Front Control Arm

For all 2001 to 2005 325xi and 330xi. For convenience, we have assembled this bushing carrier bracket kit, to save you time when changing our control arm bushings. It includes two bushing carriers with pre-installed bushings (one left, one right) and mounting bolts.

 These bushing brackets fit all 2001, 2002, 2003, 2004, and 2005 model BMW 325xi and 330xi.

The SPL BMW F2X/F3X Front Lower Control Arms (FLCA) provide roll center, camber, and track width adjustment for the rear wheel drive (RWD) F2X/F3X BMWs while eliminating bushing deflection resulting in sharpened steering response and driving precision.

Negative Camber Benefits

The ability to run more negative camber greatly improves the peak lateral grip available. Adding negative camber results in the tire having an optimal contact patch as the body rolls due to cornering forces. This is especially important with better tires and a must-have for anyone looking to prevent excessive outer shoulder wear (and heating) on their tires due to a lack of camber.

Wider Front Track Width Benefits

Further handling improvements can be had by increasing the front track width from the factory 60.5" (F3X) or 59.9" (F2X) to be closer to the M3's 62.2". If you applied the M3's width to the M340i it would reduce the outer front tire loading by roughly 20 lbs and apply it to the inner front tire. The result would be greater peak grip (~0.04G), improved stability, and faster lap times.

Roll Center Correction Benefits

Lowering the F2X/F3X results in a greater distance between the front roll center and the center of gravity. This acts like a longer lever, creating more body roll, bumpsteer, and requiring additional static camber angle to maintain the same handling. The SPL front lower control arms allow the roll center to be corrected for a wide range of ride heights to improve handling and stability.

The lower control arms come with a ride height sensor bracket to maintain the factory ride height sensor location, regardless of length of the arm to keep those finicky BMW chassis electronics happy.

Benefits

Adjustable Camber, Roll Center, and Track Width

Eliminates Bushing Deflection

Improved Tire Life with Ideal Camber Settings

Lightweight, High-Strength Construction

Stackable 304SS Roll Center Spacers in 1/8" and 1/4" Sizes

US Made, PTFE Lined FK Rod Ends 

Materials

6061-T6 aluminum black anodized arm, clamps, and spacers

4130 CrMo electroless nickel-plated double adjuster

Ti6Al4V titanium socket head cap screws

304 stainless steel roll center and knuckle spacers

5/8" 4140 CrMo stud

FK PTFE-lined spherical bearings (F1 spec, self-cleaning)

Suitable for all uses, from daily driver to race car.

The SPL BMW F2X/F3X Front Lower Control Arms (FLCA) provide roll center, camber, and track width adjustment for the xDrive-equipped F2X/F3X BMWs while eliminating bushing deflection resulting in sharpened steering response and driving precision.

The ability to run more negative camber greatly improves the peak lateral grip available. Adding negative camber results in the tire having an optimal contact patch as the body rolls due to cornering forces. This is especially important with better tires and a must-have for anyone looking to prevent excessive outer shoulder wear (and heating) on their tires due to a lack of camber.

The lower control arms come with a ride height sensor bracket to maintain the factory ride height sensor location, regardless of length of the arm to keep those finicky BMW chassis electronics happy.

Benefits

Adjustable Camber, Roll Center, and Track Width

Eliminates Bushing Deflection

Improved Tire Life with Ideal Camber Settings

Lightweight, High-Strength Construction

Stackable 304SS Roll Center Spacers in 1/8" and 1/4" Sizes

US Made, PTFE Lined FK Rod Ends 

Materials

6061-T6 aluminum black anodized arm, clamps, and spacers

4130 CrMo electroless nickel-plated double adjuster

Ti6Al4V titanium socket head cap screws

304 stainless steel roll center and knuckle spacers

5/8" 4140 CrMo stud

FK PTFE-lined spherical bearings (F1 spec, self-cleaning)

Suitable for all uses, from daily driver to race car.

Control arm bushings play a key role in connecting the wheels to the chassis of the vehicle. Tasked with keeping suspension geometry in check while absorbing noise, vibration, and harshness (NVH) factory rubber bushings were engineered to provide a balance of comfort and control. As a factory bushing ages, it becomes brittle and begins to harden. When this happens the bushing will actually shrink and allow excess play in the suspension joint. This is typically felt by a sudden jerk forward after the car comes to a stop and is a leading cause of "sloppy" or "loose" suspension feel. By replacing the bushing with a full polyurethane unit or using a bushing insert, this play is eliminated since the suspension joint is being supported by a much stiffer material that will not harden or shrink over time. Additionally, the inherent stiffness of the urethane material translates body forces much more directly. This means steering inputs from the driver are effectively transferred to the wheels and vital road information is transmitted properly from the wheels to the driver.

Powerflex Black Series bushings are the ultimate in track and race bushings. Featuring 95A durometer polyurethane, Black Series bushings are 25% stiffer than street bushings. Engineered to perform, Powerflex performance polyurethane control arm bushings offer a supreme level of control, while still providing enough comfort for the street, with advanced polyurethane that reduces NVH that often accompanies lesser bushings. Expect improved steering feel, turn in, more responsive handling and overall improved chassis composure with Powerflex performance polyurethane control arm bushings.

Poweflex is a leading manufacturer of aftermarket suspension bushings. Using state of the art design and manufacturing, all replacement bushings are engineered to out-perform and out-last the ones that came in the car. Each line of bushings is meticulously tested and then re-tested to ensure perfect fitment and enduring quality through the life of the vehicle. A full lifetime warranty backs every one of their products and demonstrates the level of confidence and commitment Powerflex has to their customers. 

This part fits the following BMWs:
1998 - 2004 E39 Touring 525i 528i 540i
1996 - 2004 E39 Sedan 525i 528i 530i 540i 

Control arm bushings play a key role in connecting the wheels to the chassis of the vehicle. Tasked with keeping suspension geometry in check while absorbing noise, vibration, and harshness (NVH) factory rubber bushings were engineered to provide a balance of comfort and control. As a factory bushing ages, it becomes brittle and begins to harden. When this happens the bushing will actually shrink and allow excess play in the suspension joint. This is typically felt by a sudden jerk forward after the car comes to a stop and is a leading cause of "sloppy" or "loose" suspension feel. By replacing the bushing with a full polyurethane unit or using a bushing insert, this play is eliminated since the suspension joint is being supported by a much stiffer material that will not harden or shrink over time. Additionally, the inherent stiffness of the urethane material translates body forces much more directly. This means steering inputs from the driver are effectively transferred to the wheels and vital road information is transmitted properly from the wheels to the driver.

Powerflex street bushings are ideal for street driven vehicles and those that see occasional autocross or track time. Need bushings for a dedicated track car? Powerflex Black Series bushings are the ultimate in track and race bushings. Featuring 95A durometer polyurethane, Black Series bushings are 25% stiffer than street bushings. Engineered to perform, Powerflex performance polyurethane control arm bushings offer a supreme level of control, while still providing enough comfort for the street, with advanced polyurethane that reduces NVH that often accompanies lesser bushings. Expect improved steering feel, turn in, more responsive handling and overall improved chassis composure with Powerflex performance polyurethane control arm bushings.

Poweflex is a leading manufacturer of aftermarket suspension bushings. Using state of the art design and manufacturing, all replacement bushings are engineered to out-perform and out-last the ones that came in the car. Each line of bushings is meticulously tested and then re-tested to ensure perfect fitment and enduring quality through the life of the vehicle. A full lifetime warranty backs every one of their products and demonstrates the level of confidence and commitment Powerflex has to their customers. 

Control arm bushings play a key role in connecting the wheels to the chassis of the vehicle. Tasked with keeping suspension geometry in check while absorbing noise, vibration, and harshness (NVH) factory rubber bushings were engineered to provide a balance of comfort and control. As a factory bushing ages, it becomes brittle and begins to harden. When this happens the bushing will actually shrink and allow excess play in the suspension joint. This is typically felt by a sudden jerk forward after the car comes to a stop and is a leading cause of "sloppy" or "loose" suspension feel. By replacing the bushing with a full polyurethane unit or using a bushing insert, this play is eliminated since the suspension joint is being supported by a much stiffer material that will not harden or shrink over time. Additionally, the inherent stiffness of the urethane material translates body forces much more directly. This means steering inputs from the driver are effectively transferred to the wheels and vital road information is transmitted properly from the wheels to the driver.

Powerflex Black Series bushings are the ultimate in track and race bushings. Featuring 95A durometer polyurethane, Black Series bushings are 25% stiffer than street bushings. Engineered to perform, Powerflex performance polyurethane control arm bushings offer a supreme level of control, while still providing enough comfort for the street, with advanced polyurethane that reduces NVH that often accompanies lesser bushings. Expect improved steering feel, turn in, more responsive handling and overall improved chassis composure with Powerflex performance polyurethane control arm bushings.

Poweflex is a leading manufacturer of aftermarket suspension bushings. Using state of the art design and manufacturing, all replacement bushings are engineered to out-perform and out-last the ones that came in the car. Each line of bushings is meticulously tested and then re-tested to ensure perfect fitment and enduring quality through the life of the vehicle. A full lifetime warranty backs every one of their products and demonstrates the level of confidence and commitment Powerflex has to their customers. 

This part fits the following BMWs:
1996 - 2004 E39 Sedan 540i 
1998 - 2004 E39 M5

These SPL Parts Front Lower Street Control arms replace OEM Part numbers 31122405860 and 31122405859

SPL Parts is a performance suspension manufacturer that designs and tests their products all in-house here in the USA. Additionally, all materials used are sourced from American suppliers to ensure consistently high quality products. SPL Parts products are all constructed using chromoly seamless straight tubing, DOM mandrel bent tubing, and 6061 and 2024 aluminum for high strength and quality. All TIG welding and CNC machining is also done locally by professional welders and machine shops to meet exact quality standards and tolerance specifications. For anything from racing to street driven needs, SPL Parts offer an amazing line of premium quality products that are perfect to get your car back in spec.

These SPL front lower control arms open up a wide range of adjustment for roll center, camber, and track width adjustment and allow for full articulation with the correct ball joint angle. Instead of using traditional jam nuts, the main arm is slotted to allow the use of pinch bolts and SPL rotating clamps on their exclusive adjuster, making it easier to lock in track width and camber specifications.

*includes headlight adjusting rod

SPL Parts Billet Lower Control/Trailing Arms Feature:

• Lightweight Aluminum and Titanium construction
• Electroless nickel plated 4130 Chromoly Double Adjuster for quick adjustment
• Correct ball joint angle for full articulation
• Rotating Clamp design allows for easy access to lock down alignment settings
• Low friction 3 piece Teflon lined FK sphericals and Heim joints/rod ends
• Multiple size Stainless Steel roll center spacers for precise adjustment

Fits the following BMWs:
2006-2013 E9X BMW RWD Submodels
2008-2013 E82/88 BMW All  Submodels