Find Parts That Fit Your Vehicle

BMW Engine Parts

Turner Motorsport has everything you need to upgrade your BMW through our stages of performance or to keep your car in peak condition with our range of the latest in proven OEM cooling parts. Upgrade your cooling system and engine performance with the selections below to give your BMW a performance and reliability advantage.

Sub-Categories

Sort By:

Macht Schnell - Corporate Logo
T#:593749
Part#: 10.00.011
In Stock
$ 349.00 USD
Free Shipping
$ 349.00 USD
Free Shipping
Free additional power to your M3’s rear wheels without sacrificing or compromising your BMW’s reliability. Machined from 6061-T6 aerospace aluminum, Macht Schnell Performance Underdrive Pulleys are strong as well as lightweight to limit parasitic drag from the accessories within a moderate level for maximum performance on or off the track. After machining and engraving, pulleys are then T3 hard anodized for additional strength, anti-corrosion & wear resistance. Our DualDrive design replaces the Crank Accessory & Power Steering Pulleys, resulting in an additional 9-14 HP and 7-9ft. lbs TQ gain for the M3. Gains are due to a reduction in power required to turn accessories; an increase in accessories lifespan due to lower speed will also result. All factory harmonics/balancing are undisturbed. Macht Schnell Performance Underdrive Pulleys have no negative effect on accessory operation and comes fully equipped with new belts. Already have this kit and need new belts? See T#14491 and T#14489 Performance Underdrive Pulleys Features: DualDrive design allows maximum performance, with minor effect on accessory speed Proper cooling temperatures are retained at proper levels on or off the track Maintains proper alternator speed, allowing sustained levels to sensitive control modules Machined from 6061-T6 aerospace aluminum T3 Hard-Anodized for maximum strength and corrosion/wear resistance No affects to crankshaft dampening or harmonics Simple bolt-on installation
Show More Show Less
Mishimoto - Corporate Logo
T#:380389
Part#: MMOCF-BMW
In Stock
$ 88.99 USD
Free Shipping
$ 88.99 USD
Free Shipping
Install a custom oil cooler on your street or track BMW with help from the Mishimoto Oil Line Fitting Kit! This kit has 100% CNC-machined components, including the 6061 aluminum oil line fittings and the 303 stainless steel tie-down plate. This adapter kit is applicable for BMW E36 (Euro oil-housing equipped), E46, and E90 vehicles, and allows for the use of -10AN fittings to route oil to a custom oil cooler setup. This is an ideal upgrade for drivers seeking additional cooling for track environments or for those who would like additional engine bay space for an oil accumulator or supercharger setup. Included in this kit are two stock BMW O-rings for leak-free installation. Features: Allows for use of -10AN fittings for custom oil cooler setup 100% CNC-machined components, including 6061 aluminum fittings and 303 stainless steel tie-down plate Includes durable stock BMW O-rings for leak-free installation Provides additional engine bay space for applications with an oil accumulator or supercharger setup Included as part of the Mishimoto BMW E46 M3 Oil Cooler Kit Mishimoto Lifetime Warranty Included: (1) Stainless Steel Fitting Clamp (2) -10AN Fittings (2) BMW Oil O-rings (1) M8 x 1.25 x 25mm Button-Head Bolt Mishimoto Lifetime Warranty WARNING! Prop 65 may apply to this product. Proposition 65 (Safe Drinking Water and Toxic Enforcement Act of 1968) is a California law that applies to call companies selling products in California. Prop 65 requires any listed chemical present above very low levels that are known to cause cancer, birth defects, or other reproductive harm. For more information about California Prop 65 warning see: www.P65Warnings.ca.gov. ​
Show More Show Less

Mishimoto - Corporate Logo
T#:597051
Part#: MMOCCLA
In Stock
$ 127.99 USD
Free Shipping
$ 127.99 USD
Free Shipping
WARNING! Prop 65 may apply to this product. Proposition 65 (Safe Drinking Water and Toxic Enforcement Act of 1968) is a California law that applies to call companies selling products in California. Prop 65 requires any listed chemical present above very low levels that are known to cause cancer, birth defects, or other reproductive harm. For more information about California Prop 65 warning see: www.P65Warnings.ca.gov.
Show More Show Less

Mishimoto - Corporate Logo
T#:637363
Part#: MMBCC-F80-15CBE
In Stock
$ 306.99 USD
Free Shipping
$ 306.99 USD
Free Shipping
Give your 2015–2020 BMW M3/M4 the protection it deserves with the Mishimoto Baffled Oil Catch Can Kit. The introduction of the S55 into the M3 and M4 in 2015 was the first time compact M’s saw turbos from the factory, but these engines brought along another long-standing tradition—blow-by. The Mishimoto BMW M3/M4 catch can kit uses proven engineering from the patent pending Mishimoto 2-Port Compact Baffled Oil Catch Can, with its 50-micron bronze filter and internal baffle, to better separate the oil from the crankcase vapors. The engineers at Mishimoto designed a CNC-machined lid that features large inlet and outlet ports to match the inner dimension of the CCV hose. This baffled oil catch can defends your intercooler, intake system, and VANOS system from oil blow-by and helps maintain proper octane levels to reduce potential detonation. The kit comes with two direct-fit hoses, which require no modification to the engine cover, and one direct-fit billet aluminum mounting bracket that is extremely easy to install and mounts the can in a serviceable location! Two aluminum, 3/4” barb fittings connect the hoses to the can. And, like every Mishimoto oil catch can, this baffled catch can kit comes with the Mishimoto Lifetime Warranty! Our catch cans are different from most air-oil-separator (AOS) systems on a few levels. First, our catch cans are not heated. This means that all of the blow-by is able to condense in the can, including low-octane oil vapors and contaminated fuel vapors. Most AOS systems also drain the blow-by back into the oil pan, while our catch cans trap the blow-by and keep it out of the engine permanently. If you’ve seen what we’ve seen in the bottom of our catch cans, you won’t want that draining back into your oil either. *After installation, Mishimoto recommends checking the contents of the baffled catch cans every 1,000 miles until a baseline is established. Oil blow-by accumulation will vary with ambient temperatures and driving conditions. It is important that the contents of the can do not rise above the internal baffle* Features: Direct fit for the 2015–2020 F8X BMW M3 and M4 Single can mounts in line with the CCV system to separate oil from air using a 50-micron bronze filter Helps reduce carbon buildup on intake valves Patent-pending billet 6061 aluminum can sealed with Viton™ O-rings Installs in under 30 minutes Robust CNC-machined anodized aluminum bracket mounts the can in a serviceable location Includes pre-molded hoses for simplified installation Defends Vanos system and essential engine components from oil blow-by CNC-machined aluminum barbed fittings ensure a sturdy connection between lines and can Catch can has a 3 oz. capacity for longer servicing intervals Internal air diverter increases air turbulence to improve oil separation Helps maintain proper octane levels to reduce potential detonation Filter and can are fully serviceable Mishimoto Lifetime Warranty Included: (1) Compact Baffled Oil Catch Can (1) Application-Specific Mounting Bracket (2) Direct-Fit Hoses (2) 3/4" Aluminum Barbed Fittings (4) Worm Gear Clamps Mounting Hardware Mishimoto Lifetime Warranty WARNING! Prop 65 may apply to this product. Proposition 65 (Safe Drinking Water and Toxic Enforcement Act of 1968) is a California law that applies to call companies selling products in California. Prop 65 requires any listed chemical present above very low levels that are known to cause cancer, birth defects, or other reproductive harm. For more information about California Prop 65 warning see: www.P65Warnings.ca.gov.
Show More Show Less
Mishimoto - Corporate Logo
T#:637357
Part#: MMOC-F80-15
Ships in 3 Business Days
$ 609.99

This product was last offered at the strikethrough price on
08-13-2026

$ 549.99 USD
Free Shipping
$ 549.99 USD
Free Shipping
Add some much-needed durability and cooling power to your M3 or M4 with the Mishimoto 2015-2020 BMW M3/M4 Oil Cooler. True to form, the engineers at BMW designed the M3/M4’s oil cooler with efficient use of space in mind. Suspended perpendicular from the rest of the cooling stack, this location utilizes the Bimmer’s aerodynamics in order to cool the oil, all while putting the lightweight, tube-and-fin cooler in harm's way of road hazards. We here at Mishimoto made sure to beef up the oil cooler design for the F80/82 with our performance oil cooler. We ditched the lightweight design for a full aluminum, TIG-welded bar-and-plate cooler for added strength and cooling. The bars and plates are a much more robust form of heat exchanger core construction intended for improved heat transfer and have the strength to shrug off potential road debris, keeping your oil temps down, and where it should be. We also added 10mm to the core’s thickness, equating in a 46% increase in core volume, and increased the oil capacity by .4 qt. The Mishimoto 2015-2020 BMW M3/M4 Oil Cooler fits directly in place of the stock unit, and includes the Mishimoto Lifetime Warranty for a simplified and worry-free installation. Features: Direct fit for the 2015–2020 BMW F8X M3, M4, and M2 Competition Full aluminum TIG-welded construction 46% increase in core volume Increases oil capacity by .44 quarts Robust bar-and-plate construction for improved durability and heat rejection Silver powder-coated finish for maximum protection No cutting or modifications required Mishimoto Lifetime Warranty Included: (1) Performance Oil Cooler (2) Replacement O-Rings Mounting Hardware Mishimoto Lifetime Warranty WARNING! Prop 65 may apply to this product. Proposition 65 (Safe Drinking Water and Toxic Enforcement Act of 1968) is a California law that applies to call companies selling products in California. Prop 65 requires any listed chemical present above very low levels that are known to cause cancer, birth defects, or other reproductive harm. For more information about California Prop 65 warning see: www.P65Warnings.ca.gov.
Show More Show Less

Beru - Corporate Logo
T#:584875
Part#: 12218591724
In Stock at Vendor
$ 185.00

This product was last offered at the strikethrough price on
08-13-2026

$ 129.99 USD
Free Shipping
$ 129.99 USD
Free Shipping
Sends power to the glow plugs to preheat them for ignition.

Mishimoto - Corporate Logo
T#:372557
Part#: MMOCCCF
In Stock
$ 162.99 USD
Free Shipping
$ 162.99 USD
Free Shipping
Universal kit with a catch can and rubber hose; for retrofitting on a variety of vehicles. Carbon fiber catch can prevents a harmful buildup of oil inside of the turbocharger, intake manifold, intercooler and piping. Separates oil particles from PCV/CCV air Defends intercooler, intake system, and essential components from oil blow-by Made from lightweight carbon fiber Compact design makes for easy engine bay placement Checking fluid levels made easy with built in sight tube Comes complete with mounting bracket, hose, all necessary clamps, fittings, and mounting hardware Mishimoto Lifetime Warranty WARNING! Prop 65 may apply to this product. Proposition 65 (Safe Drinking Water and Toxic Enforcement Act of 1968) is a California law that applies to call companies selling products in California. Prop 65 requires any listed chemical present above very low levels that are known to cause cancer, birth defects, or other reproductive harm. For more information about California Prop 65 warning see: www.P65Warnings.ca.gov.
Show More Show Less

NOCO - Corporate Logo
T#:641140
Part#: GENIUS5
Ships in 8 Business Days
22% off MSRP $ 89.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 69.99 USD
Free Shipping
22% off MSRP
$ 89.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 69.99 USD
Free Shipping

The GENIUS5 is an exceptional addition to our lineup boasting incredible power, top-notch performance, energy efficiency, and a compact design. The GENIUS5 is a versatile 6-volt and 12-volt charger, maintainer, and desulfator with a 5-amp rating. It's engineered for use with lead-acid batteries in automotive, marine, and deep-cycle applications, covering flooded, gel, AGM, maintenance-free variants, and even lithium-ion batteries.


Features:

  • Do more with Genius - Designed for 6-volt and 12-volt lead-acid automotive, marine, and deep-cycle batteries, including flooded, gel, AGM, and maintenance-free, plus lithium-ion batteries.
  • Enjoy precision charging - An integrated thermal sensor detects the ambient temperature and alters the charge to eliminate over-charging in hot climates and under-charging in cold climates.
  • Charge dead batteries - Charges dead batteries as low as 1-volt. Or use the all-new Force Mode that allows you to take control and manually begin charging dead batteries down to zero volts.
  • Simple to set up and use - Plug-in, connect to the battery, select a charge mode, and start charging your battery. A fully-automatic, worry-free battery charger for year-round use.
  • Restore your battery - Detects sulfation and acid stratification and restores lost performance for stronger engine starts and extended battery life.
  • Compatible with all types of vehicles - Charge and maintain cars, motorcycles, lawnmowers, ATVs, tractors, trucks, SUVs, boats, classic cars, hot rods, and more - you name it.


WARNING: This product contains chemicals known to the state of California to cause cancer, birth defects, and/or reproductive harm. See above warning label as well as http://www.p65warnings.ca.gov for further information on Proposition 65 warnings.

Show More Show Less
NOCO - Corporate Logo
T#:2498430
Part#: GBX75
Ships in 8 Business Days
22% off MSRP $ 319.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 249.99 USD
Free Shipping
22% off MSRP
$ 319.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 249.99 USD
Free Shipping

The NOCO Boost X GBX75 is a portable lithium jump starter crafted for 12-volt batteries in vehicles with gasoline engines up to 8.5 liters and diesel engines up to 6.5 liters. This versatile tool is suitable for a wide array of vehicles, including cars, motorcycles, trucks, ATVs, boats, RVs, vans, SUVs, tractors, and more. Featuring an all-new design, the GBX75 offers extreme jump-starting power, ensuring robust engine starts with ease. With a rating of 2500 amps, this portable lithium car battery jump starter delivers maximum energy with each start. It's not just an upgrade; it's part of our new Extreme Series, delivering exceptional performance and reliability.


Features:

  • Equipped with USB-C technology that, combined with power delivery, gives you lightning-fast recharges. Completely recharges in just 1.8-hours, or go from 0% to jump starting in just 5-minutes of charge.
  • Charge everything with USB-C Power Delivery. Its internal power bank provides 60-watts of power - both in and out - to effortlessly power your favorite USB-C devices, like phones, tablets, laptops, wearables, and more.
  • We took our UltraSafe technology and made it better. It's still our simple, mistake-free design featuring spark-proof technology and reverse polarity protection, but with enhanced thermal efficiency and power management to provide better performance and longer battery life.
  • It's one of the most versatile lithium jump starters ever. Jump start all vehicle types, including cars, motorcycles, trucks, ATVs, boats, RVs, vans, SUVs, tractors, and more for up to 8.5-liter gasoline and 6.5-liter diesel engines.


WARNING: This product contains chemicals known to the state of California to cause cancer, birth defects, and/or reproductive harm. See above warning label as well as http://www.p65warnings.ca.gov for further information on Proposition 65 warnings.

Show More Show Less
NOCO - Corporate Logo
T#:641115
Part#: GBC003
In Stock
Sale - Save 6% $ 24.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 23.61 USD
Free Shipping on orders $49 and up
Sale - Save 6%
$ 24.99

This product was last offered at the strikethrough price on
05-03-2026

$ 23.61 USD
Free Shipping on orders $49 and up

The NOCO GBC003 Boost HD Precision Battery Clamps are heavy-duty clamps crafted for use with 12-volt gas and diesel engines. These clamps feature a needle-nose profile, allowing them to fit any shape or size battery terminal, from small terminals in tight spaces to top and side post batteries, as well as large terminal sizes. Their robust and rugged springs ensure maximum current flow with minimal power loss. Additionally, the Boost HD Precision accessory boasts no-melt and smoke-free properties, high current transferability, and reinforced all-metal construction.


Features: 

  • Heavy-duty battery clamp designed for both 12-volt gas and diesel engines.
  • Needle-nose clamp profile for jump starting hard-to-reach and oversized battery terminals.
  • Made from durable, heat stabilized 8 AWG silicone wire that maintains its flexibility in cold weather environments.
  • Engineered to efficiently transfer maximum current flow with minimal power loss.
  • Compatible with the GB20, GB40, GB50, and GBX45 UltraSafe Lithium Jump Starters.


WARNING: This product contains chemicals known to the state of California to cause cancer, birth defects, and/or reproductive harm. See above warning label as well as http://www.p65warnings.ca.gov for further information on Proposition 65 warnings.

Show More Show Less


NOCO - Corporate Logo
T#:641108
Part#: GB40
In Stock
20% off MSRP $ 124.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 99.99 USD
Free Shipping
20% off MSRP
$ 124.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 99.99 USD
Free Shipping

The GB40 is a compact lithium-ion battery jump starter pack capable of delivering 1,000 amps, allowing you to jump-start a dead battery within seconds. Equipped with patented safety technology, it ensures spark-proof connections and reverse polarity protection, making it user-friendly and safe for everyone. Not only does it serve as a powerful battery booster, but it also functions as a portable power source for charging USB devices such as smartphones and tablets. Designed to support vehicles like cars, boats, RVs, trucks, and more, it can handle gas engines up to 6 liters and diesel engines up to 3 liters.



Features:

  • Compact, yet powerful lithium jump starter rated at 1,000 Amps - up to 20 jump starts on a single charge.
  • An ultra-safe and mistake-proof design with spark-proof technology and reverse polarity protection, which allow it to safely connect to any battery.
  • An ultra-bright 100 lumen LED flashlight with 7 light modes, including SOS and emergency strobe.
  • Recharge your personal devices on the go, like smartphones, tablets, e-watches and more - up to 4 smartphone recharges.
  • Designed for gas engines up to 6 Liters and diesel engines up to 3 Liters for cars, boats, lawn mowers and more.


WARNING: This product contains chemicals known to the state of California to cause cancer, birth defects, and/or reproductive harm. See above warning label as well as http://www.p65warnings.ca.gov for further information on Proposition 65 warnings.

Show More Show Less
Mishimoto - Corporate Logo
T#:23020165
Part#: MMBCC-CBTWO
In Stock
$ 160.99 USD
Free Shipping on orders $49 and up

Optimize your vehicle's performance and shield crucial components with the Mishimoto Compact 2-Port Baffled Oil Catch Can. This innovative solution effectively separates oil particles from PCV/CCV air using a 50-micron bronze filter, ensuring defense against oil blow-by for your intercooler, intake system, and vital parts. Constructed with a patented billet 6061 aluminum can sealed with Viton™ O-Rings, this catch can guarantees both durability and effectiveness.

Equipped with a universal mounting bracket, it allows adaptable installation and comes complete with two CNC-machined aluminum 1/2" barbed hose fittings. With an enhanced 3 oz internal capacity, service intervals are prolonged, while its fully serviceable filter and can ensure enduring functionality.

Engineered for safety in pressurized applications, the internal air diverter enhances oil separation by amplifying air turbulence. Available in black, red, or polished finishes, this catch can preserves proper octane levels, reducing potential detonation and promoting extended engine life.

The product package includes the Compact 2-Port Baffled Oil Catch Can, two Aluminum 1/2" Barbed Fittings, and a Universal Mounting Bracket, all backed by the Mishimoto Lifetime Warranty.

WARNING! Prop 65 may apply to this product.

Proposition 65 (Safe Drinking Water and Toxic Enforcement Act of 1968) is a California law that applies to all companies selling products in California.

Prop 65 mandates listing any chemical present above very low levels that are known to cause cancer, birth defects, or other reproductive harm.

For more information about California Prop 65 warning, visit: www.P65Warnings.ca.gov.

Show More Show Less
Mishimoto - Corporate Logo
T#:383384
Part#: MMBCCN5406CBE
In Stock
$ 253.99 USD
Free Shipping
$ 253.99 USD
Free Shipping
Oil venting and circulation continues to be a problem on BMW engines and now even more so on the turbocharged N54 and N55 engines. The existing stock system does a very poor job of separating fluid and vapor and this leads to an oily film or even small pools of oil throughout the turbos and intake. We're seeing a lot more 135 and 335 cars with drivability and performance issues because oil has sneaked by the ring seals and is coating the intake piping, intercooler, intake valves, and other critical areas. The problem is worsened with higher boost levels. Oil is excellent for lubricating moving parts but terrible when it gets into the combustion chamber, effectively lowering the octane rating and reducing performance. Our own shop has gone the extra step and offers media and chemical blasting of the intake valves to strip away the oily buildup we have seen. Our shop also strongly recommends an oil catch can be installed in the line for the crankcase vent. The oil catch can traps oil as it leaves the valve cover and holds it in a canister. This catch can is located on the cooler side of the engine where the oil will condense easier and stay in the can. Whatever minimal vapors are left over in the oil is then vented back through the canister and into the intake where it is safe to be burned up in the engine or recirculated back through the system again. This is the way the system was designed! At each oil change simply unscrew the canister and empty the trapped oil with your regular used oil. Installing one of these will avoid costly repairs in the future and help maintain your boost and performance. It's one of the smartest modifications you can make because it demonstrates a well-thought out tuning strategy and care for the condition of your engine. The Mishimoto Oil Catch Can is made from aluminum and with a stealthy black anodized finish. It installs on the cooler side of the engine with a dedicated bracket and new oversized vent lines. The location is key as heat will evaporate the oil and send too much vapor back into the engine (where cooler air will turn it back into fluid). Note: Since the crankcase vent system is considered part of the overall emissions system, installing this may be a violation of local, state, and federal laws. While exemptions are made for track/race and off-road use, check with your local state inspection facility on using this in street-driven vehicles. This item fits the following BMWs with the N54 twin-turbo engine: 2008-2010 E82 E88 BMW 135i 2007-2010 E9X BMW 335i 335xi 2006-2010 E60 BMW 535i 535xi WARNING! Prop 65 may apply to this product. Proposition 65 (Safe Drinking Water and Toxic Enforcement Act of 1968) is a California law that applies to call companies selling products in California. Prop 65 requires any listed chemical present above very low levels that are known to cause cancer, birth defects, or other reproductive harm. For more information about California Prop 65 warning see: www.P65Warnings.ca.gov.
Show More Show Less

Beru - Corporate Logo
T#:23383348
Part#: 12137510738
Ships in 3 Business Days
$ 92.99 USD
Free Shipping on orders $49 and up
Is your Mini experiencing sluggish acceleration or misfires? It might be time to check the coil pack. The coil pack plays a crucial role in the ignition system and can affect engine performance. Replace it as necessary or ideally every 100,000 miles to keep your Mini's ignition system operating smoothly.
Show More Show Less

Mishimoto - Corporate Logo
T#:378421
Part#: MMOCU
In Stock at Vendor
$ 410.99 USD
Free Shipping
$ 410.99 USD
Free Shipping
This universal oil cooler from Mishimoto is far superior to the factory unit with its 11" x 2.76" x 1.97" core. Even under optimum driving conditions increased oil temperatures will cause a drop in pressure and will decrease the ability for your engine to be properly lubricated. With this new oil cooler, you can keep your oil temperatures down for optimum driving conditions. The kit includes 4 feet of stainless braided line, adapter fittings, and oil filter sandwich adapter. Mishimoto Automotive is a leading manufacturer of aftermarket performance cooling products. The company was established back in 2003 with one goal. That goal was to provide customers with quality cooling system upgrades that work on the track and on the road. At Mishimoto, you never have to worry about the quality of the product you are installing. This kit is universal and is not a direct bolt on. *For custom applications only. Not a direct bolt on. WARNING! Prop 65 may apply to this product. Proposition 65 (Safe Drinking Water and Toxic Enforcement Act of 1968) is a California law that applies to call companies selling products in California. Prop 65 requires any listed chemical present above very low levels that are known to cause cancer, birth defects, or other reproductive harm. For more information about California Prop 65 warning see: www.P65Warnings.ca.gov.
Show More Show Less
Mishimoto - Corporate Logo
T#:31092530
Part#: MMODP1615B
Ships in 3 Business Days
$ 22.99 USD
Free Shipping on orders $49 and up

MINI R55 to R61 Magnetic Engine Oil Drain Plug M16X1.5 removes abrasive metal particles from drivetrain fluid to ensure longevity. The magnet attracts and holds minute abrasive and ferrous metal particles, preventing their circulation through lubrication systems. Metal particles can appear in lubricating or hydraulic systems due to normal wear, machining residues, sub-surface casting flaws, and stress usage. Mishimoto Drain Plugs help prevent excessive wear to internal components by holding these particles.

  • Enhanced Engine Protection: Removes metal particles to reduce wear
  • Magnetic Attraction: Holds abrasive and ferrous particles securely
  • Improved Lubrication: Prevents circulation of harmful particles
  • Durable Construction: Built to last and withstand harsh conditions
  • Easy Installation: Simple to replace with standard drain plug

Safety Note: This product may be subject to Proposition 65, a California law requiring warnings for products containing chemicals known to cause cancer, birth defects, or other reproductive harm. For more information, visit www.P65Warnings.ca.gov.

Show More Show Less

NOCO - Corporate Logo
T#:641137
Part#: GENIUS10
Ships in 8 Business Days
20% off MSRP $ 124.95

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 99.94 USD
Free Shipping
20% off MSRP
$ 124.95

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 99.94 USD
Free Shipping

The GENIUS10 is a powerhouse among our chargers known for its exceptional performance, energy efficiency, and compact design. The GENIUS10 is a versatile 6-volt and 12-volt charger, maintainer, and desulfator with a robust 10-amp rating. It's engineered to handle lead-acid batteries used in automotive, marine, and deep-cycle applications, covering flooded, gel, AGM, maintenance-free types, as well as lithium-ion batteries.


Features:

  • Do more with Genius - Designed for 6-volt and 12-volt lead-acid automotive, marine, and deep-cycle batteries, including flooded, gel, AGM, and maintenance-free, plus lithium-ion batteries.
  • Enjoy precision charging - An integrated thermal sensor detects the ambient temperature and alters the charge to eliminate over-charging in hot climates and under-charging in cold climates.
  • Charge dead batteries - Charges dead batteries as low as 1-volt. Or use the all-new Force Mode that allows you to take control and manually begin charging dead batteries down to zero volts.
  • Simple to set up and use - Plug-in, connect to the battery, select a charge mode, and start charging your battery. A fully-automatic, worry-free battery charger for year-round use.
  • Restore your battery - Detects sulfation and acid stratification and restores lost performance for stronger engine starts and extended battery life.
  • Compatible with all types of vehicles - Charge and maintain cars, motorcycles, lawnmowers, ATVs, tractors, trucks, SUVs, boats, classic cars, hot rods, and more - you name it.


WARNING: This product contains chemicals known to the state of California to cause cancer, birth defects, and/or reproductive harm. See above warning label as well as http://www.p65warnings.ca.gov for further information on Proposition 65 warnings.

Show More Show Less
NOCO - Corporate Logo
T#:1135807
Part#: GENIUS1
In Stock
25% off MSRP $ 39.95

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 29.94 USD
Free Shipping on orders $49 and up
25% off MSRP
$ 39.95

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 29.94 USD
Free Shipping on orders $49 and up

The cutting-edge GENIUS1 is a powerhouse among our chargers renowned for its exceptional performance, energy efficiency, and compact design. The GENIUS1 is a versatile 6-volt and 12-volt charger, maintainer, and desulfator with a 1-amp rating. It's engineered to work with lead-acid batteries in automotive, marine, and deep-cycle applications, supporting flooded, gel, AGM, maintenance-free types, and even lithium-ion batteries.


Features: 

  • Do more with Genius - Designed for 6-volt and 12-volt lead-acid automotive, marine, and deep-cycle batteries, including flooded, gel, AGM, and maintenance-free, plus lithium-ion batteries.
  • Enjoy precision charging - An integrated thermal sensor detects the ambient temperature and alters the charge to eliminate over-charging in hot climates and under-charging in cold climates.
  • Charge dead batteries - Charges dead batteries as low as 1-volt. Or use the all-new Force Mode that allows you to take control and manually begin charging dead batteries down to zero volts.
  • Simple to set up and use - Plug-in, connect to the battery, select a charge mode, and start charging your battery. A fully-automatic, worry-free battery charger for year-round use.
  • Restore your battery - Detects sulfation and acid stratification and restores lost performance for stronger engine starts and extended battery life.
  • Compatible with all types of vehicles - Charge and maintain cars, motorcycles, lawnmowers, ATVs, tractors, trucks, SUVs, boats, classic cars, hot rods, and more - you name it.


WARNING: This product contains chemicals known to the state of California to cause cancer, birth defects, and/or reproductive harm. See above warning label as well as http://www.p65warnings.ca.gov for further information on Proposition 65 warnings.

Show More Show Less

Black Forest Industries - Corporate Logo
T#:18401885
Part#: EBFI77-KA90-661
In Stock
$ 639.99 USD
Free Shipping on orders $49 and up
After being thoroughly designed and tested, BFI has released their A90/Z4 line of billet engine mounts. While maintaining comfort and reliability, these engine mounts allow your engine to perform under increased power thanks to their billet and urethane construction. Features: Creates a sturdier and longer-lasting connection to the engine. Laser-scanned to ensure perfect fitment. Billet aluminum construction
Show More Show Less

NOCO - Corporate Logo
T#:641139
Part#: GENIUS2
In Stock
23% off MSRP $ 64.95

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 49.94 USD
Free Shipping on orders $49 and up
23% off MSRP
$ 64.95

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 49.94 USD
Free Shipping on orders $49 and up

The GENIUS2 is NOCO's most potent charger yet. This energy-efficient and compact device is designed to handle both 6-volt and 12-volt batteries, functioning as a charger, maintainer, and desulfator all in one. With a 2-amp rating, it's suitable for various lead-acid batteries used in automotive, marine, and deep-cycle applications, including flooded, gel, AGM, maintenance-free types, as well as lithium-ion batteries.


Features:

  • Meet the GENIUS2 - Similar to the G1100, just better. It's 30% smaller and delivers 140% more power. And it's simpler and easier to use than ever before.
  • Do more with Genius - Designed for 6-volt and 12-volt lead-acid automotive, marine, and deep-cycle batteries, including flooded, gel, AGM, and maintenance-free, plus lithium-ion batteries.
  • Enjoy precision charging - An integrated thermal sensor detects the ambient temperature and alters the charge to eliminate over-charging in hot climates and under-charging in cold climates.
  • Charge dead batteries - Charges dead batteries as low as 1-volt. Or use the all-new Force Mode that allows you to take control and manually begin charging dead batteries down to zero volts.
  • Simple to set up and use - Plug-in, connect to the battery, select a charge mode, and start charging your battery. A fully-automatic, worry-free battery charger for year-round use.
  • Restore your battery - Detects sulfation and acid stratification and restores lost performance for stronger engine starts and extended battery life.
  • Compatible with all types of vehicles - Charge and maintain cars, motorcycles, lawnmowers, ATVs, tractors, trucks, SUVs, boats, classic cars, hot rods, and more - you name it.


WARNING: This product contains chemicals known to the state of California to cause cancer, birth defects, and/or reproductive harm. See above warning label as well as http://www.p65warnings.ca.gov for further information on Proposition 65 warnings.

Show More Show Less
Autel - Corporate Logo
T#:2914116
Part#: AL329
Ships in 1 Business Day
$ 49.99 USD
Free Shipping on orders $49 and up
OBDII Code Reader


Black Forest Industries - Corporate Logo
T#:29068517
Part#: EBFI77-MG20-601
Ships on Sep 8, 2026
$ 634.99 USD
Free Shipping on orders $49 and up

From the factory, all BMWs utilize soft rubber or fluid-filled engine mounts. Not only are these mounts prone to degradation, they also allow ample movement of the drivetrain. This translates to looseness in your driveline, commonly associated with missed shifts and a generally isolated feeling.

To improve upon this issue, Black Forest Industries designed these upgraded mounts from the ground up. Their stage one mounts feature a proprietary 65A durometer bushing and bracket/cup design. Maximizing bushing area while minimizing vibration gives this mount the advantage of having the best ride characteristics possible from a urethane mount.

Features:

Perfect fit: Utilizing laser-scanning technology permits seamless integration with the factory engine mount arms. Quality tooling: All bosses are matched replicas with stock locations, and all tool clearances and specs are maintained. Heavy-duty construction: The use of billet aluminum instead of cast creates a mount that is dramatically stronger than its factory cast-construction counterpart. Performance design: 65A durometer bushings are geared toward the spirited driving enthusiast who wants better control over motor movement without sacrificing excessive vibrations. Choose BFI Stage 1 for a quality mount that eliminates drivetrain movement without adding excessive NVH.

Show More Show Less
Mishimoto - Corporate Logo
T#:599444
Part#: MMBCC-N55-11CBE
Back Ordered
9% off MSRP $ 300.00

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 272.99 USD
Free Shipping
9% off MSRP
$ 300.00

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 272.99 USD
Free Shipping
BMW 335I/335XI/135I Direct Fit Catch Can, 2011-2013 Direct fit for 2011-2013 BMW 335I/335XI/135I Single 2-Port Compact Baffled Oil Catch Can separates oil particles using 50-micron bronze filter Application-specific bracket mounts the can in a serviceable location Billet 6061 aluminum sealed can Defends intercooler, intake system, and VANOS system from oil blow-by Helps maintain proper octane levels to reduce potential detonation Internal air diverter increases air turbulence to improve oil separation Filters and can are fully serviceable Mishimoto Lifetime Warranty The Mishimoto BMW N55 Baffled Oil Catch Can is designed and engineered to reduce carbon build-up, a common issue with the direct fuel injection N55 engines. The Mishimoto BMW N55 catch can kit uses proven engineering from the Mishimoto 2-Port Compact Baffled Oil Catch Can, with its bronze filter and internal baffle, to better separate the oil from the crankcase vapors. WARNING! Prop 65 may apply to this product. Proposition 65 (Safe Drinking Water and Toxic Enforcement Act of 1968) is a California law that applies to call companies selling products in California. Prop 65 requires any listed chemical present above very low levels that are known to cause cancer, birth defects, or other reproductive harm. For more information about California Prop 65 warning see: www.P65Warnings.ca.gov.
Show More Show Less
Mishimoto - Corporate Logo
T#:637354
Part#: MMB-F80-PP
EO#: D-759-13
Ships in 3 Business Days
$ 2,652.99

This product was last offered at the strikethrough price on
08-13-2026

$ 2,521.99 USD
$ 2,521.99 USD
BMW has a knack for maintaining its stake as the benchmark when it comes to performance luxury vehicles, with the F8X generation being no exception. The S55 that powers the 2015–2020 BMW F8X M3, M4, and M2 Competition is dripping with technology, which includes an air-to-water intercooling system as a means of keeping cool. Where BMW’s intercooling system design was enough to help bring this generation of mid-sized M’s to their peak, we here at Mishimoto found some weaknesses that we felt obliged to address, with a power bundle consisting of our full Performance Intercooler Product suite. The Mishimoto 2015–2020 BMW F8X M3/M4 Performance Intercooler Power Pack counters the weaknesses in BMW’s design, starting with the charge pipes. Cracking under pressure or splitting at the seams are common problems with factory plastic charge pipes. These can result in less than ideal situations as you pilot your M3 or M4. We created a brand-new design for the charge pipes that inspire more confidence in handling the boost pressure. Our design features a full aluminum construction with a cast midsection designed specifically to squeeze past the intake. Our charge pipe kit also includes a pair of matte black silicone couplers for a sleek and secure connection to the intercooler. The nondescript silver box is out, and the stylish new Mishimoto Performance Air-to-Water Intercooler is in. With a new look, our design fits perfectly in the M3 and M4’s engine bay, both in terms of installation and aesthetics. The beauty is more than just skin deep. Our improved core design features a bar-and-plate core with a 29% increase in core volume, as well as a unique single-pass coolant flow layout for optimal heat transfer. Combined with our 16% increase in flow through the core, we were able to record a 12°F temperature drop in intake air temperatures while testing our full Power Pack. An air-to-water intercooling system wouldn’t be complete without the heat exchanger. When it came to BMW’s design, it was a solid foundation, but we still saw room to grow, literally. Our full aluminum design added 6” to the height of the core, equating in a 180% increase in external fin surface area and a 60% increase in core volume. With our heat exchanger in the S55’s system, we recorded a 10°F drop in global intercooler coolant temperatures and an average gain of 11 whp and 8 wtq when the full Mishimoto 2015–2020 BMW F8X Performance Intercooler Power Pack was tested on our Stage 1 tuned M3. For added security, we made sure to include our optional steel mesh stone guard with the Mishimoto Performance Heat exchanger to keep all the tubes and fins intact. We also utilized a variable fin pitch on our heat exchanger’s core for optimal cooling on DCT-equipped vehicles. Even though the F8X generation of the M3, M4, and M2 Competition was designed to pull ahead of the rest, there's still much to be desired when it comes to cooling. The Mishimoto 2015–2020 BMW F8X M3/M4 Performance Intercooler Power Pack is the perfect companion for your build, and like all of our products, is covered under the Mishimoto Lifetime Warranty. Features: ​Direct fit for the BMW F8X M3, M4, and M2 Competition Includes S55 Performance Intercooler, Heat Exchanger, and Charge Pipe Kit 12°F drop in intake air temperatures and 10°F reduction in global intercooler coolant temperatures Dyno-proven average power gains of 11 whp and 8 wtq with peak gains of up to 31 whp and 10 wtq on stage 1 tuned vehicle The intercooler features a unique bar-and-plate, single-pass coolant passage design, and cast aluminum end tanks for optimal flow and cooling capacity Intercooler core volume increased by 29% with 16% improved flow Heat Exchanger features all-aluminum construction with 180% increase in fin surface area and 60% increase in core volume Heat exchanger includes an optional stone guard for added protection against road debris Heat Exchanger utilizes variable fin pitch for improved flow to DCT cooler Charge Pipe Kit features full aluminum construction and cast midsection for maximum durability and perfect fitment Charge pipes include matte silicone couplers for sleek and secure connection to the intercooler Mishimoto Lifetime Warranty Includes: (1) Performance Air-to-Water Intercooler (1) Performance Heat Exchanger (1) Heat Exchanger Stone Guard (2) Charge Pipes (2) Silicone Couplers (4) Worm Gear Clamps Mounting Hardware Mishimoto Lifetime Warranty WARNING! Prop 65 may apply to this product. Proposition 65 (Safe Drinking Water and Toxic Enforcement Act of 1968) is a California law that applies to call companies selling products in California. Prop 65 requires any listed chemical present above very low levels that are known to cause cancer, birth defects, or other reproductive harm. For more information about California Prop 65 warning see: www.P65Warnings.ca.gov.
Show More Show Less

Mishimoto - Corporate Logo
T#:389788
Part#: MMBCCN20N2612CB
In Stock at Vendor
$ 278.95 USD
Free Shipping
$ 278.95 USD
Free Shipping
il venting and circulation continues to be a problem on BMW engines and the N20 engine is not immune from this. The existing stock system does a poor job of separating fluid and vapor and this leads to an oily film or even small pools of oil throughout the turbos and intake. Performance issues are caused by oil sneaking by the ring seals and is coating the intake piping, intercooler, intake valves, and other critical areas. The problem is worsened with higher boost levels. Oil is excellent for lubricating moving parts but terrible when it gets into the combustion chamber, effectively lowering the octane rating and reducing performance. Our own shop has gone the extra step and offers media and chemical blasting of the intake valves to strip away the oily buildup we have seen. Our shop also strongly recommends an oil catch can be installed in the line for the crankcase vent. The oil catch can traps oil as it leaves the valve cover and holds it in a canister. This catch can is located on the cooler side of the engine where the oil will condense easier and stay in the can. Whatever minimal vapors are left over in the oil is then vented back through the canister and into the intake where it is safe to be burned up in the engine or recirculated back through the system again. This is the way the system was designed! At each oil change simply unscrew the canister and empty the trapped oil with your regular used oil. Installing one of these will avoid costly repairs in the future and help maintain your boost and performance. It's one of the smartest modifications you can make because it demonstrates a well-thought out tuning strategy and care for the condition of your engine. The Mishimoto Oil Catch Can is made from aluminum and with a stealthy black anodized finish. It installs on the cooler side of the engine with a dedicated bracket and new oversized vent lines. The location is key as heat will evaporate the oil and send too much vapor back into the engine (where cooler air will turn it back into fluid). Note: Since the crankcase vent system is considered part of the overall emissions system, installing this may be a violation of local, state, and federal laws. While exemptions are made for track/race and off-road use, check with your local state inspection facility on using this in street-driven vehicles. This item fits the following BMWs with the N20 or N26 turbo engine: 2014-2016 F2X 228i 228i xDrive 2012-2016 F3X 320i 320i xDrive 328i 328i xDrive 428i 428i xDrive WARNING! Prop 65 may apply to this product. Proposition 65 (Safe Drinking Water and Toxic Enforcement Act of 1968) is a California law that applies to call companies selling products in California. Prop 65 requires any listed chemical present above very low levels that are known to cause cancer, birth defects, or other reproductive harm. For more information about California Prop 65 warning see: www.P65Warnings.ca.gov.
Show More Show Less

Mishimoto - Corporate Logo
T#:5282875
Part#: MMOC-E60-06
In Stock at Vendor
$ 714.99 USD
Free Shipping
$ 714.99 USD
Free Shipping
After over a decade of use, some of the E60 M5 & E63/64 M6 components have begun to show their age. The factory engine oil cooler is a common leak point on the E60, typically from failed O-rings or cracked weld points. In addition, the location of the front-mounted cooler increases the chance of damage from road debris and general clogging of external fins, resulting in reduced cooling efficiency. That, combined with the high-strung engine and hefty chassis, means oil temperatures tend to rise during aggressive driving. That's why Mishimoto's engineering team set out to remedy both issues with this performance oil cooler. Drawing on their vast experience with BMWs and the latest in engineering tools, Mishimoto's team was able to create a direct-fit replacement oil cooler with substantial improvements in both durability and cooling efficiency. The Mishimoto Performance Oil Cooler features a robust bar-and-plate core, which provides improved durability and aids in heat rejection. The core utilizes a strategic fin design which provides a 41% increase in external fin surface area and a 30% increase in internal fin surface area to help draw heat out of the oil and dissipate it into the air. This oil cooler features CNC-machined inlet/outlet ports and includes new OEM O-rings for a seamless and leak-free installation. This cooler is finished in a silver powder coat, ensuring long-term durability and corrosion resistance. And, as with all BMW performance products, this oil cooler includes the signature Mishimoto Lifetime Warranty. Fits 2006-2010 BMW E60 M5 / E63 M6 / E64 M6* (*Requires minor trimming of plastic OEM oil cooler shrouding) Replaces failure-prone factory oil cooler and provides improved cooling performance 40.3% increase in core volume for efficient cooling Robust bar-and-plate core provides improved pressure tolerance and durability 41% increase in external fin surface area for improved heat transfer 30% increase in internal fin surface area draws heat out of oil quickly and efficiently CNC-machined inlet/outlet mates perfectly with stock oil cooler lines Includes OEM oil line O-rings Durable silver powder coated finish provides optimal corrosion resistance Patent Pending Mishimoto Lifetime Warranty Included: Mishimoto Performance Oil Cooler Oil Line O-rings Mishimoto Lifetime Warranty​ WARNING! Prop 65 may apply to this product. Proposition 65 (Safe Drinking Water and Toxic Enforcement Act of 1968) is a California law that applies to call companies selling products in California. Prop 65 requires any listed chemical present above very low levels that are known to cause cancer, birth defects, or other reproductive harm. For more information about California Prop 65 warning see: www.P65Warnings.ca.gov.
Show More Show Less
Vaico - Corporate Logo
T#:34114245
Part#: V20-3674
In Stock
$ 827.99

This product was last offered at the strikethrough price on
05-07-2026

$ 497.99 USD
Free Shipping on orders $49 and up
$ 497.99 USD
Free Shipping on orders $49 and up

If your N52 engine is running rough, is low on power, or you are getting check engine lights for timing related issues, there is a good chance that you have a faulty VANOS component. The two most common parts to fail are the Camshaft Adjusters and VANOS Solenoids.

This repair kit from Vaico includes all of the basic parts necessary to service the VANOS system and restore smooth engine operation.

Included:

Intake Camshaft Adjuster w/ Impulse Wheel

Exhaust Camshaft Adjuster w/ Impulse Wheel

Camshaft Adjuster Bolts

VANOS Solenoid Valves

Valve Cover Gasket Set

Show More Show Less

Mishimoto - Corporate Logo
T#:15544955
Part#: MMOC-G80-21SL
In Stock at Vendor
$ 776.99 USD
Free Shipping on orders $49 and up
Keep your 2021+ BMW M3/M4 cool and collected with the Mishimoto 2021+ BMW M3/M4 performance oil cooler. Much like their predecessors, the G8X M3 and M4 were designed with efficiency in mind. This can be a double-edged sword, as the optimally arranged engine bay has components placed in precarious positions. Most notably, the oil cooler is placed on the undercarriage, parallel to the road's surface. This placement increases air flow and uses aerodynamics to pull air through the core, but it also makes the stock cooler vulnerable to scrapes, bumps, and other road hazards. With this in mind, the engineers at Mishimoto set out to design a robust G8X oil cooler to keep your M3 or M4 running cool on and off the track. We started by swapping the stock tube-and-fin cooler for a bar-and-plate with CNC-machined end tanks. Our cooler boasts a 35.7-percent thicker core and a 41-percent increase in core volume for superior cooling efficiency. Our cooler fits directly in place of the stock unit and retains the stock seals and bash guards for optimal airflow and additional protection. The Mishimoto performance oil cooler for the 2021+ BMW G8X M3/M4 includes everything needed for installation and, as with all Mishimoto products, it's protected by the Mishimoto Lifetime Warranty for a lifetime of protection and cooling. Product Features: Direct fit for the 2021+ BMW G8X M3/M4 Full aluminum TIG-welded construction 41-percent increase in core volume and 35.7-percent thicker core than stock for improved cooling efficiency Robust bar-and-plate core provides superior pressure tolerance and durability Retains stock seals for optimal air flow from fresh air ducts Retains bash guards to protect cooler from bumps and curbs Silver powder coated finish for maximum corrosion resistance No cutting or modifications required Includes everything needed for installation Mishimoto Lifetime Warranty
Show More Show Less
Mishimoto - Corporate Logo
T#:2839826
Part#: MMSBH-F80-15
In Stock at Vendor
$ 456.99 USD
Free Shipping on orders $49 and up
The F8X M3/4 are equipped with a set of hardlines connecting the oil pump tot he oil cooler, these corrode overtime and start to fail causing oil leaks leading and improper oiling of your engine. This Mishimoto kit includes both lines and all needed brackets and hardware for a OE like installation, Features Direct replacement for OE hard lines -10AN fittings and adapters for use with OE oil cooler Mishimoto Lifetime Warranty WARNING! Prop 65 may apply to this product. Proposition 65 (Safe Drinking Water and Toxic Enforcement Act of 1968) is a California law that applies to call companies selling products in California. Prop 65 requires any listed chemical present above very low levels that are known to cause cancer, birth defects, or other reproductive harm. For more information about California Prop 65 warning see: www.P65Warnings.ca.gov.
Show More Show Less

Mishimoto - Corporate Logo
T#:6258386
Part#: MMOC-F10-12SL
In Stock at Vendor
$ 887.99 USD
Free Shipping
$ 887.99 USD
Free Shipping
The BMW M5 power and handling statistics are completely mind-blowing for a car tipping the scales at well over two tons. The S63 twin-turbo V8 is underrated from the factory and responds well to tuning and bolt on modifications. Calling it the ultimate super sedan would not do this car justice, it’s just that good. But every amazing automobile must have an Achilles’ heel, right? Some investigation into this model told us that enthusiasts were seeing elevated oil temperatures during track driving conditions. Our team set out to create a replacement, high-performance oil cooler that could handle the rigors of extreme driving conditions and the abuse of daily commuting. The Mishimoto S63 M5/M6 oil cooler features extremely precise CNC-machined billet-aluminum end tanks which are professionally TIG-welded to our robust bar-and-plate core. Our strategically designed 55mm-thick core provides a massive 24% increase in core volume, and a 40% increase in external fin surface area. This added surface area promotes greater heat transfer, which directly impacts internal fluid temperatures. Our performance oil cooler is a complete bolt-on solution that includes everything needed for an easy installation such as hardware and replacement O-rings for the oil lines. Our heat exchanger is finished in a durable silver powder coat, providing both corrosion resistance and improved aesthetics. Whether your M5 sees frequent track time or just the occasional back-road jaunt, upgrading the oil cooler is a great way to extend the life of your S63 and ensure maximum engine output when you need it most. As with all our BMW products, this oil cooler includes our signature Mishimoto Lifetime Warranty. Direct fit for 2012+ BMW M5/M6 models CNC-machined billet aluminum end tanks provide improved durability over stock stamped tanks Robust bar-and-plate core resists damage from road debris and provides optimal cooling efficiency 24% increase in core volume over stock for improved cooling capacity 40% increase in external fin area provides improved heat transfer during extreme driving conditions Precision CNC-machined inlet and outlet prevent leaks Includes new OEM-quality oil line O-rings for easy installation Durable silver powder coated finish prevents corrosion Mishimoto Lifetime Warranty Purchase Includes: (1) Performance Oil Cooler (4) Mounting Bracket Grommets (2) Oil Line Connection M8 X 1.25 Bolts (2) Oil Line O-rings Mishimoto Lifetime Warranty WARNING! Prop 65 may apply to this product. Proposition 65 (Safe Drinking Water and Toxic Enforcement Act of 1968) is a California law that applies to call companies selling products in California. Prop 65 requires any listed chemical present above very low levels that are known to cause cancer, birth defects, or other reproductive harm. For more information about California Prop 65 warning see: www.P65Warnings.ca.gov. The Mishimoto S63 M5/M6 oil cooler features extremely precise CNC-machined billet-aluminum end tanks which are professionally TIG-welded to our robust bar-and-plate core. Our strategically designed 55mm-thick core provides a massive 24% increase in core volume, and a 40% increase in external fin surface area. This added surface area promotes greater heat transfer, which directly impacts internal fluid temperatures. Our performance oil cooler is a complete bolt-on solution that includes everything needed for an easy installation such as hardware and replacement O-rings for the oil lines. Our heat exchanger is finished in a durable silver powder coat, providing both corrosion resistance and improved aesthetics. Whether your M5 sees frequent track time or just the occasional back-road jaunt, upgrading the oil cooler is a great way to extend the life of your S63 and ensure maximum engine output when you need it most. As with all our BMW products, this oil cooler includes our signature Mishimoto Lifetime Warranty. Direct fit for 2012+ BMW M5/M6 models CNC-machined billet aluminum end tanks provide improved durability over stock stamped tanks Robust bar-and-plate core resists damage from road debris and provides optimal cooling efficiency 24% increase in core volume over stock for improved cooling capacity 40% increase in external fin area provides improved heat transfer during extreme driving conditions Precision CNC-machined inlet and outlet prevent leaks Includes new OEM-quality oil line O-rings for easy installation Durable silver powder coated finish prevents corrosion Mishimoto Lifetime Warranty Purchase Includes: (1) Performance Oil Cooler (4) Mounting Bracket Grommets (2) Oil Line Connection M8 X 1.25 Bolts (2) Oil Line O-rings Mishimoto Lifetime Warranty
Show More Show Less

Black Forest Industries - Corporate Logo
T#:29068521
Part#: EBFI77-MG20-602
Ships on Sep 8, 2026
$ 654.99 USD
Free Shipping on orders $49 and up

From the factory, all BMWs utilize soft rubber or fluid-filled engine mounts. Not only are these mounts prone to degradation, they also allow ample movement of the drivetrain. This translates to looseness in your driveline, commonly associated with missed shifts and a generally isolated feeling.

To improve upon this issue, Black Forest Industries designed these upgraded mounts from the ground up. Their stage one mounts feature a proprietary 85A durometer bushing and bracket/cup design. Maximizing bushing area while minimizing vibration gives this mount the advantage of having the best ride characteristics possible from a urethane mount.

Features:

Perfect fit: Utilizing laser-scanning technology permits seamless integration with the factory engine mount arms. Quality tooling: All bosses are matched replicas with stock locations, and all tool clearances and specs are maintained. Heavy-duty construction: The use of billet aluminum instead of cast creates a mount that is dramatically stronger than its factory cast-construction counterpart. Performance design: 85A durometer bushings are geared toward the spirited driving enthusiast who doesn't mind increasing NVH. Choose BFI Stage 2 for a quality mount that eliminates drivetrain movement.

Note: Stage 2 mounts increase NVH. Therefore, these mounts are not intended to be used on daily driven vehicles.

Show More Show Less
Mishimoto - Corporate Logo
T#:378414
Part#: MMOCUL
In Stock at Vendor
$ 536.99 USD
Free Shipping
$ 536.99 USD
Free Shipping
Even under optimum driving conditions increased oil temperatures will cause a drop in pressure and will decrease the ability for your engine to be properly lubricated. With this new oil cooler, you can keep your oil temperatures down for optimum driving conditions. The kit includes four-feet of stainless braided line, adapter fittings, and oil filter sandwich adapter. Rows: 19 Overall Dimensions: 13" x 5.5" x 2" Core Dimensions: 11.25" x 5.5" x 2" Braided Hoses: 4ft .75 inch & 4ft 9 inch Braided Hose Fittings: -10AN Sandwich Plate Fittings: -10AN WARNING! Prop 65 may apply to this product. Proposition 65 (Safe Drinking Water and Toxic Enforcement Act of 1968) is a California law that applies to call companies selling products in California. Prop 65 requires any listed chemical present above very low levels that are known to cause cancer, birth defects, or other reproductive harm. For more information about California Prop 65 warning see: www.P65Warnings.ca.gov.
Show More Show Less
Mishimoto - Corporate Logo
T#:363342
Part#: MMOCE4601
In Stock at Vendor
$ 1,032.99 USD
$ 1,032.99 USD
The S54 is an incredible feat of engineering. Smooth power delivery, individual throttle bodies, and an 8,000 rpm redline make for an unforgettable driving experience. As with any BMW, maintaining optimal oil temperatures is key to extending the life of your vehicle and ensuring that you're getting an unparalleled driving experience. As many of these vehicles see frequent track time, the team at Mishimoto decided to develop a performance oil cooler kit that would provide improved durability and deliver the power needed for track driving. The result: an extremely efficient core with a proven 30°F (16.7°C) drop in oil temperature. With an increase in core thickness of 110%, this oil cooler kit raises your oil capacity by 0.44 qt. The oil cooler end tanks, cast from a single piece of aluminum and TIG-welded to the core, have been designed for maximum reliability, giving you the confidence you need to push your E46 M3 to the limits.
Show More Show Less


Ferrea - Corporate Logo
T#:28770000
Part#: FER-HPVK-N20-T
Ships in 3 Business Days
$ 619.99 USD
Free Shipping on orders $49 and up
NOCO - Corporate Logo
T#:641109
Part#: GB50
Ships in 8 Business Days
21% off MSRP $ 189.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 149.99 USD
Free Shipping
21% off MSRP
$ 189.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 149.99 USD
Free Shipping

The GB50 is a highly portable, lightweight, and compact lithium-ion jump starter designed for 12-volt batteries. It allows you to safely jump-start a dead battery in seconds, offering up to 30 jump starts on a single charge. Featuring spark-proof technology and reverse polarity protection, the Boost XL is safe and easy for anyone to use.

In addition to its jump-starting capabilities, the GB50 lithium jump starter comes with a high-output 200 lumen LED flashlight with seven light modes. It can hold its charge for up to one year and includes a USB battery pack for recharging personal devices on the go, providing up to 6 smartphone recharges. The Hot and Cold LED indicators on the internal battery help determine when the Boost is outside operating temperatures, safeguarding your batteries and devices.

Rated at 1,500 Amps, the GB50 is suitable for use on gasoline engines up to 7 liters and diesel engines up to 4.5 liters, making it versatile for cars, vans, boats, SUVs, trucks, and more. The package includes the new HD Precision Boost Battery Clamps for easy connection to any 12V lead-acid battery, along with a USB charging cable, microfiber storage bag, a 1-year hassle-free limited warranty, and free lifetime customer support.


Features:

  • Compact, yet powerful lithium jump starter rated at 1,500 amps up to 30 jump starts on a single charge.
  • An ultra-safe and mistake-proof design with spark-proof technology and reverse polarity protection, which allows it to safely connect to any battery.
  • An ultra-bright 200 lumen LED flashlight with 7 light modes including SOS and emergency strobe.
  • Recharge your personal devices on the go, like smartphones, tablets, e-watches and more - up to 6 smartphone recharges.
  • Designed for gas engines up to 7 liters and diesel engines up to 4.5 liters for small diesel cars, SUVs, boats, trucks, ATVs, motorcycles and more.
  • New Feature: Hot and Cold LED indicators of the internal battery operating temperatures to protect your batteries and devices.
  • New Accessory: Includes HD Precision Boost Battery Clamps designed to easily connect to any 12V lead-acid battery from powersports to trucks.


WARNING: This product contains chemicals known to the state of California to cause cancer, birth defects, and/or reproductive harm. See above warning label as well as http://www.p65warnings.ca.gov for further information on Proposition 65 warnings.

Show More Show Less
NOCO - Corporate Logo
T#:2498431
Part#: GBX155
Ships in 8 Business Days
16% off MSRP $ 439.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 369.99 USD
Free Shipping
16% off MSRP
$ 439.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 369.99 USD
Free Shipping

The NOCO Boost X GBX155 is a portable lithium jump starter designed for 12-volt batteries in vehicles with gasoline engines up to 10.0 liters and diesel engines up to 8.0 liters. This versatile device is suitable for cars, motorcycles, trucks, ATVs, boats, RVs, vans, SUVs, tractors, and more. Featuring an all-new design, the GBX155 delivers extreme jump-starting power, ensuring robust engine starts. With a rating of 4250 amps, this portable lithium car battery jump starter provides maximum energy with every start. It's not just an upgrade; it's part of the new Extreme Series, offering unparalleled performance and reliability.


Features:

  • Equipped with USB-C technology that, combined with power delivery, gives you lightning-fast recharges. Completely recharges in just 2.7-hours, or go from 0% to jump starting in just 5-minutes of charge.
  • Charge everything with USB-C Power Delivery. Its internal power bank provides 60-watts of power - both in and out - to effortlessly power your favorite USB-C devices, like phones, tablets, laptops, wearables, and more.
  • We took our UltraSafe technology and made it better. It's still our simple, mistake-free design featuring spark-proof technology and reverse polarity protection, but with enhanced thermal efficiency and power management to provide better performance and longer battery life.
  • It's one of the most versatile lithium jump starters ever. Jump start all vehicle types, including cars, motorcycles, trucks, ATVs, boats, RVs, vans, SUVs, tractors, and more for up to 10.0-liter gasoline and 8.0-liter diesel engines.


WARNING: This product contains chemicals known to the state of California to cause cancer, birth defects, and/or reproductive harm. See above warning label as well as http://www.p65warnings.ca.gov for further information on Proposition 65 warnings.

Show More Show Less

NOCO - Corporate Logo
T#:641121
Part#: GBC010
Ships in 8 Business Days
24% off MSRP $ 32.95

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 24.94 USD
Free Shipping on orders $49 and up
24% off MSRP
$ 32.95

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 24.94 USD
Free Shipping on orders $49 and up

The NOCO GBC010 12V Accessory Kit is designed to connect directly to the XGC IN and OUT ports of NOCO Boost jump starters. This kit allows you to effortlessly power your preferred 12-volt devices directly from a GB70, GB150, GB250+, GB251+, or GB500+, such as a tire inflator, vacuum, coffee maker, fan, cooler, and more. Constructed from high-conductivity 16AWG 100% copper wire, it boasts a rated capacity of 15 amperes.


Features: 

  • Recharge NOCO Boost UltraSafe Lithium Jump Starters from a vehicles 12-volt power source.
  • Compatible with NOCO Boost UltraSafe Lithium Jump Starter models GB70, GB150 GB250+, GB251+ and GB500+.
  • Power 12-volt device like a tire inflator, vacuum and more.
  • High-conductivity 16 AWG copper wire and rated capacity of 15-amperes.
  • Molded strain reliefs prevent unwanted strain on the XGC wire connections.


WARNING: This product contains chemicals known to the state of California to cause cancer, birth defects, and/or reproductive harm. See above warning label as well as http://www.p65warnings.ca.gov for further information on Proposition 65 warnings.

Show More Show Less

NOCO - Corporate Logo
T#:641110
Part#: NOCGB70
Ships in 8 Business Days
20% off MSRP $ 249.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 199.99 USD
Free Shipping
20% off MSRP
$ 249.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 199.99 USD
Free Shipping

The GB70 is a compact and powerful lithium-ion battery jump starter pack capable of delivering 2,000 amps for jump-starting a dead battery within seconds. Equipped with patented safety technology, it ensures spark-proof connections and reverse polarity protection, making it safe and user-friendly for everyone. Not only does it serve as a robust battery booster, but it also functions as a portable power source for recharging USB devices like smartphones, tablets, and more, or for powering 12-volt devices such as tire inflators and power inverters. Designed to support a wide range of vehicles including cars, boats, RVs, trucks, and more, it's compatible with gas engines up to 8 liters and diesel engines up to 6 liters.


Features:

  • Compact, yet powerful lithium jump starter rated at 2,000 amps up to 40 jump starts on a single charge.
  • An ultra-safe and mistake-proof design with spark-proof technology and reverse polarity protection, which allows it to safely connect to any battery.
  • An ultra-bright 400 lumen LED flashlight with 7 light modes including SOS and emergency strobe.
  • Recharge your personal devices on the go, like smartphones, tablets, e-watches and more - up to 6 smartphone recharges.
  • Power 12V devices anywhere, like tire inflators, power inverters, and more.
  • Designed for gas engines up to 8 liters and diesel engines up to 6 liters for cars, SUVs, trucks, boats, RVs, and more.


WARNING: This product contains chemicals known to the state of California to cause cancer, birth defects, and/or reproductive harm. See above warning label as well as http://www.p65warnings.ca.gov for further information on Proposition 65 warnings.

Show More Show Less
NOCO - Corporate Logo
T#:2498429
Part#: GBX55
Ships in 8 Business Days
20% off MSRP $ 219.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 174.99 USD
Free Shipping
20% off MSRP
$ 219.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 174.99 USD
Free Shipping

The NOCO Boost X GBX55 is a portable lithium jump starter tailored for 12-volt batteries in vehicles with gasoline engines up to 7.5 liters and diesel engines up to 5.0 liters. This versatile tool is compatible with a wide range of vehicles, including cars, motorcycles, trucks, ATVs, boats, RVs, vans, SUVs, tractors, and more. Featuring an all-new design, the GBX55 boasts extreme jump-starting power, ensuring robust engine starts with ease. With a rating of 1750 amps, this portable lithium car battery jump starter delivers maximum energy with each start. It's not just an upgrade; it's part of our new Extreme Series, designed to offer exceptional performance and reliability.


Features: 

  • Equipped with USB-C technology that, combined with power delivery, gives you lightning-fast recharges. Completely recharges in just 1.2-hours, or go from 0% to jump starting in just 5-minutes of charge.
  • Charge everything with USB-C Power Delivery. Its internal power bank provides 60-watts of power - both in and out - to effortlessly power your favorite USB-C devices, like phones, tablets, laptops, wearables, and more.
  • We took our UltraSafe technology and made it better. It's still our simple, mistake-free design featuring spark-proof technology and reverse polarity protection, but with enhanced thermal efficiency and power management to provide better performance and longer battery life.
  • It's one of the most versatile lithium jump starters ever. Jump start all vehicle types, including cars, motorcycles, trucks, ATVs, boats, RVs, vans, SUVs, tractors, and more for up to 7.5-liter gasoline and 5.0-liter diesel engines.


WARNING: This product contains chemicals known to the state of California to cause cancer, birth defects, and/or reproductive harm. See above warning label as well as http://www.p65warnings.ca.gov for further information on Proposition 65 warnings.

Show More Show Less

NOCO - Corporate Logo
T#:641142
Part#: GENIUSPRO50
Ships in 8 Business Days
20% off MSRP $ 1,125.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 899.99 USD
Free Shipping
20% off MSRP
$ 1,125.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 899.99 USD
Free Shipping

The GENIUSPRO50 is an advanced 6-volt, 12-volt, and 24-volt fully-automatic professional smart charger, maintainer, power supply, and battery desulfator. With temperature compensation and a rating of 50 amps, it's suitable for all types of automotive, marine, and deep-cycle batteries.


Features: 

  • A multi-voltage charger - 6-volt (50-amps), 12-volt (50-amps), and 24-volt (25-amps) - for lead-acid automotive, marine, and deep-cycle batteries, including flooded, gel, AGM, and maintenance-free, plus lithium-ion.
  • Designed for pros who need absolute performance and uncompromising functionality. Featuring ultra-flexible silicone cabling - down to -40ºC - with protective nylon breaded shielding for maximum protection against abrasion.
  • A dual-voltage power supply - 12-volt (50-amp) and 24-volt (25-amp) - to maintain constant power delivery without unwanted ripple, noise, and transient spikes during ECU flashing, reprogramming, and diagnostic testing.
  • An integrated thermal sensor detects the ambient temperature and alters the charge to eliminate over-charging in hot climates and under-charging in cold climates to maximize battery life and enable fast charging.
  • Detects batteries as low as 1-volt. Or use the all-new force mode that allows you to manually begin charging dead batteries down to zero volts.
  • Automatically detects battery sulfation and acid stratification to restore lost battery performance for stronger engine starts and extended battery life. Plus, cutting-edge battery repair modes for 6-volt, 12-volt, and 24-volt batteries.


WARNING: This product contains chemicals known to the state of California to cause cancer, birth defects, and/or reproductive harm. See above warning label as well as http://www.p65warnings.ca.gov for further information on Proposition 65 warnings.

Show More Show Less
NOCO - Corporate Logo
T#:641112
Part#: GB150
Ships in 8 Business Days
20% off MSRP $ 374.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 299.99 USD
Free Shipping
20% off MSRP
$ 374.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 299.99 USD
Free Shipping

The GB150 is a compact and high-powered lithium-ion battery jump starter pack, capable of delivering an impressive 3,000 amps for jump-starting a dead battery in seconds. Equipped with patented safety technology, it ensures spark-proof connections and reverse polarity protection, making it safe and user-friendly for everyone. Not only does it serve as a potent battery booster, but it also functions as a portable power source for recharging USB devices like smartphones, tablets, and more, or for powering 12-volt devices such as tire inflators and power inverters. Designed to support a wide range of vehicles including cars, boats, RVs, trucks, and more, it's compatible with gas engines up to 9.0 liters and diesel engines up to 7.0 liters.


Features: 

  • Compact, yet powerful lithium jump starter rated at 3,000 amps up to 80 jump starts on a single charge.
  • An ultra-safe and mistake-proof design with spark-proof technology and reverse polarity protection, which allows it to safely connect to any battery.
  • An ultra-bright 500 lumen LED flashlight with 7 light modes including SOS and emergency strobe.
  • Power 12V devices anywhere, like tire inflators, power inverters, and more.
  • Recharge your personal devices on the go, like smartphones, tablets, e-watches and more - up to 6 smartphone recharges.
  • Designed for both gas engines up to 9.0 liters and diesel engines up to 7.0 liters for cars, SUVs, trucks, boats, RVs, and more.


WARNING: This product contains chemicals known to the state of California to cause cancer, birth defects, and/or reproductive harm. See above warning label as well as http://www.p65warnings.ca.gov for further information on Proposition 65 warnings.

Show More Show Less

NOCO - Corporate Logo
T#:2498428
Part#: GBX45
Ships in 8 Business Days
22% off MSRP $ 159.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 124.99 USD
Free Shipping
22% off MSRP
$ 159.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 124.99 USD
Free Shipping

The NOCO Boost X GBX45 is a portable lithium jump starter designed for 12-volt batteries in vehicles with gasoline engines up to 6.5 liters and diesel engines up to 4.0 liters. This versatile tool is compatible with a wide range of vehicles, including cars, motorcycles, trucks, ATVs, boats, RVs, vans, SUVs, tractors, and more. Featuring an all-new design, the GBX45 delivers extreme jump-starting power for robust engine starts. With a rating of 1250 amps, this portable lithium car battery jump starter releases maximum energy with every start. It's not just an upgrade; it's part of our new Extreme Series, offering exceptional performance and reliability.


Features:

  • Equipped with USB-C technology that, combined with power delivery, gives you lightning-fast recharges. Completely recharges in just 48-minutes, or go from 0% to jump starting in just 5-minutes of charge.
  • Charge everything with USB-C Power Delivery. Its internal power bank provides 60-watts of power - both in and out - to effortlessly power your favorite USB-C devices, like phones, tablets, laptops, wearables, and more.
  • We took our UltraSafe technology and made it better. It's still our simple, mistake-free design featuring spark-proof technology and reverse polarity protection, but with enhanced thermal efficiency and power management to provide better performance and longer battery life.
  • It's one of the most versatile lithium jump starters ever. Jump start all vehicle types, including cars, motorcycles, trucks, ATVs, boats, RVs, vans, SUVs, tractors, and more for up to 6.5-liter gasoline and 4.0-liter diesel engines.


WARNING: This product contains chemicals known to the state of California to cause cancer, birth defects, and/or reproductive harm. See above warning label as well as http://www.p65warnings.ca.gov for further information on Proposition 65 warnings.

Show More Show Less

NOCO - Corporate Logo
T#:855031
Part#: GENPRO10X2
Ships in 8 Business Days
21% off MSRP $ 284.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 224.99 USD
Free Shipping on orders $49 and up
21% off MSRP
$ 284.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 224.99 USD
Free Shipping on orders $49 and up

The GENPRO10X2 is an upgraded version of our GEN2 with enhanced features. This model is 19% smaller yet delivers 33% more power, making it one of the most high-performing onboard marine battery chargers NOCO has ever produced. It's a two-bank onboard battery charger with a 20-amp rating (10 amps per bank) designed for 12-volt batteries, including marine, boat, starter, and deep-cycle batteries. You can independently charge and control each battery bank using selectable charging modes such as 12V, 12V AGM, 12V Lithium, and 12V Repair Mode, suitable for all types of lead-acid and lithium-ion batteries.


Features: 

  • A two-bank on-board battery charger rated at 20-amps for 12-volt batteries, including marine, boat, starter, and deep-cycle batteries.
  • Independently charge and control each battery bank with selectable charging modes - including 12V, 12V AGM, 12V Lithium, and 12V Repair Mode - for all types of lead-acid batteries.
  • An integrated thermal sensor detects the ambient temperature and alters the charge to eliminate over-charging in hot climates and under-charging in cold climates.
  • Charges batteries as low as 1-volt. Or use the all-new force mode that allows you to take control and manually begin charging dead batteries down to zero volts.
  • Automatically detects battery sulfation and acid stratification to restore lost battery performance for stronger engine starts and extended battery life.
  • It's not just a trickle charger; it's an advanced battery maintainer. A fully automatic, worry-free battery charger for everyday use - 24/7 - with zero overcharge.
  • A simplified mounting system allows for quick and easy installations in any direction - even up-side-down - with an integrated anti-vibration backing to isolate shock, vibration, and noise.
  • A fully-sealed and waterproof onboard battery charger with an ingress protection rating of IP68, but has survived brutal life cycle testing, including thousands of hours underwater.


WARNING: This product contains chemicals known to the state of California to cause cancer, birth defects, and/or reproductive harm. See above warning label as well as http://www.p65warnings.ca.gov for further information on Proposition 65 warnings.

Show More Show Less
NOCO - Corporate Logo
T#:855029
Part#: GEN5X3
Ships in 8 Business Days
20% off MSRP $ 249.95

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 199.94 USD
Free Shipping
20% off MSRP
$ 249.95

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 199.94 USD
Free Shipping

The GEN5X3 is an upgraded version of NOCO's GENM3 with improved features. This model is 37% smaller yet delivers 43% more power, making it one of the most high-performing onboard marine battery chargers NOCO has ever produced. It's a three-bank onboard battery charger with a 15-amp rating (5 amps per bank) designed for 12-volt batteries, including marine, boat, starter, and deep-cycle batteries. You can independently charge and control each battery bank using selectable charging modes such as 12V, 12V AGM, 12V Lithium, and 12V Repair Mode, suitable for all types of lead-acid and lithium-ion batteries.


Features: 

  • A three-bank on-board battery charger rated at 15-amps for 12-volt batteries, including marine, boat, starter, and deep-cycle batteries.
  • Independently charge and control each battery bank with selectable charging modes - including 12V, 12V AGM, 12V Lithium, and 12V Repair Mode - for all types of lead-acid and lithium-ion batteries.
  • An integrated thermal sensor detects the ambient temperature and alters the charge to eliminate over-charging in hot climates and under-charging in cold climates.
  • Charges batteries as low as 1-volt. Or use the all-new force mode that allows you to take control and manually begin charging dead batteries down to zero volts.
  • Automatically detects battery sulfation and acid stratification to restore lost battery performance for stronger engine starts and extended battery life.
  • It's not just a trickle charger; it's an advanced battery maintainer. A fully automatic, worry-free battery charger for everyday use - 24/7 - with zero overcharge.
  • A simplified mounting system allows for quick and easy installations in any direction - even up-side-down - with an integrated anti-vibration backing to isolate shock, vibration, and noise.
  • A fully-sealed and waterproof onboard battery charger with an ingress protection rating of IP68, but has survived brutal life cycle testing, including thousands of hours underwater.


WARNING: This product contains chemicals known to the state of California to cause cancer, birth defects, and/or reproductive harm. See above warning label as well as http://www.p65warnings.ca.gov for further information on Proposition 65 warnings.

Show More Show Less
Ferrea - Corporate Logo
T#:163
Part#: SL1021-24
Back Ordered
$ 118.80 USD
Free Shipping
$ 118.80 USD
Free Shipping
E36 325, 328 M3 Ferrea Spring Seat Set includes 24 seats. MUST be uses with the Ferrea valve springs. Recommended to be used with the Ferrea Competition Plus Big Valves and Ferrea Titanium Retainers. See links below.

The goal at Ferrea is to create the finest valves and bearings money can buy. With a staggering array of applications for virtually every production engine in existence both gas and diesel Ferrea has the parts you need to finish your next engine project with confidence.

This item fits the following BMWs:
1992-1998 E36 BMW 323is 323ic 325i 325is 325ic 328i 328is 328ic M3
1991-1995 E34 BMW 525i
Show More Show Less


Ferrea - Corporate Logo
T#:31
Part#: E11025-24
Back Ordered
$ 7,199.76 USD
Free Shipping
$ 7,199.76 USD
Free Shipping
E36 325, 328 M3 Ferrea Titanium Retainer Set - set of 24. Recommended to be used with the Ferrea Competition Plus Big Valves. MUST be used with the Ferrea high-performance valve spring and seat kit. See links below.

The goal at Ferrea is to create the finest valves and bearings money can buy. With a staggering array of applications for virtually every production engine in existence both gas and diesel, Ferrea has the parts you need to finish your next engine project with confidence.

This item fits the following BMWs:
1992-1998 E36 BMW 325i 325is 325ic 328i 328is 328ic M3
1991-1995 E34 BMW 525i
Show More Show Less
Beru - Corporate Logo
T#:14982199
Part#: 121200405516KT
Back Ordered
$ 95.99 USD
Free Shipping on orders $49 and up
$ 95.99 USD
Free Shipping on orders $49 and up