BMW Suspension Parts

Rear Shock Mounts (RSM) - Upper - OEM Rubber - E82, E9X (non-M) (Pair...

T#:11986

Part#: E9X-URSM

In Stock

Sale - Save 2% $ 49.12

This product was last offered at the strikethrough price on
05-03-2026

$ 48.01 USD

Add to Wish List

Qty

Sale - Save 2%

$ 49.12

This product was last offered at the strikethrough price on
05-03-2026

$ 48.01 USD

Add to Wish List

A 4-piece set of new OEM rear upper and lower shock mounts to complete your shock install or replace broken mounts (RSM). The top mounts on the shocks for the E82 and E90/E91/E92/E93 consist of 4 pieces. These E9X URSM pieces fit all E82 and E9X except the M3 with EDC.

Rear Shock Mount (RSM) Kit consists of:
A. rear upper-top shock mounts, 33506771737
B. rear upper-middle shock mounts, 33506767010
C. rear upper-bottom shock mounts, 33506771738
D. rear upper supporting cup, 33526764418 (sits over bumpstop)
There is also a lower mount that is available separately. This package covers only the rear upper shock mounts.

That's a lot of rubber that takes constant deflecting and absorbing of cornering forces and impacts from bumps, potholes, etc. Replacing the RSMs is key to maintaining a quiet and comfortable ride. Price is for all 4 upper pieces for BOTH sides of the car.

This item fits the following BMWs:
2006-2011 E90 BMW 325i 325xi 328i 328xi 328i xDrive 330i 330xi 335d 335i 335xi 335i xDrive - Sedan
2006-2011 E91 BMW 325xi 328i 328xi 328i xDrive - Wagon
2007-2012 E92 BMW 328i 328xi 328i xDrive 335i 335is 335xi 335i xDrive - Coupe
2007-2012 E93 BMW 328i 335i - Convertible

Show More Show Less

KMAC Stage 1 Street Front Adjustable Camber/Caster Plates - E36, E39 ...

T#:389645

Part#: 192416-1J

In Stock

$ 380.00 USD

Add to Wish List

Qty

$ 380.00 USD

Add to Wish List

Location: Front
Type: Street, Stage 1
Bearing: captive-ball fully encased in polyurethane

These front adjustable camber/caster plates will replace your stock front upper strut bearing. The KMAC plates are a 'floating' design so camber and caster are adjusted together. This design allows maximum range of adjustment since no other hardware interferes with the adjustments. Since these replace your stock strut bearings they are designed to work with a stock-type spring only. And when installed correctly will not significantly alter ride height. Adjustment is easily done by loosening the three nuts on top of the tower and sliding the camber plate into the position you want, then re-tighten the nuts. These mounts can be installed two ways - for camber correction or swapped side-side for increasing negative camber. Detailed instructions included.

Note: suspensions vary from manufacturer to manufacturer. Turner Motorsport cannot be responsible for fitment issues caused by non-stock or specialized coil-over suspensions. As with any race-derived component, additonal fabrication may be required.

This item fits the following BMWs:
2008-2012 E82 BMW 128i 135i
6/1992-1999 E36 BMW 318i 318is 318ti 318ic 323is 323ic 325i 325is 325ic 328i 328is 328ic M3
1999-2005 E46 BMW 323i 323ci 325i 325ci 325xi 328i 328ci 330i 330ci 330xi
2006-2011 E90 BMW 325i 328i 330i 335d 335i - Sedan
2006-2012 E91 BMW 328i - Wagon
2007-2013 E92 BMW 328i 335i 335is - Coupe
2007-2013 E93 BMW 328i 335i - Convertible
1997-2003 E39 BMW 525i 528i 530i 540i (not for cars with EDC)
2004-2010 E60 BMW 525i 530i 528i 535i 545i 550i
2004-2011 E63 E64 BMW 645ci 650i
1997-2002 Z3 BMW Z3 1.9 Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i M Roadster M Coupe
2003-2008 E85 BMW Z4 2.5i Z4 3.0i Z4 3.0si
2009+ Z4 BMW Z4 sDrive28i Z4 sDrive30i Z4 sDrive35i Z4 sDrive35is
2000-2003 E52 BMW Z8 Roadster (without EDC)

Show More Show Less

Revshift Billet Aluminum Rear Trailing Arms - BMW E9X E8X (including ...

T#:1105927

Part#: BTA-E9X

Ships in 3 Business Days

$ 249.99 USD

Add to Wish List

Qty

$ 249.99 USD

Add to Wish List

These billet aluminum rear trailing arms fit the BMW E9x and E8x including the M models. They are CNC machined from 6061-T6 aluminum and are protected by a black anodized hardcoat. These trailing arms replace the flimsy stamped oem part, stiffen the rear suspension, and improve the vehicle's handling. Revshift Performance Engineering is a high-performance parts manufacturer with a focus on quality, reliability, and performance. Utilizing high-precision machining technologies and their very own Polyurethane Manufacturing Department, every Revshift product is designed, manufactured, and tested in-house at their Detroit, Michigan facility.

Show More Show Less

Bav Auto Trailing Arm Bushing and Ball Joint Tool - Master Set ...

T#:580410

Part#: B8800100

In Stock

Sale - Save 3% $ 222.99

This product was last offered at the strikethrough price on
05-03-2026

$ 216.30 USD

Add to Wish List

Qty

Sale - Save 3%

$ 222.99

This product was last offered at the strikethrough price on
05-03-2026

$ 216.30 USD

Add to Wish List

Remove and install the three bushings and ball joints that are pressed into the rear trailing arm. Use this one tool kit for on-vehicle or off-vehicle removal and replacement of the Rear Trailing Arm Bushing, Outer Upper Control Arm Bushing (ball joint) and Outer Lower Control Arm Bushing (ball joint). This tool is designed to work on E36 3-series (except E36 318ti), E46 3-series, E83 X3 and E85/E86 Z4 Coupe & Roadster.

From 1974 to 2019, Bavarian Autosport was one of the premier vendors for BMW and MINI auto parts. We are happy to preserve the Bav Auto legacy by continuing to carry their high-quality products into the future. All Bav Auto parts will remain unchanged in design and sourced from the same OEM suppliers to ensure long-lasting reliability. We trust these parts, accessories, and upgrades so confidently that we back every Bavarian Autosport branded component with a 2-year warranty.

Show More Show Less

Revshift Subframe Bushing & Reinforcement Combo Kit - Street ...

T#:27405530

Part#: SBRC-E46-80A

Ships in 7 Business Days

$ 249.99 USD

Add to Wish List

Qty

$ 249.99 USD

Add to Wish List

Upgrade your E46's rear subframe with the Revshift Combo Kit, featuring 80A durometer polyurethane rear subframe bushings and a comprehensive weld-in reinforcement plate kit. Designed to address the notorious cracking and ripping of rear subframe mounting points over time, this kit provides a robust solution to prevent costly damage to your vehicle.

Key Features:

Complete Solution: Includes 80A durometer polyurethane rear subframe bushings and precision laser-cut 14-gauge steel reinforcement plates for comprehensive subframe reinforcement. Prevents Damage: Weld-in reinforcement plates protect against cracks and damage to the chassis, ensuring long-term durability and stability. Enhanced Handling: Revshift polyurethane rear subframe bushings replace OEM rubber bushings, stiffening mounting points to improve handling and performance. Durable Construction: Polyurethane bushings are designed to last and do not wear out like rubber OEM bushings, providing consistent performance over time. Proper Dampening: Polyurethane bushings properly dampen the rear subframe, enhancing overall vehicle stability and control. Benefits:

Improved handling capabilities Long-lasting durability compared to OEM rubber bushings Protection against bending or cracking of subframe mounts The comprehensive kit includes all necessary components for installation Upgrade your E46's rear subframe with the Revshift Combo Kit for superior handling, durability, and protection against chassis damage. Boost your driving experience with enhanced performance and stability.

Show More Show Less

Revshift Subframe Bushing & Reinforcement Combo Kit - Track

T#:27405529

Part#: SBRC-E46-95A

Ships in 6 Business Days

$ 249.99 USD

Add to Wish List

Qty

$ 249.99 USD

Add to Wish List

Upgrade your E46's rear subframe with the Revshift Combo Kit, featuring 80A durometer polyurethane rear subframe bushings and a comprehensive weld-in reinforcement plate kit. Designed to address the notorious cracking and ripping of rear subframe mounting points over time, this kit provides a robust solution to prevent costly damage to your vehicle.

Key Features:

Complete Solution: Includes 95A durometer polyurethane rear subframe bushings and precision laser-cut 14-gauge steel reinforcement plates for comprehensive subframe reinforcement. Prevents Damage: Weld-in reinforcement plates protect against cracks and damage to the chassis, ensuring long-term durability and stability. Enhanced Handling: Revshift polyurethane rear subframe bushings replace OEM rubber bushings, stiffening mounting points to improve handling and performance. Durable Construction: Polyurethane bushings are designed to last and do not wear out like rubber OEM bushings, providing consistent performance over time. Proper Dampening: Polyurethane bushings properly dampen the rear subframe, enhancing overall vehicle stability and control. Benefits:

Improved handling capabilities Long-lasting durability compared to OEM rubber bushings Protection against bending or cracking of subframe mounts The comprehensive kit includes all necessary components for installation Upgrade your E46's rear subframe with the Revshift Combo Kit for superior handling, durability, and protection against chassis damage. Boost your driving experience with enhanced performance and stability.

Show More Show Less

Polyurethane Rear Trailing Arm Bushings - E36/E46

T#:582005

Part#: PTABE6GREEN

Ships in 1 Business Day

$ 79.99 USD

Add to Wish List

Qty

$ 79.99 USD

Add to Wish List

Utilizing high-precision machining technologies and their very own Polyurethane Manufacturing Department, every Revshift product is designed, manufactured, and tested in-house at their Detroit, Michigan facility.

Show More Show Less

Revshift Rear Shock Mount Kit - 80A - BMW E30 E36 E46 Z3

For shocks with a standard 10mm pin diameter

T#:1105924

Part#: RSM-E6-10MM

In Stock

$ 99.99 USD

Add to Wish List

Qty

$ 99.99 USD

Add to Wish List

Revshift rear shock mounts are CNC machined from 6061 billet aluminum and hard anodized black for protection. They are fitted with our highest quality 80A polyurethane bushings and chromoly sleeves. The class 10.9 hardware is zinc plated for corrosion resistance. These rear shock mounts can be rebuilt with one of our refresh kits sold separately. Fitment: BMW E30, E36, E46, Z3, and Z4. All OEM and aftermarket rear shocks with 10mm threads.

Show More Show Less

Polyurethane Rear Subframe Bushings - E36

T#:582007

Part#: PSBE36GREEN

Ships in 3 Business Days

$ 159.99 USD

Add to Wish List

Qty

$ 159.99 USD

Add to Wish List

Utilizing high-precision machining technologies and their very own Polyurethane Manufacturing Department, every Revshift product is designed, manufactured, and tested in-house at their Detroit, Michigan facility.

Show More Show Less

Polyurethane Rear Trailing Arm Bushings - Revshift-95A (Street/Track ...

T#:582006

Part#: PTABE30GREEN

In Stock

$ 79.99

This product was last offered at the strikethrough price on
08-12-2026

$ 72.99 USD

Limited Qty Sale

Add to Wish List

Qty

$ 79.99

This product was last offered at the strikethrough price on
08-12-2026

$ 72.99 USD

Limited Qty Sale

Add to Wish List

Utilizing high-precision machining technologies and their very own Polyurethane Manufacturing Department, every Revshift product is designed, manufactured, and tested in-house at their Detroit, Michigan facility.

Show More Show Less

Burger Motorsports Billet Strut Cross Braces - Blue - G20 M340i 330i,...

T#:637422

Part#: BMSG20BSCB-BLUE

Ships on Sep 1, 2026

$ 199.00 USD

Add to Wish List

Qty

$ 199.00 USD

Add to Wish List

Constructed from lightweight billet aluminum with the BMS logo engraved on the top middle. These strut braces are a solid one-piece design. These give an exclusive look under the hood and extra stabilization to the chassis.

Show More Show Less

Control Arm Bushings - Revshift-80A (OEM - Black)

T#:582015

Part#: PCABE30BLACK

Ships in 2 Business Days

$ 49.99 USD

Add to Wish List

Qty

$ 49.99 USD

Add to Wish List

Utilizing high-precision machining technologies and their very own Polyurethane Manufacturing Department, every Revshift product is designed, manufactured, and tested in-house at their Detroit, Michigan facility.

Show More Show Less

Burger Motorsports Billet Strut Cross Braces - Red - G20 M340i 330i, ...

T#:637421

Part#: BMSG20BSCB-RED

Ships on Sep 1, 2026

$ 199.00 USD

Add to Wish List

Qty

$ 199.00 USD

Add to Wish List

Constructed from lightweight billet aluminum with the BMS logo engraved on the top middle. These strut braces are a solid one-piece design. These give an exclusive look under the hood and extra stabilization to the chassis.

Show More Show Less

Polyurethane Rear Subframe Bushings - E36

T#:582008

Part#: PSBE36BLACK

Ships in 2 Business Days

$ 159.99 USD

Add to Wish List

Qty

$ 159.99 USD

Add to Wish List

Utilizing high-precision machining technologies and their very own Polyurethane Manufacturing Department, every Revshift product is designed, manufactured, and tested in-house at their Detroit, Michigan facility.

Show More Show Less

BMS Billet Strut Cross Braces - Anodized Blue - BMW G01 X3, G02 X4, F...

T#:39126850

Part#: BMSBILSCB-BLU

In Stock

$ 249.00 USD

Add to Wish List

Qty

$ 249.00 USD

Add to Wish List

Burger Motorsports' Billet Strut Cross Braces are designed and made in the USA from billet aluminum in a solid one-piece design. These braces connect from the strut towers to the front radiator support, helping to reinforce your entire front end while also giving your BMW an exclusive under-hood appearance.

Show More Show Less

KMAC Adjustable Rear Camber And Toe Bushings Set - E82, E89, E9X non-...

T#:389667

Part#: 193926K

In Stock

13% off MSRP $ 480.00

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 417.00 USD

Limited Qty Sale

Add to Wish List

Qty

13% off MSRP

$ 480.00

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 417.00 USD

Limited Qty Sale

Add to Wish List

Rear adjustable camber and toe bushings for the E82/E9X non-M 3-series. These bushings allow you to adjust camber and toe beyond factory specs to either restore camber or add more. If you lowered your car and have too much camber these bushings can get you back to stock specs. On the flip side if you need more camber for the track or autocross, you can fine tune it with these too. These bushings press in and replace the existing rubber bushings. They are made from peformance urethane which will give more feedback and response to the driver. Sold as a set with a bushing extraction tool included.

Fits the following BMWs:
E82/88 BMW 2 Series
E89 BMW Z4
E9X BMW Non-M

Show More Show Less

KMAC Stage 1 Street Front Adjustable Camber/Caster Plates - E39 540/M...

T#:389661

Part#: 193616-1J

Ships on Sep 11, 2026

$ 380.00 USD

Add to Wish List

Qty

$ 380.00 USD

Add to Wish List

Location: Front
Type: Street, Stage 1
Bearing: captive-ball fully encased in polyurethane

These front adjustable camber/caster plates will replace your stock front upper strut bearing. The KMAC plates are a 'floating' design so camber and caster are adjusted together. This design allows maximum range of adjustment since no other hardware interferes with the adjustments. Since these replace your stock strut bearings they are designed to work with a stock-type spring only. And when installed correctly will not significantly alter ride height. Adjustment is easily done by loosening the three nuts on top of the tower and sliding the camber plate into the position you want, then re-tighten the nuts. These mounts can be installed two ways - for camber correction or swapped side-side for increasing negative camber. Detailed instructions included.

Note: suspensions vary from manufacturer to manufacturer. Turner Motorsport cannot be responsible for fitment issues caused by non-stock or specialized coil-over suspensions. As with any race-derived component, additonal fabrication may be required.

This item fits the following BMWs:
1997-2003 E39 BMW 525i 528i 530i 540i (for cars with EDC)
1999-2003 E39 BMW M5
1995-2001 E38 BMW 740i 740il 750il (for cars with EDC)

Show More Show Less

Bav Auto Rear Subframe Bushing Press - E88 E9X BMW

T#:580432

Part#: B8800127

In Stock

Sale - Save 3% $ 419.99

This product was last offered at the strikethrough price on
05-03-2026

$ 407.39 USD

Add to Wish List

Qty

Sale - Save 3%

$ 419.99

This product was last offered at the strikethrough price on
05-03-2026

$ 407.39 USD

Add to Wish List

The Bav Auto Rear Subframe Bushing Press allows you to remove and install rear subframe bushings while the subframe is still in the vehicle, saving you several hours of labor.

Revshift Rear Shock Mount Kit - 80A - BMW E30 E36 E46 Z3

For shocks with a larger 12mm pin diameter

T#:1105925

Part#: RSM-E6-12MM

Ships in 2 Business Days

$ 99.99 USD

Add to Wish List

Qty

$ 99.99 USD

Add to Wish List

Revshift rear shock mounts are CNC machined from 6061 billet aluminum and hard anodized black for protection. They are fitted with our highest quality 80A polyurethane bushings and chromoly sleeves. The class 10.9 hardware is zinc plated for corrosion resistance. These rear shock mounts can be rebuilt with one of our refresh kits sold separately. Fitment: BMW E30, E36, E46, Z3, and Z4. All OEM and aftermarket rear shocks with 12mm threads.

Show More Show Less

Polyurethane Rear Subframe Bushings - E30

T#:1105916

Part#: PSB-E3095A

Ships in 7 Business Days

$ 89.99 USD

Add to Wish List

Qty

$ 89.99 USD

Add to Wish List

Utilizing high-precision machining technologies and their very own Polyurethane Manufacturing Department, every Revshift product is designed, manufactured, and tested in-house at their Detroit, Michigan facility.

Show More Show Less

Burger Motorsports Billet Strut Cross Braces - Black - G20 M340i 330i...

T#:637424

Part#: BMSG20BSCB-BLK

Ships in 7 Business Days

$ 199.00 USD

Add to Wish List

Qty

$ 199.00 USD

Add to Wish List

Constructed from lightweight billet aluminum with the BMS logo engraved on the top middle. These strut braces are a solid one-piece design. These give an exclusive look under the hood and extra stabilization to the chassis.

Show More Show Less

Rear Polyurethane Bushing Kit - E30

T#:1105909

Part#: RBK-E3095A

Ships in 5 Business Days

$ 199.99 USD

Add to Wish List

Qty

$ 199.99 USD

Add to Wish List

Utilizing high-precision machining technologies and their very own Polyurethane Manufacturing Department, every Revshift product is designed, manufactured, and tested in-house at their Detroit, Michigan facility.

Show More Show Less

Full Polyurethane Bushing Kit - E36

T#:1105899

Part#: FBK-E36C95A

Ships in 5 Business Days

$ 379.99 USD

Add to Wish List

Qty

$ 379.99 USD

Add to Wish List

Utilizing high-precision machining technologies and their very own Polyurethane Manufacturing Department, every Revshift product is designed, manufactured, and tested in-house at their Detroit, Michigan facility.

Show More Show Less

Adjustable Rear Upper/Inner Camber Bushings

T#:600206

Part#: 193926-3H

Ships on Sep 11, 2026

$ 320.00 USD

Add to Wish List

Qty

$ 320.00 USD

Add to Wish List

Nearly every car manufactured in the modern era carries a dark secret – fully-adjustable suspension has been all but eliminated in the name of cost-cutting and assembly-line efficiency. What this means for you is increased tire wear and more frequent replacement, as a “full alignment” consists only of rudimentary toe-angle adjustment. For over forty years, K-MAC has been hard at work developing a solution to this problem with patented innovations in camber/caster plates and bushing kits, allowing easy adjustment and a true “full four-wheel alignment” to be performed by any competent shop. These bushings make camber adjustments possible for the first time, and improve the ability to complete toe angle adjustments. When used in conjunction with the K-MAC Camber and Toe kit and Rear Adjustable Trailing Arms allows full adjustability of the 5 multi-link rear arms and positive location. Bolt-on installation – insertion/extraction tube included! Easily adjusted on the car with basic hand tools Unique failsafe locking hardware – set & forget! High quality elastomer compound resists binding Hardened & nickel-chrome plated centers for maximum bushing life 2x the load area of stock bushings Spiral grease grooves

Show More Show Less

K-MAC Stage 1 Street - Front Adjustable Camber/Caster Plates ...

T#:388807

Part#: 195116-1J

Ships on Sep 11, 2026

$ 380.00 USD

Add to Wish List

Qty

$ 380.00 USD

Add to Wish List

Location: Front
Type: Street, Stage 1
Bearing: captive-ball fully encased in polyurethane

These front adjustable camber/caster plates will replace your stock front upper strut bearing. The KMAC plates are a 'floating' design so camber and caster are adjusted together. This design allows maximum range of adjustment since no other hardware interferes with the adjustments. Since these replace your stock strut bearings they are designed to work with a stock-type spring only. And when installed correctly will not significantly alter ride height. Adjustment is easily done by loosening the three nuts on top of the tower and sliding the camber plate into the position you want, then re-tighten the nuts. These mounts can be installed two ways - for camber correction or swapped side-side for increasing negative camber. Detailed instructions included.

Note: suspensions vary from manufacturer to manufacturer. Turner Motorsport cannot be responsible for fitment issues caused by non-stock or specialized coil-over suspensions. As with any race-derived component, additonal fabrication may be required.

This item fits the following BMWs:
3/2002-2006 R50 MINI MINI Cooper
2005-2008 R52 MINI MINI Cooper Convertible, MINI Cooper S Convertible.
3/2002-2006 R53 MINI MINI Cooper S

Show More Show Less

BMW Motorsport Rear Sway Bar Bushing - 14-15mm - E90 E92 E82 ...

T#:3213

Part#: 33558300883

Ships on Sep 17, 2026

$ 31.99 USD

Add to Wish List

Qty

$ 31.99 USD

Add to Wish List

This is the factory BMW Motorsport Group N high performance rear sway bar / swaybar bushing for cars with a 14/15mm sway bar. This heavy duty rubber bushing is stiffer than the stock bushing to improve handling. They are great for track use - and Grand Am Cup legal! - yet can also be used on a street driven car - please note these will not be as compliant as the stock rubber bushing.

Sold Individually

This item fits the following BMWs:
2008+ E82 BMW 128i 135i
2006+ E90 BMW 325i 328i 330i 335i
2007+ E92 BMW 328i 335i 335is
2007+ E93 BMW 328i 335i

Show More Show Less

Rear Subframe Bushings/Mounts - Set - Group N Race Rubber - E82, E9X ...

T#:12076

Part#: E9X-GPN-SUBFRAME

In Stock

$ 800.00 USD

Add to Wish List

Qty

$ 800.00 USD

Add to Wish List

The E82 and E90/E92 subframes have an inherent weakness in the rear subframe - the mounts are too soft for the power and torque these cars are capable of. The subframe is the heart of a BMW's rear suspension. As torque is transmitted through the differential and axles and as the tires grip the road, the subframe mounts are working to keeping everything in line. That's a tough task to hold when torque is increased with bigger boost (335i) or even mild tweaks (M3). While the M3 subframe mounts are a great upgrade for the non-M chassis these factory BMW Motorsport subframe mounts go one step further.

These Motorsport/Group N rear subframe bushings are a direct replacement upgrade over the stock mounts. They are rubber to conform to the rules of the Group N racing class - so they are still acceptable for street use as long as extra ride harshness can be tolerated. The rear subframe has to come down from the car for these mounts to be pressed in. So now is the perfect time to do other work as well - check out our other Motorsport Race bushings or M3 upgrades.

Price is for the set of 4 mounts.

This item fits the following BMWs:
2008-2012 E82 BMW 128i 135i 1M Coupe
2006-2011 E90 BMW 325i 325xi 328i 328xi 328i xDrive 330i 330xi 335d 335i 335xi 335i xDrive M3 - Sedan
2006-2012 E91 BMW 325xi 328i 328xi 328i xDrive - Wagon
2007-2013 E92 BMW 328i 328xi 328i xDrive 335i 335is 335xi 335i xDrive M3 - Coupe
2007-2013 E93 BMW 328i 335i M3 - Convertible

Show More Show Less

KMAC Stage 1 Street Front Adjustable Camber/Caster Plates - E24, E28,...

T#:389654

Part#: 193316-1J

Special Order: No Guaranteed ETA

$ 379.99 USD

Add to Wish List

Qty

$ 379.99 USD

Add to Wish List

Location: Front
Type: Street, Stage 1
Bearing: captive-ball fully encased in polyurethane

These front adjustable camber/caster plates will replace your stock front upper strut bearing. The KMAC plates are a 'floating' design so camber and caster are adjusted together. This design allows maximum range of adjustment since no other hardware interferes with the adjustments. Since these replace your stock strut bearings they are designed to work with a stock-type spring only. And when installed correctly will not significantly alter ride height. Adjustment is easily done by loosening the three nuts on top of the tower and sliding the camber plate into the position you want, then re-tighten the nuts. These mounts can be installed two ways - for camber correction or swapped side-side for increasing negative camber. Detailed instructions included.

Note: suspensions vary from manufacturer to manufacturer. Turner Motorsport cannot be responsible for fitment issues caused by non-stock or specialized coil-over suspensions. As with any race-derived component, additonal fabrication may be required.

This item fits the following BMWs:
1984-1991 E30 BMW 318i 318is 318ic 325e 325es 325i 325ic 325is M3
1982-1988 E28 BMW 528e 533i 535i 535is M5
1993-1995 E34 BMW 525i
1982-1989 E24 BMW 633csi 635csi M6

Show More Show Less

Bav Auto Rear Subframe Bushing Press Tool

T#:580407

Part#: B8800097

In Stock

Sale - Save 3% $ 383.99

This product was last offered at the strikethrough price on
05-03-2026

$ 372.47 USD

Add to Wish List

Qty

Sale - Save 3%

$ 383.99

This product was last offered at the strikethrough price on
05-03-2026

$ 372.47 USD

Add to Wish List

Allows you to both remove and install rear subframe to body bushings without removing your subframe, saving you hours of labor from having to disassemble suspension components.

Revshift Billet Aluminum Subframe Bushing Kit - BMW E9X E82

T#:1105926

Part#: ASB-E9X

Ships in 4 Business Days

$ 299.99 USD

Add to Wish List

Qty

$ 299.99 USD

Add to Wish List

Revshift billet aluminum subframe bushings completely replace the oem rubber bushings on the BMW E82, E90, E91, E92, and E93 including the M3, 1M, and XI models. These bushings solid mount the rear subframe reducing wheel hop and improving the vehicles handling capabilities. The two piece bushing design sandwiches the subframe locking it in place. It will not shift on the bushings while driving like the one piece designs allow. They are CNC machined at Revshift in the USA from 6061-T6 billet aluminum.

Show More Show Less

Control Arm Bushings - Revshift-95A (Street/Track - Green)

T#:582014

Part#: PCABE30GREEN

Ships in 7 Business Days

$ 49.99 USD

Add to Wish List

Qty

$ 49.99 USD

Add to Wish List

Utilizing high-precision machining technologies and their very own Polyurethane Manufacturing Department, every Revshift product is designed, manufactured, and tested in-house at their Detroit, Michigan facility.

Show More Show Less

Polyurethane Rear Subframe Bushings - E34

T#:1105932

Part#: PSB-E3480A

Ships in 1 Business Day

$ 119.99 USD

Add to Wish List

Qty

$ 119.99 USD

Add to Wish List

Utilizing high-precision machining technologies and their very own Polyurethane Manufacturing Department, every Revshift product is designed, manufactured, and tested in-house at their Detroit, Michigan facility.

Show More Show Less

Full Polyurethane Bushing Kit - E36 - 95A - Green - Offset Bushings ...

T#:1980634

Part#: FBKOFFSET

Ships in 7 Business Days

$ 379.99 USD

Add to Wish List

Qty

$ 379.99 USD

Add to Wish List

Stiffen your suspension and improve your handling with these Revshift upgraded suspension bushings. Improves handing Will not wear out like oem bushings Properly dampens suspension components

Burger Motorsports Billet Strut Cross Braces - Silver - G20 M340i 330...

T#:637423

Part#: BMSG20BSCB-SIL

Ships on Sep 1, 2026

$ 255.99 USD

Add to Wish List

Qty

$ 255.99 USD

Add to Wish List

Constructed from lightweight billet aluminum with the BMS logo engraved on the top middle. These strut braces are a solid one-piece design. These give an exclusive look under the hood and extra stabilization to the chassis.

Show More Show Less

Billet Strut Cross Braces For G30 G14 G15 G16

T#:27138580

Part#: BMSG30SB

Ships on Sep 1, 2026

Starting at $ 249.00 USD

Add to Wish List

Starting at $ 249.00 USD

Add to Wish List

The Burger Motorsports Billet Strut Cross Braces for the G30, G14, G15, and G16 are designed and made in the USA from lightweight billet aluminum with the BMS logo engraved on the top middle. These strut braces are a solid one-piece design. These give an exclusive look under the hood and extra stabilization to the chassis. Easy 5-minute install. Simply remove your factory strut braces and replace them with the BMS units for better structural integrity and amazing looks under the hood. Sold in pairs. Available in Black, Silver, Blue, and Red anodized. Single-piece design made from a solid block of billet aluminum Improved chassis rigidity and structural integrity Decreased chassis flex during cornering Utilizes stock mounting bolts Direct bolt-on replacement. No drilling required Made in the USA

Show More Show Less

BMS Billet Strut Cross Braces - Anodized Black - BMW G01 X3, G02 X4, ...

T#:39126853

Part#: BMSBILSCB-BLK

Ships on Sep 1, 2026

$ 249.00 USD

Add to Wish List

Qty

$ 249.00 USD

Add to Wish List

Burger Motorsports' Billet Strut Cross Braces are designed and made in the USA from billet aluminum in a solid one-piece design. These braces connect from the strut towers to the front radiator support, helping to reinforce your entire front end while also giving your BMW an exclusive under-hood appearance.

Show More Show Less

Polyurethane Rear Subframe Bushings - E46

T#:1105904

Part#: PSB-E46M

Ships in 7 Business Days

$ 189.99 USD

Add to Wish List

Qty

$ 189.99 USD

Add to Wish List

Utilizing high-precision machining technologies and their very own Polyurethane Manufacturing Department, every Revshift product is designed, manufactured, and tested in-house at their Detroit, Michigan facility.

Show More Show Less

Polyurethane Rear Subframe Bushings - E36 318ti

T#:1105922

Part#: PSB-318TI95A

In Stock

$ 89.99

This product was last offered at the strikethrough price on
07-30-2026

$ 81.99 USD

Limited Qty Sale

Add to Wish List

Qty

$ 89.99

This product was last offered at the strikethrough price on
07-30-2026

$ 81.99 USD

Limited Qty Sale

Add to Wish List

Utilizing high-precision machining technologies and their very own Polyurethane Manufacturing Department, every Revshift product is designed, manufactured, and tested in-house at their Detroit, Michigan facility.

Show More Show Less

Burger Motorsports Billet Strut Cross Braces - Red - BMW G22/G23/G26 ...

T#:46924996

Part#: G22BSCB-RED

Ships on Sep 1, 2026

$ 199.00 USD

Add to Wish List

Qty

$ 199.00 USD

Add to Wish List

Burger Motorsports' strut braces are CNC machined from thick, lightweight billet aluminum with the BMS logo engraved on the top middle. These strut braces are a thick, solid one-piece design and give an exclusive look under the hood and extra stabilization to the chassis.

Show More Show Less

Rear Polyurethane Bushing Kit - E30 12MM Offset

T#:1105914

Part#: RBK-E3095A12MM

Ships in 7 Business Days

$ 224.99 USD

Add to Wish List

Qty

$ 224.99 USD

Add to Wish List

Utilizing high-precision machining technologies and their very own Polyurethane Manufacturing Department, every Revshift product is designed, manufactured, and tested in-house at their Detroit, Michigan facility.

Show More Show Less

Polyurethane Rear Subframe Bushings - E30 325iX

T#:1105918

Part#: PSB-E30IX95A

Ships in 7 Business Days

$ 89.99 USD

Add to Wish List

Qty

$ 89.99 USD

Add to Wish List

Utilizing high-precision machining technologies and their very own Polyurethane Manufacturing Department, every Revshift product is designed, manufactured, and tested in-house at their Detroit, Michigan facility.

Show More Show Less

Polyurethane Rear Subframe Bushings - E30 12MM Offset

T#:1105917

Part#: PSB-E3012MM95A

Ships in 7 Business Days

$ 119.99 USD

Add to Wish List

Qty

$ 119.99 USD

Add to Wish List

Utilizing high-precision machining technologies and their very own Polyurethane Manufacturing Department, every Revshift product is designed, manufactured, and tested in-house at their Detroit, Michigan facility.

Show More Show Less

Revshift Polyurethane Subframe Bushings - 95A (Track - Green) - BMW E...

T#:47199273

Part#: PSB-E9X-95A

Ships in 1 Business Day

$ 249.99 USD

Add to Wish List

Qty

$ 249.99 USD

Add to Wish List

Revshift polyurethane subframe bushings completely replace the OEM rubber bushings on the BMW E82, E81, E87, E88, E90, E91, E92, and E93, including the M3, 1M, and XI models. These bushings securely mount the rear subframe, reducing wheel hop and improving the vehicle's handling capabilities. The two-piece bushing design sandwiches the subframe, locking it in place. It will not shift on the bushings while driving, like the one-piece designs allow. They are entirely made at Revshift in the USA from our proprietary polyurethane formula and CNC-machined billet aluminum cores.

Show More Show Less

Offset Control Arm Bushings - E30 M3

T#:582012

Part#: PCABE30M3GREEN

Ships in 7 Business Days

$ 49.99 USD

Add to Wish List

Qty

$ 49.99 USD

Add to Wish List

Utilizing high-precision machining technologies and their very own Polyurethane Manufacturing Department, every Revshift product is designed, manufactured, and tested in-house at their Detroit, Michigan facility.

Show More Show Less

Offset Control Arm Bushings - Solid - E30 M3

T#:582013

Part#: PCABE30M3

Ships in 7 Business Days

$ 49.99 USD

Add to Wish List

Qty

$ 49.99 USD

Add to Wish List

Utilizing high-precision machining technologies and their very own Polyurethane Manufacturing Department, every Revshift product is designed, manufactured, and tested in-house at their Detroit, Michigan facility.

Show More Show Less

Front Upper Control Arm Bushing Set (FCAB) - Group N Race Rubber - E8...

T#:2309

Part#: E9X-GPN-UCAB

Ships in 8 Business Days

$ 413.38 USD

Add to Wish List

Qty

$ 413.38 USD

Add to Wish List

These are the factory BMW Motorsport Group N high performance front upper control arm bushings. These heavy duty rubber bushings are stiffer than the stock bushings to improve steering feel and improve handling. They are great for track use - and Grand Am Cup legal! - yet can also be used on a street driven car - please note these will not be as compliant as the stock rubber bushings. These are for the control arm with the ball joint pointing down, sometimes referred to as the thrust arm or tension strut.

Price is for the pair of bushings.

This item fits the following BMWs:
2008-2012 E82 BMW 128i 135i 1M
2006-2011 E90 BMW 325i 328i 330i 335d 335i M3 - Sedan
2006-2011 E91 BMW 328i - Wagon
2007-2012 E92 BMW 328i 335i 335is M3 - Coupe
2007-2012 E93 BMW 328i 335i M3 - Convertible

Show More Show Less

Adjustable Rear Camber/Toe Bushings

T#:582353

Part#: 192026G

In Stock

$ 320.00 USD

Add to Wish List

Qty

$ 320.00 USD

Add to Wish List

KMAC Stage 2 Street/Track Front Adjustable Camber/Caster Plates - F22...

T#:389642

Part#: 192616-2N

Special Order: No Guaranteed ETA

$ 695.00 USD

Add to Wish List

Qty

$ 695.00 USD

Add to Wish List

Location: Front
Type: Street/Track, Stage 2
Upper spring perch: OEM-size, 60mm, and 2.5" included
Bearings: urethane OEM-type center bushing; lubricated radial thrust bearing on spring perch

KMAC camber/caster plates use a patented adjustment method designed for easy and rapid alignment adjustments. The KMAC design has a 'floating' inner camber plate, rather than slotted, to allow camber and caster to be adjusted together. To adjust, simply loosen the top three nuts on the strut tower and position the KMAC mount to match your desired alignment settings. The KMAC design allows more camber and caster adjustment because separate caster hardware is eliminated. While primarily designed to increase negative camber for track use these can also be used to fix alignment issues that cause uneven tire wear or unwanted handling behavior.

KMAC camber kits are the most complete kits on the market, with all of the common spring perch options and strut hardware included. The OEM size spring perch as well as 60mm and 2.5" spring isolators are included which makes it easy to upgrade from stock struts to coil overs without having to buy new camber plates. Or swap springs on your coil overs between 60mm and 2.5" without buying additional upper perches. Also included are the most common strut pin hardware - 14mm lower bearing adapters and 12x1.5, 12x1.75, and 14x1.5 top nuts. This takes the guesswork out of ordering the correct hardware for your strut type. The urethane main bushing is also replaceable and the camber plate parts are made from 7075-grade aluminum for a lifetime of camber plate use.

Fitment Note 1: replaces factory BMW strut mount with 3 mounting bolts (up to 12/2014 prodution). Not for cars with 5-bolt strut mounts.

Fitment Note 2: suspensions vary from manufacturer to manufacturer. The proper stacked height and clearances are required. K-MAC includes bearing adapters, spacers, and various top nuts but it is still the responsibility of the installer to ensure a correct and safe fitment. Basic instructions are included but professional installation is required. As with any race-derived component, additonal fabrication may be required.

This item fits the following BMWs:
-12/2014 F22 BMW 228i 228i xDrive M235i M235i xDrive
2012-12/2014 F30 BMW 320i 320i xDrive 328d 328d xDrive 328i 328i xDrive 335i 335i xDrive - Sedan
2013-12/2014 F31 BMW 328i xDrive 328d xDrive - Wagon
-12/2014 F34 BMW 328i xDrive GT, 335i xDrive GT - Gran Tourismo
2013-12/2014 F32 BMW 428i 428i xDrive 435i 435i xDrive - Coupe
2013-12/2014 F33 BMW 428i Convertible 428i xDrive Convertible 435i Convertible - Convertible
-12/2014 F36 BMW 428i Gran Coupe 428i xDrive Gran Coupe 435i Gran Coupe 435i xDrive Gran Coupe
Not for cars with Adaptive M Suspension option code S2VFA

Show More Show Less

Project Cars

SELECT YOUR BMW

Sub-Categories

Select Vehicle

Purpose

Category

Brand

Price

Special Offers

Shipping

Narrow Results