BMW Suspension Parts

Upgrade your BMW's suspension with ECS Tuning Adjustable Sway Bar End Links, designed to provide up to 60mm (2.36") of adjustability. These end links allow you to eliminate sway bar preload or fine-tune it for specific racing needs and corner balancing. When installed, they improve drivetrain clearance and enhance sway bar responsiveness by reducing deflection, ensuring superior handling. Perfect for lowered vehicles using springs, coilovers, or air-ride suspension systems, these adjustable sway bar end links allow you to remove unwanted preload caused by changes in the center-to-center distance between sway bar mounting points. By adjusting the end links to a neutral position, you eliminate sway bar preload, enhancing suspension performance in various driving conditions.

The main body of the ECS Sway Bar End Links is crafted from strong, lightweight 6061-T6 billet aluminum and anodized red for superior corrosion resistance. Featuring left and right-hand threaded center sections and machined hex wrench fittings, these end links allow for quick and easy on-the-car adjustments. Zinc-plated hardware ensures secure and lasting adjustments, while the heavy-duty ball joint ends come with weather-resistant rubber boots and stainless steel wire retainers, providing superior protection against salt, rain, and ozone for extended durability. Each kit also includes zinc-plated Nyloc nuts and hardened steel washers for secure installation and improved contact surface on the sway bar.

These end links are designed, engineered, and rigorously tested by ECS Tuning to ensure the highest quality. Whether you have a lowered or stock suspension, these adjustable sway bar end links are the perfect upgrade, offering a high-quality, heavy-duty replacement that fits your specific needs.

Features:

Range of Adjustment: 215mm (8.46") to 275mm (10.82") 6061-T6 Billet Aluminum Construction: Red anodized for superior corrosion resistance Zinc-Plated Hardware: Provides durability and superior corrosion protection Right and Left-Hand Threaded Center Sections: Quick and simple on-the-car adjustments Heavy-Duty Ball Joints(M10x1.5): Weather-resistant rubber boots and stainless steel wire retainers for long-lasting durability

Upgrade your vehicle's performance with our replacement rear lower control arm inner bushings. These bushings feature a low-friction, PTFE-lined spherical bearing, enhancing cornering grip and dynamic geometry. By eliminating OEM bushing deflection and binding, our product preserves camber and toe geometry during bumps. Enjoy improved stability and handling precision, thanks to the maintenance-free FK bearings with PTFE linings. Crafted from high-quality materials including 6061-T6 aluminum and FK PTFE-lined spherical bearings, our bushings ensure durability and NVH reduction. Experience the benefits of enhanced performance and reliability with our premium upgrade.

Key Advantages:

Enhanced Rear Cornering Grip Elimination of OEM Bushing Deflection and Binding Improved Dynamic Geometry, Stability, and Handling Precision Maintenance-Free FK Bearings, Manufactured in the US, with PTFE Linings Materials Used:

6061-T6 Aluminum Bearing Shells and Spacers FK PTFE-Lined Spherical Bearings (F1 Specification, Self-Cleaning)

Black anodized billet sway bar end links to replace your flimsy and corroded factory units. Removable hardware for a lifetime serviceable component!

Your factory end link brackets are a one piece design with an integrated stud made of flimsy metal with no coating to protect from the elements. Over the years the end link hardware rusts right to the integrated stud and when you go to remove the end links or brackets they are one strong turn and a snap away from needing to be replaced.

Not only did ECS come up with a stronger solution with a superior resistance to corrosion but went the extra mile to incorporate hardware that can be replaced time and time again so you will never need to replace the brackets themselves. The end link brackets feature chamfers and locator pins to fit perfectly in factory location and make for a straight forward install. The brackets featuring a slotted area for the bolt head to sit so you don't have the headache of having to get a wrench in the tight space behind the bracket while installing them.

Kit Contents:

A pair of rear end link brackets
Hardware needed for installation
Part Design:

Billet aluminum brackets
Zinc coated hardware
Superior corrosion resistance
Large upgrade from factory components

Due to their soft rubber construction, OE strut mounts are known to wear at an accelerated rate. Many high-mileage vehicles fall victim to strut mount failure, which is commonly associated with annoying clunks, groans, or rattles from the front suspension.

With this issue in mind, ECS Tuning developed their heavy-duty front strut mount with upgraded, higher durometer rubber to resolve sloppy handling and increase longevity. Manufactured precisely within OEM tolerances, these mounts are a perfect fit for your MINI.

Features:

Reduces deflection: Increases vehicle handling and cornering dynamics by removing deflection within the strut mount. Increases longevity: Upgraded rubber construction makes for a stiffer mount, less prone to cracking and general degradation. Developed in-house: Designed and tested by ECS Tuning engineers, this mount is sure to outlast an OE replacement. Upgrade to a better strut mount without sacrificing ride comfort! Improve longevity and ride control all at once.

BMW E46 Z4 Rear Polyurethane Differential Bushing Performance is the ultimate upgrade for enhancing the connection between your BMW's chassis and differential. Designed by Turner Motorsport, this performance bushing replaces the soft factory rubber with durable polyurethane, offering superior control and response. By minimizing vibrations and reducing deflection, this bushing ensures a more direct and responsive driving experience, making it a must-have for any performance-oriented BMW E46 or Z4 owner.

• Enhanced Performance: Replaces the soft factory rubber with durable polyurethane for improved driveline response.
• Reduced Vibrations: Minimizes vibrations between the chassis and differential, providing a more connected driving experience.
• Increased Durability: Made from high-quality polyurethane, offering long-lasting performance under demanding conditions.
• Improved Control: Reduces deflection, ensuring a more precise and responsive handling experience.

Dramatically improve performance and aesthetics with an average lowering up to 1.4" front and rear.

Take your F3x to the next level with upgraded performance and aesthetic. ECS lowering springs are specifically designed with both handling and comfort in mind for the best mix or performance and drivability. With an average lowering range of 1.0"-1.4" you have the added benefit of lower center of gravity providing superior cornering and better steering feedback. Lowering springs not only increase handling performance they provide an astounding aesthetic upgrade by decreasing the wheel gap and giving your car a more planted/fitted appearance.

FEATURES AND DESIGN:

MADE IN THE USA
Average lowering of 1.0" to 1.4"
Front spring rate: 184 lbs/in
Rear spring rate: 462 lbs/in
Lowered center of gravity
Linear style springs
Black powder coating with red ECS logo
Designed specifically for your chassis these F3x lowering springs feature a linear style spring similar to a coilover. The issue with coilovers is the rough ride due to a drastic drop and much higher spring rates. When you have higher spring rate like coilovers it takes much more force to compress the spring which leads to a much more rigid ride. ECS lowering springs provide a happy medium between the factory suspension and coilover suspension. These springs are stiffer than factory but softer than a coilover spring to achieve the balance of increased performance and aesthetics while retaining a comfortable ride.

What is spring rate?
​You may ask yourself "what is the spring rate and how does it affect my ride?" Spring rate is the amount of force needed to compress a spring one inch. For example if you have a spring rate of 300lbs per inch it will take 300lbs of force to compress the spring one inch. An average coilover for your F3x has over 400 lbs/in for the front and over 500 lbs/in for the rear, this means that it will take over 400lbs of force to compress your front spring one inch and over 500lbs of force to compress the rear one inch. The higher the spring rate, the more rigid your ride is going to be. ECS lowering springs for your F3x have a spring rate of 184 lbs/in in the front and 462 lbs/in, an increase over factory but much less than a coilover. You can now both understand and explain the benefits of lowering springs to find the best solution for you.

Fine-tuning your coilover damping shouldn’t mean stripping out your rear seats or interior panels. On many applications, rear shock adjusters are hidden behind carpet, trim, or seatbacks, making quick adjustments a hassle.

The ECS Rear Damping Extension Kit solves that problem with a clean and functional solution. These flexible extensions relocate the adjustment knobs to an easily accessible point above the rear shock towers, letting you dial in your suspension from inside the cabin, no disassembly required.

Installation is straightforward: simply drill a small access hole in your interior trim and route the extension cables through. The adjustment knobs can be removed to allow the line to pass through smaller openings, minimizing cutting. For proper installation, be sure to fully loosen the set screw, insert the cable, then securely tighten it using the provided Allen key.

Kit Includes:

(2) Rear damping adjuster extension cables

Installation hardware and Allen key

A smart upgrade for track cars, daily drivers, or anyone who values easy access to suspension tuning, without compromising interior fit and finish.

The SPL BMW F2X/F3X Front Lower Control Arms (FLCA) provide roll center, camber, and track width adjustment for the rear wheel drive (RWD) F2X/F3X BMWs while eliminating bushing deflection resulting in sharpened steering response and driving precision.

Negative Camber Benefits

The ability to run more negative camber greatly improves the peak lateral grip available. Adding negative camber results in the tire having an optimal contact patch as the body rolls due to cornering forces. This is especially important with better tires and a must-have for anyone looking to prevent excessive outer shoulder wear (and heating) on their tires due to a lack of camber.

Wider Front Track Width Benefits

Further handling improvements can be had by increasing the front track width from the factory 60.5" (F3X) or 59.9" (F2X) to be closer to the M3's 62.2". If you applied the M3's width to the M340i it would reduce the outer front tire loading by roughly 20 lbs and apply it to the inner front tire. The result would be greater peak grip (~0.04G), improved stability, and faster lap times.

Roll Center Correction Benefits

Lowering the F2X/F3X results in a greater distance between the front roll center and the center of gravity. This acts like a longer lever, creating more body roll, bumpsteer, and requiring additional static camber angle to maintain the same handling. The SPL front lower control arms allow the roll center to be corrected for a wide range of ride heights to improve handling and stability.

The lower control arms come with a ride height sensor bracket to maintain the factory ride height sensor location, regardless of length of the arm to keep those finicky BMW chassis electronics happy.

Benefits

Adjustable Camber, Roll Center, and Track Width

Eliminates Bushing Deflection

Improved Tire Life with Ideal Camber Settings

Lightweight, High-Strength Construction

Stackable 304SS Roll Center Spacers in 1/8" and 1/4" Sizes

US Made, PTFE Lined FK Rod Ends 

Materials

6061-T6 aluminum black anodized arm, clamps, and spacers

4130 CrMo electroless nickel-plated double adjuster

Ti6Al4V titanium socket head cap screws

304 stainless steel roll center and knuckle spacers

5/8" 4140 CrMo stud

FK PTFE-lined spherical bearings (F1 spec, self-cleaning)

Suitable for all uses, from daily driver to race car.

BMW G8X M3 M4 Rear Upper Arms are essential for maintaining optimal rear camber and minimizing tire wear for both street and track driving. The stock BMW setup can lead to excessive negative camber, especially noticeable in lowered vehicles, resulting in premature tire wear and reduced traction. These adjustable Rear Upper Arms provide a broad range of adjustment for precise rear camber alignment, crucial for both performance and longevity.

• Enhanced Camber Adjustment: Offers a wide range of adjustment for precise rear camber alignment, optimizing performance on the street or track.
• Durable Construction: Features gun-drilled 2024 Aluminum traction links and a 6061-T6 Billet Aluminum rear upper camber arm, black anodized to prevent corrosion.
• Improved Articulation: Replaces soft factory rubber bushings with smooth, Teflon-lined rod ends, eliminating bushing deflection.
• Lightweight Design: Reduces unsprung weight with aluminum components and Blue Anodized Titanium Socket Head Cap Screws.
• Easy Adjustment: Innovative 360-degree rotating clamp design and double adjuster feature allow for quick and precise camber adjustments without removing the arm.

Upgrade your BMW G8X M3 or M4 with these Rear Upper Arms for superior performance, durability, and ease of adjustment.

Enhance your BMW's handling with M7 MAXX-G Adjustable Swaybar Endlinks designed for lowered or raised MINIs. Crafted from forged SAE 4340 alloy steel, these endlinks offer superior strength and symmetry in cornering performance, allowing bind-free suspension travel and improved chassis balance. The adjustability feature ensures proper alignment, maximum grip, and neutralized sway bars for consistent balance in left and right-hand turns.

Benefits:

• Superior strength with forged alloy steel construction
• Symmetric cornering performance enhancement
• Bind-free suspension travel and better alignment
• Adjustable length for precise chassis tuning
• Corrosion-resistant black anodized finish
• Proudly made in the USA

Full set of black anodized billet sway bar end links to replace your flimsy and corroded factory units. Removable hardware for a lifetime serviceable component!

Your factory end link brackets are a one piece design with an integrated stud made of flimsy metal with no coating to protect from the elements. Over the years your end link hardware rusts right to the integrated stud and when you go to remove the end links or brackets they are one strong turn and a snap away from needing to be replaced.

Not only did ECS come up with a stronger solution with a superior resistance to corrosion but went the extra mile to incorporate hardware that can be replaced time and time again so you will never need to replace the brackets themselves. The end link brackets feature chamfers and locator pins to fit perfectly in factory location and make for a straight forward install. The brackets featuring a slotted area for the bolt head to sit so you don't have the headache of having to get a wrench in the tight space behind the bracket while installing them.

Kit Contents:

A set of front and rear end link brackets
Hardware needed for installation
Part Design:

Billet aluminum brackets
Zinc coated hardware
Superior corrosion resistance
Large upgrade from factory components

The ECS Tuning Billet Front Sway Bar Mounting Kit will provide your vehicle with a more rigid mounting solution from the sway bar to chassis than the OEM steel brackets. With an improved sway bar mounting bracket and the included polyurethane sway bar bushings you can expect to achieve an increase in rear sway bar effectiveness and less body roll as a result.

PART DESIGN

The front sway bar mounting brackets are made from a solid piece of 6061-T6 billet aluminum that are precision CNC-machined to bolt into the OEM mounting location while utilizing greaseable, polyurethane bushings. They are Type II black anodized for corrosion protection and include zinc flake coated Class 12.9 alloy steel bolts for premium performance.

The red polyurethane bushings feature a greaseable channel for extended service life and quieter operation than standard polyurethane bushings.

PERFORMANCE FEATURES

Billet & poly mounts replacing the OEM steel & rubber configuration you can expect faster reaction speed and greater effectiveness from your front sway bar due to less deflection. This translates to better handling with sharper, flatter cornering with reduced body roll.

PRODUCT DEVELOPMENT

ECS Billet Front Sway Bar Mounting Kit was designed, engineered, tested and quality inspected by the Research and Development team in our Wadsworth, Ohio facility to ensure the highest level of precision and quality is delivered throughout rigorous long term product testing and leading edge product development methods.

INSTALLATION AND SUPPORT

Installation is simple. Simply unbolt your front sway bar mounting brackets and slip over our poly bushings and billet mounting brackets with the included hardware. That's it! Enjoy better handling and a crisp front suspension.

SPECIAL NOTE: You can use any conventional automotive bearing grease for service.

Upgrade your MINI Countryman or Paceman with the Stage 1 Bundle from M7 Speed, combining industry-leading suspension components for ultimate performance. This bundle includes M7's solid billet aluminum lift kit and MAXX-G adjustable sway bar links, designed specifically for the R60 Countryman and R61 Paceman models. Enjoy enhanced road clearance, improved cornering performance, and easy installation with this comprehensive bundle.

• Stage 1 Bundle includes lift kit and adjustable sway bar links
• Lift kit raises your MINI Countryman or Paceman by 2 inches for increased road clearance
• Precision-engineered components ensure proper fitment and safe performance
• Adjustable sway bar links improve cornering performance and suspension alignment
• Easy bolt-on installation with all necessary hardware included