BMW Suspension Parts

The B16 PSS10 coilovers offer a stiffer spring rate than stock and a lower ride height for less bodyroll and better handling. These are among the easiest coil over kits on the market - no special mounts required (works with stock mounts and sway bar links), larger adjustment knob allows for easy shock damping changes, and coil over spanner wrenches included for easy height changes. Bilstein backs up their technology with a limited lifetime warranty. TUV approved for fitment, safety, and quality!

Bilstein's monotube shock dampers in the PSS10 offer 10 precise settings for compression and rebound. A new setting is just a click away, allowing you to set a ride and handling combination that works for your setting. Instead of offering too many shock settings that you're never going to use, Bilstein has chosen ten optimal damping curves from a smooth street setting (P10) to an ultra-stiff track-only setup (P1). Shock changes are made from an easy-to-use over-sized adjuster knob.

Ride height adjustments are done from perches that ride on each shock body, which are zinc coated for excellent wear and corrosion resistance. You can set the ride height between 0.5 to 1.3 inches lower than stock ride height. Springs are progressively rated so their initial compression rating is quite soft and then becomes stiffer as the spring compresses. These are stiffer than most coil over kit manufacturers and the results of Bilstein's extensive testing on the German Nurgburgring and Autobahn.

The fitment of these is just like a standard shock and spring package. The front struts and rear shocks are compatible with the stock strut and shock mounts. You can re-use your own or choose a mount with additional features. Because the Bilstein design keeps the sway bar tab in the original location, you can re-use the stock sway bar links. Using the stock mounts keeps the cost and complexity down and allows for TUV certification. You can also be assured of the stock mount's quiet and long-lasting performance. The assembly of the front strut is the same as a the factory strut. In the rear, ride height is made by an adjustable spring perch that sits under the rear spring. Install instructions and diagrams included.

If you're looking for a supremely capable and high quality suspension, then look no further than the Bilstein PSS10. It combines all of the best German engineering with real-world development, and a lifetime warranty.

Fitment note: this system works only on cars not equipped with the factory EDC electronically adjustable shocks.

Featuring:

• Largest available piston diameter for greater sensitivity and precise control.
• Patented digressive piston head design and deflective valving instantly reacts to changing road conditions.
• 10-way adjustable dampening knobs that "click" from soft to hard with no tools or jacking required.
• Monotube design dissipates heat more effectively than a twin tube shock for cooler, more efficient operation and longer life.
• Weather resistant coating to resist oxidization, and ensure long life.
• Lighter weight reduces wear and tear on suspension components.
• Wrenches to adjust front and rear ride height included!

This coilover kit fits the following BMWs:
2008+ E82 BMW 128i 135i
2006+ E90 BMW 325i 328i 330i 335d 335i
2007+ E92 BMW 328i 335i 335is
2007+ E93 BMW 328i 335i

Remove and install the three bushings and ball joints that are pressed into the rear trailing arm. Use this one tool kit for on-vehicle or off-vehicle removal and replacement of the Rear Trailing Arm Bushing, Outer Upper Control Arm Bushing (ball joint) and Outer Lower Control Arm Bushing (ball joint). This tool is designed to work on E36 3-series (except E36 318ti), E46 3-series, E83 X3 and E85/E86 Z4 Coupe & Roadster.

From 1974 to 2019, Bavarian Autosport was one of the premier vendors for BMW and MINI auto parts. We are happy to preserve the Bav Auto legacy by continuing to carry their high-quality products into the future. All Bav Auto parts will remain unchanged in design and sourced from the same OEM suppliers to ensure long-lasting reliability. We trust these parts, accessories, and upgrades so confidently that we back every Bavarian Autosport branded component with a 2-year warranty.

For all 2001 to 2005 325xi and 330xi. For convenience, we have assembled this bushing carrier bracket kit, to save you time when changing our control arm bushings. It includes two bushing carriers with pre-installed bushings (one left, one right) and mounting bolts.

 These bushing brackets fit all 2001, 2002, 2003, 2004, and 2005 model BMW 325xi and 330xi.

This kit is contains all new strut and shock mounts and hardware needed when installing a aftermarket suspension on your vehicle. 

Fits the following BMW's

E46 323ci 323i 325ci 325i 325xi 328ci 328i 330ci 330i 330xi 

Eliminate the most common sources of suspension slop with our all new Turner Suspension Refresh Kits that feature only OEM parts! We do not include any "cheap parts" in our refresh kits to ensure long-lasting reliability and noise-free suspension.

This Level 1 kit replaces:

Front Control Arms
Front Control Arm Bushings
Front Sway Bar End Links & Bushings
Front Ball Joints
New Hardware

Replacing your struts and shocks? Don't forget the bushings! The rubber mounts for the shocks will go bad over time, especially if you drive hard or the roads are particularly rough. The shock mounts locate the front struts and rear shocks to the car - providing a quiet and vibration-free buffer between the road and the cabin. Shock mounts and bushings can wear out just like any other rubber part on the car. This leads to more noise and harshness reaching the chassis and may complicate your new suspension install. When installing new shocks, that is the perfect time to also replace the mounts. There is no additional time to install them, no special tools required, and doesn't take any extra time! If you re-use the original mounts you have the risk of them failing before your next shock replacement, doubling your labor costs. 

This item fits the following BMWs: 
2006-2012 E9X BMW All xi models - 325xi 328xi 330xi 335xi

Eliminate the most common sources of suspension slop with our all new Turner Suspension Refresh Kits that feature only OEM parts! We do not include any "cheap parts" in our refresh kits to ensure long-lasting reliability and noise-free suspension.

This Level 1 kit replaces:

Rear Sway Bar End Links
Rear Trailing Arm Bushings
Rear Strut Mounts
New Hardware

Eliminate the most common sources of suspension slop with our all new Turner Suspension Refresh Kits that feature only OEM parts! We do not include any "cheap parts" in our refresh kits to ensure long-lasting reliability and noise-free suspension.

This Level 1 kit replaces:

Rear Sway Bar End Links
Rear Trailing Arm Bushings
Rear Strut Mounts
New Hardware

Eliminate the most common sources of suspension slop with our all new Turner Suspension Refresh Kits that feature only OEM parts! We do not include any "cheap parts" in our refresh kits to ensure long-lasting reliability and noise-free suspension.

This Level 2 kit replaces:

Suspension Bushings
Control Arm Bushings
Hardware
Rear Shock Mounts
Control Arms & Trailing Arms

Eliminate the most common sources of suspension slop with our all new Turner Suspension Refresh Kits that feature only OEM parts! We do not include any "cheap parts" in our refresh kits to ensure long-lasting reliability and noise-free suspension.

This Level 2 kit replaces:

Front Sway Bar End Links
Front Upper Strut Mounts
Control Arms w/ Bushings
Control Arm Brackets w/ M3 Control Arm Bushings
Outer Tie Rods

Eliminate the most common sources of suspension slop with our all new Turner Suspension Refresh Kits that feature only OEM parts! We do not include any "cheap parts" in our refresh kits to ensure long-lasting reliability and noise-free suspension.

This Level 1 kit replaces:

Front Control Arms
Control Arm Bushings
Sway Bar End Links
Sway Bar Bushings
Headlight Level Sensor Rod

Eliminate the most common sources of suspension slop with our all new Turner Suspension Refresh Kits that feature only OEM parts! We do not include any "cheap parts" in our refresh kits to ensure long-lasting reliability and noise-free suspension.

This Level 2 kit replaces:

Front Strut Mounts
Control Arms
Outer Tie Rods
Sway Bar End Links

Eliminate the most common sources of suspension slop with our all new Turner Suspension Refresh Kits that feature only OEM parts! We do not include any "cheap parts" in our refresh kits to ensure long-lasting reliability and noise-free suspension.

This Level 1 kit replaces:

Front Control Arms
Front Control Arm Bushings
Front Ball Joints