BMW Engine Parts

Maintaining optimal engine oil levels is crucial for peak performance in your BMW. Leaks can occur between oil change intervals, leading to dangerously low oil levels. The valve cover is a frequent culprit for such leaks due to gasket degradation from years of exposure to temperature fluctuations. Replace your valve cover to ensure the retention of engine oil within your vehicle.

Key benefits of replacing the valve cover include:

• Preventing oil leaks that could lead to low oil levels.
• Preserving engine performance and longevity.
• Avoiding potential engine damage from insufficient oil.

Ensure your BMW's engine operates smoothly by replacing the valve cover to contain the engine oil effectively.

If oil is leaking from the seal at the oil pan and block, you will need a new oil pan gasket. It is also wise to change this any time you have to pull the oil pan gasket.

Elring is one of the biggest OEM names in the manufacturing of high quality gaskets that are available for very affordable prices. Elring has supplied many automotive names for years with the gaskets that seal your car's components from day 1 so you can rest assured that these components will last for a long time to come!

Fits the following BMW engines:
N52 3.0L
N54 3.0L

If there is a large amount of oil on the sides of the engine or if you can smell burning oil, chances are it's a bad valve cover gasket. The gasket fails and allows oil to seep down onto the side of the engine and other parts causing a mess and reducing the amount of oil in your engine. This replacement gasket from Elring is perfect to prevent any further oil leaks.

Elring is one of the biggest OEM names in the manufacturing of high quality gaskets that are available for very affordable prices. Elring has supplied many automotive names for years with the gaskets that seal your car's components from day 1 so you can rest assured that these components will last for a long time to come!

Fits the following BMW engines:
N54 3.0L

BMW's Single-VANOS M52 and S52 engines were equipped with plastic valve covers from the factory. Nearing thirty years post-production, this material choice has proven to be problematic. Due to years of exposure to extreme engine temperatures and chemical-rich engine oil, these plastic valve covers will eventually warp. This results in a valve cover that will not seal, requiring a complete replacement of both the plastic valve cover and associated gaskets.

To remedy this, many enthusiasts opt to swap for the magnesium valve cover found on M50 and S50 engines. Unfortunately, magnesium is no less resistant to heat-induced warpage than plastic.

Thankfully, Bremmen Parts is aware of these issues and has created an exact-fit, high-quality performance replacement for all Single-VANOS M52 and S52-equipped BMWs. This cover features durable aluminum construction, which eliminates the warping issue found on OE plastic and magnesium valve covers. Unlike the OE magnesium cover upgrade, Bremmen's aluminum cover retains the forward oil fill location found, allowing you to retain your existing engine beauty cover.

Whether you're replacing a warping plastic cover or preemptively replacing this failure-prone component, Bremmen has you covered with a direct-fit aluminum valve cover upgrade.

If you're experiencing hard starting, flaky charging, or other electrical issues, your engine ground strap may be the culprit. On E9X BMWs, the engine ground strap is a thin, non-insulated cable that spans from the left engine mount arm to the frame horn. Despite the seemingly simple nature of this part, on older cars, it is known to cause massive headaches. Due to its non-insulated design, years of exposure to water, dirt, and road salt will cause the wire to corrode, ultimately leading to complete failure. A break in this cable will cause an open circuit, resulting in issues with the vehicle's electrical system and potentially leading to a no-start condition.

To solve this issue, ECS has engineered an exact-fit, upgraded ground strap for your E9X BMW! Unlike its OEM counterpart, this design features insulated, large-gauge copper wire for dependable conductivity and long-lasting durability. Additionally, factory-style lugs are zinc-coated, crimped, and soldered, ensuring protection against corrosion and oxidation.

Whether you're replacing a visibly corroded strap or proactively preventing failure, this solution from ECS is sure to provide lasting performance and protection.

FEATURES

Direct-fit replacement and upgrade for RWD E82/E88, E84, and E9X applications Solves intermittent grounding issues caused by aging OEM straps Clean, stealthy design that fits seamlessly in factory engine bays Factory length and lug orientation for drop-in fitment 2 AWG tinned copper cable for excellent conductivity and corrosion resistance Zinc-coated lugs, crimped and soldered to resist moisture and oxidation Black UL1015-grade insulation withstands oil, heat, and abrasion Discreet ECS label for a clean, OEM+ look Replaces OEM part numbers 12427549393, 12427795404, and 12427790559.

The N54 suffers from a weak point in its crankshaft. It has been reported that when increasing the power to the engine, the crank hub can move or spin slightly under an extreme load. This is most apparent under high-rev downshifts or in the case of increased boost pressure which creates more stress on the engines rotating assembly. In order to keep this from happening, the crank bolt must be secured to the hub to keep it from backing off, but this can be a tricky solution since a simple dab of Loctite will not suffice. 

Here is an easy, and cost-effective way to secure the situation; The VTT N54 crank bolt capture. This lightweight and durable ring slips over the head of the crank bolt fully encapsulating it, and locks it to the crank hub and eliminating its ability to spin. The VTT-CBC is 100% Billet Aircraft Grade Aluminum, Anodized black to protect it from the elements, and give it a stealth look. What's more is that it weighs only 1.3 Oz's meaning you aren't adding excess mass to the crankshaft which will avoid any imbalance or vibration issues.

While this is not a full fix for all crank hub spinning issues, the engineers at Vargas have found most issues have stemmed from the bolt itself backing out, and this is a great way to keep that from happening. Extremely lightweight at only 1.3 Oz's it adds virtually no weight to the crank which is important for balance and vibration.

Kit Includes:

• 1x Aluminum Crank Bolt Capture
• 8x Fasteners Gr. 12.9

This part fits the following BMWs:
2006-2013 N54