If you are looking for a wider range of camber adjustability in the rear of you car, the IRP Adjustable rear lower control arm is exactly what you need! Built to be much stronger than stock, these rear control arms feature inner monoball bushings and are built of steel, reducing the weight as well. These are perfect for a lowered car or for a track car that needs a greater level of rear adjustment.
Features:
This item fits the following BMWs:
1992-1999 E36 BMW 318i 318is 318ic 323is 323ic 325i 325is 325ic 328i 328is 328ic M3
1999-2006 E46 BMW 323i 323ci 325i 325ci 325xi 328i 328ci 330i 330ci 330xi M3
2003-2008 E85 BMW Z4 2.5i Z4 3.0i Z4 3.0si Z4 M Roadster M Coupe
Looking to stiffen up your rear shock mount without going for a solid rear mount? The Polyurethane Rear Performance Strut Mount from IRP will give you the stiffer reinforcement without giving you the typical noise, vibration, and harshness that come with traditional performance strut mounts. The polyurethane also helps with preventing rear shock blowouts, a common problem for stock BMW rear mounts that are paired with stiffer than stock suspension.
The bearing sleeve and poly bushing are built to work with all stock style shocks such as Bilstein and H&R coilover and suspension kits.
Fits the following BMW chassis:
E36 BMW All Submodels except for 318ti
E46 BMW All Submodels
E30 BMW All Submodels
E36 Z3 BMW All Submodels
E85/E86 Z4 BMW All Submodels
**For vehicles with coilover front suspension**
When looking to dial in your steering geometry and alignment for reduced tire where and/or better track handling, the stock suspension is quite limited. To fix this, you can install Camber/Caster plates such as these plates from IRP. Camber/Caster plates allow for adjustment of the top position of the shock's mounting position. These slight adjustments have a huge impact on the stance of the of the wheel when driving straight down the road and when turning into a corner. With simple adjustments, you can increase the grip of the tires in hard turns, improve tread life, or even just make an alignment correction for a vehicle with a lowered ride height.
The IRP Camber Caster plates are made of an aircraft grade aluminum body, for strength and low weight, with an adjustable mounting plate that utilizes a steel monoball mounting point. This makes the plate resistant to corrosion and prevents deformation even with the stiffest shocks and springs.
Features:
Fits the following BMWs:
1991-1999 E36 BMW
**For vehicles with stock style springs**
When looking to dial in your steering geometry and alignment for reduced tire where and/or better track handling, the stock suspension is quite limited. To fix this, you can install Camber/Caster plates such as these plates from IRP. Camber/Caster plates allow for adjustment of the top position of the shock's mounting position. These slight adjustments have a huge impact on the stance of the of the wheel when driving straight down the road and when turning into a corner. With simple adjustments, you can increase the grip of the tires in hard turns, improve tread life, or even just make an alignment correction for a vehicle with a lowered ride height.
The IRP Camber Caster plates are made of an aircraft grade aluminum body, for strength and low weight, with an adjustable mounting plate that utilizes a steel monoball mounting point. This makes the plate resistant to corrosion and prevents deformation even with the stiffest shocks and springs.
Features:
Fits the following BMWs:
1991-1999 E36 BMW
Enhance your BMW's performance and appearance with CTS Turbo's high-quality lowering springs. Manufactured using durable SAE 9254/DIN 54SiCr6 Spring Steel Wire, these springs guarantee safety, strength, and resistance to fatigue over time.
Lowering Specs:
Benefits:
Note: CTS suspension components should be installed by a qualified licensed mechanic experienced in suspension installations. Final ride height settles after a few days of driving.
A strut tower brace adds additional reinforcement to the front strut towers, tying them together for extra rigidity. This makes the whole structure stronger with less chassis flex. Handling and steering feel are improved with better turn-in and input with no downsides.
The IRP adjustable strut brace bar is a high quality brace that is constructed of 100% steel for guaranteed reinforcement and prevention of flex. The brace bar is painted black to ensure corrosion protection and to add to the looks of the engine bay.
Easily installed with basic hand tools.
Fits the following BMW chassis:
E46 BMW All Submodels
**For vehicles with coilover front suspension**
When looking to dial in your steering geometry and alignment for reduced tire where and/or better track handling, the stock suspension is quite limited. To fix this, you can install Camber/Caster plates such as these plates from IRP. Camber/Caster plates allow for adjustment of the top position of the shock's mounting position. These slight adjustments have a huge impact on the stance of the of the wheel when driving straight down the road and when turning into a corner. With simple adjustments, you can increase the grip of the tires in hard turns, improve tread life, or even just make an alignment correction for a vehicle with a lowered ride height.
The IRP Camber Caster plates are made of an aircraft grade aluminum body, for strength and low weight, with an adjustable mounting plate that utilizes a steel monoball mounting point. This makes the plate resistant to corrosion and prevents deformation even with the stiffest shocks and springs.
Features:
Fits the following BMWs:
1999-2006 E46 BMW
A strut tower brace adds additional reinforcement to the front strut towers, tying them together for extra rigidity. This makes the whole structure stronger with less chassis flex. Handling and steering feel are improved with better turn-in and input with no downsides.
The IRP adjustable strut brace bar is a high quality brace that is constructed of 100% steel for guaranteed reinforcement and prevention of flex. The brace bar is painted black to ensure corrosion protection.
Easily installed with basic hand tools.
*Does not fit convertible chassis"
Fits the following BMW chassis:
E36 BMW All Submodels
**For vehicles with stock style springs**
When looking to dial in your steering geometry and alignment for reduced tire where and/or better track handling, the stock suspension is quite limited. To fix this, you can install Camber/Caster plates such as these plates from IRP. Camber/Caster plates allow for adjustment of the top position of the shock's mounting position. These slight adjustments have a huge impact on the stance of the of the wheel when driving straight down the road and when turning into a corner. With simple adjustments, you can increase the grip of the tires in hard turns, improve tread life, or even just make an alignment correction for a vehicle with a lowered ride height.
The IRP Camber Caster plates are made of an aircraft grade aluminum body, for strength and low weight, with an adjustable mounting plate that utilizes a steel monoball mounting point. This makes the plate resistant to corrosion and prevents deformation even with the stiffest shocks and springs.
Features:
Fits the following BMWs:
1999-2006 E46 BMW
A strut tower brace adds additional reinforcement to the front strut towers, tying them together for extra rigidity. This makes the whole structure stronger with less chassis flex. Handling and steering feel are improved with better turn-in and input with no downsides.
The IRP adjustable strut brace bar is a high quality brace that is constructed of 100% steel for guaranteed reinforcement and prevention of flex. The brace bar is painted black to ensure corrosion protection and to add to the looks of the engine bay.
Easily installed with basic hand tools.
Fits the following BMW chassis:
E30 BMW All Submodels
ALTA Rear Control Arms are the ultimate upgrade for your MINI, replacing your rear lateral links with a solid and performance-focused design. These control arms enhance traction and handling while giving you precise control over camber and toe settings. The flexibility of ALTA control arms allows for fine-tuning without the hassle of removing and reinstalling the linkage. Simply adjust the lock nuts and twist the center section to achieve your desired settings.
These control arms are the perfect complement to other suspension products like springs, coilovers, or sway bars.
For a comprehensive rear end upgrade, consider purchasing two sets of control arms to replace both upper and lower control arms. This minimizes deflection from the OEM rubber bushings and reduces weight. Please note that on models with Xenon-style headlamps, some modifications to the leveling sensor mounting may be necessary. For additional details, consult your ALTA dealer or our Tech Department.
ALTA Rear Control Arms come with high-quality hardware, including corrosion-resistant spacers and Grade 8 adjustment nuts.
A strut tower brace adds additional reinforcement to the front strut towers, tying them together for extra rigidity. This makes the whole structure stronger with less chassis flex. Handling and steering feel are improved with better turn-in and input with no downsides.
The IRP adjustable strut brace bar is a high quality brace that is constructed of 100% steel for guaranteed reinforcement and prevention of flex. The brace bar is painted black to ensure corrosion protection.
Easily installed with basic hand tools.
*Does not fit convertible chassis"
Fits the following BMW chassis:
E46 BMW All Submodels
This product was last offered at the strikethrough price on
03-23-2026
A strut tower brace adds additional reinforcement to the front strut towers, tying them together for extra rigidity. This makes the whole structure stronger with less chassis flex. Handling and steering feel are improved with better turn-in and input with no downsides.
The IRP adjustable strut brace bar is a high quality brace that is constructed of 100% steel for guaranteed reinforcement and prevention of flex. The brace bar is painted black to ensure corrosion protection and to add to the looks of the engine bay.
Easily installed with basic hand tools.
Fits the following BMW chassis:
E34 BMW All Submodels
When an E9X is lowered beyond the limits of just lowering springs, the rear wheels toe-in excessively. This excessive rear toe leads to premature wear, that many people attribute to an increase in negative camber. It has become a common belief that an extremely low vehicle will wear the tires wrong as a matter of consequence. It has become standard practice to go as low as you can and proceed to replace your tires every five to ten thousand miles. Whats more is that when the vehicle reaches a certain ride height, the factory arms become maxed out and there is no way to compensate and dial in the proper toe. You're left with an improperly aligned vehicle that is in effect worse off than it was with the stock suspension installed.
This is not only uneconomical but improper and unsafe. ECS Tuning is proud to offer a solution for this problem in the form of Rogue Engineering E9X adjustable rear toe arms. These arms allow for greater toe adjustment on vehicles that have been lowered with a coilover suspension. With the toe set properly the tires can contact the road properly this maximizes grip and minimizes wear.
Features:
The MMX Performance adjustable drop links are a great choice for any lowered or hard-driven BMW to zero the pre-load on your anti-roll bar geometry. Plus, by replacing the stock rubber joints with motorsport-spec ball joint ends, you'll add valuable stiffness and precision to handling and steering dynamics.
The sway bar end link attaches the front anti-roll bar ends to the front damper. The OEM links were made the length they are for a reason, to complement the standard ride height.
When your ride height is altered, your vehicle's anti-roll bar ends are pulled up. With around 40mm of adjustable length, plus left and right threaded ends for easy length adjustment, the MMX adjustable sway bar end links allow you to adjust back to zero preload on your anti-roll bar - allowing it to operate exactly as it should once again.
Motorsport-spec ball joint ends using high-strength Teflon-lined steel means a much more direct response when turning into corners. By replacing the soft rubber bushing in the factory links with these motorsport-spec ball joints, cornering and steering responses are immediately sharpened. Importantly, rubber dust boots are fitted to protect the joints from road dirt and salt accumulation.
The lightweight CNC-machined T6-6061 aluminum bodies are anodized in our beautiful MMX gloss black coating to look good and stay looking good.
Features:
Manufactured in the UK from Aircraft grade T6-6061 aluminum billet.
Complete OE replacements
Anodized in signature MMX Gloss black.
Heavy-duty ball joints to ensure a long life span.
325-365mm adjustment range.
Direct replacement – can be used with either factory or Aftermarket rear anti-roll bar, and returned to standard at any time.
Designed with one aim in mind: to help achieve optimum suspension performance and geometric accuracy, and thus increase the effectiveness of your rear anti-roll bar.
Each heavy-duty, high-articulation rear end link attaches the rear anti-roll bar ends to the lower suspension arm. Replacing the failure-prone, weak plastic OEM links with our rigid billet aluminum links greatly reduces flex and allows a sharp, uncompromised transfer of suspension movement through to the sway bar.
As well as the link itself, extra stiffness and precision comes from replacing the flex-prone stock plastic ball joint with motorsport-spec ball joints. An especially valuable upgrade on older, higher mileage car.
Features:
Manufactured from Aircraft grade T6-6061 aluminum billet.
Complete OE replacements.
Our single-threaded ends make for easy length adjustment in-situ without having to detach and re-attach.
Each heavy-duty, high-articulation rear drop link.
Anodized in signature MMX Gloss black.
Heavy-duty ball joints to ensure a long life span.
Kit complete with everything you need.
Can be used with either factory or Aftermarket rear anti-roll bar, and returned to standard at any time.
Rubber boots for longevity and durability.
Updated design! Now shipping!
When an E9X is lowered beyond the limits of just lowering springs, the rear wheels toe-in excessively. This excessive rear toe leads to premature wear, that many people attribute to an increase in negative camber. It has become a common belief that an extremely low vehicle will wear the tires wrong as a matter of consequence. It has become standard practice to go as low as you can and proceed to replace your tires every five to ten thousand miles. Whats more is that when the vehicle reaches a certain ride height, the factory arms become maxed out and there is no way to compensate and dial in the proper toe. You're left with an improperly aligned vehicle that is in effect worse off than it was with the stock suspension installed.
This is not only uneconomical but improper and unsafe. ECS Tuning is proud to offer a solution for this problem in the form of Rogue Engineering E9X adjustable rear toe arms. These arms allow for greater toe adjustment on vehicles that have been lowered with a coilover suspension. With the toe set properly the tires can contact the road properly this maximizes grip and minimizes wear.
Features:
100% machined and anodized, 6061-T6 lightweight aluminum arms (and collars).
Stainless hardware and spacers are perfect for the tough Northeast climate!
New! Easy adjustment with 22mm open ended wrench and 5mm allen key! It only requires 15 ft. lbs. on the clamp to secure the clamp!
New! Included lock-out kit, replaces factory eccentric hardware.
Updated 3-piece rod ends features 4130 chromoly steel bodies, heat-treated, alloy steel races, and Teflon liners
Extremely easy installation and adjustment (your alignment shop will LOVE you!)
Want the best performance option in shock tower mounts? IRP has created their pillow-ball rear shock mounts for just this need. These rear shock mounts are designed for use on the track and racing. This set of mounts will help your rear shocks perform the best they can in all conditions. The advantage to using a mount with spherical bearing is that it allows the shock to freely move off axis without side loading the shock shaft like rubber or polyurethane mounts do. Side loading a shock increases stiction and wear which decreases its efficiency. Because these are mounts without an isolator (rubber or polyurethane) to dampen road noise and vibrations we do not recommend them for street cars.
The bearing sleeve and poly bushing are built to work with all stock style shocks such as Bilstein and H&R coilover and suspension kits.
Fits the following BMW chassis:
E36 BMW All Submodels except for 318ti
E46 BMW All Submodels
E30 BMW All Submodels
E36 Z3 BMW All Submodels
E85/E86 Z4 BMW All Submodels
Looking to upgrade your front suspension to increase the strength and your steering angle for the track? IRP has you covered with their BMW Lock Kit. This kit includes new control arms that are stronger than stock and have monoball ball joints, new tie rod ends that feature steel monoball ball joints as well, new offset control arm bushings, fully adjustable camber plates, roll center/bump steer correction plates, and all new hardware. This enables this kit to be fully plug and play, giving you a much more adjustable front suspension, and increases the total amount of steering angle up to 65 degrees.
This kit is perfect for those looking to build a drift car and ensure their suspension is ready to take on the challenge.
Kit features:
Fits the following BMWs:
1999-2006 E46 BMW All Non-M RWD Submodels
A strut tower brace adds additional reinforcement to the front strut towers, tying them together for extra rigidity. This makes the whole structure stronger with less chassis flex. Handling and steering feel are improved with better turn-in and input with no downsides.
The IRP adjustable strut brace bar is a high quality brace that is constructed of 100% steel for guaranteed reinforcement and prevention of flex. The brace bar is painted black to ensure corrosion protection and to add to the looks of the engine bay.
Easily installed with basic hand tools.
Fits the following BMW chassis:
E36 BMW All Submodels
A strut tower brace adds additional reinforcement to the front strut towers, tying them together for extra rigidity. This makes the whole structure stronger with less chassis flex. Handling and steering feel are improved with better turn-in and input with no downsides.
The IRP adjustable strut brace bar is a high quality brace that is constructed of 100% steel for guaranteed reinforcement and prevention of flex. The brace bar is painted black to ensure corrosion protection.
Easily installed with basic hand tools.
*Does not fit convertible chassis"
Fits the following BMW chassis:
E30 BMW All Submodels
MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.
MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.
Enhance your BMW's performance and aesthetics with CTS Turbo's high-quality lowering springs. Crafted from durable SAE 9254/DIN 54SiCr6 Spring Steel Wire, these springs ensure safety, strength, and long-term durability.
Key Features:
Lowering Specs:
Featured Advantages:
Notes:
