BMW Sway Bar End Links

These adjustable rear links are only required when using sway bar / swaybars with a suspension with a very low ride height, where it may be necessary to adjust the length of the end links for proper sway bar clearance from the drive axles or other suspension components. These suspensions are usually found only on race cars but this may also apply to street cars with sport springs/sport coil overs that are lowered a lot. On most street cars lowered 1.5" or less, the stock links will be fine.

These end links feature a Heim joint, which allows enough lateral movement when disconnected to adjust the length of the link without removing the entire link from the car. This is particularly helpful when eliminating or adjusting preload while tuning the suspension. Similar links without this joint, can't be adjusted without totally removing the link from the car.

Built-in grease fittings allow for occasional lube, and a packet of grease is included. These links are sold as a set, and include two end links and hardware for H&R and TMS sway bars (other brands may not need the hardware). 

At their shortest setting they are 2.875" hole to hole and on their longest setting they are 3.5" hole to hole.

*Note: these links will not work with factory or non-adjustable Eibach sway bars.

BMW F8X F2X F30 034Motorsport Billet Adjustable Front Sway Bar End Links offer superior performance by replacing the flimsy OEM sway bar end links with high-quality, adjustable spherical end links. These end links are engineered to ensure precise transfer of suspension energy to the sway bar, enhancing both street and track performance. Key features include:

• CNC machined from 6061-T6 aluminum with an anodized black finish for durability
• Zinc-plated steel ball joints for increased strength
• Spherical design eliminates deflection and ensures proper articulation
• Motorsport quality Aurora spherical bearings with self-lubricating Teflon race lining
• +/- 0.75" of adjustability (1.5" total adjustment range) for precise sway bar preload adjustment
• Essential for corner balancing lowered vehicles and optimizing sway bar reaction time
• Compatible with all stock and aftermarket sway bars
• Sold in pairs with all necessary hardware included

Lowering your BMW does wonders for appearance and handling, but it also changes suspension geometry in ways that can hurt performance. As ride height changes, angles between the sway bar, control arms, and axles shift, which can cause binding, poor fitment, and added stress on the factory fixed-length end links. This is especially noticeable on cars equipped with coilover suspension, where slight height differences side to side can preload the sway bar and lead to inconsistent handling.

Our team of dedicated BMW enthusiasts set out to remedy this common issue with a set of Adjustable Rear Sway Bar End Links. Designed with performance in mind, they offer a fully adjustable range from 100mm to 120mm, helping eliminate preload, restore proper suspension alignment, and improve overall sway bar function. Constructed from high-quality billet aluminum, these end links are built to outlast the factory cast components and are finished with a black anodized coating for excellent corrosion resistance. Laser-etched wrench size markings allow for quick, easy adjustments while installed on the vehicle. Unlike the factory design, these end links use spherical rod ends at the control arm for increased responsiveness and a more direct handling feel. A unique knurled bushing design also ensures compatibility with the OEM sway bar, offering a first-to-market solution for enthusiasts looking to retain factory components.

Features & Benefits:

Adjustable from 100mm to 120mm Strong 6061-T6 billet aluminum construction Black anodized finish resists corrosion Spherical rod ends improve response and handling feel Polyurethane bushing with knurled bore helps retain grease Fits factory rear sway bars on E23, E24, E28, E30, and E36 Laser-etched markings for quick and easy adjustments

The MMX Performance adjustable drop links are a great choice for any lowered or hard-driven BMW to zero the pre-load on your anti-roll bar geometry. Plus, by replacing the stock rubber joints with motorsport-spec ball joint ends, you'll add valuable stiffness and precision to handling and steering dynamics.

The sway bar end link attaches the front anti-roll bar ends to the front damper. The OEM links were made the length they are for a reason, to complement the standard ride height.

When your ride height is altered, your vehicle's anti-roll bar ends are pulled up. With around 40mm of adjustable length, plus left and right threaded ends for easy length adjustment, the MMX adjustable sway bar end links allow you to adjust back to zero preload on your anti-roll bar - allowing it to operate exactly as it should once again.

Motorsport-spec ball joint ends using high-strength Teflon-lined steel means a much more direct response when turning into corners. By replacing the soft rubber bushing in the factory links with these motorsport-spec ball joints, cornering and steering responses are immediately sharpened. Importantly, rubber dust boots are fitted to protect the joints from road dirt and salt accumulation.

The lightweight CNC-machined T6-6061 aluminum bodies are anodized in our beautiful MMX gloss black coating to look good and stay looking good.

Features:

Manufactured in the UK from Aircraft grade T6-6061 aluminum billet.

Complete OE replacements

Anodized in signature MMX Gloss black.

Heavy-duty ball joints to ensure a long life span.

325-365mm adjustment range.

Direct replacement – can be used with either factory or Aftermarket rear anti-roll bar, and returned to standard at any time.

Designed with one aim in mind: to help achieve optimum suspension performance and geometric accuracy, and thus increase the effectiveness of your rear anti-roll bar.

Each heavy-duty, high-articulation rear end link attaches the rear anti-roll bar ends to the lower suspension arm. Replacing the failure-prone, weak plastic OEM links with our rigid billet aluminum links greatly reduces flex and allows a sharp, uncompromised transfer of suspension movement through to the sway bar.

As well as the link itself, extra stiffness and precision comes from replacing the flex-prone stock plastic ball joint with motorsport-spec ball joints. An especially valuable upgrade on older, higher mileage car.

Features:

Manufactured from Aircraft grade T6-6061 aluminum billet.

Complete OE replacements.

Our single-threaded ends make for easy length adjustment in-situ without having to detach and re-attach.

Each heavy-duty, high-articulation rear drop link.

Anodized in signature MMX Gloss black.

Heavy-duty ball joints to ensure a long life span.

Kit complete with everything you need.

Can be used with either factory or Aftermarket rear anti-roll bar, and returned to standard at any time.

Rubber boots for longevity and durability.