BMW Drivetrain Parts

Schwaben offers the right tools to make your next project a success. Everything from complex engine scanners to brake bleeders and spring compressors, Schwaben tools has you covered.

Some of the recommended use include but are not limited to:

• Remove and install rear ball joints on E38, E39, E60/61, E63/64, E65/66, and E70's
• Removal and installation of ball joints and bushings on rear control arms on E36, E46, E39, E60/61, E63/64,  E65/66, E70, E83 and E85/86 Z4's
• Removal and installation of rear sub frame mounted differential bushings on E36, E46, E83 and E85/86 Z4's
• Removal and installation of rear differential mounted bushings on E36, E46, E9X, E60/61, E63/64, E65/66, and E85/86 Z4's

Installing wheel bearings correctly can prove to be a difficult task. With the compression fitting in the race, it makes it possible to install it without it being plumb. Well, we have your solution. With this specialty tool from BMW, you can ensure that your wheel bearing is installed correctly every time. 

Comparable to OE tool 83300491905. 

Ensure precise clutch installation with this specialized alignment tool, designed specifically for N54-equipped BMWs. While most aftermarket clutch kits include a generic alignment tool, many are intended for the N55, which is incompatible with the N54 due to differences in pilot bearing mounting and flywheel design.

This tool is engineered for both 6-bolt (01/2009+) and 8-bolt (-01/2009) N54 flywheels, allowing you to accurately center and align the clutch disc on the flywheel during pressure plate installation. Achieve a hassle-free and precise fit with this essential service tool.

This hand held Schwaben tool makes changing fluids an easy, quick task.The Schwaben fluid suction/fill pump suitable for oils, water and any non corrosive liquid.

Features 

• Comes with a flexible and a rigid tube. 
• Flow rate is adjustable for different functions.
• 350 ML capacity
• Cylinder is marked in 20 mL increments and fraction of quarts for accurate filling. 

Not for use with gasoline.

• 30% shorter shifts
• Counterbalanced for great shift feel
• Stainless steel & aluminum construction
• Rubber isolated for reduced NVH
• Maintains stock shift feel with uprated stock-type bushings

The Dinan short shifter provides shorter shift throws with a crisper and more precise feel than a stock shifter. Instead of retrofitting a stock BMW lever, with all of its deficiencies, Dinan has engineered this billet aluminum shifting system. Special features engineered into this unit include a two piece fully isolated stick assembly, exclusive integrated and dampened pivot cup with self lubricating pivot ball, counter balanced to reduce effort and exclusive polymer "Iglide" T-500 lower pivot bushings that are impervious to contamination. Featuring an adjustable pivot, which allows this shifter to fit both standard and M Series applications. All of this combined with a simple straightforward installation provides a professional level shifter. Provides a 30% throw reduction in E82 128i/135i, E9X 325i/328i/330i/335i, and E60 530i/545i/550i.

For over 35 years, Dinan has been America's premier tuning company, pioneering advancements in BMW modification while retaining a focus on balanced performance that preserves the original character and driving feel that a BMW offers. When you install a Dinan part on your car, know that it's not only carefully developed and tested, but that Dinan stands behind it with a four year, 50,000-mile warranty.

The Pneumatic CV Boot Installer simplifies CV boot installation through air power. Its sturdy metal fingers stretch the boots, enabling effortless slipping over constant velocity joints without the need to remove them from the axle.

This efficient tool reduces the once time-consuming two-hour task to a mere 20-minute job, saving significant labor and effort. Operating it is a breeze?all you need is an air compressor, making it convenient for both professionals and enthusiasts in the automotive industry.

Crucially, it works exclusively with flexible CV boots, and is not compatible with plastic boots. With its user-friendly design, this installer is a game-changer in automotive maintenance, offering a hassle-free solution for CV boot installation.

Plus, our Air Powered CV Boot Installer comes with a LIFETIME REPLACEMENT guarantee, ensuring you never have to worry about spending hours on boot installations again!

Elevate your lifting experience with the Schwaben Long Low Profile - High Lift Floor Jack. Certified for excellence and designed with a keen understanding of European car enthusiasts' needs, this jack is a testament to precision, durability, and performance. Don't compromise on quality—choose the Schwaben advantage for all your lifting endeavors.

Designed with precision, crafted for performance, and backed by our lifetime replacement program, the Schwaben Long Low Profile - High Lift Floor Jack is a must-have tool for every European car aficionado. This jack is engineered to cater to the unique needs of low ground clearance vehicles, ensuring that your prized possessions are lifted with care and precision.

Key Features:

• One Pump Reach: With its innovative one-pump feature, this floor jack effortlessly reaches contact on most cars, streamlining your lifting process.
• Low Profile Advantage: Boasting a mere 2-3/4" low height and a deep-reach lift arm, this jack is tailored for those sports cars and luxury vehicles that ride close to the ground.
• Hydraulic System Protection: The dual pump pistons are expertly shielded to thwart contaminants from compromising the hydraulic system's integrity.
• Built for Durability: Crafted with heavy gauge construction and fortified with rolled edges, this floor jack guarantees unwavering strength and longevity.
• Precise Control: The U-Joint release mechanism offers meticulous control over load descent at any handle position, ensuring the safety of both you and your vehicle.
• Maneuverability Redefined: Upgraded casters allow seamless maneuverability and effortless positioning of the jack, empowering you to find that perfect lifting spot.
• Safety First: The internal by-pass valve prevents over-pumping, shielding the hydraulic system from stress-induced issues.
• Vehicle Protection: A full cover rubber saddle pad and a protective foam cover on the handle are in place to prevent any unintended damage during the lifting process.
• Impressive Capacity: With a remarkable 4000 lb. capacity, this jack is ready to tackle a range of European vehicles.
• LIFETIME REPLACEMENT: Like almost all Schwaben products, this jack is backed by our lifetime replacement program in case anything goes wrong!

Specifications:

• Min Height: 2-3/4"
• Max Height: 24"
• Handle Length: 49-1/4"
• Jack Body Length: 35"
• Length from Pivot Point to Center of Jack Pad: 22"
• Front Casters: 2-1/2" diameter x 2" width
• Saddle Diameter: 4" with full saddle pad
• Weight Capacity: 4000 lbs.
• ANSI / ASME PALD 2009 Certified

Also included are the Schwaben Aluminum 3-Ton Jack Stands. These ultra-light Schwaben jack stands only weigh 4.7 lbs each. Fit and finish on these stands show how much pride in workmanship goes into our stands. These stands feature all-aluminum construction with heavy-duty flanged bases to safely stabilize loads. Features 6 locking positions for a secure load in multiple heights. The load pin is extra heavy duty at .584 in. diameter and features a posi lock ball to ensure the pin stays in place.  

• Min. Height is 10.6".
• Max Height is 15.4".
• Large 7" diameter base.
• Outer support tube is 2-1/8" in diameter.

For replacement parts, please call us and ask for:

• ES#4430428 - Replacement Screw Set
• ES#4430429 - Replacement Front Wheel
• ES#4430430 - Replacement Caster Wheel

WARNING: This product contains chemicals known to the state of California to cause cancer, birth defects, and/or reproductive harm. See above warning label as well as http://www.p65warnings.ca.gov for further information on Proposition 65 warnings.

BMW E36 328i, Z3 2.8 JB Racing Lightweight Aluminum Flywheel offers a significant performance upgrade by replacing the heavy stock steel flywheel with a much lighter aluminum version. This JB Racing flywheel is designed to deliver faster acceleration, improved throttle response, and enhanced overall performance for your BMW.

The modern stock flywheels are burdened with additional components meant to dampen vibrations, which unfortunately adds unnecessary weight. The JB Racing aluminum flywheel, weighing just 10.0 lbs compared to the stock 25.0 lbs, eliminates this excess mass, allowing more power to reach the wheels and reducing the energy wasted on spinning the flywheel. Engine builders prioritize lightweight flywheels when optimizing race engines for maximum efficiency, and the difference is especially noticeable in how quickly the engine revs and reaches its power band.

This JB Racing lightweight flywheel is a direct replacement for the stock flywheel and is compatible with the factory BMW organic clutch. This compatibility ensures that you can use standard replacement clutches, making maintenance simple and cost-effective. The flywheel can also be resurfaced for a fresh contact surface, so there’s no need to buy a new one when it’s time to replace the clutch.

While single-mass aluminum flywheels like this one may result in slightly more noise and vibration compared to dual-mass designs, this can be managed with heavier transmission oil and sprung hub clutches, such as the Sachs Performance clutch available through Turner Motorsport.

• Faster acceleration: Reduces the rotational mass for quicker engine response.
• Improved throttle response: Engine revs more freely and builds RPM faster.
• Enhanced performance: More power delivered to the wheels for better driving dynamics.
• Cost-effective maintenance: Compatible with factory BMW organic clutches and can be resurfaced.
• Direct replacement: Easy upgrade with no modifications required.

Vehicle Compatibility:

• 1996-1999 E36 BMW 328i, 328is, 328ic
• 1997-1998 Z3 BMW Z3 2.8