Front Control Arm

The SPL BMW F2X/F3X Front Lower Control Arms (FLCA) provide roll center, camber, and track width adjustment for the rear wheel drive (RWD) F2X/F3X BMWs while eliminating bushing deflection resulting in sharpened steering response and driving precision.

Negative Camber Benefits

The ability to run more negative camber greatly improves the peak lateral grip available. Adding negative camber results in the tire having an optimal contact patch as the body rolls due to cornering forces. This is especially important with better tires and a must-have for anyone looking to prevent excessive outer shoulder wear (and heating) on their tires due to a lack of camber.

Wider Front Track Width Benefits

Further handling improvements can be had by increasing the front track width from the factory 60.5" (F3X) or 59.9" (F2X) to be closer to the M3's 62.2". If you applied the M3's width to the M340i it would reduce the outer front tire loading by roughly 20 lbs and apply it to the inner front tire. The result would be greater peak grip (~0.04G), improved stability, and faster lap times.

Roll Center Correction Benefits

Lowering the F2X/F3X results in a greater distance between the front roll center and the center of gravity. This acts like a longer lever, creating more body roll, bumpsteer, and requiring additional static camber angle to maintain the same handling. The SPL front lower control arms allow the roll center to be corrected for a wide range of ride heights to improve handling and stability.

The lower control arms come with a ride height sensor bracket to maintain the factory ride height sensor location, regardless of length of the arm to keep those finicky BMW chassis electronics happy.

Benefits

Adjustable Camber, Roll Center, and Track Width

Eliminates Bushing Deflection

Improved Tire Life with Ideal Camber Settings

Lightweight, High-Strength Construction

Stackable 304SS Roll Center Spacers in 1/8" and 1/4" Sizes

US Made, PTFE Lined FK Rod Ends 

Materials

6061-T6 aluminum black anodized arm, clamps, and spacers

4130 CrMo electroless nickel-plated double adjuster

Ti6Al4V titanium socket head cap screws

304 stainless steel roll center and knuckle spacers

5/8" 4140 CrMo stud

FK PTFE-lined spherical bearings (F1 spec, self-cleaning)

Suitable for all uses, from daily driver to race car.

These SPL Parts Front Lower Street Control arms replace OEM Part numbers 31122405860 and 31122405859

SPL Parts is a performance suspension manufacturer that designs and tests their products all in-house here in the USA. Additionally, all materials used are sourced from American suppliers to ensure consistently high quality products. SPL Parts products are all constructed using chromoly seamless straight tubing, DOM mandrel bent tubing, and 6061 and 2024 aluminum for high strength and quality. All TIG welding and CNC machining is also done locally by professional welders and machine shops to meet exact quality standards and tolerance specifications. For anything from racing to street driven needs, SPL Parts offer an amazing line of premium quality products that are perfect to get your car back in spec.

These SPL front lower control arms open up a wide range of adjustment for roll center, camber, and track width adjustment and allow for full articulation with the correct ball joint angle. Instead of using traditional jam nuts, the main arm is slotted to allow the use of pinch bolts and SPL rotating clamps on their exclusive adjuster, making it easier to lock in track width and camber specifications.

*DOES NOT include headlight adjusting rod

SPL Parts Billet Lower Control/Trailing Arms Feature:

• Lightweight Aluminum and Titanium construction
• Electroless nickel plated 4130 Chromoly Double Adjuster for quick adjustment
• Correct ball joint angle for full articulation
• Rotating Clamp design allows for easy access to lock down alignment settings
• Low friction 3 piece Teflon lined FK sphericals and Heim joints/rod ends
• Multiple size Stainless Steel roll center spacers for precise adjustment

Fits the following BMWs:
2006-2013 E9X BMW RWD Submodels
2008-2013 E82/88 BMW All  Submodels

Over the years, the road takes a serious toll on your suspension. Pot holes, speed bumps, and road hazards all contribute to a sloppy, weak suspension. To give a better feel to your driving experience, change components as they wear to improve safety and ride comfort.

One item to replace is the control arm. After years of service, the non-serviceable ball joints and other components can begin to wear out. Because some components cannot be replaced, the only solution is replacement of the entire arm.

If replacing any part of your front or rear suspension, it is best to either do it in pairs (both left and right sides), or examine parts that are prone to failure. This will provide the most service life out of replacement parts and assure they are all performing properly.

Referred to as a wishbone by BMW.

These SPL Parts Front Lower Street Control arms replace OEM Part numbers 31122405860 and 31122405859

SPL Parts is a performance suspension manufacturer that designs and tests their products all in-house here in the USA. Additionally, all materials used are sourced from American suppliers to ensure consistently high quality products. SPL Parts products are all constructed using chromoly seamless straight tubing, DOM mandrel bent tubing, and 6061 and 2024 aluminum for high strength and quality. All TIG welding and CNC machining is also done locally by professional welders and machine shops to meet exact quality standards and tolerance specifications. For anything from racing to street driven needs, SPL Parts offer an amazing line of premium quality products that are perfect to get your car back in spec.

These SPL front lower control arms open up a wide range of adjustment for roll center, camber, and track width adjustment and allow for full articulation with the correct ball joint angle. Instead of using traditional jam nuts, the main arm is slotted to allow the use of pinch bolts and SPL rotating clamps on their exclusive adjuster, making it easier to lock in track width and camber specifications.

*includes headlight adjusting rod

SPL Parts Billet Lower Control/Trailing Arms Feature:

• Lightweight Aluminum and Titanium construction
• Electroless nickel plated 4130 Chromoly Double Adjuster for quick adjustment
• Correct ball joint angle for full articulation
• Rotating Clamp design allows for easy access to lock down alignment settings
• Low friction 3 piece Teflon lined FK sphericals and Heim joints/rod ends
• Multiple size Stainless Steel roll center spacers for precise adjustment

Fits the following BMWs:
2006-2013 E9X BMW RWD Submodels
2008-2013 E82/88 BMW All  Submodels

Control arms, and their integrated ball joints, are some of the most crucial components on a BMW suspension. The control arms literally control the wheel and suspension as they go through their range of motions. A faulty or worn control arm or ball joint is a very dangerous and potentially life-threatening problem so make sure they are inspected and replaced at regular intervals. For a street-driven car we advise yearly inspection and a full replacement every 3-4 years. For track-driven cars these should be inspected before every event and replaced every two years.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

This is the OEM Front Right Lower Control Arm for E39 BMW 525i 528i 530i 1997-2003.

This item fits the following BMWs:
1997-2003 E39 5 Series BMW 525i 528i 530i & Wagons