More Show Less

K-MAC Stage 3 Full Race - Front Adjustable Camber/Caster Plates ...

T#:388813

Part#: 195216-3L

Special Order: No Guaranteed ETA

$ 545.00 USD

Add to Wish List

Qty

$ 545.00 USD

Add to Wish List

Rear Toe Arm Bushing - Inner + Outer - Group N Race Rubber - E82, E9X...

T#:12075

Part#: E9X-GPN-TOE

Ships on Sep 17, 2026

$ 279.99 USD

Add to Wish List

Qty

$ 279.99 USD

Add to Wish List

These BMW Motorsport Group N Bushings replace all of the bushings on the factory toe control arm (also known as the track strut). These inner and outer bushings feature a heavy duty rubber that is stiffer than stock. The stiffer bushing reduces deflection and twist in the arm, leading to more stable handling and faster response in the suspension. These bushings are great for track use and legal for some racing classes yet can also be used on a street driven car where extra ride harshness can be tolerated.

Sold as a set of 4 - two bushings for each toe arm.

This item fits the following BMWs:
2008-2012 E82 BMW 128i 135i
2006-2011 E90 BMW 325i 325xi 328i 328xi 328i xDrive 330i 330xi 335d 335i 335xi 335i xDrive - Sedan
2006-2012 E91 BMW 325xi 328i 328xi 328i xDrive - Wagon
2007-2013 E92 BMW 328i 328xi 328i xDrive 335i 335is 335xi 335i xDrive - Coupe
2007-2013 E93 BMW 328i 335i - Convertible

Show More Show Less

Rear Guide Rod, Upper Link Bushing - Outer - Group N Race Rubber - E8...

T#:3093

Part#: E9X-GPN-FOLB

Ships on Sep 17, 2026

$ 519.80 USD

Add to Wish List

Qty

$ 519.80 USD

Add to Wish List

These are BMW Motorsport Group N Rear Outer bushings for the Guide Rod and Upper Link (Wishbone). This is a heavy-duty rubber that is stiffer than stock to resist deflection and twist in the arm. You'll have more stable handling and faster response in the suspension. These bushings are great for track use and legal for some racing classes yet can also be used on a street driven car where extra ride harshness can be tolerated.

Sold as a set of 4 -
2 Upper Link Outer Bushings,
2 Guide Rod Outer Bushings

This item fits the following BMWs:
2008-2012 E82 BMW 128i 135i
2006-2011 E90 BMW 325i 325xi 328i 328xi 328i xDrive 330i 330xi 335d 335i 335xi 335i xDrive - Sedan
2006-2012 E91 BMW 325xi 328i 328xi 328i xDrive - Wagon
2007-2013 E92 BMW 328i 328xi 328i xDrive 335i 335is 335xi 335i xDrive - Coupe
2007-2013 E93 BMW 328i 335i - Convertible

Show More Show Less

Rear Camber Arm - E36, E46, Z4 - Group N (Reinforced)

T#:338369

Part#: 33327749778

Ships on Sep 17, 2026

Starting at $ 198.94 USD

Add to Wish List

Starting at $ 198.94 USD

Add to Wish List

Designed and built in-house at BMW Motorsport, these are stock rear camber arms from the E36 M3 that have been strengthened by welding a reinforment in between the wishbones. Stiffer than the stock units and still adjustable for camber. This arm is legal in many racing classes where an aftermarket arm is not permitted. Sold individually, two required per car.

For maximum adjustment solid aluminum camber arms, you may also want to check out our TMS E36/E46 Adjustable Rear Camber Arms .

This arm does not include a bushing, but you may choose add a bushing using the drop down below. For an additional charge, you can get the bushing pre-pressed into the arm, so it is ready to install on the car (no added shop time or hydraulic press required).

Sold Individually.

Show More Show Less