BMW Suspension Bushings & Mounts

Replacing your struts and shocks? Don't forget the bushings! The rubber mounts for the shocks will go bad over time, especially if you drive hard or the roads are particularly rough. The shock mounts locate the front struts and rear shocks to the car - providing a quiet and vibration-free buffer between the road and the cabin. Shock mounts and bushings can wear out just like any other rubber part on the car. This leads to more noise and harshness reaching the chassis and may complicate your new suspension install. When installing new shocks, that is the perfect time to also replace the mounts. There is no additional time to install them, no special tools required, and doesn't take any extra time! If you re-use the original mounts you have the risk of them failing before your next shock replacement, doubling your labor costs. 

This item fits the following BMWs: 
2006-2012 E9X BMW All xi models - 325xi 328xi 330xi 335xi

This package of OEM E82 E90 E92 diff mounts replaces the stock rubber diff bushings. On a tuned 335i you may have noticed more driveline shudder or problems hooking up during hard launches. What happens is the stock rubber bushings are under constant flex as engine torque is transmitted through the differential. Under normal driving with a stock car the bushings are rarely stressed. But factor in significant additional torque from a tuned N54/N55 and the stock rubber will quickly show its weaknesses. You may have even broken a diff bolt or two as the heavy differential shifts around. Even non-turbo E82 and E9X models may benefit from fresh bushings.

This is a set of stock rubber bushings, made by OEM supplier Lemforder. They are the same as the Genuine BMW E9X diff mount bushings, but without the more expensive branding. If you're turned off by potential side effects of urethane or Delrin then the OEM diff mounts are your best option. The OEM mounts fit and perform just like the originals so there is no second guessing their quality. If you're looking for an upgrade we offer E9X solid Delrin and aluminum diff mounts that work well, even in street applications.

E9X Diff Mount Set includes:

• 33176760287 x 2, front differential mount
• 33176770866 x 1, rear differential mount
• (new hardware is optional and can be ordered separately below)
  
  This item fits the following BMWs:
  2008-2012 E82 BMW 128i 135i
  2006-2011 E90 BMW 325i 325xi 328i 328xi 328i xDrive 330i 330xi 335d 335i 335xi 335i xDrive - Sedan
  2006-2012 E91 BMW 325xi 328i 328xi 328i xDrive - Wagon
  2007-2013 E92 BMW 328i 328xi 328i xDrive 335i 335is 335xi 335i xDrive - Coupe
  2007-2013 E93 BMW 328i 335i - Convertible

This package allows you to build your own rear bushing package to cover the parts you want to replace. As these cars age, they require a number of suspension bushings to be replaced. Bushing replacement not only keeps the car in its top form, it also makes the car safer. Depending on the work, it may be logical to replace all of the bushings in the rear suspension (there are 19 total). This is especially true if you are pulling the subframe out to do the floor reinforcement or if you're doing a diff install. Turner Motorsport is a big believer in using rubber bushings for street cars (with the exception of solid subframe mounts, see further below). Urethanes, Delrin, or aluminum are generally good for reducing compliance and limiting deflection - attributes that don't really work well on roads filled with potholes, railroad crossings, cracks, and expansion joints. The rubber bushings maintain the factory ride/handling traits that won the E46 praise all over the world. Every bushing will need maintenance or replacement at some point and rubber has proven to last the longest and need less maintenance than anything else, even urethane. And unless competitive driving is your goal, the harder materials are only a gimmick.

Any major overhaul of the rear suspension should include new subframe mounts. The worn rubber mounts contribute to rear subframe-floor failure when the deflection in the mount is transferred to the chassis. Rubber mounts are only OK for street cars that don't see aggressive driving, autocross, or track use. For any enthusiastic driving, we strongly recommend our solid aluminum subframe mounts even on the street. They have zero deflection and will not contribute to rear floor failures. And if you leave rubber in the rest of the suspension your ride comfort will not suffer.

Individual Item Descriptions:

• Trailing Arm Bushings and Limiters (33322228153 and TSU9990001) - our OEM rubber replacement trailing arm bushings (RTABs) are a perfect fit and help maintain rear toe alignment. The Limiters prevent premature bushing wear.
• Rear Inner Control Arm Bushings (upper 33321092247 and lower 33326770824) - new stock inner rubber bushings for the upper spring arm and the lower camber arm. These do not wear out very quickly but should be replaced as a 'While you're in there...' job.
• Rear Outer Control Arm Bushings (upper and lower) (33326775551) - new stock outer ball joints for the upper spring arm and the lower camber arm. These are the standard ball joint design and last a very long time. Check for play with a pry bar and replace as needed.
• Rear Shock Mounts - Choose from several types of RSM upgrades. If your mounts have not been replaced in the last 40,000 miles, now is the perfect time. Skip this option if you recently replaced mounts or already have an upgraded mount.
• Differential mounts (33176770788 and 33176751808) - Now is a great time to replace the rubber-isolated mounts. This is another low-wear mount but it can be changed easily, and is a low cost item. Solid diff mounts are streetable with only a minimal increase in NVH.
• Rear subframe mounts (33316770783, 33316770784, 33316770781 x 2) - The heart of the rear suspension, the subframe (or carrier) mounts located the entire rear suspension to the car. There are four mounts in total and bolt up into the rear floor. Worn subframe mounts are one of the leading contributors to rear floor-subframe failure. As the mounts flex, so does the sheetmetal of the chassis, which will fatigue the sheetmetal and crack the spot welds. Therefore, replacement of the subframe mounts is critical and a must when doing the subframe reinforcement or repair. Solid aluminum mounts are streetable with no increase in NVH.

This item fits the following BMWs:
1999-2006 E46 BMW 323i 323ci 325i 325ci 325xi 328i 328ci 330i 330ci 330xi

This kit includes Turner Motorsport solid aluminum differential race mounts pre installed in the differential cover for a quick install. These mounts where developed by Turner Motorsport for their Grand-Am Cup E46 M3 race cars, the advantages of solid aluminum mounts is increased suspension & drivetrain response, less drivetrain loss resulting in more wheel horsepower, and longevity - they effectively last forever. These CNC-machined mounts are a direct replacement for the stock rubber pieces, and have been lightened to remove excess weight. 

This strut and shock mount package covers the front and rear rubber mounts and bushings commonly replaced during a strut and shock install. While you're installing new front struts and rear shocks these are easily installed - there's no additional labor and special tools are not required. Since these pieces are mostly rubber, they dry up and crack over time. Re-using them lead to problems with fitment or noise, and may have safety issues as well. These mounts and pads are the perfect complement to your new shocks to help restore your car's handling and performance. 

We sell the basic strut and shock mount package, which includes:

• Front strut mounts (also known as guide support)
• Front strut reinforcement plates (to prevent cracking and deforming of the front strut towers)
• Front strut tower paper washer gaskets
• Front and rear self-locking mounting nuts
• Rear Lifetime Warranty 'Repair Shop' shock mounts
• Rear shock mount reinforcements (to prevent cracking of shock towers)
• Rear shock mount gaskets

In addition, you can add the front spring pads, front bump stops, front dust boots, rear bump stops, and rear dust boots if needed. But please note that some shocks and coil overs come with all or some of these pieces already. If in doubt, check with your supplier on what is included. 

We offer three varieties of the rear shock mounts - OEM, Repair Shop, and HP alum-rubber. We recommend either the Repair Shop or HP mounts because the stock OEM design has a flaw that can lead to premature failure of the mounts. The Repair Shop and HP mounts use a different design that will last longer and the Repair Shop mounts also have a lifetime warranty! 

This item fits the following BMWs:
1995 E36 BMW M3