BMW Suspension Parts

• Compatible with most stock or aftermarket struts, including Coil Over setups
• Works with stock or lowering springs like H&R, Vogtland, or Eibach
• Significantly improves turn-in without compromising ride comfort
• Lightweight and durable aluminum alloy construction with anodized coating
• Features a replaceable spherical ball joint for durability
• Allows a 1.5-degree range of camber adjustment without affecting toe setting
• Enables quick and easy adjustment for both street and track optimization

After much anticipation, we are pleased to release our lowering spring kit for the BMW M2 G87 platform! Taking our experience from our highly popular F-chassis offerings, the goal with this offering was to lower the M2 by a tasteful amount while keeping ride quality the same or better than stock. After multiple prototypes and valuable user feedback, we believe that we met our goal. 

Our lowering springs are specifically designed to utilize the factory dampers. They are fully compatible with both standard as well as adaptive suspension. Each spring is made in the USA to our unique specifications for rates and geometries. The springs are made of high tensile chrome silicon and each unit is shot peened, pre-set, and 100% tested to ensure all the critical dimensions and rate/loads are within tolerance. The springs are then powder-coated with a stealth black finish for an OEM appearance.

Front Lowering: 1.3"

Rear Lowering: 0.75"

Stock Front Rate: 186 lb./in.

EMD Auto Front Rate: 194 lb./in.

Stock Rear Rate: 608 lb./in.

EMD Auto Rear Rate: 645 lb./in.

When an E9X is lowered beyond the limits of just lowering springs, the rear wheels toe-in excessively. This excessive rear toe leads to premature wear, that many people attribute to an increase in negative camber. It has become a common belief that an extremely low vehicle will wear the tires wrong as a matter of consequence. It has become standard practice to go as low as you can and proceed to replace your tires every five to ten thousand miles. Whats more is that when the vehicle reaches a certain ride height, the factory arms become maxed out and there is no way to compensate and dial in the proper toe. You're left with an improperly aligned vehicle that is in effect worse off than it was with the stock suspension installed.

This is not only uneconomical but improper and unsafe. ECS Tuning is proud to offer a solution for this problem in the form of Rogue Engineering E9X adjustable rear toe arms. These arms allow for greater toe adjustment on vehicles that have been lowered with a coilover suspension. With the toe set properly the tires can contact the road properly this maximizes grip and minimizes wear. 

Features:

• 100% machined and anodized, 6061-T6 lightweight aluminum arms
• High-strength, 3-piece, rod end (with carbon fiber reinforced, PTFE race) offers longer life for street compared to standard rod ends
• SEALS-IT Rod end seals keep dirt, water, and other contaminants out
• Rod ends feature grease fittings, to allow for rod end serviceability.
• Lighter than stock!  (Stock is 875g, RE arms are 640g)
• Extremely easy installation and adjustment (your alignment shop will LOVE you!)

Made from aircraft grade aluminium, with stainless steels strut inserts and hardware for the ultimate in durability for street or track use. The built in reinforcement plate reduces the stress on the shock tower to reduce the chance of the shock towers tearing. With a maximum adjustment rang of -1.5 degrees camber per side, these plates will allow you to get your suspension right where you need it. 

Fits the following BMW's:
1999-2006 E46 BMW 323i 323ci 325i 325ci 325xi 328i 328ci 330i 330ci 330xi M3

When dismantling a suspension strut sometimes the securing nut can be difficult to access and the central strut itself needs to be held still while the nut is undone. This new Shock Absorber Tool Kit is designed to overcome these problems and make the job quick and easy.

The go-through design of the sockets and ratchet design allows the strut lock extensions to go right through the middle of the ratchet and socket. Five different strut lock extensions are included, to fit a variety of applications. Seven go-through deep sockets (16, 17, 18, 19, 21, 22 and 24mm) are included, plus a sliding T-bar.

Once the spring is compressed and the top plate is free, simply choose the correct strut lock extension and socket. Then fit the socket and the ratchet handle, and fit the strut lock straight through. The central strut is held steady, and the securing nut is quickly removed.

Specifically designed for repairing and replacing shock absorbers and struts
Contents: 7 - Go Thru' deep sockets: 16/17/18/19/21/22/24mm
3 x 1/2"D Hex bits: 6mm/7mm/8mm,
1 x sliding T-bar 1/2"D,
2 x slot bit sockets 5 x 8mm, 6 x 8mm x 1/2"D
Also includes 1 x 21mm Hex Go Thru' ratchet
Packed in a blow mold case for easy storage
For California Prop 65 warning see: www.P65Warnings.ca.gov.